Donnan permselectivity in layer-by-layer self-assembled redox polyelectrolye thin films

Redox polyelectrolyte multilayers have been assembled with use of the layer-by-layer (LBL) deposition technique with cationic poly(allylamine) modified with Os(bpy)(2)ClPyCHO (PAH-Os) and anionic poly(styrene)sulfonate (PSS) or poly(vinyl)sulfonate (PVS). Different behavior has been observed in the formal redox potential of the Os(II)/Os(III) couple in the polymer film with cyclic voltammetry depending on the charge of the outermost layer and the electrolyte concentration and pH. The electrochemical quartz crystal microbalance (EQCM) has been used to monitor the exchange of ions and solvent with the external electrolyte during redox switching. At low ionic strength Donnan permselectivity of anions or cations is apparent and the nature of the ion exclusion from the film is determined by the charge of the topmost layer and solution pH. At high electrolyte concentration Donnan breakdown is observed and the osmium redox potential approaches the value for the redox couple in solution. Exchange of anions and water with the external electrolyte under permselective conditions and salt and water under Donnan breakdown have been observed upon oxidation of the film at low pH for the PAH-Os terminating layer. Moreover, at high pH values and with PVS as the terminating layer EQCM mass measurements have shown that cation release was masked by water exchange.     

Assembly of multilayer films from polyelectrolytes containing weak and strong acid moieties

Multilayer films were assembled from a copolymer containing both weakly and strongly charged pendant groups, poly(4-styrenesulfonic acid-co-maleic acid) (PSSMA), deposited in alternation with poly(allylamine hydrochloride) (PAH). The strongly charged groups (styrene sulfonate, SS) are expected to form electrostatic linkages (to enhance film stability), while the weakly charged groups (maleic acid, MA) can alter multilayer film properties because they are responsive to external pH changes. In this study, we varied several assembly conditions such as pH, SS/MA ratio in PSSMA, and the ionic strength of the polyelectrolyte solutions. The multilayer films were also treated by immersion into pH 2 and 11 solutions after assembly. Quartz crystal microgravimetry and UV-visible spectrophotometry showed that the thickness of PSSMA/PAH multilayers decreases with increasing assembly pH regardless of whether salt was present in the polyelectrolyte solutions. When no salt was added, the multilayers are thinner, smoother, and grow less regularly. Atomic force microscopy images indicate that the presence of salt in polyelectrolyte solutions results in rougher surface morphologies, and this effect is especially significant in multilayers assembled at pH 2 and pH 11. When both polyelectrolytes are adsorbed at conditions where they are highly charged, salt was necessary to promote regular multilayer growth. Fourier transform infrared spectroscopy studies show that the carboxylic acids in the multilayers are essentially ionized when assembled from different pHs in 0.5 M sodium chloride solutions, whereas some carboxylic acids remain protonated in the multilayers assembled from solutions with no added salt. This resulted in different pH stability regimes when the multilayers were exposed to different pH solutions, post assembly.     

Dynamics of ion exchange between self-assembled redox polyelectrolyte multilayer modified electrode and liquid electrolyte

A probe beam deflection (PBD) study of ion exchange between an electroactive polymer poly(allylamine)-bipyridyl-pyridine osmium complex film and liquid electrolyte is reported. The PBD measurements were made simultaneously to chronoamperometric oxidation-reduction cycles, to be able to detect kinetic effects in the ion exchange. Layer-by-layer (LbL) self-assembled redox polyelectrolyte films with osmium bipyridyl complex covalently attached to poly(allylamine) (PAH-Os) and poly(styrene sulfonate) (PSS) have been built by alternate electrostatic adsorption from soluble polyelectrolytes. The ionic exchange during initial conditioning of the film ("break-in") undergoing oxidation-reduction cycles and recovery after equilibration in the reduced state have shown an exchange of anions and cations with time lag between them. The effect of the nature of cation on the ionic exchange has been investigated with dilute HCl, LiCl, NaCl, and CsCl electrolytes. The ratio of anion to cation exchanged at the film-electrolyte interface has a strong dependence on the nature of charge in the topmost layer, that is, when negatively charged PSS is the capping layer, a larger proportion of cation exchange is observed. This demonstrates that the electrical potential distribution at the redox polyelectrolyte multilayer (PEM)/electrolyte interface determines the ionic flux in response to charge injection in the film.     

Photo-cross-linkable polyelectrolyte multilayers for 2-D and 3-D patterning

We report the synthesis of poly(acrylic acid-ran-vinylbenzyl acrylate) (PAArVBA), a photo-cross-linkable weak polyelectrolyte, and its incorporation into polyelectrolyte multilayer (PEM) films. PEM films assembled from PAArVBA and poly(allylamine hydrochloride) (PAH) are found to exhibit similar thickness trends with assembly pH as those previously reported for poly(acrylic acid) (PAA)/PAH multilayers. Swelling properties of the as-built and photo-cross-linked films are studied by in situ ellipsometry. Two-dimensional masking techniques are used to pattern regions of high and low swelling, as confirmed by atomic force microscopy (AFM), and to provide spatial control over the low-pH-induced microporosity transition exhibited by PAH/PAA PEMs. Films containing alternating blocks of PAH/PAArVBA bilayers and PAH/PAA bilayers were assembled, laterally photopatterned, and exposed to low-pH solution to generate nanoporosity leading to patterned Bragg reflectors, thereby demonstrating three-dimensional control over film structure in these weak PEM assemblies.     

Fabrication of Covalently Linked PAH/PVS Layer-by-layer Assembled Multilayers via a Post-photochemical Cross-linking Strategy

A post-photochemical cross-linking strategy was successfully demonstrated to enhance the stability of polyelectrolyte poly(allylamine hydrochloride)(PAH)/poly(vinylsulfonic acid sodium salt)(PVS) multilayers. Conventional polyelectrolyte multilayers of PAH/PVS are usually fabricated through electrostatic layer-by-layer(LbL) assembly, resulting in poor stability, especially in basic solutions, which leads to the urgent demand for converting weak electrostatic interactions into covalent bonds to enhance the stability of the multilayers. This stability problem has been ultimately addressed by post-infiltrating a photosensitive cross-linking agent, 4,4'-diazostilbene-2,2'- disulfonic acid disodium salt(DAS), into the LbL assembled films to initiate the photochemical reaction to cross-link the multilayers. The obviously improved stability of the photo-cross-linked multilayers was demonstrated through experiments with basic solution treatments. Compared to the complete decomposition of uncross-linked multilayers in basic solution, over 74.4% of the covalently cross-linked multilayers were retained under the same conditions, even after a longer duration of basic solution treatment.     

Redox and acid-base coupling in ultrathin polyelectrolyte films

A single layer of poly(allylamine) with a covalently attached osmium pyridine-bipyridine complex adsorbed onto a Au surface modified by mercaptopropanesulfonate has been studied theoretically with a molecular approach and experimentally by cyclic voltammetry. These investigations have been carried out at different pHs and ionic strengths of the electrolyte solution in contact with the redox polyelectrolyte modified electrode. The theory predicts strong coupling between the acid-base and redox equilibria, particularly for low ionic strength, pH close to the pKa, and high concentration of redox sites. The coupling leads to a decrease in the peak potential at pH values above the apparent pKa of the weak polyelectrolyte, in good agreement with the experimental pH dependence at 4 mM NaNO3. Theoretical calculations suggest that the inflection point in the peak position versus pH curves can be used to estimate the apparent pKa of the amino groups in the polymer. Comparison of the apparent pKa for PAH-Os in the film with that of poly(allylamine) reported in the literature shows that the underlying charged thiol strongly influences charge regulation in the film. A systematic study of the film thickness and the degree of protonation in sulfonate and amino groups for solutions of different pH and ionic strength shows the coupling between the different interactions. It is found that the variation of the film properties has a non-monotonic dependence on bulk pH and salt concentration. For example, the film thickness shows a maximum with electrolyte ionic strength, whose origin is attributed to the balance between electrostatic amino-amino repulsions and amino-sulfonate attractions.     

Assembly of poly(N-isopropylacrylamide)-co-acrylic acid microgel thin films on polyelectrolyte multilayers: Effects of polyelectrolyte layer thickness, surface charge, and microgel solution pH

Temperature- and pH-sensitive poly(N-isopropylacrylamide)?Cco-acrylic acid (pNIPAm-co-AAc) microgels were deposited on glass substrates coated with polyelectrolyte multilayers composed of the polycation poly(allylamine hydrochloride) (PAH) and the polyanion poly(sodium 4-styrenesulfonate) (PSS). The microgel density and structure of the resultant films were investigated as a function of: (1) the number of PAH/PSS layers (layer thickness); (2) the charge on the outer layer of the polyelectrolyte multilayer film; and (3) the pH of microgel deposition solution. The resultant films were studied by differential interference contrast optical microscopy, atomic force microscopy, and scanning electron microscopy. It was found that the coverage of the microgels on the surface was a complex function of the pH of the deposition solution, the charge on the outer layer of the polyelectrolyte thin film and the PAH/PSS layer thickness; although it appears that microgel charge plays the biggest role in determining the resultant surface coverage.     

Multilayers of weak polyelectrolytes of low and high molecular mass assembled on polypropylene and self-assembled hydrophobic surfaces

Hydrophobic self-assembled octadecyltrichlorosilane (ODTS), ultrathin films of polypropylene, and ODTS modified with cationic dioctadecyldimethylammonium bromide are employed as substrates for deposition of multilayers of poly(allylamine hydrochloride) and poly(acrylic acid) from aqueous solution. The assembly of highly dissipative polyelectrolyte multilayers (PEMs) is demonstrated by quartz crystal microgravimetry. The initial rate of adsorption is faster and the adsorbed amount larger on the cationic surface, while the detailed structure of the PEMs, as determined by atomic force microscopy imaging, is related primarily to the molecular weight of the adsorbing polymers. A more extensive PEM adsorption on the hydrophobic surfaces takes place with increasing ionic strength of the background electrolyte solution. The water contact angle depends on the type of polymer adsorbed as the outermost layer, indicating that, despite the expected interdiffusion for the different polymer chains, there is a net macromolecular segregation to the free surface. Surface modification with the high molecular weight PEMs produces a more marked reduction of the hydrophilicity of the substrate.     

Layer-by-layer electrostatic deposition of biomolecules on surfaces for molecular recognition, redox mediation and signal generation

Layer-by-layer supramolecular structures composed of alternate layers of negatively charged enzymes and cationic redox polyelectrolyte have been assembled. Glucose oxidase (GOx), lactate oxidase (LOx) and soybean peroxidase (SBP) have been electrically wired to the underlying electrode by means of poly(allylamine) with [Os(bpy)2ClPyCOH]+ covalently attached (PAA-Os) in organized structures with high spatial resolution. Biotinylated glucose oxidase has also been used to assemble step-by-step on antibiotin goat immunoglobulin (IgG) layers and the enzyme was electrically wired by PAA-Os. These spatially organized multilayers with mono- and bienzymatic schemes can work efficiently in molecular recognition, redox mediation and generation of an electrical signal. The concentration of redox mediator integrated into the multilayers, obtained from the voltammetric charge and an estimation of the layer thickness, exceeds by 100-fold the amount of deposited enzyme assessed by quartz crystal microbalance. Differences in GOx electrical wiring efficiency have been detected with the different assembling strategies. The surface concentration of electrically wired enzyme represents a small proportion of all the enzyme molecules present in the multilayers which can be oxidized by the soluble mediator [Os(bpy)2Cl PyCOOH]Cl. This proportion, as well as the rate of FADH2 oxidation by PAA-Os, increases with the number of electrically wired enzyme layers and with the spatial accessibility of the Os moiety to the enzyme active center.     

Combined effect of spin speed and ionic strength on polyelectrolyte spin assembly

Polyelectrolyte spin assembly (PSA) of multilayers is a sequential process featuring adsorption of oppositely charged polyelectrolytes from dilute solutions undergoing spin-coating flow. Here, we report on the dependence of PSA multilayer buildup of poly(sodium 4-styrenesulfonate) and poly(allylamine hydrochloride) on solution ionic strength and spin speed. We observed that at a given spin speed, the PSA coating growth rate (thickness/bilayer) and polymer surface coverage shows a nonmonotonic dependence on salt concentration, first increasing and then decreasing with increasing solution ionic strength. This is argued to be a manifestation of two competing mechanisms responsible for the layer formation. At low salt concentrations, the electrostatic interactions control the multilayer assembly process, while at high salt concentrations it is dominated by shear flow. We explain this nonmonotonic behavior in the framework of a Flory-like theory of multilayer formation from polyelectrolyte solution under shear flow. Additionally, the PSA process led to multilayer coatings with a radial dependence on thickness at lower spin speed in the shear-dominated regime. On increasing spin speed, such radial dependence subsided, eventually leading to uniform coatings by planarization. The surface topography of the multilayered coatings adsorbed at salt concentration less than 0.1 M was flat and featureless for all studied spin speeds. Unique morphological features in the films were formed at salt concentration higher than 0.1 M, the size of which depended on the spin speed and solution ionic strength.     

Layer-by-layer electrostatic self-assembly of single-wall carbon nanotube polyelectrolytes

We have used anionic and cationic single-wall carbon nanotube polyelectrolytes (SWNT-PEs), prepared by the noncovalent adsorption of ionic naphthalene or pyrene derivatives on nanotube sidewalls, for the layer-by-layer self-assembly to prepare multilayers from carbon nanotubes with polycations, such as poly(diallyldimethylammonium) or poly(allylamine hydrochloride) (PDADMA or PAH, respectively), and polyanions (poly(styrenesulfonate), PSS). This is a general and powerful technique for the fabrication of thin carbon nanotube films of arbitrary composition and architecture and allows also an easy preparation of all-SWNT (SWNT/SWNT) multilayers. The multilayers were characterized with vis-near-IR spectroscopy, X-ray photoelectron spectroscopy (XPS), surface plasmon resonance (SPR) measurements, atomic force microscopy (AFM), and imaging ellipsometry. The charge compensation in multilayers is mainly intrinsic, which shows the electrostatic nature of the self-assembly process. The multilayer growth is linear after the initial layers, and in SWNT/polyelectrolyte films it can be greatly accelerated by increasing the ionic strength in the SWNT solution. However, SWNT/SWNT multilayers are much more inert to the effect of added electrolyte. In SWNT/SWNT multilayers, the adsorption results in the deposition of 1-3 theoretical nanotube monolayers per adsorbed layer, whereas the nominal SWNT layer thickness is 2-3 times higher in SWNT/polyelectrolyte films prepared with added electrolyte. AFM images show that the multilayers contain a random network of nanotube bundles lying on the surface. Flexible polyelectrolytes (e.g., PDADMA, PSS) probably surround the nanotubes and bind them together. On macroscopic scale, the surface roughness of the multilayers depends on the components and increases with the film thickness.     

Interaction and adhesion properties of polyelectrolyte multilayers

The growth, morphology, and interaction/adhesion properties of supported poly(sodium 4-styrenesulfonate)/poly(allylamine hydrochloride) (PSS/PAH) and DNA/PAH multilayers were investigated by means of surface plasmon resonance spectroscopy, atomic force microscope (AFM) imaging, and AFM-related force measurements. Multilayers were assembled on a prelayer of poly(ethylenimine) (PEI) both with and without drying. SPR results showed a linear growth of the assembly in the case of PSS/PAH multilayers and nonlinear growth for DNA/PAH multilayers. Measurements of forces acting between a bare glass sphere and a multilayer-coated surface indicated repulsive or attractive forces, depending on surface charge, which suggests that, on approach, electrostatic forces dominate. On separation, we observed large pull-off forces in the case of positively charged multilayers and weak pull-off forces in the case negatively charged multilayers. Multiple adhesions and plateau regions observed on separation were interpreted in terms of a bridging of multiple polymer chains between the glass particle and the multilayer and a stretching of the polyelectrolyte loops. The dependence of the pull-off force on the number of deposited layers shows regular oscillations.     

Hydrothermal-induced structure transformation of polyelectrolyte multilayers: from nanotubes to capsules

The assembled polyelectrolyte nanotubes composed of poly(styrenesulfonate) and poly(allylamine hydrochloride) multilayers by using the layer-by-layer assembly combined with the porous template method can be transformed into capsules by a high-temperature treatment. Scanning electron microscopy and confocal laser scanning microscopy images revealed the whole transition process. The structure transformation of polyelectrolyte multilayers after annealing can be initiated by the input of thermal energy which leads to a breakage of ion pairs between oppositely charged polyelectrolyte groups. The transition process from tubes to capsules is supposed to be driven by the Raleigh instability and leads to the generated polyelectrolyte capsules with different sizes.     

Tuning smart microgel swelling and responsive behavior through strong and weak polyelectrolyte pair assembly

The layer-by-layer (LbL) assembly of polyelectrolyte pairs on temperature and pH-sensitive cross-linked poly(N-isopropylacrylamide)-co-(methacrylic acid), poly(NIPAAm-co-MAA), microgels enabled a fine-tuning of the gel swelling and responsive behavior according to the mobility of the assembled polyelectrolyte (PE) pair and the composition of the outermost layer. Microbeads with well-defined morphology were initially prepared by synthesis in supercritical carbon dioxide. Upon LbL assembly of polyelectrolytes, interactions between the multilayers and the soft porous microgel led to differences in swelling and thermoresponsive behavior. For the weak PE pairs, namely poly(L-lysine)/poly(L-glutamic acid) and poly(allylamine hydrochloride)/poly(acrylic acid), polycation-terminated microgels were less swollen and more thermoresponsive than native microgel, whereas polyanion-terminated microgels were more swollen and not significantly responsive to temperature, in a quasi-reversible process with consecutive PE assembly. For the strong PE pair, poly(diallyldimethylammonium chloride)/poly(sodium styrene sulfonate), the differences among polycation and polyanion-terminated microgels are not sustained after the first PE bilayer due to extensive ionic cross-linking between the polyelectrolytes. The tendencies across the explored systems became less noteworthy in solutions with larger ionic strength due to overall charge shielding of the polyelectrolytes and microgel. ATR FT-IR studies correlated the swelling and responsive behavior after LbL assembly on the microgels with the extent of H-bonding and alternating charge distribution within the gel. Thus, the proposed LbL strategy may be a simple and flexible way to engineer smart microgels in terms of size, surface chemistry, overall charge and permeability.     

Pore assembled multilayers of charged polypeptides in microporous membranes for ion separation

In this study, highly permeable ion-selective membranes are prepared via immobilization of polyelectrolyte multilayer networks within the inner pore structure of a microporous (pore size = 0.2 microm) support. Electrostatic layer-by-layer assembly is achieved through alternate adsorption of cationic and anionic polyelectrolytes under convective flow conditions. To initiate pore assembly, the first layer consists of covalently bound charged polypeptides (poly(L-glutamic acid) (PLGA) or poly(L-lysine) (PLL)) establishing a charged support for subsequent adsorption. Nonstoichiometric immobilization of charged multilayers within a confined pore geometry leads to an enhanced volume density of ionizable groups in the membrane phase. This overall increase in the effective charge density allows for Donnan exclusion of ionic species (especially divalent co-ions) using microporous materials characterized by permeability values that exceed conventional membrane processes. Multilayer assemblies are fabricated using both PLGA/PLL and synthetic polyelectrolytes (poly(styrenesulfonate)/poly(allylamine)) in an attempt to compare the level of adsorption and separation properties of the resulting materials. The role of salt concentration in the carrier solvent on overall polyelectrolyte adsorption was examined to determine its effect on both solute (Cl-, SO4(2-), As(V)) and water transport. Constriction of the pore size induced by multilayer propagation was monitored through permeability measurements and dextran rejection studies at each stage of the deposition process.     

pH-sensitive bipolar ion-permselective ultrathin films

pH-Sensitive bipolar ion-permselective films of polyelectrolyte multilayers were prepared by layer-by-layer (LbL) assembly and photo-cross-linking of benzophenone-modified poly(acrylic acid) (PAA-BP) and poly(allylamine hydrochloride) (PAH-BP). The multilayer structure and ionizable group composition was finely tuned by changing the pH of the dipping solution. This structure and composition was in turn "preserved" by photo-cross-linking, forming highly stable membrane films. Since PAA-BP and PAH-BP are weak polyelectrolytes, it is possible to control the number of unbound, un-ionized -COOH or -NH2 groups in the multilayer by changing the pH. Moreover, the pH of the deposited film also plays an important role in determining selective latter permselectivity. For example, PAA-BP/PAH-BP multilayers deposited from two pH conditions, pH = 3 (PAA-BP) and pH = 6 (PAH-BP), showed pH-switchable permselectivity for both cationic (pH = 10) and anionic (pH = 3) probe molecules in a single film. The system offers advantages in film stability and introducing reversible selective ion permeability over previous multilayer film and cross-linking methods.     

Layer‐by‐layer assembly of weak‐strong copolymer polyelectrolytes: A route to morphological control of thin films

Multilayer films were assembled from a strong polyelectrolyte (poly(diallyldimethylammonium chloride), PDADMAC) and a copolymer containing both strongly charged styrene sulfonate moieties and weakly charged maleic acid moieties (poly(4‐styrenesulfonic acid‐co‐maleic acid), PSSMA). Growth of PSSMA/PDADMAC multilayers was linear, as characterized by UV‐vis spectroscopy and quartz crystal microgravimetry. The influence of both the pH of the PSSMA adsorption solutions and the ratio of SS:MA in the PSSMA on multilayer properties was investigated. Fourier transform infrared spectroscopy results showed that the ionization of carboxylic acid groups in PSSMA/PDADMAC multilayers did not vary significantly with changes in the PSSMA assembly pH. However, the multilayers showed different thicknesses, surface morphologies, and stability to post‐assembly pH treatment. We also demonstrate that PSSMA/PDADMAC multilayers are significantly more stable than PSSMA/PAH multilayers after post‐assembly pH treatment (i.e. the films remain intact when exposed to pH extremes). In addition, the surface morphology of two films (PSSMA 1:1 assembled at pH 5.8, post‐treated at pH 2 and PSSMA 3:1 assembled at pH 5.8, post‐treated at pH 11) changed significantly when the films were exposed to solutions of different pH and, in the former case, this change in film morphology was reversible. The porous morphology after treatment at pH 2 could be reversed to give a significantly smoother film after subsequent exposure to water for 24 h. Our results demonstrate that by the rational choice of the assembly pH of PSSMA, stable and pH‐responsive films can be obtained via the sequential assembly of PSSMA and PDADMAC. These films have potential in controlled release applications where film stability and pH‐responsive behavior are essential. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4341‐4351, 2007     

Polyelectrolyte spin assembly: Influence of ionic strength on the growth of multilayered thin films

Layer-by-layer (LbL) assembly of polymer electrolyte multilayers is now a well-established method for the fabrication of thin films by sequential adsorption of alternating layers of oppositely charged polyelectrolytes. Most commonly, such adsorptions have been from quiescent solutions of varying ionic strength and pH. Here, we report results on an alternative processing route for the achievement of polymeric multilayer assemblies of poly(sodium-4-styrene sulfonate) and poly(allylamine hydrochloride) that utilizes conventional spin coating. We investigated and describe herein the dependence of multilayer film buildup on solution ionic strength for comparison with similar dependence in quiescent adsorption. Using UV-Vis spectroscopy we monitored the growth of the multilayered films, while with Atomic Force Microscopy (AFM) we examined the surface features and measured coating thicknesses at different salt concentrations. AFM and UV-Vis data reveal two regimes of behavior with increasing salt: strong salt-dependence at low salt contents, and weak salt-dependence for high salt contents. To explain this observation, we introduce the relevance of the dimensionless group De = τ, the local Deborah Number, to the problem. As ionic strength increases, τ increases so that spin-assembly flow influences adsorbed conformation, and thus LbL growth rate. Our results indicate the ability to design and control polyelectrolyte multilayered structures prepared via spin assembly by varying solution properties that influence the conformation of deposited polymer chains. Additionally, our studies reveal the need for study of the fundamental mechanisms of polyelectrolyte adsorption within complex flow fields. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 3654–3666, 2004     

Molecular "wiring" enzymes in organized nanostructures

We report on the "molecular wiring" efficiency of glucose oxidase in organized self-assembled nanostructures comprised of enzyme layers alternating with layers of an osmium-derivatized poly(allylamine) cationic polyelectrolyte, acting as redox relays. Varying the relative position of the active enzyme layer in nanostructures alternating active enzyme and inactive apoenzyme we have demonstrated that the specific rate of bimolecular FADH(2) oxidation ("wiring efficiency") is limited by the diffusion-like electron hopping mechanism in the multilayers.     

Polymer-metal complexes in polyelectrolyte multilayer films as catalysts for oxidation of toluene

We report on the binding of metal ions (Me(2+); Co(2+) and Cu(2+)) with weak polyelectrolyte multilayers (PEMs), as well as on catalytic activity of PEM-Me(2+) films for oxidation of toluene. Using several types of PEM films constructed using branched polyethyleneimine (BPEI) or quaterinized poly-4-vinylpyridines (QPVPs) as polycations and poly(acrylic acid) (PAA) or poly(styrene sulfonate) (PSS) as polyanions, we found that binding of Co(2+) and Cu(2+) ions with a PEM matrix can occur both through coordination to polycationic amino groups and/or ionic binding to polyacid groups. The amount of metal ions loaded within the film increased linearly with film thickness and was strongly dependent on polyelectrolyte type, film assembly pH, and fraction of permanent charge in polymer chains. Among various PEM-Me(2+) systems, BPEI/PAA-Co(2+) films assembled at pH 8.5 show the best catalytic performance, probably because of the preservation of high mobility of Co(2+) ions coordinated to amino groups of BPEI in these films. With BPEI/PAA-Co(2+) films, we demonstrated that films were highly permeable to reagents and reaction products within hundreds of nanometers of the film bulk; i.e., film catalytic activity increased linearly with layer number up to 30 bilayers and slowed for thicker films.