几种手性醇在纤维素键合的SBA-15基手性固定相上的直接拆分

在强酸性条件下, 以三嵌段聚醚P123为模板, 合成了孔径大且粒径均匀的SBA-15介孔二氧化硅微球. 将含有少量三乙氧硅丙基氨基甲酸酯残基的纤维素-三(3,5-二甲基苯基氨基甲酸酯)通过分子间缩聚作用固载到氨丙基化的SBA-15微球上, 制得手性固定相; 采用常规和非常规的流动相模式, 对一些芳香醇的消旋体进行了手性拆分. 实验结果表明, 所制备的SBA-15微球不仅分散性良好, 具有规则的二维六方孔道结构, 而且消除了微孔; 所制备的键合手性固定相不仅固载手性选择剂的量大, 而且经六甲基二硅胺烷封端后可有效改善拖尾现象, 对实验选用的手性醇具有较高的拆分能力; 与大孔硅胶为基质的同类纤维素键合手性固定相相比, 该固定相对同种手性消旋体的分离因子明显提高.     

Facile method to synthesize platelet SBA-15 silica with highly ordered large mesopores

Highly ordered mesoporous SBA-15 silica with large pore diameter of 18 nm (nominal BJH pore diameter ~22 nm) and short pore length (~500 nm) was synthesized using a micelle expander 1,3,5-triisopropylbenzene in the absence of ammonium fluoride by employing short initial stirring time at 17 °C followed by static aging at low temperature. Scanning and transmission electron microscopies revealed that the material comprised of platelet particles in which large mesopores were nearly flawlessly arranged within uniform domains up to 3 μm in size. The platelet SBA-15 had the (100) interplanar spacing of 17 nm, high surface area (~470 m(2) g(-1)) and large pore volume (~1.6 cm(3) g(-1)). The hydrothermal treatment at 130 °C for 2 days was employed to eliminate constrictions from the pore channels. The control experiment showed that a sample prepared with prolonged stirring had very similar mesoporous properties, but the particle size was smaller and the domains were irregular, proving that the static conditions facilitate the formation of SBA-15 with platelet particle morphology. The absence of ammonium fluoride was also critical in attaining the platelet particle shape.     

High-surface-area catalyst design: Synthesis, characterization, and reaction studies of platinum nanoparticles in mesoporous SBA-15 silica

Platinum nanoparticles in the size range of 1.7-7.1 nm were produced by alcohol reduction methods. A polymer (poly(vinylpyrrolidone), PVP) was used to stabilize the particles by capping them in aqueous solution. The particles were characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). TEM investigations demonstrate that the particles have a narrow size distribution. Mesoporous SBA-15 silica with 9-nm pores was synthesized by a hydrothermal process and used as a catalyst support. After incorporation into mesoporous SBA-15 silica using low-power sonication, the catalysts were calcined to remove the stabilizing polymer from the nanoparticle surface and reduced by H2. Pt particle sizes determined from selective gas adsorption measurements are larger than those determined by bulk techniques such as XRD and TEM. Room-temperature ethylene hydrogenation was chosen as a model reaction to probe the activity of the Pt/SBA-15 materials. The reaction was shown to be structure insensitive over a series of Pt/SBA-15 materials with particle sizes between 1.7 and 3.6 nm. The hydrogenolysis of ethane on Pt particles from 1.7 to 7.1 nm was weakly structure sensitive with smaller particles demonstrating higher specific activity. Turnover rates for ethane hydrogenolysis increased monotonically with increasing metal dispersion, suggesting that coordinatively unsaturated metal atoms present in small particles are more active for C2H6 hydrogenolysis than the low index planes that dominate in large particles. An explanation for the structure sensitivity is suggested, and the potential applications of these novel supported nanocatalysts for further studies of structure-activity and structure-selectivity relationships are discussed.     

Large-pore mesoporous SBA-15 silica particles with submicrometer size as stationary phases for high-speed CEC separation

A new mesoporous sphere-like SBA-15 silica was synthesized and evaluated in terms of its suitability as stationary phases for CEC. The unique and attractive properties of the silica particle are its submicrometer particle size of 400 nm and highly ordered cylindrical mesopores with uniform pore size of 12 nm running along the same direction. The bare silica particles with submicrometer size have been successfully employed for the normal-phase electrochromatographic separation of polar compounds with high efficiency (e.g., 210,000 for thiourea), which is matched well with its submicrometer particle size. The Van Deemeter plot showed the hindrance to mass transfer because of the existence of pore structure. The lowest plate height of 2.0 microm was obtained at the linear velocity of 1.1 mm/s. On the other hand, because of the relatively high linear velocity (e.g., 4.0 mm/s) can be generated, high-speed separation of neutral compounds, anilines, and basic pharmaceuticals in CEC with C18-modified SBA-15 silica as stationary phases was achieved within 36, 60, and 34 s, respectively.     

Hydrothermal growth of mesoporous SBA-15 silica in the presence of PVP-stabilized Pt nanoparticles: synthesis, characterization, and catalytic properties

A novel high surface area heterogeneous catalyst based on solution phase colloidal nanoparticle chemistry has been developed. Monodisperse platinum nanoparticles of 1.7-7.1 nm have been synthesized by alcohol reduction methods and incorporated into mesoporous SBA-15 silica during hydrothermal synthesis. Characterization of the Pt/SBA-15 catalysts suggests that Pt particles are located within the surfactant micelles during silica formation leading to their dispersion throughout the silica structure. After removal of the templating polymer from the nanoparticle surface, Pt particle sizes were determined from monolayer gas adsorption measurements. Infrared studies of CO adsorption revealed that CO exclusively adsorbs to atop sites and red-shifts as the particle size decreases suggesting surface roughness increases with decreasing particle size. Ethylene hydrogenation rates were invariant with particle size and consistent with a clean Pt surface. Ethane hydrogenolysis displayed significant structure sensitivity over the size range of 1-7 nm, while the apparent activation energy increased linearly up to a Pt particle size of approximately 4 nm and then remained constant. The observed rate dependence with particle size is attributed to a higher reactivity of coordinatively unsaturated surface atoms in small particles compared to low-index surface atoms prevalent in large particles. The most reactive of these unsaturated surface atoms are responsible for ethane decomposition to surface carbon. The ability to design catalytic structures with tunable properties by rational synthetic methods is a major advance in the field of catalyst synthesis and for the development of accurate structure-function relationships in heterogeneous reaction kinetics.     

Effects of Morphology and Structural Characteristics of Ordered SBA-15 Mesoporous Silica on Release of Ibuprofen

Three kinds of highly ordered SBA-15 mesoporous materials with different pore sizes and morphologies denoted as LPS-SBA-15 (stick-like with pore size 7.28 nm), CPS-SBA-15 (stick-like with pore size 5.96 nm) and T-SBA-15 (tablet-like with pore size 4.64 nm) have been prepared, characterized and employed as carrier materials. The release behaviors of the ibuprofen in a simulated body fluid from these mesoporous silica materials were studied. The influences of pore size and exterior morphologies of mesoporous silica on the release behaviors of ibuprofen have been investigated. It has been found that the release becomes fast with increasing of pore size and slow with extending of transport pathway, and that the release rate of ibuprofen from the three kinds of SBA-15 is LPS-SBA-15 > T-SBA-15 > CPS-SBA-15. The results show that the inner structure as well as the exterior morphologies of SBA-15 mesoporous silica can seriously affect the release behaviors of ibuprofen.     

Ag/SBA-15复合材料的制备及其抗菌性质

本文采用二维六方结构的介孔硅SBA-15作为主体, 先将其浸渍在葡萄糖溶液中, 利用土伦试剂在原位发生氧化-还原反应, 成功地在介孔孔道中制备出分散的银纳米粒子, 并以金黄葡萄球菌为研究对象, 对Ag/SBA-15的抑菌性能及持续抑菌能力进行了检测, 结果表明, 样品对金黄葡萄球菌有明显的抑菌作用并具有持续的抑菌能力.     

Shape- and size-controlled synthesis in hard templates: sophisticated chemical reduction for mesoporous monocrystalline platinum nanoparticles

Here we report a novel hard-templating strategy for the synthesis of mesoporous monocrystalline Pt nanoparticles (NPs) with uniform shapes and sizes. Mesoporous Pt NPs were successfully prepared through controlled chemical reduction using ascorbic acid by employing 3D bicontinuous mesoporous silica (KIT-6) and 2D mesoporous silica (SBA-15) as a hard template. The particle size could be controlled by changing the reduction time. Interestingly, the Pt replicas prepared from KIT-6 showed polyhedral morphology. The single crystallinity of the Pt fcc structure coherently extended over the whole particle.     

Preparation of ordered mesoporous SiC from preceramic polymer templated by nanoporous silica

Highly ordered mesoporous SiC materials were prepared by infiltrating viscous liquid preceramic polymer, allylhydridopolycarbosilane, into two types of surface modified nanoporous silica templates: mesoporous silica SBA-15 and mesocellular siliceous foam. The silica templates were subsequently etched off after pyrolysis at 1000 degrees C under nitrogen atmosphere with the resultant formation of ordered mesoporous structures. The mesoporous SiC materials, synthesized from both types of templates possessed high Brunauer-Emmett-Teller (BET) surface areas in the range of 250-260 m(2)/g with pore sizes of 3.4-3.6 nm. The ordered structures of mesoporous SiC were exact inverse replicas of their respective silica templates, as characterized by small angle X-ray diffraction (XRD), transmission electron microscope (TEM) images, and the adsorption-desorption isotherm of nitrogen.     

介孔分子筛SBA-15作为高效液相色谱固定相分离维生素E

以三嵌段共聚物P123聚环氧乙烷-聚环氧丙烷-聚环氧乙烷(PEO-PPO-PEO)为模板,在强酸性(1.6mol/L HCl)条件下,水热合成了棒状二维六方有序介孔材料SBA-15.粒径棒长约1～1.5μm,直径为400～500nm,平均孔径5.8nm,BET比表面积799㎡/g.并用合成的SBA-15作为正相高效液相...     

Influence of the pore structure of MCM-41 and SBA-15 silica fibers on atomic layer chemical vapor deposition of cobalt carbonyl

Mesoporous high surface area MCM-41 and SBA-15 type silica materials with fibrous morphology were synthesized and used as support materials for the ALCVD (atomic layer chemical vapor deposition) preparation of Co/MCM-41 and Co/SBA-15 catalysts. Co/MCM-41 and Co/SBA-15 catalysts were prepared by deposition of Co2(CO)8 from the gas phase onto the surfaces of preheated support materials in a fluidized bed reactor. For both silica materials, two different kinds of preparation methods, direct deposition and a pulse deposition method, were used. Pure silica supports as well as supported cobalt catalysts were characterized by various spectroscopic (IR) and analytical (X-ray diffraction, Brunauer-Emmett-Teller, elemental analysis) methods. MCM-41 and SBA-15 fibers showed considerable ability to adsorb Co2(CO)8 from the gas phase. For MCM-41 and SBA-15 silicas, cobalt loadings of 13.7 and 12.1 wt % were obtained using the direct deposition method. The cobalt loadings increased to 23.0 and 20.7 wt % for MCM-41 and SBA-15 silicas, respectively, when the pulse deposition method was used. The reduction behavior of silica-supported cobalt catalysts was found to depend on the catalyst preparation method and on the mesoporous structure of the support material. Almost identical reduction properties of SBA-15-supported catalysts prepared by different deposition methods are explained by the structural properties of the mesoporous support and, in particular, by the chemical structure of the inner surfaces and walls of the mesopores. Pulse O2/H2 chemisorption experiments showed catalytically promising redox properties and surface stability of the prepared MCM-41- and SBA-15-supported cobalt catalysts.     

Direct synthesis and catalytic applications of ordered large pore aminopropyl-functionalized SBA-15 mesoporous materials

SBA-15 mesoporous silica has been functionalized with aminopropyl groups through a simple co-condensation approach of tetraethyl orthosilicate (TEOS) and (3-aminopropyl)triethoxysilane (APTES) using amphiphilic block copolymers under acidic conditions. The organic-modified SBA-15 materials have hexagonal crystallographic order, pore diameter up to 60 A, and the content of aminopropyl groups up to 2.3 mmol g(-1). The influences of TEOS prehydrolysis period and APTES concentration on the crystallographic order, pore size, surface area, and pore volume were examined. TEOS prehydrolysis prior to the addition of APTES was found essential to obtain well-ordered mesoporous materials with amino functionality. The amount of APTES incorporated in the silica framework increased with the APTES concentration in the synthesis gel, while the ordering of the mesoporous structure gradually decreased. Analysis with TG, IR, and solid state NMR spectra demonstrated that the aminopropyl groups incorporated in SBA-15 were not decomposed during the preparation procedure and the surfactant P123 was fully removed through ethanol extraction. The modified SBA-15 was an excellent base catalyst in Knoevenagel and Michael addition reactions.     

Synthesis of Cu nanoparticles in mesoporous silica SBA-15 functionalized with carboxylic acid groups

In this study, the mesoporous silica SBA-15 materials containing carboxylic acid groups were used as an effective support to synthesize Cu nanoparticles. Various Cu loading levels from 4% to 13% on SBA-15 catalysts produced an average particle size of 2.8 to 3.1 nm, regardless of the Cu content.     

Preparation, microstructure, and properties of novel low-κ brominated epoxy/mesoporous silica composites

Brominated epoxy resin (BER) composites containing various amounts of SBA-15 and SBA-16 types mesoporous silicas were prepared through the thermal curing with 3-methyl-tetrahydrophthalic anhydride, and their morphologies, dielectric constants (κ), thermal properties and mechanical properties were studied. The investigation suggested that the dielectric constant could be reduced from 4.09 of the pure thermosetting BER to 3.74 and 3.7 by incorporating 3 wt.% SBA-15 and SBA-16, respectively. The reduction of the dielectric constant is attributed to the incorporation of the air voids (κ = 1) stored within the mesoporous silica materials, the air volume existing in the gaps on the interfaces between the mesoporous silica and the BER matrix, and the free volume created by introducing large-sized domains. The BER/mesoporous silica composites also present stable dielectric constants across the wide frequency range. An improvement of thermal stability of the BER is achieved by incorporation of the mesoporous silica materials. The enhanced interfacial interaction between the surface-modified mesoporous silica and the BER matrix has also led to an improvement of the toughness.     

Mesoporous silica spheres from colloids

A novel method has been developed to synthesize mesoporous silica spheres using commercial silica colloids (SNOWTEX) as precursors and electrolytes (ammonium nitrate and sodium chloride) as destabilizers. Crosslinked polyacrylamide hydrogel was used as a temporary barrier to obtain dispersible spherical mesoporous silica particles. The influences of synthesis conditions including solution composition and calcination temperature on the formation of the mesoporous silica particles were systematically investigated. The structure and morphology of the mesoporous silica particles were characterized via scanning electron microscopy (SEM) and N2 sorption technique. Mesoporous silica particles with particle diameters ranging from 0.5 to 1.6 microm were produced whilst the BET surface area was in the range of 31-123 m2 g-1. Their pore size could be adjusted from 14.1 to 28.8 nm by increasing the starting particle diameter from 20-30 nm up to 70-100 nm. A simple and cost effective method is reported that should open up new opportunities for the synthesis of scalable host materials with controllable structures.     

Production of porous silica microparticles by membrane emulsification

A method for the production of near-monodispersed spherical silica particles with controllable porosity based on the formation of uniform emulsion droplets using membrane emulsification is described. A hydrophobic metal membrane with a 15 μm pore size and 200 μm pore spacing was used to produce near-monodispersed droplets, with a mean size that could be controlled between 65 and 240 μm containing acidified sodium silicate solution (with 4 and 6 wt % SiO(2)) in kerosene. After drying and shrinking, the final silica particles had a mean size in the range between 30 and 70 μm. The coefficient of variation for both the droplets and the particles did not exceed 35%. The most uniform particles had a mean diameter of 40 μm and coefficient of variation of 17%. By altering the pH of the sodium silicate solution and aging the gel particles in water or acetone, the internal structure of the silica particles was successfully modified, and both micro- and mesoporous near-monodispersed spherical particles were produced with an average internal pore size between 1 and 6 nm and an average surface area between 360 and 750 m(2) g(-1). A material balance and particle size analysis provided identical values for the internal voidage of the particles, when compared to the voidage as determined by BET analysis.     

Ag-nanoparticle-loaded mesoporous silica: spontaneous formation of Ag nanoparticles and mesoporous silica SBA-15 by a one-pot strategy and their catalytic applications

A facile one-step method was proposed for the successful synthesis of Ag-nanoparticle-loaded mesoporous silica SBA-15 composites, where silver ions and their corresponding reductant aniline were added in the traditional synthetic system of mesoporous silica SBA-15 containing P123 as the surfactant and TEOS as the silica source. Mesoporous silica SBA-15 and Ag nanoparticles were spontaneously formed with Ag nanoparticles embedded in channels and even implanted in frameworks of mesoporous silica SBA-15. A tentative formation process was then proposed according to experimental observations. Furthermore, catalytic activities of Ag-nanoparticle-loaded silica SBA-15 composites toward the reduction of 4-nitrophenol in the presence of NaBH(4) and the reduction of H(2)O(2) were also investigated.     

Copolymers with fluorescence properties in mesoporous silica SBA-15:Synthesis and characterization

A novel copolymer with fluorescence properties in mesoporous silica SBA-15 was prepared via a combination of surface-initiated reversible addition-fragmentation chain transfer(RAFT) polymerization and "click" chemistry.A sufficient amount of peroxide groups were introduced into mesoporous silica SBA-15 channel pores and were further used to initiate the RAFT polymerization of styrene and 4-vinylbenzyl azide,resulting in SBA-15 supported polystyrene-co-poly(4-vinylbenzyl azide) copolymer(PS-co-PVBA/SBA-15) hybrid material.The samples were characterized by Fourier transform infrared spectroscopy(FT-IR),transmission electron microscopy(TEM),thermogravimetry analysis(TGA),N_2 adsorption-desorption isotherms and X-ray diffraction(XRD),respectively.The results show that the styrene and 4-vinylbenzyl azide had copolymerized inside mesoporous silica SBA-15.Subsequently,Npropargyl-carbazole(PC) was connected to PS-co-PVBA/SBA-15 hybrid material via "click" reaction,resulting in PS-co-PVBC/SBA-15 with carbazole side groups hybrid material.The fluorescence spectrum is dominated by a broad band from 350 nm to 400 nm in narrow region and the maximum peak is 362 nm,indicating the characteristic absorption of the carbazole group of PS-co-PVBC/SBA-15 hybrid material.     

以SBA-15为硅源合成多级孔SAPO-11分子筛及其在正十二烷临氢异构化中的应用

以脱除模板剂后的SBA-15为硅源和间接模板剂,在水热条件下制备多级孔SAPO-11分子筛,并通过XRD、SEM、红外光谱、氮气物理吸附-脱附等表征手段对样品的晶相、形貌、酸性和织构性质进行表征。结果表明,以焙烧后的SBA-15为硅源合成出纯相的SAPO-11分子筛,且SBA-15已完全转化。合成的SAPO-11样品呈空心的近方柱体形貌,由宽度为100 nm左右的细条聚集而成,晶粒粒径为1-3 μm。与白炭黑、硅溶胶合成的常规SAPO-11分子筛对比发现,添加SBA-15可在SAPO-11中引入介孔孔道,孔径为5-10 nm,且样品以中强度的Brønsted酸为主,弱Brønsted酸相对较少。以正十二烷为探针分子,考察Pt/SAPO-11催化剂的临氢异构化反应性能。结果表明,多级孔Pt/SAPO-11催化剂具有优良的异构化反应性能。催化剂的高活性和选择性与SAPO-11分子筛的酸性质和孔道结构密切相关,中强度的Brønsted酸量的增加有助于活性提高,同时介孔孔道有利于产物扩散,异构产物的选择性明显提高。     

SBA-15的孔壁碳膜修饰对钴基催化剂结构与催化性能的影响

在惰性气体中焙烧SBA-15制得孔壁被碳修饰的SBA- 15C样品,以它和SBA-15为载体,采用等量浸渍法制备了负载型Co基催化剂,并运用X射线衍射、N2物理吸附、程序升温还原、NH3吸附量热等手段对样品进行了表征.结果表明,SBA- 15C仍保持原有的六方有序的中孔结构,但其孔壁经碳修饰后发生增厚,比表面积略有下降...