无溶剂及微乳液体系中脂肪酶催化红花油水解的动力学

 在无溶剂及二(2-乙基己基)丁二酸酯磺酸钠(AOT)/异辛烷/磷酸盐缓冲液微乳液体系中,研究了黑曲霉脂肪酶催化红花油水解反应的动力学. 结果表明,无溶剂及微乳液体系中反应的活化能分别为32.205和7.391 kJ/mol. 酶在无溶剂体系中的热稳定性高于微乳液中. 无溶剂及微乳液体系中的表观米氏常数分别为0.135和0.101 mol/L. 在两种体系中,乙醇对水解反应的抑制作用均为竞争性可逆抑制,且均在底物浓度大于0.819 mol/L时出现底物抑制现象. 结合胶团催化理论和酯键水解机理对两种体系中酶水解性能的差异进行了解释.     

脂肪酶酶粉催化的无溶剂酯交换反应

硅胶;无溶剂反应;脂肪酶酶粉催化的无溶剂酯交换反应     

脂肪酶直接与硅胶混合催化无溶剂酯化反应的研究

用硅胶作为载体，以癸酸与己醇的酯化反应作为模型，将脂肪酶和底物直接与硅胶混合，用于无溶剂体系催化酯化反应．结果表明体系中水的含量、底物用量比以及反应时间均对酯化反应有较大影响．在该体系中，脂肪酶催化酯合成反应的速度显著增加，反应2h后．转化率可以达到90％以上．而且沉积在硅胶上的脂肪酶可以反复使用多次．     

华根霉全细胞脂肪酶催化合成生物柴油

比较了5种不同商品化脂肪酶和自制的华根霉CCTCCM201021全细胞脂肪酶(RCL)催化油脂合成生物柴油的转化效果,结果表明,RCL能有效应用于无溶剂体系催化合成生物柴油.在无溶剂体系中对该酶催化生物柴油的转酯化反应工艺进行优化,考察了甲醇用量、体系含水量、酶的添加量和反应温度对生物柴油收率的影响,使生物柴油最终收率大于86.0%.在有机溶剂体系中选择不同有机溶剂作为助溶剂进行转酯化反应,发现logP值在4.0～4.5的有机溶剂具有较好的转化效果.其中以正庚烷为助溶剂的转酯化反应具有最高的生物柴油收率86.7%.在无溶剂体系中RCL催化转化油酸和模拟高酸价油脂合成脂肪酸甲酯的研究表明,该酶具有很好的催化合成生物柴油的潜力.     

无溶剂酶促合成癸酸偏甘油酯的热力学和动力学

以Candida antarctic脂肪酶（CAL）为催化剂,对无溶剂微水体系中癸酸与甘油酯化反应的热力学平衡和动力学行为进行研究。用平板冷却猝灭法观察反应体系的初始相态。反应物猝灭态照片表明,相间传质与反应物分散状态有关;酶粒表面局部癸酸浓度相对过剩于界面相浓度。在无溶剂体系中癸酸和甘油的酶促反应不符合Ping-Pong Bi-Bi机制。敞开物体系中单、二、三酯形成的表观热力学平衡方程为：[C]0N[C]/[M]=1/K1 [C] K2[C]^2 K2K3[C]^3,其中[C]0为癸酸的初始摩尔数,[C]为反应物中癸酸的摩尔数,N为甘油与癸酸的初始摩尔比,[M]为反应物中癸酸单甘酯的摩尔数;K1、K2、K3分别为单、二、三酯形成的表观热力学平衡常数：K1＝0.103mmol^-1,K2=0.055mmol/^-1,K3=0.004mmol^-1。     

无溶剂体系脂肪酶催化合成阿魏酸油醇酯

对无溶剂体系中阿魏酸的转酯化疏水改性进行了研究,确立了减压反应器(0.001 MPa)中Novozym 435脂肪酶催化阿魏酸乙酯和油醇进行转酯化反应合成新型抗氧化剂阿魏酸油醇酯的方法.发现水活度(aw)明显影响转酯反应,阿魏酸油醇酯产率在aw＜0.01-0.75范围内随着水活度的增加而降低,推测底物阿魏酸乙酯和产物阿...     

无溶剂体系介孔分子筛SBA-15固定化脂肪酶拆分(R, S)-3-氯-1-苯基丙醇

在无溶剂体系中, 采用介孔分子筛SBA-15固定化P. fluorescens脂肪酶 (PFL)拆分(R,S)-3-氯-1-苯基丙醇. 结果表明, 在以乙酸乙烯酯为酰基供体、 水活度为0.19、 温度为60 ℃、 “记忆”pH为7.0 的优化条件下反应28 h, 酶促拆分转化率(c)达到49.87%, 产物对映体过量值(ee_p)达到98.73%, 显示了良好的应用前景.     

无溶剂体系中酶促合成糖酯

以固定在阴离子树脂上的脂肪酶Novozym435为催化剂,在无溶剂体系中研究了果糖与月桂酸的直接酯化反应.对反应条件进行了优化,在加水量30μL、pH值7.5、月桂酸与果糖摩尔比5∶1、加酶量与底物质量比17%、温度为60℃、反应48 h,达到最大相对转化率为75.6%(以果糖月桂酸双酯计算),比不加水时的49.2%有了较大的提高.产物经TLC分析,果糖月桂酸单酯Rf值为0.44,果糖月桂酸双酯Rf值为0.79,13C NMR鉴定,产物主要是1-β-D-呋喃果糖月桂酸单酯和1,6-β-D呋喃果糖月桂酸双酯.与传统有溶剂反应相比,无溶剂反应更易于后期分离纯化,并节省了溶剂,降低了生产成本.     

无溶剂体系中固定化脂肪酶Candida sp. 99-125催化合成油酸低碳醇酯

采用固定化脂肪酶Candida sp.99-125在无溶剂体系中催化合成油酸低碳醇酯,考察了加酶量、温度、酸醇摩尔比和醇结构对油酸酯化率的影响。结果表明,加酶量为底物质量的3%,最适温度为20℃,酸与醇摩尔比为1∶1,甲醇对该酶有一定的毒性,由于空间位阻效应,该酶对伯醇具有高选择性,对仲醇、叔醇的选择性低,且对长链脂肪酸催化活性高,对带支链的多元酸、多元醇活性低。该酶重复使用5次,酶活性基本没有降低。与传统的化学法相比,用该酶催化合成酯类化合物的色泽更浅。     

无溶剂体系酶促阿魏酸双甘酯合成的研究

对酶催化合成阿魏酸双甘酯的脂肪酶进了筛选和比较,并对影响合成阿魏酸双甘酯的因素(助溶剂、转速、底物比、时间、温度、水含量和硅藻土添加量)进行了探讨,结果表明无溶剂反应体系中阿魏酸双甘酯的产率远远高于含有助溶剂体系中反应.同时优化了反应条:无溶剂体系中在70mg CRL催化下,转速为150 r/m in,底物比为1:1,反应时间为120 h,水含量为10 ug/g,硅藻土添加量为40 mg时产率可达33.25%.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.