A novel sandwiched membrane as polymer electrolyte for application in lithium-ion battery

A novel kind of sandwiched polymer membrane was prepared, which consists of two outer layers of electrospun poly(vinyl difluoride) (PVDF) fibrous films and one inner layer of poly(methyl methacrylate) (PMMA) film. Its characteristics were investigated by scanning electron microscopy and X-ray diffraction. The membrane can easily absorb non-aqueous electrolyte to form gelled polymer electrolytes (GPEs). The resulting gelled polymer electrolytes had a high ionic conductivity up to 1.93 × 10⁻³ S cm⁻¹ at room temperature, and exhibited a high electrochemical stability potential of 4.5 V (vs. Li/Li⁺). It is of great potential application in polymer lithium-ion batteries.     

Electrospun octa(3-chloropropyl)-polyhedral oligomeric silsesquioxane-modified polyvinylidene fluoride/poly(acrylonitrile)/poly(methylmethacrylate) gel polymer electrolyte for high-performance lithium ion battery

Gel polymer electrolyte (GPE) based on octa(3-chloropropyl)-polyhedral oligomeric silsesquioxane (OCP-POSS)-modified polyvinylidene fluoride/poly(acrylonitrile) /poly(methylmethacrylate) (PVDF/PAN/PMMA) fibrous membrane was prepared by electrospinning method to improve the thermal stability of GPE and prevent the leakage of liquid electrolyte for lithium ion battery. The effect of OCP-POSS content on the morphology, porosity and electrolyte uptake, mechanical strength, thermal stability of spinning fibrous membrane and ionic conductivity, electrochemical stability window, and interface resistance of GPE was investigated. The cycle performance of cells assembled with GPE was also tested. The results show that the spinning fibrous membrane with 10 wt% OCP-POSS possesses high electrolyte uptake (660%) and excellent thermal stability. The ionic conductivity of corresponding GPE is 9.23 × 10^?3 S cm^?1 at room temperature and the electrochemical stability window is up to 5.82 V; the interface resistance of 10 wt% OCP-POSS modified GPE decreases by 42% after 168 h compared with pure PVDF/PAN/PMMA GPE. Furthermore, cells assembled with 10 wt% OCP-POSS modified GPE show high discharge capacity (166.5 mA h g^?1 at 0.1 C) and excellent cycle stability during 50 cycles. The results indicate that the GPE could improve the safety of lithium ion battery and show great potential in lithium ion battery applications.     

Polymer electrolyte membranes by in situ polymerization of poly(ethylene carbonate‐co‐ethylene oxide) macromonomers in blends with poly(vinylidene fluoride‐co‐hexafluoropropylene)

Salt‐containing membranes based on polymethacrylates having poly(ethylene carbonate‐co‐ethylene oxide) side chains, as well as their blends with poly(vinylidene fluoride‐co‐hexafluoropropylene) (PVDF‐HFP), have been studied. Self‐supportive ion conductive membranes were prepared by casting films of methacrylate functional poly(ethylene carbonate‐co‐ethylene oxide) macromonomers containing lithium bis(trifluorosulfonyl)imide (LiTFSI) salt, followed by irradiation with UV‐light to polymerize the methacrylate units in situ. Homogenous electrolyte membranes based on the polymerized macromonomers showed a conductivity of 6.3 × 10^?6 S cm^?1 at 20 °C. The preparation of polymer blends, by the addition of PVDF‐HFP to the electrolytes, was found to greatly improve the mechanical properties. However, the addition led to an increase of the glass transition temperature (T_g) of the ion conductive phase by ～5 °C. The conductivity of the blend membranes was thus lower in relation to the corresponding homogeneous polymer electrolytes, and 2.5 × 10^?6 S cm^?1 was recorded for a membrane containing 10 wt % PVDF‐HFP at 20 °C. Increasing the salt concentration in the blend membranes was found to increase the T_g of the ion conductive component and decrease the propensity for the crystallization of the PVDF‐HFP component. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 79–90, 2007     

PVDF/PMMA brushes membrane for lithium‐ion rechargeable batteries prepared via preirradiation grafting technique

Poly(methyl methacrylate) (PMMA) was anchored to multiporous poly(vinylidine fluoride) (PVDF) surface via electron beam preirradiation grafting technique to prepare PVDF/PMMA brushes. The conformation of the PVDF/PMMA brushes was verified through Attenuated total reflection‐Fourier transform infra red spectroscopy (ATR‐FTIR), energy dispersive X‐ray spectroscopy (EDX), and scanning electron microscopy (SEM). Thermal stability of PVDF/PMMA brushes was characterized by thermo gravimetric analysis (TGA). The degradation of PVDF/PMMA brushes showed a two‐step pattern. PVDF/PMMA brushes membrane could be used as polymer electrolyte in lithium‐ion rechargeable batteries after it was activated by uptaking 1 M LiPF₆/EC‐DMC (ethylene carbonate/dimethyl carbonate; EC:DMC = 1:1 by volume) electrolyte solution. The activated membrane showed high ionic conductivity, 6.1 × 10^?3 S cm^?1 at room temperature, and a good electrochemical stability up to 5.0 V. The excellent performances of multiporous PVDF‐g‐PMMA membranes suggest that they are suitable for application in high‐performance lithium‐ion batteries. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 751–758, 2008     

Electrochemical characterization of plasticized polymer electrolytes based on ABS/PMMA blends

Electrochemical characteristics of plasticized polymer electrolytes based on poly(acrylonitrile-butadene-styrene) and poly(methyl methacrylate) (abbreviated as ABS/PMMA) blends have been studied. The ionic conductivity of the polymer electrolyte with an ABS/PMMA ratio of 6/4 and a plasticizer content of 60% was highest when the LiClO₄ content was 4.8%. The transference numbers (T ₊) of the polymer electrolytes were measured using the steady-state current method, and the T ₊ values were found to be less than 0.5. The electrolyte system was found to have an electrochemical stability window up to 4.5 V. The properties of the electrode interface in contact with the polymer electrolyte were also investigated by impedance spectroscopy, and the evolution of these spectra as a function of storage time was explained and interpreted using a solid-polymer layer (SPL) model. The time evolution of the impedance parameters indicated that a passivation film grew rapidly on the lithium surface immediately after assembly of the cell. Electronic Publication     

Review on gel polymer electrolytes for lithium batteries

This paper reviews the state-of-art of polymer electrolytes in view of their electrochemical and physical properties for the applications in lithium batteries. This review mainly encompasses on five polymer hosts namely poly(ethylene oxide) (PEO), poly(acrylonitrile) (PAN), poly(methyl methacrylate) (PMMA), poly(vinylidene fluoride) (PVdF) and poly(vinylidene fluoride-hexafluoro propylene) (PVdF-HFP) as electrolytes. Also the ionic conductivity, morphology, porosity and cycling behavior of PVdF-HFP membranes prepared by phase inversion technique with different non-solvents have been presented. The cycling behavior of LiMn₂O₄/polymer electrolyte (PE)/Li cells is also described.     

A novel sandwiched membrane as polymer electrolyte for lithium ion battery

A novel kind of sandwiched polymer membrane was prepared by coating three layers of poly(vinyl difluoride) (PVDF), poly(methyl methacrylate) (PMMA) and PVDF, separately. Its characteristics were investigated by scanning electron microscopy, FT-IR, X-ray diffraction, and differential thermal analysis. It consists of two phases. The outer PVDF layers are porous, and the inner PMMA layer is solid. Since the PMMA has a good compatibility with the carbonate-based liquid electrolyte, the membrane can easily absorb the electrolyte to form a gelled polymer electrolyte (GPE). As a result, the evaporation peak of the liquid electrolyte is increased to 160 °C. Due to very low evaporation of the liquid electrolyte, LiCoO₂ shows good cycling behavior in the range of 4.4–3.0 V when this GPE is used as the separator and polymer electrolyte, and lithium as the counter and reference electrode. This unique sandwiched membrane is promising for application in scale-up lithium ion batteries with high safety and high energy density.     

Ionic conductivity and compatibility studies of blends of poly(methyl methacrylate) and poly(propylene glycol) complexed with LICF3SO3

Stable to atmospheric moisture, adhesive and transparent polymer electrolytes have been prepared by blending poly(methyl methacrylate) (PMMA) with poly(propylene glycol)-425/LiCF₃SO₃ complexes. The blending of the polymers has been achieved by a method developed in our laboratory: free radical polymerization of methylmethacrylate in the polyether/salt matrix. A series of polymer blend complexes varying in PMMA content (up to 20% by weight) and oxygen/metal ratios (25, 16, and 8) have been synthesized and their properties studied. All the samples prepared in this study were found to be optically clear unlike the higher molecular weight poly(propylene glycol)-2000 (PPG-2000) system which required a minimum salt concentration to compatibilize a specific amount of PMMA with PPG. The mechanisms by which the salt holds the otherwise incompatible polymers together in a single phase have been investigated by FT-IR. Our studies show a weak coupling of the ether oxygens in the PPG with the ester groups of the PMMA through the lithium cations. Discrete changes has been observed in the FT-IR spectrum of PMMA when doped with the lithium salt hitherto unnoticed with other dopants. Gel permeation chromatography results of the PMMA samples isolated from the solid electrolytes indicate the molecular weight to vary between 43000 and 121000 with relatively narrow distributions, 1.6?2.0. The ionic conductivities of the polymer blend electrolytes were fairly high (10^?5 S/cm) at room temperature. The PMMA neither significantly influenced the T_g of the blend complexes nor effected the ionic conductivities drastically. The ionic conductivity as a function of temperature followed the empirical Vogel-Tammann-Fulcher equation. The blending of PMMA with PPG/LiCF₃SO₃ complexes was found to impart good adhesiveness to the solid electrolytes while making them stable to atmospheric moisture. © 1992 John Wiley & Sons, Inc.     

Poly(aryl ether ketone) composite membrane as a high‐performance lithium‐ion batteries separator

We described the design and synthesis of a modified poly(aryl ether ketone) bearing phenolphthalein and allyl groups (P‐PAEK) via nucleophilic polycondensation. A new kind of composite separator, crosslinked P‐PAEK/polyvinylidene fluoride (c‐P‐PAEK/PVDF) membrane was successfully prepared using phase separation, phase inversion method, and UV crosslinking technique. As a separator of lithium‐ion battery, c‐P‐PAEK/PVDF membrane demonstrates high porosity and uniform distribution of pores with interconnected pathways. Low thermal shrinkage, distinct shut‐down effect, high liquid electrolyte uptake capacity, and exciting liquid electrolyte wettability of the prepared c‐P‐PAEK/PVDF membrane have been revealed through comprehensive study. Moreover, the c‐P‐PAEK/PVDF membrane was applied to assemble a conventional Li/LiFePO₄ coin cell, which exhibited hopeful cell performance. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 2714–2721     

Preparation of PVDF/PEO-PPO-PEO blend microporous membranes for lithium ion batteries via thermally induced phase separation process

Microporous poly(vinylidene fluoride)/polyethylene oxide-co-polypropylene oxide-co-polyethylene oxide (PVDF/PEO-PPO-PEO, or PVDF/F127) blend membranes were prepared via thermally induced phase separation (TIPS) process using sulfolane as the diluent. Then they were soaked in a liquid electrolyte to form polymer electrolytes. The effects of F127 weight fraction on the morphology, crystallinity and porosity of the blend membranes were studied. It was found that both electrolyte uptake of blend membranes and ionic conductivity of corresponding polymer electrolytes increased with the increase of F127 weight fraction. The maximum ionic conductivity was found to reach 2.94 ± 0.02 × 10⁻³ S/cm at 20 °C. Electrochemical stability window was stable up to 4.7 V (vs. Li⁺/Li). The testing results indicated that the PVDF/F127 blend membranes prepared via TIPS process can be used as the polymer microporous matrices of polymer electrolytes for lithium ion batteries.     

A Gel Polymer Electrolyte with 2D Filler-reinforced for Dendrite Suppression Li-Ion Batteries

Gel polymer electrolytes (GPEs) incorporate both the high ionic conductivity of organic liquid electrolyte and the high safety performance of all-solid-state electrolytes (ASSEs), greatly improving the electrochemical performance of solid polymer electrolytes (SPEs). However, the practical application of GPEs is still limited by inferior interface compatibility, lithium dendrites, etc. Herein, we prepared GPEs based on poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-HFP) further co-blended the two-dimensional sheet inorganic filler hectorite and poly(methyl methacrylate) (PMMA) to improve the mechanical and electrochemical properties of the GPEs. When the content of PMMA and hectorite is optimal, this GPEs have an ionic conductivity of 1.06×10⁻³ S cm⁻¹ and outstanding lithium symmetric cells cycle time of more than 3000 h, indicating that the introduction of filler effectively inhibits the growth of lithium dendrites at room temperature. Moreover, the GPEs adopt a relatively simple solution casting method to provide a fresh idea for the synthesis of high-performance GPEs.     

基于新型交联聚合物电解质的准固态染料敏化太阳能电池

采用柠檬酸(CA)交联聚乙二醇(oligo-PEG, 平均分子量M_w=200, 400, 1000, 2000), 合成具有可生物降解性能的聚柠檬酸-乙二醇(PCE)交联聚酯, 并以此为基体材料制备得到准固态的三维交联型PCE/LiI/I₂聚合物电解质. 采用红外吸收光谱(IR)、核磁共振氢谱(¹H-NMR)、扫描电镜(SEM)和Raman光谱分别对PCE基体的分子结构、聚合物电解质的微观形貌以及导电离子对的存在形式进行表征; 通过线性扫描伏安法(LSV)研究了聚合物电解质的离子扩散系数、电导率以及电池的输出电流-电压(I-V)性能. 结果表明, PEG的分子量影响PCE基体膜的微观形貌及其吸液性能, 从而影响聚合物电解质的离子导电性能及电池的光电性能: 随着PEG分子量M_w从200, 400, 1000增大到2000, PCE基体膜的结构变得疏松, 吸液率增加, 吸液溶胀后的基体中I-3的跃迁活化能降低, 导致电解质的电导率和电池的短路光电流密度随之增加; 在60 mW·cm^-2的入射光强下, 四种电解质对应电池的光电转化效率依次为3.26%、3.34%、4.26%和4.89%.     

Single-ionic gel polymer electrolyte based on polyvinylidene fluoride and fluorine-containing ionomer

The novel single-ionic conductive gel polymer electrolyte was prepared from polyvinylidene fluoride (PVDF), propylene glycol carbonate (PC) and a new fluorine-containing ionomer. Cation-carbonyl interaction behavior, morphology and ionic conductive properties of this gel polymer electrolyte were studied by infrared spectra analysis (IR), nuclear magnetic resonance (NMR), differential scanning calorimetry (DSC), scanning electron microscopy (SEM) and complex impedance analysis. The results showed that the fluorine-containing ionomer was miscible with both PVDF and PC, and that the carbonyl groups in the ionomer and PC could bond competitively with the cation. Both the content of fluorine-containing ionomer and the content of PC had a great effect on morphology and ionic conductive properties of the samples. For this new gel polymer electrolyte, an ionic conductivity of above 10⁻⁴ S cm⁻¹ at room temperature could be reached, and this electrolyte system was a single-ionic kind gel polymer electrolyte with the transport number of the sodium ion exceed 0.99 (t₊>0.99).     

Improving the performance of all-solid-state supercapacitors by modifying ionic liquid gel electrolytes with graphene nanosheets prepared by arc-discharge

Ionic liquid gel polymers have widely been used as the electrolytes in all-solid-state supercapacitors, but they suffer from low ionic conductivity and poor electrochemical performance. Arc discharge is a fast, low-cost and scalable method to prepare multi-layered graphene nanosheets, and as-made graphene nanosheets （denoted as ad-GNSs） with few defects, high electrical conductivity and high thermal stability should be favorable conductive additive materials. Here, a novel ionic liquid gel polymer electrolyte based on an ionic liquid （EM1MNTF2） and an copolymer （P（VDF-HFP）） was modified by the addition of ad-GNSs as an ionic conducting promoter. This modified gel electrolyte shows excellent thermal stability up to 400 ℃ and a wide electrochemical window of 3 V. An all-solid-state supercapacitor based on commercial activated carbon was fabricated using this modified ionic liquid gel polymer electrolyte, which shows obviously improved electrochemical behaviors compared with those of the corresponding all-solid-state supercapacitor using pure ionic liquid gel polymer electrolyte. Specially, smaller internal resistance, higher specific capacitance, better rate performance and cycling stability are achieved. These results indicate that the ionic liquid gel polymers modified by ad-GNSs would be promising and suitable gel electrolytes for high performance all-solid-state electrochemical devices.     

The network gel polymer electrolyte based on poly(acrylate-co-imide) and its transport properties in lithium ion batteries

Poly (acrylate-co-imide)-based gel polymer electrolytes are synthesized by in situ free radical polymerization. Infrared spectroscopy confirms the complete polymerization of gel polymer electrolytes. The ionic conductivity of gel polymer electrolytes are measured as a function of different repeating EO units of polyacrylates. An optimal ionic conductivity of the poly (PEGMEMA₁₁₀₀-BMI) gel polymer electrolyte is determined to be 4.8 × 10^–3 S/cm at 25 °C. The lithium transference number is found to be 0.29. The cyclic voltammogram shows that the wide electrochemical stability window of the gel polymer electrolyte varies from −0.5 to 4.20 V (vs. Li/Li⁺). Furthermore, we found the transport properties of novel gel polymer electrolytes are dependent on the EO design and are also related to the rate capability and the cycling ability of lithium polymer batteries. The relationship between polymer electrolyte design, lithium transport properties and battery performance are investigated in this research.     

Study of Carbamate‐Modified Disiloxane in Porous PVDF‐HFP Membranes: New Electrolytes/Separators for Lithium‐Ion Batteries

A gel electrolyte membrane is obtained through the absorption of a carbamate‐modified liquid disiloxane‐containing lithium bis(trifluoromethane)sulfonimide (LiTFSI) by using macroporous poly(vinylidene fluoride–hexafluoropropylene) (PVDF‐HFP) membranes. The porous membranes are prepared by means of a phase inversion technique. The resulting gel electrolyte membrane is studied by using differential scanning calorimetry, Fourier‐transform infrared (FTIR) spectroscopy, and microscope mapping through coherent anti‐Stokes Raman scattering (CARS) confocal microscopy and impedance spectroscopy. The ionic conductivity of the gel electrolyte is 10^?4 S cm^?1 at 20 °C. FTIR spectroscopy reveals interactions between LiTFSI and the carbonyl moiety of the disiloxane. No interactions between LiTFSI and PVDF‐HFP or between disiloxane and PVDF‐HFP are detected by FTIR spectroscopy. Furthermore, the distribution of the α and β/γ phases of PVDF‐HFP and the homogeneous distribution of disiloxane/LiTFSI in the gel electrolyte membranes are examined by FTIR mapping. CARS confocal microscopy is used to image the three‐dimensional interconnectivity, which reveals a reticulated structure of macrovoids in the porous PVDF‐HFP framework. Owing to properties such as electrochemical and thermal stability of the disiloxane‐based liquid electrolyte and the mechanical stability of the porous PVDF‐HFP membrane, the gel electrolyte membranes presented herein are promising candidates for applications as electrolytes/separators in lithium‐ion batteries.     

Effects of Supporting Electrolytes on Spectroelectrochemical and Electrochromic Properties of Polyaniline‐poly(styrene sulfonic acid) and Poly(ethylenedioxythiophene)‐poly(styrene sulfonic acid)‐based Electrochromic Device

Electrochromic devices are fabricated by using polyaniline (PANI) doped with poly(styrene sulfonic acid) (PSS) as coloring electrodes, poly(ethylenedioxythiophene)‐poly(styrene sulfonic acid) (PEDOT‐PSS) as complementary electrodes, and hybrid polymer electrolytes as gel electrolytes. The device based on LiClO₄‐based electrolyte (weight ratio of PMMA:PC:LiClO₄ = 0.7:1.1:0.3) shows the highest optical contrast and coloration efficiency (333 cm²/C) after 1200 cycles in these devices, and the color changes from pale yellow (?0.5 V) to dark blue (+2.5 V). The spectroelectrochemical and electrochromic switching properties of electrochromic devices are investigated, the maximum optical contrast (ΔT%) of electrochromic device for ITO|PANI‐PSS‖PMMA‐PC‐LiClO₄‐SiO₂‖PEDOT‐PSS|ITO are 31.5% at 640 nm, and electrochromic device based on LiClO₄‐based electrolyte with SiO₂ shows faster response time than that based on LiClO₄‐based electrolyte without SiO₂.     

Ionic Liquid Based Polymer Gel Electrolytes for Use with Germanium Thin Film Anodes in Lithium Ion Batteries

Thermally stable, flexible polymer gel electrolytes with high ionic conductivity are prepared by mixing the ionic liquid 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl)imide (C₄mpyrTFSI), LiTFSI and poly(vinylidene difluoride-co-hexafluoropropylene (PVDF-HFP). FT-IR and Raman spectroscopy show that an amorphous film is obtained for high (60 %) C₄mpyrTFSI contents. Thermogravimetric analysis (TGA) confirms that the polymer gels are stable below ∼300 °C in both nitrogen and air environments. Ionic conductivity of 1.9×10⁻³ S cm⁻² at room temperature is achieved for the 60 % ionic liquid loaded gel. Germanium (Ge) anodes maintain a coulombic efficiency above 95 % after 90 cycles in potential cycling tests with the 60 % C₄mpyrTFSI polymer gel.     

Investigations on poly(methyl methacrylate)-poly(ethylene oxide) hybrid polymer electrolytes with dioctyl phthalate, dimethyl phthalate and diethyl phthalate as plasticizers

Plasticizers can be used to change the mechanical and electrical properties of polymer electrolytes by reducing the degree of crystallinity and lowering the glass transition temperature. The transport properties of gel-type ionic conducting membranes consisting of poly(ethylene oxide) (PEO), poly(methyl methacrylate) (PMMA), LiClO₄ and dioctyl phthalate, diethyl phthalate or dimethyl phthalate (DMP) are studied. The polymer films are characterized by X-ray diffraction, Fourier transform infrared and impedance spectroscopic studies. It is found that the addition of DMP as the plasticizer in the PEO-PMMA-LiClO₄ polymer complex favours an enhancement in ionic conductivity. The maximum conductivity value obtained for the solid polymer electrolyte film at 305 K is 3.529×10^{– 4} S cm^–1. Electronic Publication     

Enhanced electrochemical properties of a novel polyvinyl formal membrane supporting gel polymer electrolyte by Al2O3 modification

Polyvinyl formal (PVFM)‐based dense polymer membranes with nano‐Al₂O₃ doping are prepared via phase inversion method. The membranes and also their performances as gel polymer electrolytes (GPEs) for lithium ion battery are studied by field emission scanning electron microscope, X‐ray diffraction, differential scanning calorimetry, mechanical strength test, electrolyte uptake test, electrochemical impedance spectroscopy, cyclic voltammetry, and charge–discharge test. The polymer membrane with 3 wt % nano‐Al₂O₃ doping shows the improved mechanical strength of 12.16 MPa and electrolyte uptake of 431.25% compared with 10.47 MPa and 310.59% of the undoped sample, respectively. The membrane absorbs and swells liquid electrolyte to form stable GPE with ionic conductivity of 4.92 × 10^?4 S cm^?1 at room temperature, which is higher than 1.77 × 10^?4 S cm^?1 of GPE from the undoped membrane. Moreover, the Al₂O₃‐modified membrane supporting GPE exhibits wide electrochemical stability window of 1.2–4.8 V (vs. Li/Li⁺) and good compatibility with LiFePO₄ electrode, which implies Al₂O₃‐modified PVFM‐based GPE to be a promising candidate for lithium ion batteries. © 2014 Wiley Periodicals, Inc. J. Polym. Sci. Part B: Polym. Phys. 2014 , 52, 572–577