Sensing characteristics of electrostatic inductive sensor for flow parameters measurement of pneumatically conveyed particles

The spatial sensitivity, spatial filtering effect, temporal frequency response characteristics and bandwidth are important parameters influencing the accuracy and response speed of a ring-shaped electrostatic inductive sensor. In this paper, the charge induced on the ring-shaped sensor with different geometric sizes from a single particle having a unity charge was modeled mathematically. And from the numerical solution obtained using the finite element analysis software ANSYS, the spatial sensitivity of the sensor was derived. The effect of the geometric size of the sensor on the spatial sensitivity was also investigated, and its spatial filtering fundamental theory and spatial filtering effect were also analyzed quantitatively. The temporal frequency response characteristics of the sensor were also derived. The experimental results on a gravity-fed conveyor were presented. The theoretical and experimental results obtained demonstrate that the ring-shaped sensor acts as a low-pass filter in the spatial frequency domain and its spatial frequency characteristics are closely related to the radial position of the charged particle and the axial length of the electrode. The measurement system, including the probe and signal conditioning circuit, acts as a band-pass filter, and the radial position, the axial length of the electrode, particle velocity and particle size have important effects on the temporal frequency characteristics of the measurement system.     

Investigations into sensing characteristics of electrostatic sensor arrays through computational modelling and practical experimentation

Recently, great advance has been made on electrostatic sensing techniques for gas–solid flow measurement. However, reports on research studies of the sensing mechanism and characteristics of the electrostatic sensor arrays (ESA) are scarce. The ESA is a key element of the Electrostatic Tomography system (EST) and multi-channel electrostatic sensors for the local characteristic measurement of gas–solid flow. The geometric sizes of the ESA and the velocity and distribution of particles in the pipeline have important effects on the spatial sensitivity, spatial filtering effect and temporal frequency response of the ESA. In this paper, the charge induced on the electrodes of an ESA with different geometric sizes from a single particle having a unity charge is modelled mathematically, and the 3-dimensional electrostatic field due to the charged particle in the sensing zone of the ESA is solved by using a Finite Element Method. The effects of geometric and material parameters of the ESA, including the width and angel of the electrode, the thickness, length and permittivity of the dielectric pipe, the radius of metal screening on the sensing field of the electrodes are investigated numerically. Furthermore a computational model of the sensitivity of the ESA is proposed based on a fitted Gaussian function to the finite element results and its spatial filtering characteristics are also theoretically analyzed. The temporal frequency response of the ESA is also derived. Experimental work is performed on a purpose-built particle flow test rig to verify the modelling results. The theoretical and experimental results obtained demonstrate that the ESA acts as a low-pass filter in the spatial frequency domain. The measurement system, including the ESA and an interface circuit, acts as a band-pass filter. And the space position of charged particle, the electrode width and particle velocity affect the temporal frequency responses of the ESA. These results provide the basis for the performance improvement and optimized design of the ESA.     

SOA-fiber ring laser and its application to electric field sensing in frequency domain

We have developed a novel optical fiber ring laser using a semiconductor optical amplifier (SOA) as the gain medium, and taking advantage of polarization anisotropy of its gain. The laser can control the oscillation frequency difference between two counterpropagating lights by incorporating a birefringent medium into the ring resonator. Since the frequency difference is proportional to the birefringence, it can be measured to detect the beat frequency generated by combining two counterpropagating lights and the laser can be applied to an optical fiber sensor whose detecting signal is in frequency domain. Electric field sensor was demonstrated with a lithium niobate crystal as a sensing probe.     

Treatment of submicron particles using an electrostatic agglomerator in DC-negative voltage: Re-entrainment experimental study and modeling

The aim of this study is to highlight the re-entrainment phenomenon encountered with an electrostatic agglomerator having a fibrous collecting electrode and treating submicron particles. The idea is to propose a process to control the particle number emitted by automotive diesel engines. Rather than trying to directly measure agglomerates of diesel particles exiting the agglomerator, we propose working with a synthetic submicron aerosol dispersed in ambient filtered air as a representative exhaust gas. The study will contribute to build a numerical modeling of the behavior of particles in such a process. The particular point that will be treated here is the collected particle re-entrainment as micron-sized agglomerates. We propose a joint experimentation/modeling approach to approximate the re-entrained aerosol size distribution in controlled conditions. From the modeling point of view, a local approach which uses the method of the balance of moments on agglomerates provides the re-entrained particle size in the agglomerator, according to the filtration conditions. The experimental approach confirms the clearly micron-sized character of the re-entrained agglomerates. This is unambiguously shown by measuring a greater micron particle numerical concentration downstream from the agglomerator than upstream. We show that the fluorescein submicron particles use can greatly simplify the characterization of an electrostatic agglomerator by allowing the use of a commercial laser granulometer to measure the size and the number of the generated agglomerates.     

A Multi‐Electrode Approach for On‐Line Characterisation of Size and Shape

A multi‐electrode approach is proposed for on‐line characterisation of particle size and shape in dilute particulate suspensions. Based on an electrozone principle, the approach uses four electrodes in a tube rather than two electrodes across an aperture employed in conventional methods. The outer two electrodes are used for current injection, while the inner two electrodes yield voltage measurement. A sensor designed in this way can reduce errors of false counts and oversizing that may occur in conventional methods, thus providing more accurate particle sizing. It is also possible to use the signal slope along with signal peak for particle size and shape characterisation. Both theoretical modelling and experiments were conducted, showing that particle aspect ratio along with particle diameter can be obtained, for example, for cylindrical particles.     

基于超声回波重组相位分析的颗粒粒径测量方法

将超声波作用于沉降的颗粒时,由于颗粒的移动,超声回波会出现相位差异。该文通过对测量杯中某一确定深度处的回波信号进行相位分析和重组,发现重组后信号的频率可以计算出粒径;并分别对两种不同粒径分布的聚甲基丙烯酸甲酯(PMMA)微球悬浮液进行了超声波信号采样重组和去噪的实验,实验结果经小波时频方法分析后,证实了颗粒粒径分布与重组信号频率构成的确存在很高的相关性。     

Performance characteristics between horizontally and vertically oriented electrodes EHD ESP for collection of low-resistive diesel particulates

The novel electrohydrodynamically-assisted electrostatic precipitator (EHD ESP) was developed to suppress particle reentrainment for collection of low resistive diesel particulates. The collection efficiency was compared between vertically and horizontally oriented electrodes of the EHD ESP using 400 cc diesel engine. The particle size dependent collection efficiency was evaluated for the particle size ranging in 20 to 5000 nm using a scanning mobility particle sizer (SMPS) and a particle counter (PC). Both horizontally and vertically oriented EHD ESP showed an excellent suppression of particle reentrainment. However, the horizontally oriented electrode EHD ESP showed significantly improved for the particle size of 300–500 nm in comparison with vertically oriented electrode EHD ESP, resulting in more than 90% collection efficiency for all particle size range. The EHD ESP has high potential especially for highly concentrated marine diesel engine emission control.     

A discrete droplet transport model for predicting spray coating patterns of an electrostatic rotary atomizer

Electrostatic spray (E-spray) coating is widely used for coating conductive substrates. The combination of a high-velocity shaping air, an imposed electric field and charged droplets, leads to higher transfer efficiency than conventional spray coating. In this paper, a mathematical model of droplet transport in E-spray is presented which enables simulating the coating deposition rate profile. A dilute spray assumption (no particle–particle interactions) allows modeling single-droplet trajectories resulting from a balance of electrostatic force, drag and inertia. Atomization of liquid droplets is not modeled explicitly—rather an empirical correlation is used for the mean droplet size while individual droplet sizes and starting locations are determined using random distributions. Strong coupling requires the electrostatic field and droplet trajectories be determined iteratively by successive substitution with relaxation. The influences of bell-cup voltage and atomization constant on the coating deposition rate profile, mass transfer efficiency and droplet trajectories are also shown. Using individually predicted droplet trajectories and impact locations, a static coating deposition rate profiles is determined. For the parametric values considered in this paper, the predicted spray is a cone hollow with no deposition in the center, a heavy ring near the center, and a tapering of thickness toward the outer edge.     

激光尘埃粒子计数器微型光学传感器的研究

研制成功便携式激光尘埃粒子计数器的核心部件———微型光学传感器。该传感器采用直角散射光收集形式,以高功率半导体激光器作为光源,同时采用高性能的PIN型光电二极管作为光电探测器。散射光收集系统为单一大数值孔径的球面反射镜,其对粒子散射光的收集角范围从20°到160°。粒子散射光信号是脉冲信号,其频谱成份主要在高频段,所以在PIN型光电二极管后用一个带通式前置放大器来消除外界的低频噪声,根据米氏散射理论计算了该光学传感器的光散射响应特性,并用聚苯乙烯标准粒子实测了该光学传感器的性能。结果表明,该系统具有高的信噪比、计数效率和尺寸分辨本领。     

A domain decomposition method for three species modeling of multi-electrode negative corona discharge – With applications to electrostatic precipitators

The negative corona discharge problem for multi-electrode geometries is modeled by a three species model. The equations are solved using domain decomposition, by recognizing that multiple species are only present in a small part of the domain, and hence only need to be incorporated locally in the model.The method is applied to an industrially relevant three wire electrostatic precipitator geometry. The calculated current density is in good agreement with experimental data. To further illustrate applications of the three species solution, it is used for coupled particle, fluid, and electrostatic simulations to analyze particle collection properties.     

Semiconductor Optical Amplifier (SOA)-Fiber Ring Laser for Sensor Application

A bi-directional fiber ring laser with a semiconductor optical amplifier has been developed in which a frequency difference between the counter-propagating oscillations is controlled by an introduced birefringent medium. With the material which causes the retardation change by a physical phenomenon to be measured, the laser in this study is applicable to a novel fiber sensor of which the sensing signal is obtained in a frequency domain.     

基于霍夫变换与线性啁啾变换的粒子全息图分析方法研究

基于霍夫变换及线性啁啾变换,提出在空域及频域中分析数字全息图中颗粒粒径大小的方法.在对粒子全息图进行降噪滤波、边缘提取等预处理后,利用弦中点霍夫变换检测粒子的圆心位置,然后以圆心为起点径向扫描出归一化光强分布曲线,求出空域第一个极小值位置.对光强信号做傅里叶变换,结合线性啁啾变换做局部频谱细化,求出频域第一个极小值位置.利用所得极小值位置,代入公式,即可求解颗粒粒径大小.数值计算结果表明,对于粒子间距较大的粒子全息图,该方法误差在2.5%以内.     

基于二阶滤波器的消光起伏谱颗粒测量结果

消光起伏频谱法是一种新的测量两相流系统中颗粒粒径分布和浓度的方法,装置简单,操作方便,适合实时、在线测量。采用二阶低通滤波器对起伏的透射率信号分析,得到消光起伏频谱实验数据,并利用改进的Chahine循环方法计算得到颗粒的粒径分布和浓度信息。重点讨论高浓度情况,包括对特征函数频率响应的修正和对其阶高修正两个方面,得到修正参量并运用到反演算法中从而得到正确的测量结果。测量结果表明,通过高浓度修正,消光起伏频谱法可以在很大的颗粒浓度动态范围得到合理的测量结果,其可测颗粒最大体积分数视颗粒的大小而定。     

Ultrasonic sensor for predicting sugar concentration using multivariate calibration

This paper presents a multivariate regression method for the prediction of maltose concentration in aqueous solutions. For this purpose, time and frequency domain of ultrasonic signals are analyzed. It is shown, that the prediction of concentration at different temperatures is possible by using several multivariate regression models for individual temperature points. Combining these models by a linear approximation of each coefficient over temperature results in a unified solution, which takes temperature effects into account. The benefit of the proposed method is the low processing time required for analyzing online signals as well as the non-invasive sensor setup which can be used in pipelines. Also the ultrasonic signal sections used in the presented investigation were extracted out of buffer reflections which remain primarily unaffected by bubble and particle interferences.     

基于CCD传感的激光粒度测试技术研究

颗粒测试在工业生产和科学研究中涉及的领域非常广泛,常用的颗粒粒度及其分布的测试方法是激光粒度测试法,其具有测试精度高、测量速度快、重复性好和可测粒径范围宽等突出优点。CCD传感器有灵敏度高、分辨率高、噪声小和较大的动态范围等优点,其作为激光粒度仪的探测器提高光强分辨率的应用已经很普遍了。为提高测量精度,通过对CCD传感技术的研究,应用图像处理的方法来设计光电探测器,搭建了基于米氏散射原理的激光粒度测试系统。实验结果表明,用CCD传感器采集光散射图像,再对图像进行处理,D50与D10误差在6%之内,D90误差在1%之内,降低了测量的重复误差。     

Sensor design for development of tribo-electric tomography system with increased number of sensors

Electrodynamic sensor, which can also be called as tribo-electric sensor, senses the electrostatic charge carried by the particle. The tomography system using electrodynamic sensor is called as tribo-electric tomography system. Source of the signal induced on the electrodynamic sensor is brought by the object to be measured and no excitation circuit is necessary. This electrodynamic sensing is a passive sensing and the fast and light weighted tomography system is expected. On the other hand, most of tomography system, like capacitance tomography or resistance tomography, demands excitation circuit and is an active sensing. The number of measurements with the passive sensing is equal to the number of sensors and that of active sensing is the number of the combinations of two sensors. The passive sensing tomography system demands more sensors to be settled. We plan to improve in reconstructed images by increasing the number of the electrodynamic sensors in tribo-electric tomography system. We investigate the influence of surface area to signal intensity solving the electrical field in the sensing zone using finite element method.     

Application of the electrostatic mean value theorem to electrostatic sensor electrodes

We present a method for approximating the potential of conducting objects due to a known electrostatic source. The method involves averaging the incident potential over the conductor surface or volume region, which is known to give the exact value for a perfectly conducting sphere. The method is extended to spheroidal geometries, both prolate and oblate, to study the error incurred for deviations from the spherical case. Exact values for the spheroid potentials are derived and compared with those obtained by the mean value approximations. The result for the oblate spheroid is extended to the case of a two-dimensional electrostatic disk. The approximations are proposed as a method for predicting the potential of conducting electrodes used with electrostatic sensors for the measurement of electrostatic field disturbances. In this regard, the mean value approximation is applied to determine the source to electrode mutual capacitance, which is implemented in the model for the sensor system. Electrostatic disk electrodes are used with an electrostatic disturbance sensor to experimentally validate the application of the mean value approximation.     

等离子体环境下孤立导体表面充电时域特性研究

航天器在等离子体环境下的表面充放电受到多种因素影响, 其中充电时间是影响静电放电频次的一个重要因素. 本文从等离子体的微观结构出发, 同时考虑材料参数特性, 在对每个粒子运用力学原理的基础上, 以统计方法 推导出孤立导体球表面充电电位时域表达式. 利用电位时域表达式推导出孤立导体球净电荷量时域表达式及静电场能量时域表达式. 以较低非极地地球轨道和较高地球同步轨道为例对孤立导体球电位、 净电荷量及静电场能量的时域特性进行了讨论, 分析了空间环境参数和导体球半径大小对表面充电的影响, 总结出等离子体环境下孤立导体表面充电时域特性规律. 关键词： 等离子体 孤立导体 表面带电 时域     

Improved holographic particle sizing by using absolute values of the wavelet transform

A new method for sizing particle from in-line particle holograms by using absolute values of the wavelet transform is proposed in order to improve accuracy in measurements. The proposed method provides direct calculation of the particle size by using spatial frequency information of a chirp signal at minima position of an envelope function. Simulation and experimental results are presented.     

Direction of arrival estimation and signal recovery based on single snapshot compressed sensing in frequency domain

Direction of arrival(DOA) estimation and signal recovery is the base of the underwater target localization,tracking and recognition.Based on the compressed sensing theory,a method for DOA estimation and source signal recovery is proposed using the single snapshot processing of the received array signal in frequency domain.The received array signal are transformed to frequency domain,and the single snapshot data in frequency domain are regarded as the measured data of the compressed sensing.According to the frequency,searching orientation and array manifold,the overcomplete array manifold is constructed as the sensing matrix of the compressed sensing.Both the target signal and power of the searching orientation are estimated by the basis pursuit method to complete DOA estimation and signal recovery.Simulation results show that the proposed method has a number of advantages over the minimum variance distortionless response(MVDR) method,including improved robustness to noise,fewer requirement in number of sensors and snapshots.And the correlation coefficient of the signal reaches up to 0.89.Experiment results in real environments verify that the proposed method performs more effectively in the detection of weak targets than the MVDR method and can be applied to real sonar system.