Ion-exchange synthesis and improved photovoltaic performance of CdS/Ag2S heterostructures for inorganic-organic hybrid solar cells

A facile ultrasound-assisted ion exchange route was developed for the synthesis of CdS/Ag₂S heterojunctions by ion exchange between the nanostructured CdS film and [Ag(NH₃)₂]⁺ under ultrasonication. The CdS/Ag₂S heterojunction film was characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), UV-vis DRS spectroscopy, photoelectrochemical measurements, and the transient photovoltage (TPV) technique. CdSAg₂S heterojunctions exhibit a dense morphology, enhanced visible light absorption and stronger photocurrent response than the pure CdS films. Poly(3-hexylthiophene) (P3HT) was then spin coated into the CdS/Ag₂S framework. Hybrid solar cells constructed with FTO/CdS/Ag₂S/P3HT/Au display relatively higher power conversion efficiency than FTO/CdS/P3HT/Au.     

Synthesis of CdS, ZnS and Ag2S nanoparticles stabilized by sodium bis(2-ethylhexyl)sulfosuccinate and polyoxyethylenesorbitan monooleate in aqueous medium

The effect of synthesis conditions (molar ratio between precursors, concentration of surfactants, synthesis temperature) on the size of CdS, ZnS and Ag₂S nanoparticles (NPs) stabilized by sodium bis(2-ethylhexyl)succinate and polyoxyethylenesorbitan monooleate was studied. It was established that stabilization by polyoxyethylenesorbitan results in formation of smaller NPs (～8 nm) as compared to that in the presence of sodium bis(2-ethylhexyl)sulfosuccinate (14–60 nm), which is due to the difference between the adsorption rates of these surfactants onto the surface of synthesized NPs. The resulting aqueous dispersions of CdS, ZnS and Ag₂S NPs exhibit long-term stability to sedimentation. The nanoparticle size increases insignificantly with temperature increasing to 65–70°C and rises abruptly at higher temperatures. The increase in the ratio between concentrations of precursors (sulfide and metal ions) also results in an increase in NP size, allowing one to synthesize nanoparticles of prescribed sizes. The optical properties of the resulting nanoparticles were studied. The positions of the exciton peaks and the luminescence intensity peaks of the dispersions of synthesized CdS and ZnS NPs were determined.     

Controlled synthesis and self-assembly of highly monodisperse Ag and Ag(2)S nanocrystals

A facile method to control the synthesis and self‐assembly of monodisperse Ag and Ag₂S nanocrystals with a narrow‐size distribution is described. Uniform Ag nanoparticles of less than 4 nm were obtained by thermolysis of Ag–oleate complexes in the presence of oleic acid and dodecylamine, and monodisperse Ag nanoparticles of less than 10 nm were also prepared in one step by using dodecylamine and oleic acid as capping agents. Moreover, the surface‐enhanced Raman scattering (SERS) properties of the Ag substrates have also been investigated. It is worth mentioning that these Ag nanoparticles and assemblies show great differences in the SERS activities of Rhodamine B dye. In addition, the superlattices of Ag₂S nanocrystals were synthesized with Ag–oleate complexes, alkanethiol, and sulfur as the reactants. The resulting highly monodisperse nanocrystals can easily self‐assemble into interesting superstructures in the solution phase without any additional assembly steps. This method may be extended to the size‐controlled preparation and assembly of many other noble‐metal and transition‐metal chalcogenide nanoparticles. These results will aid the study of the physicochemical properties of the superlattice assemblies and construction of functional macroscopic architectures or devices.     

A Novel Kinetic Approach for Photocatalytic Degradation of Azo Dye with CdS and Ag/CdS Nanoparticles Fixed on a Cement Bed in a Continuous‐Flow Photoreactor

Azo dyes are one of the synthetic dyes that have been used in many textile industries. Azo dye and their intermediate products are toxic, carcinogenic, and mutagenic to aquatic life. Removal of azo dyes is one of the main challenges before releasing the wastes discharged by textile industries. Photocatalytic degradation of azo dyes by nanoparticles is one of the environment‐friendly methods used for the removal of dyes from textile effluents. Therefore, this study focused on degradation of azo dye, Direct Red 264. Photocatalytic degradation of DR 264 azo dye was investigated using CdS and Ag/CdS nanoparticles immobilized on a cement bed in a continuous‐flow photoreactor under UV‐C exposure. The effect of the parameters of type and mass of catalyst, temperature, flow rate, dye concentration, and light intensity were evaluated for azo dye removal. Under optimal conditions, photocatalytic degradation of DR 264 azo dye using Ag/CdS nanoparticles immobilized on a cement bed in a continuous‐flow photoreactor obtained an efficiency of 99.99%. A developed kinetic model was proposed based on the intrinsic elementary reactions. The proposed model is in a good agreement with the Langmuir–Hinshelwood (L–H) equation. The pseudo–steady‐state approximation has considered for the concentration of hydroxyl radicals associated with the L–H model under certain conditions and explains consistently the dependence of the apparent kinetic parameter, k_obs (the reaction rate constant), and K_R (the adsorption equilibrium constant) with the light intensity. Based on the model, k_obs for Ag/CdS was greater than the CdS nanoparticles.     

Stability and optical properties of dispersions of CdS,ZnS, and Ag<Subscript>2</Subscript>S nanoparticles synthesized in microemulsion

CdS, ZnS, and Ag₂S nanoparticles have been synthesized in microemulsion. The synthesis of nanoparticles depend on the composition of the reaction medium and on the proportions of the precursors. The phase diagram for sedimentation stable dispersion of the nanoparticles synthesized in microemulsion has been determined. The region of the stable nanoparticle dispersion is much smaller than the region of the inverse microemulsion in the n-heptane-AOT-H₂O system. The UV-vis absorption and photoluminescence spectra of the CdS, ZnS, and Ag₂S nanoparticles have been investigated. The size of the nanoparticles increases with an increase in droplet size in the microemulsion, and this shifts the exciton peaks.     

A Facile Molecular Precursor‐based Synthesis of Ag2Se Nanoparticles and Its Composites with TiO2 for Enhanced Photocatalytic Activity

The reactions of different silver(I) reagents AgX (X^?=iodide, trifluoroacetate, triflate) with selenoethers R₂Se (R=Me, tBu) in a variety of solvents were investigated in relation with their use as precursors for Ag₂Se nanomaterials. Different reaction conditions led to different reactivities and afforded either molecular complexes or metal selenide nanoparticles. The reactions leading to in situ formation of the metal selenide nanoparticles were then extended in the presence of commercial TiO₂ (P25) to prepare silver selenide–titania nanocomposites with different Ag/Ti ratios. These nanocomposites, well characterized by elemental analysis (Ag, Se), PXRD, TEM, BET, XPS and UV/Vis studies, were investigated as photocatalysts for the degradation of formic acid (FA) solution. The xAg₂Se‐TiO₂ nanocomposites (x=0.01, 0.13 and 0.25 mol %) exhibited a much higher catalytic activity as compared to P25, which is an established benchmark for the photocatalysis under UV light, and retained a good photocatalytic stability after recycling for several times.     

Atom‐Precise Polyoxometalate–Ag2S Core–Shell Nanoparticles

Atomically precise polyoxometalate–Ag₂S core–shell nanoparticles were generated in a top‐down approach under solvothermal conditions and structurally confirmed by X‐ray single‐crystal diffraction as an interesting core–shell structure comprising an in situ generated Mo₆O₂₂^8? polyoxometalate core and a mango‐like Ag₅₈S₃₈ shell. This result demonstrates the possibility to integrate polyoxometalate and Ag₂S nanoparticles into a core–shell heteronanostructure with precisely controlled atomical compositions of both core and shell.     

Discrete Silver(I)‐Palladium(II)‐Oxo Nanoclusters, {Ag4Pd13} and {Ag5Pd15}, and the Role of Metal–Metal Bonding Induced by Cation Confinement

We introduce the class of discrete silver(I)‐palladium(II)‐oxo nanoclusters with the preparation of {Ag₄Pd₁₃} and {Ag₅Pd₁₅}. Both polyanions represent the first examples of noble metal‐capped polyoxo‐noble‐metalates in a fully inorganic assembly, featuring an unprecedented host–guest mode containing hetero‐ and homometallic Ag–Pd and Ag–Ag bonding interactions. Comprehensive theoretical calculations suggest that the Ag–Pd metallic bonds originate partially from surface confinement of Ag^I guest ions onto the anionic polyoxopalladate host that is induced by strong electrostatic forces. This work opens the field of fully inorganic silver‐palladium‐oxo nanoclusters, which can be considered as discrete mixed noble metal precursors for the formation of monodisperse core–shell nanoparticles, with high relevance for catalysis.     

An Atomically Precise Au10Ag2 Nanocluster with Red–Near‐IR Dual Emission

A red–near‐IR dual‐emissive nanocluster with the composition [Au₁₀Ag₂(2‐py?C≡C)₃(dppy)₆](BF₄)₅ ( 1 ; 2‐py?C≡C is 2‐pyridylethynyl, dppy=2‐pyridyldiphenylphosphine) has been synthesized. Single‐crystal X‐ray structural analysis reveals that 1 has a trigonal bipyramidal Au₁₀Ag₂ core that contains a planar Au₄(2‐py?C≡C)₃ unit sandwiched by two Au₃Ag(dppy)₃ motifs. Cluster 1 shows intense red–NIR dual emission in solution. The visible emission originates from metal‐to‐ligand charge transfer (MLCT) from silver atoms to phosphine ligands in the Au₃Ag(dppy)₃ motifs, and the intense NIR emission is associated with the participation of 2‐pyridylethynyl in the frontier orbitals of the cluster, which is confirmed by a time‐dependent density functional theory (TD‐DFT) calculation.     

Improved Photocatalytic Activity and Stability of Nano‐sized Ag/Ag2CO3 Plasmonic Photocatalyst by Surface Modification of Fe(III) Nanocluster

The surface modification of Ag/Ag₂CO₃ with Fe(III) ions has been achieved through simply photoreduction‐impregnation method. The obtained products were characterized by means of X‐ray diffraction (XRD), scanning electron microscopy (SEM), X‐ray photoelectron spectroscopy (XPS), and UV‐vis absorption spectroscopy. Under visible‐light irradiation (γ>420 nm), the Fe(III)/Ag/Ag₂CO₃ sample displays a higher photocatalytic activity and stability than pure Ag₂CO₃ and Ag/Ag₂CO₃ samples for the degradation of methyl orange (MO). The improved photocatalytic activity and stability of this ternary system could be ascribed to the synergetic effect between Ag nanoparticles and Fe(III) nanocluster. The metallic Ag nanoparticles cause an obviously enhanced visible‐light absorption to produce more photogenerated charges, while the Fe(III) works as an active site for the following oxygen reduction to reduce the recombination rate of photogenerated electrons and holes.     

A Three-dimensional Heteronuclear Polymer of [Ag2Fe（SCN）5（DMF）]n Containing Channels and One-dimensional Ag2S2-S-Ag2S2 Chains with Ag…Ag Interaction

Introduction So far, considerable attention has been paid to mag-netic interaction between two different metal ions.1-3 As a potential bridging ligand, thiocyanate can coordinate to a harder metal center with N atom and softer ones with S atom at the same time, resulting in the formation of small ferromagnetic coupling.2 On the other hand, the Fe(III) atom is a good candidate as a hard acid and Ag(I) is a good candidate as a soft acid, so that the Fe(III) centers could be expected to conn…     

Different Silver Nanoparticles in One Crystal: Ag210(iPrPhS)71(Ph3P)5Cl and Ag211(iPrPhS)71(Ph3P)6Cl

Two pure silver nanoparticles (Ag₂₁₀(ⁱPrPhS)₇₁(Ph₃P)₅Cl and Ag₂₁₁(ⁱPrPhS)₇₁(Ph₃P)₆Cl labeled as SD/Ag210 and SD/Ag211 (SD=SunDi), were found to co‐crystallize in forming compound 1 . Single‐crystal X‐ray diffraction (SCXRD) revealed that they differ by only one Ag(PPh₃). Their four‐shell nanoparticles consist of three pure Ag metal shells (Ag₁₉@Ag₅₂@Ag₄₅) shielded by a silver‐organic Ag₈₉(ⁱPrPhS)₇₁Cl[Ag(Ph₃P)]_n outermost shell. The number (n) of Ag(Ph₃P) is five for SD/Ag210 and six for SD/Ag211. The pseudo‐fivefold symmetric Ag nanoparticles exhibit surface plasmon absorption similar to a true metallic state but at the nanoscale. This work exemplifies the important effects of phosphine in stabilizing large silver nanoparticles; and offers a platform to investigate the origin of differences in nanoscale metal materials, even differing by only one metal atom; it also sheds light on the regioselective binding of auxiliary Ph₃P on the surface of silver nanoparticles.     

Environmentally Benign and Efficient Ag2S‐ZnO Nanowires as Photoanodes for Solar Cells: Comparison with CdS‐ZnO Nanowires

In this work, we develop a low‐temperature, facile solution reaction route for the fabrication of quantum‐dot‐sensitized solar cells (QDSSCs) containing Ag₂S‐ZnO nanowires (NWs), simultaneously ensuring low manufacturing costs and environmental safety. For comparison, a CdS‐ZnO NW photoanode was also prepared using the layer‐by‐layer growth method. Ultraviolet photoelectron spectroscopy analysis revealed type‐II band alignments for the band structures of both photoanodes which facilitate electron transfer/collection. Compared to CdS‐ZnO QDSSCs, Ag₂S‐ZnO QDSSCs exhibit a considerably higher short‐circuit current density (J_sc) and a strongly enhanced light‐harvesting efficiency, but lower open‐circuit voltages (V_oc), resulting in almost the same power‐conversion efficiency of 1.2 %. Through this work, we demonstrate Ag₂S as an efficient quantum‐dot‐sensitizing material that has the potential to replace Cd‐based sensitizers for eco‐friendly applications.     

Facile preparation of Ag/Ag2WO4/g‐C3N4 ternary plasmonic photocatalyst and its visible‐light photocatalytic activity

Introducing plasmonic metals into semiconductor materials has been proven to be an attractive strategy for enhancing photocatalytic activity in the visible region. In this work, a novel and efficient Ag/Ag₂WO₄/g‐C₃N₄ (AACN) ternary plasmonic photocatalyst was successfully synthesized using a facile one‐step in situ hydrothermal method. The composition, structure, morphology and optical absorption properties of AACN were investigated using X‐ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and UV–visible diffuse reflectance spectroscopy, respectively. Photocatalytic performance of AACN was evaluated via rhodamine B and tetracycline degradation. The results indicated that AACN had excellent photocatalytic performance for rhodamine B degradation with a rate constant of 0.0125 min^?1, which was higher than those of Ag₂WO₄ and Ag/Ag₂WO₄. Characterization and photocatalytic tests showed that the strong coupling effect between the Ag/Ag₂WO₄ nanoparticles and the exfoliated ultrathin g‐C₃N₄ nanosheets was superior for visible‐light responsivity and reduced the recombination rate of photogenerated electrons and holes. A proposed mechanism is also discussed according to the band energy structure and the experimental results.     

SF and SC Activation of SF6 and SF5 Derivatives at Rhodium: Conversion of SF6 into H2S

The degradation of SF₆ and SF₅ organyls by S? F and S? C bond‐activation reactions at [{Rh(μ‐H)(dippp)}₂] under mild conditions is reported. Fluorido and thiolato species were identified as products or intermediates, and were characterized by X‐ray diffraction analysis and multinuclear NMR spectroscopy. An unprecedented cyclic process for the conversion of the potent greenhouse gas SF₆ into H₂S was developed.     

Unusual NH Activation of 2‐Aminopyrimidine: Supramolecular Assembly into an AgI Metal–Organic Framework

A rare example of coordination at the amino group of NH₂pym (2‐aminopyrimidine) relevant to N? H activation is described that leads to a novel Ag^I–imide 3D metal–organic framework (MOF). The coordination of Ag^I to NH₂pym produced an electron‐withdrawing effect and thus increased its acidity, which facilitated the N? H activation and the subsequent formation of the Ag–imide bond. A cooperative metalation/deprotonation process for the N? H activation of NH₂pym is suggested. Interestingly, photoluminescence of 1 is switched on at the low temperature of 77 K.     

Ultrathin,Porous and Oxygen Vacancies‐Enriched Ag/WO3−x Heterostructures for Electrocatalytic Hydrogen Evolution

Exploring advanced electrocatalysts for electrocatalytic hydrogen evolution is highly desired but remains a challenge due to the lack of an efficient preparation method and reasonable structural design. Herein, we deliberately designed novel Ag/WO_3?x heterostructures through a supercritical CO₂‐assisted exfoliation‐oxidation route and the subsequent loading of Ag nanoparticles. The ultrathin and oxygen vacancies‐enriched WO_3?x nanosheets are ideal substrates for loading Ag nanoparticles, which can largely increase the active site density and improve electron transport. Besides, the resultant WO_3?x nanosheets with porous structure can form during the electrochemical cycling process induced by an electric field. As a result, the exquisite Ag/WO_3?x heterostructures show an enhanced hydrogen evolution reaction (HER) activity with a low onset overpotential of ≈30 mV, a small Tafel slope of ≈40 mV dec^?1 at 10 mA cm^?2, and as well as long‐term durability. This work sheds light on material design and preparation, and even opens up an avenue for the development of high‐efficiency electrocatalysts.     

A macrocycle-assisted nanoparticlization process for bulk Ag2S

We report herein a new nanoparticlization process for the bulk-to-nano transformation of Ag₂S by incorporating both top-down and bottom-up approaches. Bulk Ag₂S was dissolved in solution with the assistance of a macrocyclic ligand, hexamethylazacalix[6]pyridine (Py[6]), to produce polynuclear silver sulfide cluster aggregates. All Ag–S cluster aggregates obtained in three crystalline complexes were protected by Py[6] macrocycles. Removing the protective Py[6] macrocycles by protonation led to the generation of unconventional Ag–S nanoparticles with a large energy gap. Theoretical calculations by a hybrid DFT method demonstrated that the silver sulfide clusters with high Ag/S ratio exhibited more localized HOMO–LUMO orbitals, which consequently enlarged their band gap energies. These experimental and theoretical studies broaden our understanding of the fabrication of nanomaterials by virtue of the advantages of both bottom-up and top-down methods and meanwhile provide a viable means of adjusting the band gap of binary nanomaterials independent of their size.     

A novel Ag/Ag3PO4-IRMOF-1 nanocomposite for antibacterial application in the dark and under visible light irradiation

MOF-5 that sometimes called IRMOF-1 has been intensively studied in recent years to develop efficient photocatalyst to degrade refractory organics and inactivate bacteria for wastewater treatment. In the present work, Ag/Ag₃PO₄ nanoparticles incorporated in IRMOF-1 was successfully prepared via hydrothermal approach. The antibacterial activity of synthesized materials (IRMOF-1, Ag/Ag₃PO₄ nanoparticles and Ag/Ag₃PO₄-IRMOF-1 nanocomposite was compared against two types of bacteria (Escherichia coli (E. coil) as Gram negative and Staphylococcus aureus (S. aureus) as Gram-positive bacteria). The deactivation of the bacteria by the prepared material was measured in the dark and under visible light irradiation. The antibacterial activity of synthesized samples was investigated by determining the minimal inhibitory concentration (MIC), minimal bactericidal concentration (MBC), growth inhibition assay and inhibition zone. The Ag/Ag₃PO₄-IRMOF-1 nanocomposite exhibited stronger antibacterial activities than the Ag/Ag₃PO₄ nanoparticles and IRMOF-1 at all tested bacteria types. Based on inhibition zone, without any light irradiation, Ag/Ag₃PO₄-IRMOF-1 nanocomposite showed activity toward E. coil, but in presence of light nanocomposite depicted activity toward S. aureus. The results demonstrated that antibacterial activity of all synthesized samples in the dark and light against S. aureus bacteria was more than E. coil bacteria. The antibacterial activity mechanism was due to sustained-release of silver ions in the dark and reactive oxygen species (ROS) under visible light. The bioactivity of IRMOF-1 was related to the degradation of the its structure and the release of Zn²⁺ ions into the culture medium that bind to the cell wall and deactivation bacteria.     

A comparative studyof heat‐treated Ag:SiO2 nanocomposites synthesized by cosputtering and sol‐gel methods

In this work, we compared formation and properties of heat‐treated Ag nanoparticles in silica matrix synthesized by RF‐reactive magnetron cosputtering and sol–gel methods separately. The sol–gel and sputtered films were annealed at different temperatures in air and in a reduced environment, respectively. The optical UV‐visible spectrophotometry have shown that the absorption peak appears at 456 and 400 nm wavelength indicating formation of silver nanoparticles in SiO₂ matrix for both the sol–gel and sputtering methods at 100 and 800 °C, respectively. XPS measurements showed that the metallic Ag⁰ nanoparticles can be obtained from both the techniques at these temperatures. According to XPS and AFM analysis, by increasing annealing temperature, the concentration of the Ag nanoparticles on the surface decreased and the nanoparticles diffused into the substrate for the sol–gel films, while for the films deposited by cosputtering method, the Ag surface concentration increased by increasing the temperature. Based on AFM observations, the size of nanoparticles on the surface were obtained at about 25 and 55 nm for sputtered and sol–gel films, respectively, supporting our optical data analysis. In comparison, the sputtering technique can produce Ag metallic nanoparticles with a narrower particle size distribution relative to the sol–gel method. Copyright © 2008 John Wiley & Sons, Ltd.