Spectral measurements of incipient plasma temperature and electron number density during laser ablation of aluminum in air

Plasmas generated during incipient laser ablation of aluminum in air were studied using emission spectroscopy. A plasma emission model was developed, invoking one-dimensional radiative transfer, to describe the observed emission spectra, while taking into account the effects of continuum radiation. Theoretical spectra were calculated and compared to experimental spectra in the range 387–406 nm. Satisfactory agreement was found between the experimental and predicted spectra, especially at delay times of 30–200 ns, thus providing plasma temperatures and electron number densities as functions of delay time and laser irradiance (1.8–8.0 GW/cm²). In general, both the plasma temperature and electron number density rise at greater laser irradiances but drop at increasing delay times, with a more rapid drop for delay times less than 60 ns. PACS 42.62.Fi; 52.25.-b     

Titanium plasma spectroscopy studies under double pulse laser excitation

Laser-induced breakdown spectroscopy (LIBS) was applied for parametric studies of titanium (Ti) plasma using single and double pulsed laser excitation scheme. Here a pulsed Nd:YAG laser was employed for generation of laser produced plasma from solid Ti target at ambient pressure. Several ionized titanium lines were recorded in the 312–334 nm UV region. The temporal evolution of plasma parameters such as excitation temperature and electron number density was evaluated. The effect of incident laser irradiance, position of the laser beam focal point with respect to the surface of illumination, single and double laser pulse effect on plasma parameters were also investigated. This study contributes to a better understanding of the LIBS plasma dynamics of the double laser pulse effect on the temporal evolution of various Ti emission lines, the detection sensitivity and the optimal dynamics of plasma for ionized states of Ti. The results demonstrate a faster decay of the continuum and spectral lines and a shorter plasma life time for the double pulse excitation scheme as compared with single laser pulse excitation. For double pulse excitation technique, the emissions of Ti lines intensities are enhanced by a factor of five which could help in the improvement of analytical performance of LIBS technique. In addition, this study proved that to avoid inhomogeneous effects in the laser produced plasma under high laser intensities, short delay times between the incident laser pulse and ICCD gate are required.     

激光诱导Ti等离子体光谱的时间演化特性研究

利用Nd:YAG激光器产生的1064 nm、10 ns脉冲激光聚焦在空气中的Ti靶,观测了激光诱导Ti等离子体发射光谱.调节激光能量为45 mJ/pulse,分析了时间范围在0到4000 ns的时间分辨发射光谱和谱线轮廓以及展宽.在局部热力学平衡(LTE)条件下,利用Saha-boltzmann图法拟合电子温度,Saha方程计算电子密度,讨论了等离子体电子温度和电子密度随时间的演化规律.结果表明,在所讨论的时间范围内,谱线的强度在延时250 ns处达到最大,250 ns后随着延迟时间的增加减小,电子密度和电子温度在延时1000 ns内快速衰减,1000 ns后衰减速度变慢.     

Forward plasma emission through laser–foil interaction with nanosecond lasers

Fundamental investigations of plasma diagnostics of a forward laser plasma acceleration employing laser–foil interactions were conducted for an Al-foil target irradiated with an Nd:YAG laser of 1 J/pulse with pulse width of 10 ns. Temporal evolutions of electron temperatures and densities were evaluated with electrostatic probes and spectroscopic diagnostics. From the results, it was shown that an average speed of ions in a forward direction was about 40 km/s. Also, it was shown that the plasma temperature and density were about 2.5–8 eV and 10¹⁰ cm⁻³, respectively.     

Optical absorption in early stage low temperature laser produced plasma

We describe a new technique to measure the UV/visible absorption spectrum of the ablated material during the laser pulse. The technique utilizes the continuum emission from one laser produced plasma as a light source to measure the absorption properties of a second laser produced plasma which is formed on a semi-transparent target with an array of 40 μm holes. A 6 ns, 1064 nm laser was used to ablate a Ag target and the plasma absorption was measured in the range 450–625 nm for a laser fluence of 1 J cm⁻². The total absorption cross-section is (0.5–1.5)×10⁻¹⁷ cm² in the range 450–540 nm. By comparing the measured absorption with a calculation using the plasma spectroscopy code FLYCHK it can be concluded that, in the wavelength region examined here, the absorption is mainly due to bound-bound transitions.     

Laser absorption and fluorescence diagnostics of a plasma

Diagnostics of a near-surface laser plasma, the plasma of a strong-current pulse gaseous discharge in inert gases, nitrogen, and carbon dioxide under conditions of intense evaporation of the wall of the discharge chamber, the plasma of a discharge with a hollow cathode, and the active medium of an excimer laser was conducted by methods of intracavity laser spectroscopy and laser-induced fluorescence. The dynamic fields and absolute concentrations of atoms, ions, molecules and electrons, the plasma temperature, and the velocities of flows of particles were measured. The quantitative determination of the density of particles in the erosion laser flame prior to breakdown and the phenomena associated with the formation of molecules in the laser plasma received primary consideration. To whom correspondence should be addressd. Instite of Molecular and Atomic Physics of the Academy of Sciences of Belarus, 70, F. Skorina Ave., Minsk, 220072, Belarus. Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 3, pp. 281–290, May–June, 1997.     

Effect of ZnO plasma plume dynamics on laser ablation

The dynamic behaviors and optical properties of a ZnO plasma plume produced by pulsed laser ablation using a Nd:YAG laser (wavelength: 532 nm, pulse width: 3 ns) were studied by fast photography using a commercial gated charge coupled device (CCD) camera linked with a delay circuit and by optical emission spectroscopy at various ambient oxygen pressures. Fast photography was conducted with a resolving power of 0.25 μs and the expansion behaviors of the laser ablation plume were observed. Plasma plume expansion velocity decreased with oxygen partial pressure. The flow of the plasma plume in the early stage of expansion of up to 3 ms agreed well with the drag model.     

脉冲CO2激光烧蚀锡靶等离子体的数值研究

使用一维辐射流体力学程序MULTI模拟了脉冲CO2激光烧蚀平面锡靶的过程,研究了脉冲宽度、峰值功率密度、靶材初始密度对锡等离子体电子密度、电子温度的时空分布的影响,并结合统计分析得到最有利于产生13.5 nm 极紫外光的激光脉冲宽度。模拟结果表明,脉冲宽度为100~200 ns的长脉冲激光产生的等离子体有利于实现极紫外输出的最佳条件,通过分析等离子体的电子密度、电子温度的分布对这一结论进行了解释。临界电子密度区域有效吸收了脉冲能量,而低密度的羽辉对激光与极紫外辐射的吸收很少。采用长脉冲激光,使得辐射极紫外等离子体持续时间更长,是提高极紫外辐射效率的有效手段。同时模拟还发现,靶材初始密度对等离子体参数的影响不大。     

Experimental investigation of ablation efficiency and plasma expansion during femtosecond and nanosecond laser ablation of silicon

Femtosecond laser (Ti:sapphire, 100 fs pulse duration) ablation of silicon in air was compared with nanosecond laser (Nd:YAG, 3 ns pulse duration) ablation at ultraviolet wavelength (266 nm). Laser ablation efficiency was studied by measuring crater depth as a function of pulse number. For the same number of laser pulses, the fs-ablated crater was about two times deeper than the ns-crater. The temperature and electron number density of the laser-induced plasma were determined from spectroscopic measurements. The electron number density and temperature of fs-induced plasmas decreased faster than ns-induced plasmas due to different energy deposition mechanisms. Images of the laser-induced plasma were obtained with femtosecond time-resolved laser shadowgraph imaging. Plasma expansion in both the perpendicular and the lateral directions were compared. PACS 52.38.Mf; 52.30.-q     

Temporal follow up of the LTE conditions in aluminum laser induced plasma at different laser energies

In order to analyze the emission spectrum of a laser-induced plasma for obtaining quantitative information on the abundance of the species present in the plasma it is necessary to study the local thermodynamic equilibrium (LTE) conditions in the plasma and determine the best conditions at which they are satisfied. In the present work Nd:YAG laser light pulses (λ=?1064 nm, 6 ns) of different energies (25, 50, 75 and 100 mJ) are focused using a quartz lens (focal length 10 cm) onto certified aluminum alloy samples in air under atmospheric pressure. The emitted spectra are collected and analyzed using an echelle spectrometer coupled with an intensified charge coupled device camera. The temporal history of the plasma is obtained by recording the emission features at predetermined delays and at a fixed gate width (2500 ns). For each spectrum both electron density and excitation temperature are calculated for each delay time and laser pulse energy; we found that the values of the electron density are decreasing from 10¹⁸ to 10¹⁷ cm^-3. The corresponding excitation temperatures were between 30000 and 4000 K depending on the laser pulse energy and the sample used. The LTE conditions were followed up for the different delays and different energies to determine the temporal range in which they are satisfied. It has been found that in the cases of 25- and 50-mJ laser energies, the LTE conditions were satisfied in the chosen delay range (500–5000 ns). On the other hand, for higher laser energies, the LTE conditions were critical at delay times less than 1500 ns and are satisfied for longer delays.     

Plasma plume induced during laser ablation of graphite

The plasma plume induced during ArF laser ablation of a graphite target is studied. Velocities of the plasma expansion front are determined by the optical time of flight method. Mass center velocities of the emitting atoms and ions are constant and amount to 1.7×10⁴ and 3.8×10⁴ m s⁻¹, respectively. Higher velocities of ions result probably from their acceleration in electrostatic field created by electron emission prior to ion emission. The emission spectroscopy of the plasma plume is used to determine the electron densities and temperatures at various distances from the target. The electron density is determined from the Stark broadening of the Ca II and Ca I lines. It reaches a maximum of ∼9.5×10²³ m⁻³ 30 ns from the beginning of the laser pulse at the distance of 1.2 mm from the target and next decreases to ∼1.2×10²² m⁻³ at the distance of 7.6 mm from the target. The electron temperature is determined from the ratio of intensities of ionic and atomic lines. Close to the target the electron temperature of ∼30 kK is found but it decreases quickly to 11.5 kK 4 mm from the target.     

Neutral molybdenum atom and dimer formations in laser-induced plasma: emission study of 355-nm pulse laser photolysis of Mo(CO)6 in the gas phase

6 in the gas phase at room temperature. The transient behavior of emissive atoms and dimers were measured by using a time-resolved UV-vis emission spectroscopy. Most atomic emissions were found to consist of two distinct transient components, an “early” component with a similar time profile to the photolysis pulse, and a “late” component with a peak at around 300 ns after the photolysis. The fact that the addition of an electron scavenger decreased the late emission sensibly suggests that the late emission was caused by Mo^* produced in a neutralization process of ionic species. A plausible mechanism involving electron–ion recombination was proposed for the late emission and examined by the numerical simulation of the transient behaviors as a function of some experimental parameters such as total pressure, initial ion concentration, and electron scavenger concentration. Received: 9 April 1997/Revised version: 12 June 1997     

激光辐照固体靶产生等离子体反冲研究

提出一种通过诊断等离子体反冲动量来计算激光加载产生冲击压强的方法. 当强激光辐照固体靶表面时, 所产生的高速喷射的等离子体对靶具有反冲作用, 通过诊断等离子体反冲动量的变化可以计算激光辐照固体靶产生的冲击压强变化. 本文利用辐射流体力学软件研究了这种诊断方法, 模拟采用的激光功率密度为5×10¹²-5×10¹³ W/cm², 激光脉宽选取纳秒量级. 模拟结果表明该方法是有效且可行的.     

Effects of pulse energy ratios on plasma characteristics of dual-pulse fiber-optic laser-induced breakdown spectroscopy

Laser-induced plasmas of dual-pulse fiber-optic laser-induced breakdown spectroscopy with different pulse energy ratios are studied by using the optical emission spectroscopy(OES)and fast imaging.The energy of the two laser pulses is independently adjusted within 0–30 m J with the total energy fixed at 30 m J.The inter-pulse delay remains 450 ns constantly.As the energy share of the first pulse increases,a similar bimodal variation trend of line intensities is observed.The two peaks are obtained at the point where the first pulse is half or twice of the second one,and the maximum spectral enhancement is at the first peak.The bimodal variation trend is induced by the change in the dominated mechanism of dual-pulse excitation with the trough between the two peaks caused by the weak coupling between the two mechanisms.By increasing the first pulse energy,there is a transition from the ablation enhancement dominance near the first peak to the plasma reheating dominance near the second peak.The calculations of plasma temperature and electron number density are consistent with the bimodal trend,which have the values of 17024.47 K,2.75×10¹⁷cm;and 12215.93 K,1.17×10¹⁷cm;at a time delay of 550 ns.In addition,the difference between the two peaks decreases with time delay.With the increase in the first pulse energy share,the plasma morphology undergoes a transformation from hemispherical to shiny-dot and to oblate-cylinder structure during the second laser irradiation from the recorded images by using an intensified charge-coupled device(ICCD)camera.Correspondingly,the peak expansion distance of the plasma front first decreases significantly from 1.99 mm in the single-pulse case to 1.34 mm at 12/18(dominated by ablation enhancement)and then increases slightly with increasing the plasma reheating effect.The variations in plasma dynamics verify that the change of pulse energy ratios leads to a transformation in the dual-pulse excitation mechanism.     

Spectroscopic studies of sodium nitrate plasma produced by nanosecond laser ablation

We present the optical emission characteristics of the sodium plasma produced at the surface of sodium nitrate (NaNO₃) also known as Chile saltpeter. We used a Q-switched Nd:YAG (Quantel Brilliant) pulsed laser having a pulse duration of 5?ns and 10?Hz repetition rate which is capable of delivering 400?mJ at 1064?nm and 200?mJ at 532?nm. The target material was placed in front of laser beam in air (atmospheric pressure). The experimentally observed line profiles of neutral sodium have been used to extract the electron temperature using the Boltzmann plot method, whereas the electron number density has been determined from the Stark broadening. The electron temperature is calculated by varying the distance from the target surface along the line of propagation of the plasma plume and also by varying the laser irradiance. Besides, we have studied the variation of number density as a function of laser irradiance as well as its variation with the distance from the target surface. It is observed that electron temperature and electron number density increase as the laser irradiance is increased.     

Quantitative studies of copper plasma using laser induced breakdown spectroscopy

In the present work, we present the spatial evolution of the copper plasma produced by the fundamental harmonic (1064 nm) and second harmonic (532 nm) of a Q-switched Nd:YAG laser. The experimentally observed line profiles of neutral copper have been used to extract the electron temperature using the Boltzmann plot method, whereas, the electron number density has been determined from the Stark broadening. Besides we have studied the variation of electron temperature and electron number density as a function of laser energy at atmospheric pressure. The Cu I lines at 333.78, 406.26, 465.11 and 515.32 nm are used for the determination of electron temperature. The relative uncertainty in the determination of electron temperature is ≈10%. The electron temperature calculated for the fundamental harmonic (1064 nm) of Nd:YAG laser is 10500–15600 K, and that for the second harmonic (532 nm) of Nd:YAG laser is 11500–14700 K at a Q Switch delay of 40 μs. The electron temperature has also been calculated as a function of laser energy from the target surface for both modes of the laser. We have also studied the spatial behavior of the electron number density in the plume. The electron number densities close to the target surface (0.05 mm), in the case of fundamental harmonic (1064 nm) of Nd:YAG laser having pulse energy 135 mJ and second harmonic (532 nm) of Nd:YAG laser with pulse energy 80 mJ are 2.50×10¹⁶ and 2.60×10¹⁶ cm⁻³, respectively.     

Microwave energy channeling in plasma waveguides created by a high-power UV laser in the atmosphere

The grazing mode of microwave propagation in a hollow plasma waveguide formed by ionization of atmospheric air with a small easily ionized additive by strong UV pulses of the Garpun KrF laser (λ = 248 nm, the pulse duration and energy are ∼70 ns and ∼50 J) was experimentally demonstrated for the first time. The annular laser beam produced a hollow tube ∼10 cm in diameter with an electron density of ∼10¹² cm⁻³ in a plasma wall ∼1 cm thick, over whichmicrowave radiation with λ _mw ∼ 8 mm was transmitted to a distance of 60 m. Themicrowave signal transmitted by the waveguide was amplified by a factor of 6 in comparison with propagation in free space.     

Recombination emissions and spectral blueshift of pump radiation from ultrafast laser induced plasma in a planar water microjet

We report spectroscopic investigations of an ultrafast laser induced plasma generated in a planar water microjet. Plasma recombination emissions along with the spectral blueshift and broadening of the pump laser pulse contribute to the total emission. The laser pulses are of 100 fs duration, and the incident intensity is around 10¹⁵ W/cm². The dominant mechanisms leading to plasma formation are optical tunnel ionization and collisional ionization. Spectrally resolved polarization measurements show that the high frequency region of the emission is unpolarized whereas the low frequency region is polarized. Results indicate that at lower input intensities the emission arises mainly from plasma recombinations, which is accompanied by a weak blueshift of the incident laser pulse. At higher input intensities strong recombination emissions are seen, along with a broadening and asymmetric spectral blueshift of the pump laser pulse. From the nature of the blueshifted laser pulse it is possible to deduce whether the rate of change of free electron density is a constant or variable within the pulse lifetime. Two input laser intensity regimes, in which collisional and tunnel ionizations are dominant respectively, have been thus identified.     

Spectral and ion emission features of laser-produced Sn and SnO_2 plasmas

We have made a detailed comparison of the atomic and ionic debris, as well as the emission features of Sn and SnO_2 plasmas under identical experimental conditions. Planar slabs of pure metal Sn and ceramic SnO_2 are irradiated with1.06 μm, 8 ns Nd:YAG laser pulses. Fast photography employing an intensified charge coupled device(ICCD), optical emission spectroscopy(OES), and optical time of flight emission spectroscopy are used as diagnostic tools. Our results show that the Sn plasma provides a higher extreme ultraviolet(EUV) conversion efficiency(CE) than the Sn O2 plasma.However, the kinetic energies of Sn ions are relatively low compared with those of SnO_2. OES studies show that the Sn plasma parameters(electron temperature and density) are lower compared to those of the SnO_2 plasma. Furthermore, we also give the effects of the vacuum degree and the laser pulse energy on the plasma parameters.     

飞秒激光成丝诱导Cu等离子体的温度和电子密度

研究了飞秒激光成丝诱导铜击穿光谱,利用光发射光谱对产生的铜等离子体光谱强度沿着丝长度进行了测量,获得了在不同样品与聚焦透镜间距离的Cu(I)的强度分布.结果显示,由于强度钳箍效应成丝诱导的光谱在较大的透镜样品间距离范围内有较强的辐射强度.另外,利用玻尔兹曼图和斯塔克展宽计算了整个成丝繁衍距离中Cu等离子体温度和电子密度.