Direct Electrochemistry and Electrocatalysis of Hemoglobin/ZnO‐Chitosan/nano‐Au Modified Glassy Carbon Electrode

The highly efficient H₂O₂ biosensor was fabricated on the basis of the complex films of hemoglobin (Hb), nano ZnO, chitosan (CHIT) dispersed solution and nano Au immobilized on glassy carbon electrode (GCE). Biocompatible ZnO‐CHIT composition provided a suitable microenvironment to keep Hb bioactivity (Michaelis‐Menten constant of 0.075 mmol L^?1). The presence of nano Au in matrix could effectively enhance electron transfer between Hb and electrode. The electrochemical behaviors and effects of solution pH values were carefully examined in this paper. The (ZnO‐CHIT)‐Au‐Hb/GCE demonstrated excellently electrocatalytical ability for H₂O₂. This biosensor had a fast response to H₂O₂ less than 4 s and excellent linear relationships were obtained in the concentration range from1.94×10^?7 to 1.73×10^?3 mol L^?1 with the detection limit of 9.7×10^?8 mol L^?1 (S/N=3) under the optimum conditions. Moreover, the stability and reproducibility of this biosensor were evaluated with satisfactory results.     

Mechanistic disparity in the electron transfer reactions of thiosulfate with di‐μ‐oxo‐bis(1,4,8,11‐tetraazacyclotetradecane)‐dimanganese(III,IV) and di‐μ‐oxo‐bis(1,4,7,10‐tetraazacyclododecane)‐dimanganese(III,IV) complexes

A comparative kinetic study of the reactions of two mixed valence manganese(III,IV) complexes of macrocyclic ligands, [L¹Mn^IV(O)₂Mn^IIIL¹], 1 (L¹ = 1,4,8,11‐tetraazacyclotetradecane) and [L²Mn^IV(O)₂Mn^IIIL²], 2 (L² = 1,4,7,10‐tetraazacyclododecane) with thiosulfate has been carried out by spectrophotometry in aqueous buffer at 30°C. Reaction between complex 1 and thiosulfate follows a first‐order rate saturation kinetics. The pH dependency and kinetic evidences suggest the participation of two complex species of Mn^III(μ‐O)₂Mn^IV under the experimental conditions. Detailed kinetic study shows that reduction of 2 proceeds through an autocatalytic path where the intermediate (Mn^III)₂ species has been assumed to catalyze the reaction. The difference in the reaction mechanisms is ascribed to the difference in stability of the intermediate complex species, the evidence for which comes from the electrochemical behavior of the complexes and time dependent EPR spectroscopic measurements during the reduction of 2 . © 2003 Wiley Periodicals, Inc. Int J Chem Kinet 36: 119–128, 2004     

A comparative kinetic study for the oxidation of 2‐mercaptoethanol by di‐μ‐oxo‐bis(1,4,7,10‐tetraazacyclododecane)‐dimanganese(III,IV) and di‐μ‐oxo‐bis(1,4,8,11‐tetraazacyclotetradecane)‐dimanganese(III,IV) complexes: Influence of copper(II)

A comparative kinetic study of the reactions of two mixed valence manganese(III,IV) complexes with macrocyclic ligands, [L¹Mn^IV(O)₂Mn^IIIL¹], 1 (L¹ = 1,4,7,10‐tetraazacyclododecane) and [L²Mn^IV(O)₂Mn^IIIL²], 2 (L² = 1,4,8,11‐tetraazacyclotetradecane) with 2‐mercaptoethanol (RSH) has been carried out by spectrophotometry in aqueous buffer at (30 ± 0.1)°C. Rate of the reactions between the oxidants and the reductant was found to be negligibly slow with no systematic dependence on either redox partners. Externally added copper(II) (usually 5 × 10^?7 mol dm^?3), however, increases the rate of the reduction of 1 and 2 significantly. In the presence of catalytic amount of copper(II), the rate of the reaction is nearly proportional to [RSH] at lower concentration of the reductant but follows a saturation kinetics at higher concentration of the latter for the reaction between 1 and the thiol. Reaction rate was found to be strongly influenced by the variation of acidity of the medium and the observed kinetics suggests that the two reductant species ([Cu(RSH)]²⁺ and [Cu(RS)]⁺) are significant for the reaction between 1 and the thiol. The dependence of the rate on [RSH] for the reduction of 2 by the thiol was complex and rationalized considering two equilibria involving the catalyst (Cu²⁺) and the reductant. The pH rate profile suggests that both the μ‐O protonated [Mn^III(O)(OH)Mn^IV] and the deprotonated [Mn^III(O)₂Mn^IV] forms of the oxidant 2 become important. The kinetic results presented in this study indicate the domination of outer‐sphere path. © 2003 Wiley Periodicals, Inc. Int J Chem Kinet 36: 129–137, 2004     

Anodic Stripping Voltammetric Determination of Mercury(II) in Water Using a 4‐Tert‐Butyl‐1‐(Ethoxycarbonylmethoxy)Thiacalix[4]Arene Modified Glassy Carbon Electrode

A glassy carbon electrode coated the film of 4‐tert‐butyl‐1‐(ethoxycarbonylmethoxy)thiacalix[4]arene is designed for the determination of trace amounts of Hg²⁺. Compared with bare glassy carbon electrode, the modified electrode can improve the measuring sensitivity of Hg²⁺. Under the optimum experimental condition, the modified electrode in 0.1 mol L^?1 H₂SO₄ + 0.01 mol L^?1 KCl solution shows a linear voltammetric response in the range of 8.0 × 10^?9 ～ 3.0 × 10^?6 mol L^?1 with detection limit 5.0 × 10^?9 mol L^?1 for Hg²⁺. The high sensitivity, selectivity, and stability of modified electrode also prove its practical application for a simple, rapid and economical determination of Hg²⁺ in water samples.     

Direct Electrochemistry and Electrocatalysis of Hemoglobin Based on Nafion‐Room Temperature Ionic Liquids‐Multiwalled Carbon Nanotubes Composite Film

A robust and effective composite film combined the benefits of Nafion, room temperature ionic liquid (RTIL) and multi‐wall carbon nanotubes (MWNTs) was prepared. Hemoglobin (Hb) was successfully immobilized on glassy carbon electrode surface by entrapping in the composite film. Direct electrochemistry and electrocatalysis of immobilized Hb were investigated in detail. A pair of well‐defined and quasi‐reversible redox peaks of Hb was obtained in 0.10 mol·L^?1 pH 7.0 phosphate buffer solution (PBS), indicating that the Nafion‐RTIL‐MWNTs film showed an obvious promotion for the direct electron transfer between Hb and the underlying electrode. The immobilized Hb exhibited an excellent electrocatalytic activity towards the reduction of H₂O₂. The catalysis current was linear to H₂O₂ concentration in the range of 2.0×10^?6 to 2.5×10^?4 mol·L^?1, with a detection limit of 8.0×10^?7 mol·L^?1 (S/N=3). The apparent Michaelis‐Menten constant (K_m^app) was calculated to be 0.34 mmol·L^?1. Moreover, the modified electrode displayed a good stability and reproducibility. Based on the composite film, a third‐generation reagentless biosensor could be constructed for the determination of H₂O₂.     

Simultaneous Determination of Dopamine and Ascorbic Acid Using the Nano‐Gold Self‐Assembled Glassy Carbon Electrode

Electrochemical behavior of dopamine (DA) was investigated at the gold nanoparticles self‐assembled glassy carbon electrode (GNP/LC/GCE), which was fabricated by self‐assembling gold nanoparticles on the surface of L ‐cysteine (LC) modified glassy carbon electrode (GCE) via successive cyclic voltammetry (CV). A pair of well‐defined redox peaks of DA on the GNP/LC/GCE was obtained at E_pa=0.197 V and E_pc=0.146 V, respectively. And the peak separation between DA and AA is about 0.2 V, which is enough for simultaneous determination of DA and AA. The peak currents of DA and AA were proportional with their concentrations in the range of 6.0×10^?8–8.5×10^?5 mol L^?1 and 1.0×10^?6–2.5×10^?3 mol L^?1, with the detection limit of 2.0×10^?8 mol L^?1 and 3.0×10^?7 mol L^?1 (S/N=3), respectively. The modified electrode exhibits an excellent reproducibility, sensibility and stability for simultaneous determination of DA and AA in human serum with satisfactory result.     

Evaluation of the Oxo‐bridged Dinuclear Ruthenium Ammine Complex as Redox Mediator in an Electrochemical Biosensor

The mediation of electron‐transfer by oxo‐bridged dinuclear ruthenium ammine [(bpy)₂(NH₃)Ru^III(µ‐O)Ru^III(NH₃)(bpy)₂]⁴⁺ for the oxidation of glucose was investigated by cyclic voltammetry. These ruthenium (III) complexes exhibit appropriate redox potentials of 0.131–0.09 V vs. SCE to act as electron‐transfer mediators. The plot of anodic current vs. the glucose concentration was linear in the concentration range between 2.52×10^?5 and 1.00×10^?4 mol L^?1. Moreover, the apparent Michaelis‐Menten kinetic (K_M^app) and the catalytic (K_cat) constants were 8.757×10^?6 mol L^?1 and 1,956 s^?1, respectively, demonstrating the efficiency of the ruthenium dinuclear oxo‐complex [(bpy)₂(NH₃)Ru^III(µ‐O)Ru^III(NH₃)(bpy)₂]⁴⁺ as mediator of redox electron‐transfer.     

Direct Electrochemistry of Hemoglobin Entrapped in Composite Electrodeposited Chitosan‐Multiwall Carbon Nanotubes and Nanogold Particles Membrane and Its Electrocatalytic Application

Hemoglobin was entrapped in composite electrodeposited chitosan‐multiwall carbon nanotubes (MCNTs) film by assembling gold nanoparticles and hemoglobin step by step. In phosphate buffer solution (pH 7), a pair of well‐defined and quasireversible redox peaks appeared with formal potential at ?0.289 V and peak separation of 100 mV. The redox peaks respected for the direct electrochemistry of hemoglobin at the surface of chitosan‐MCNTs‐gold nanoparticles modified electrode. The parameters of experiments have also been optimized. The composite electrode showed excellent electrocatalysis to peroxide hydrogen and oxygen, the peak current was linearly proportional to H₂O₂ concentration in the range from 1×10^?6 mol/L to 4.7×10^?4 mol/L with a detection limit of 5.0×10^?7 mol/L, and this biosensor exhibited high stability, good reproducibility and better selectivity. The biosensor showed a Michaelis–Menten kinetic response as H₂O₂ concentration is larger than 5.0×10^?4 mol/L, the apparent Michaelis–Menten constant for hydrogen peroxide was calculated to be 1.61 μmol/L.     

Fe3O4@SiO2‐PANI‐Au Nanocomposite Prepared for Electrochemical Determination of Quercetin in Food Samples and Biological Fluids

A new electrochemical sensor based on Fe₃O₄@SiO₂‐PANI‐Au nanocomposite was fabricated for modification of glassy carbon electrode (Fe₃O₄@SiO₂‐PANI‐Au GCE). The Fe₃O₄@SiO₂‐PANI‐Au nanocomposite was characterized by TEM, FESEM‐EDS‐Mapping, XRD, and TGA methods. The Fe₃O₄@SiO₂‐PANI‐Au GC electrode exhibited an acceptable sensitivity, fast electrochemical response, and good selectivity for determination of quercetin. Under optimal conditions, the linear range for quercetin concentrations using this sensor was 1.0×10^?8 to 1.5×10^?5 mol L^?1, and the limit of detection was 3.8×10^?9 mol L^?1. The results illustrated that the offered sensor could be a possible alternative for the measurement of quercetin in food samples and biological fluids.     

Voltammetric Sensor for Sodium Nitroprusside Determination in Biological Fluids Using Films of Poly‐L‐Lysine

Sodium nitroprusside (NP), a commercial vasodilator, can be pre‐concentrated on vitreous carbon electrode modified by films of 97.5%: 2.5% poly‐L ‐lysine (PLL): glutaraldehyde (GA). This coating gives acceptable anion exchange properties whilst giving the required improvement of adhesion to the glassy carbon electrode surface. Linear response range and detection limit on nitroprusside in B‐R buffer pH 4.0, were 1×10^?6 to 2×10^?5 mol L^?1 and 1×10^?7 mol L^?1, respectively. The repeatability of the proposed sensor, evaluated in term of relative standard deviation, was measured as 4.1% for 10 experiments. The voltammetric sensor was directly applied to determination of nitroprusside in human plasma and urine samples and the average recovery for these samples was around 95–97% without any pre treatment.     

Simultaneous Determination of Thallium and Lead on a Chemically Modified Electrode with Langmuir– Blodgett Film of a p‐tert‐Butylcalix[4]arene Derivative

A new voltammetric sensor, Langmuir–Blodgett (LB) film of a p‐tert‐butylcalix[4]arene derivative modified glassy carbon electrode, was designed and successfully used in simultaneous determination of Tl⁺ and Pb²⁺ by square‐wave anodic stripping voltammetry. Under the optimum experimental conditions, this newly developed sensor reveal good linear response for Tl⁺ and Pb²⁺ in the concentration range of 3×10^?8–4×10^?6 mol L^?1 and 2×10^?7–2×10^?5 mol L^?1 respectively. The detect limits are 2×10^?8 mol L^?1 for Tl⁺ and 8×10^?8 mol L^?1 for Pb²⁺. Using proposed method, Tl⁺ and Pb²⁺ in environment samples were determined with satisfactory results.     

Fullerene‐β‐Cyclodextrin Conjugate Based Electrochemical Sensing Device for Ultrasensitive Detection of p‐Nitrophenol

The article describes the use of a fullerene (C₆₀)‐β‐cyclodextrin conjugate, synthesized via 1,3‐dipolar cycloaddition, for the ultrasensitive electrochemical detection of p‐nitrophenol. This conjugate was successfully immobilized on the surface of a glassy carbon electrode and the developed device showed high activity towards p‐nitrophenol due to the synergetic effect of C₆₀, the latter becoming highly conductive upon reduction. The determination of p‐nitrophenol was performed by using square wave voltammetry over a concentration range from 2.8×10^?9 mol L^?1 to 4.2×10^?7 mol L^?1 and the detection limit was calculated to be 1.2×10^?9 mol L^?1.     

Electrochemical Determination of Neurotransmitters at Crown Ether Modified Carbon Nanotube Composite: Application for Sub‐nano‐sensing of Serotonin in Human Serum

We propose an electrochemical sensor based on applying two successive thin layers from a mixture of multiwalled carbon nanotubes‐ionic liquid crystal and crown ether at glassy carbon electrode surface (GC/(CNTs‐ILC)/Crown). The sensor was used for sensitive determination of neurotransmitters based on effective synergism between its components. The compact conducting surface of (CNTs ‐ ILC) with large surface area allowed the assembling of stable host‐guest inclusion complexes between crown ethers and neurotransmitters. The GC/(CNTs‐ILC)/Crown exhibited excellent electro‐catalytic activity toward the determination of serotonin (ST) in a wide linear dynamic range: 0.005 μmol L^?1 to 100 μmol L^?1. In the concentration range 0.005 μmol L^?1 to 1 μmol L^?1, the detection limit is 2.03×10^?10 mol L^?1 and quantification limit is 6.78×10^?10 mol L^?1 with correlation coefficient 0.999. The sensor was successfully applied for ST detection in human serum samples with satisfied recovery results. The sensor showed excellent analytical performance for the determination of ST in terms of low detection limit, good sensitivity and reproducibility. Furthermore excellent anti‐interference ability and simultaneous determination of ST in presence of other compounds as ascorbic acid, dopamine and antidepressant drug were achieved.     

Selective Electrochemical Determination of Dopamine with Molecularly Imprinted Poly(Carbazole‐co‐Aniline) Electrode Decorated with Gold Nanoparticles

Dopamine (DA) is a significant neurotransmitter in the central nervous system, coexisting with uric acid (UA) and ascorbic acid (AA). UA and AA are easily oxidizable compounds having potentials close to that of DA for electrochemical analysis, resulting in overlapping voltammetric response. In this work, a novel molecularly imprinted (MI) electrochemical sensor was proposed for selective determination of DA (in the presence of up to 80‐fold excess of UA and AA), relying on gold nanoparticles (Au_nano)‐decorated glassy carbon (GC) electrode coated with poly(carbazole (Cz)‐co‐aniline (ANI)) copolymer film incorporating DA as template (DA imprinted‐GC/P(Cz‐co‐ANI)‐Au_nano electrode, DA‐MIP‐Au_nano electrode). The DA recognizing sensor electrode showed great electroactivity for analyte oxidation in 0.2 mol L^?1 pH 7 phosphate buffer. Square wave voltammetry (SWV) was performed within 10^?4–10^?5 mol L^?1 of DA, of which the oxidation peak potential was observed at 0.16 V. The limit of detection (LOD) and limit of quantification (LOQ) were 2.0×10^?6 and 6.7×10^?6 mol L^?1, respectively. Binary and ternary synthetic mixtures of DA‐UA, DA‐AA and DA‐UA‐AA yielded excellent recoveries for DA. Additionally, DA was quantitatively recovered from a real sample of bovine serum spiked with DA, and determined in concentrated dopamine injection solution. The developed SWV method was statistically validated against a literature potentiodynamic method using a caffeic acid modified‐GC electrode.     

Two‐Color Valence‐to‐Core X‐ray Emission Spectroscopy Tracks Cofactor Protonation State in a Class I Ribonucleotide Reductase

Proton transfer reactions are of central importance to a wide variety of biochemical processes, though determining proton location and monitoring proton transfers in biological systems is often extremely challenging. Herein, we use two‐color valence‐to‐core X‐ray emission spectroscopy (VtC XES) to identify protonation events across three oxidation states of the O₂‐activating, radical‐initiating manganese–iron heterodinuclear cofactor in a class I‐c ribonucleotide reductase. This is the first application of VtC XES to an enzyme intermediate and the first simultaneous measurement of two‐color VtC spectra. In contrast to more conventional methods of assessing protonation state, VtC XES is a more direct probe applicable to a wide range of metalloenzyme systems. These data, coupled to insight provided by DFT calculations, allow the inorganic cores of the Mn^IVFe^IV and Mn^IVFe^III states of the enzyme to be assigned as Mn^IV(μ‐O)₂Fe^IV and Mn^IV(μ‐O)(μ‐OH)Fe^III, respectively.     

Graphene‐Nafion Composite Film Modified Electrode for Voltammetric Sensor for Determination of Dihydromyricetin

A simple but highly snesitive electrochemical sensor for the determination of dihydromyricetin (DMY) based on graphene‐Nafion nanocomposite film modified Glassy carbon electrode (GCE) was reported. The characteristic of the sensor was examined by scanning electron microscopic (SEM) and electrochemical impedance spectroscopy (EIS). Compares with bare GCE, pre‐anodized glassy carbon electrode (GCE(ox)) and Nafion modified electrode, the sensor exhibited the more superior ability of detecting DMY, due to the synergetic graphene and Nafion. Other, the dependence of the current on pH, instrumental parameters, accumulation time and potential were investigated to optimize the experimental conditions in the determination of DMY. Under the selected conditions, the response peak currents were linear relationship with the DMY concentrations in the range of 8.0 × 10^?8 ～ 2.0 × 10^?5 mol L^?1 with a detection limit of 2.0 × 10^?8 mol L^?1. And, the method was also applied successfully to detect DMY in Ampelopsis grossedentata samples.     

A new voltammetric sensor for the determination of sulfite in water and wastewater using modified-multiwall carbon nanotubes paste electrode

The electrochemical response of a modified-carbon nanotubes paste electrode with p-aminophenol was investigated as an electrochemical sensor for sulfite determination. The electrochemical behaviour of sulfite was studied at the surface of the modified electrode in aqueous media using cyclic voltammetry and square wave voltammetry. It has been found that under the optimum condition (pH 7.0) in cyclic voltammetry, the oxidation of sulfite occurs at a potential about 680?mV less positive than that of an unmodified-carbon nanotubes paste electrode. Under the optimized conditions, the electrocatalytic peak current showed linear relationship with sulfite concentration in the range of 2.0?×?10^?7–2.8?×?10^?4?mol?L^?1 with a detection limit of 9.0?×?10^?8?mol?L^?1 sulfite. The relative standard deviations for ten successive assays of 1.0 and 50.0?µmol?L^?1 sulfite were 2.5% and 2.1%, respectively. Finally, the modified electrode was examined as a selective, simple and precise new electrochemical sensor for the determination of sulfite in water and wastewater samples.     

Electrochemical Behavior of 8‐Azaguanine at DNA Langmuir–Blodgett Modified Glassy Carbon Electrode and Its Analytical Application

A highly sensitive electrochemical biosensor for the detection of trace amounts of 8‐azaguanine has been designed. Double stranded (ds)DNA molecules are immobilized onto a glassy carbon electrode surface with Langmuir–Blodgett technique. The adsorptive voltammetric behaviors of 8‐azaguanine at DNA‐modified electrode were explored by means of cyclic voltammetry and square wave voltammetry. Compared with bare glassy carbon electrode (GCE), the Langmuir–Blodgett film modified electrode can greatly improve the measuring sensitivity of 8‐azaguanine. Under the optimum experimental conditions, the Langmuir–Blodgett film modified electrode in pH 3.0 Britton–Robinson buffer solutions shows a linear voltammetric response in the range of 5.0×10^?8 to 1.0×10^?5 mol L^?1 with detection limit 9.0×10^?9 mol L^?1. The method proposed was applied successfully for the determination of 8‐azaguanine in diluted human urine with wonderful satisfactory.     

Copper‐based Metal‐organic Framework Applied in the Development of an Electrochemical Biomimetic Sensor for Catechol Determination

In this study, the synthesis and characterization of a Cu‐based metal‐organic framework (MOF) [Cu₃(BTC)₂(H₂O)₃]_n (where BTC=benzene‐1,3,5‐tricarboxylate), known as HKUST‐1, were performed. The Cu‐MOF was applied in the modification of a carbon paste to obtain a biomimetic sensor for the electrochemical determination of catechol. Kinetic assays confirmed that the Cu‐MOF acts as a catalyst for the oxidation of catechol and it can be considered as a catechol oxidase mimetic. Under optimized conditions, the calibration curve for catechol presented a linear range of 8.0×10⁻⁷ to 3.2×10⁻⁵ mol L⁻¹, with detection limit of=1.0×10⁻⁷ mol L⁻¹. The sensor demonstrated good intra‐day repeatability and inter‐electrode reproducibility (relative standard deviations of 3.8 % (n=10) and 4.3 % (n=6), respectively). In the selectivity study, an adequate peak‐to‐peak separation was observed for hydroquinone and uric acid in relation to catechol, demonstrating that this sensor has the potential for use in the simultaneous determination of these compounds. This sensor was successfully applied in the determination of catechol in water samples.     

Determination of Rutin in Green Tea Infusions Using Square‐Wave Voltammetry with a Rigid Carbon‐Polyurethane Composite Electrode

This paper presents a comparative study on the electrochemical behavior of the flavonoid rutin on a rigid carbon‐polyurethane composite electrode and on a glassy carbon electrode. The electrochemical oxidation reaction of rutin was found to be quasireversible and affected by adsorption on the electrode surface. A square‐wave voltammetric method was developed for determination of rutin in green tea infusion samples using the RCPE electrode and data treatment by a deconvolution procedure. The detection limit achieved in buffered solutions was 7.1×10^?9 mol L^?1 using the RCPE and 1.7×10^?8 mol L^?1 using the GC electrode the average reproducibility for five determinations being 3.5%.