乙烯-辛烯共聚物/淀粉共混体系的非等温结晶动力学(英文)

通过差示扫描量热仪(DSC)研究了乙烯-辛烯共聚物/淀粉共混体系的非等温结晶动力学,用Jeziorny和Ozawa方程描述了结晶动力学过程.共混物的结晶温度和结晶焓强烈依赖于淀粉含量和冷却速率.结果表明,随着冷却速率的增加,每个试样的结晶放热曲线均变宽,并向低温区移动.当温度一定高时,所有试样均具有较快的结晶速率. Jeniorzy方程可以较好地描述POE/淀粉共混物的非等温结晶模式,而Ozawa方程对于POE/淀粉共混体系不太适合.     

反式-/顺式-1,4-聚异戊二烯共混体系的结晶动力学

采用差示扫描量热(DSC)法对反式-/顺式-1,4-聚异戊二烯共混体系的等温及非等温结晶动力学进行了研究,分别采用Avrami方程和莫志深法对其动力学参数进行了解析.研究结果表明,在反式-/顺式-1,4-聚异戊二烯共混体系的等温及非等温结晶过程中,顺式-1,4-聚异戊二烯(CPI)组分的存在会降低反式-1,4-聚异戊二烯(TPI)组分的结晶速率;在等温结晶过程中,CPI组分会提高TPI组分自身的结晶度;而非等温结晶过程中,CPI则提高了共混物中β晶型的相对含量.     

PET/PEN/DBS共混物非等温结晶动力学研究

采用DSC方法, 用修正的Avrami, Ozawa, Ziabicki宏观动力学模型描述PET/PEN/DBS[PET: 聚对苯二甲酸乙二醇酯; PEN: 聚2,6-萘二甲酸乙二醇酯; DBS: 1,3∶2,4-二(亚苄基)-D山梨醇]共混物的非等温熔融结晶过程, 研究结果表明, 修正的Avrami模型能很好地描述此共混物非等温结晶过程. 冷却速率在5-20 ℃/min范围内, Ozawa方程能很好地描述初期结晶过程, 但结晶后期由于忽略次级结晶而不适宜. 由Ziabicki结晶动力学参数可知, 该共混物的结晶随着成核剂DBS含量的增加而降低, 结晶速率随着成核剂DBS含量的增加而提高. 在非等温结晶条件下, 共混物结晶同时受到冷却速率和共混物组成的影响, 与共混物非等温结晶过程的有效能垒分析结果基本一致.     

聚氧化乙烯(PEO)/聚双酚A羟基醚(PBHE)共混体系的非等温结晶动力学

本文联系Avrami方程和Ozawa方程,得出一个适合于非等温结晶动力学过程的新的基本方程,由这个方程可获得描述非等温结晶动力学过程的某些参数,并用DSC方法,对PEO/PBHE共混体系的非等温结晶动力学进行了研究,对实验结果进行了讨论.     

低密度聚乙烯/乙丙烯三元共聚(LDPE/EPO)共混体系的相容性及其结晶结构

DDV、DSC、WAXD、萃取和Raman光谱实验表明,在所有组成下,LDPE/EPO共混体系共晶相容.WAXD法测定表明,LDPE/EPO共混体系的结晶度随EPO组分含量的增加而降低,EPO未能进入LDPE晶胞中.     

电子束辐照法制备交联共混物聚(ε-己内酯)/苯乙烯-丙烯腈共聚物的结晶动力学研究

将线形聚(ε-己内酯)(PCL)、苯乙烯-丙烯腈共聚物(SAN)和三烯丙基异三聚氰酸酯(TAIC)熔融共混,通过电子束辐照法制备了3组凝胶含量不同的交联PCL和PCL/SAN共混物样品.采用相差显微镜(PCOM)观察发现PCL与SAN具有良好的相容性.利用示差扫描量热法(DSC)和偏光显微镜(POM)研究了交联PCL和PCL/SAN共混物的等温结晶动力学和非等温结晶行为.结果表明,当体系交联程度相近时,交联聚己内酯的结晶动力学随SAN含量的增加而明显减慢.在SAN含量相同时,交联聚己内酯的结晶速率随交联程度增大而减小.对分离提取的线形和交联组分进行结晶动力学的研究则表明SAN引入对PCL的结晶速率起到了关键性的抑制作用.     

SEBS-g-MAH对LLDPE结晶行为的影响

利用差示扫描量热法结合Avrami方程研究了线性低密度聚乙烯(LLDPE)、LLDPE与苯乙烯-乙烯-丁烯-苯乙烯嵌段共聚物(SEBS)共混体系及LLDPE与不同接枝率的SEBS共聚物接枝马来酸酐(SEBS-g-MAH)共混体系的非等温结晶动力学,探讨了SEBS-g-MAH对LLDPE结晶行为的影响.通过偏光显微镜(POM)观察了各体系的结晶形态.通过Gupta法、Jeziorny法和莫志深法分别对非等温结晶过程进行表征,结果显示:热塑性弹性体SEBS及其接枝物SEBS-g-MAH的加入阻碍了LLDPE分子链的规则排列,影响了链段在结晶扩散迁移过程中的规整排列速率,使得结晶速率变慢,对LLDPE晶体生长起了抑制作用.样品的Avrami指数均为1.1～1.5,说明LLDPE的结晶成核机理和生长方式没有改变.     

热塑性聚酰亚胺与聚醚醚酮共混物的等温结晶动力学

采用熔融共混方法制备了热塑性聚酰亚胺(TPI)与聚醚醚酮(PEEK)的共混物; 用示差扫描量热分析(DSC)研究了共混物的等温结晶动力学. 分别采用Avrami方程和Hoffman-Lauritzen方程分析共混物的等温结晶动力学、端表面自由能(σe)和分子链折叠功(q). 结果表明, 加入TPI后PEEK的结晶速率降低, 结晶活化能、σe和q均增加. 但这些数值的变化与TPI含量不呈线性关系, 并从共混物的相容性和表面形貌给出了可能的解释.     

苯乙烯-丙烯等规立构嵌段共聚物(iPS-b-iPP)的非等温结晶动力学的研究

用DSC法研究了苯乙烯-丙烯等规立构嵌段共聚物的非等温结晶动力学。结果表明:冷却速率在5～20℃/min范围内,共聚物的非等温结晶动力学参数能很好地符合Avrami动力学方程,非等温结晶速率常数与冷却速率有关,动力学结晶能力则同时受到冷却速率和共聚物组成比的影响。文中还讨论了在非等温结晶条件下共聚物的结晶成核和生长方式与共聚物组成和结构的关系。联合Avrami方程和Ozawa方程推导的非等温结晶动力学方程较好地描述了iPS-b-iPP嵌段共聚物的非等温结晶动力学过程。     

尼龙66/蒙脱土复合材料结晶行为的研究

在密炼机中采用熔融共混法制备蒙脱土重量分数为 2 5 %、4 5 %的尼龙 6 6 /蒙脱土复合材料 .通过DSC法对非等温结晶行为及在 2 2 8～ 2 4 0℃范围内的等温结晶行为进行研究 ,并与纯尼龙 6 6进行比较 .从其等温和非等温结晶行为的研究表明 ,蒙脱土起成核剂的作用 ,它的填入使尼龙 6 6结晶速率提高 ,但填料与基体间的相互作用使其链段运动困难 ,结晶活化能提高 ;在研究的填料含量变化范围内 ,结晶行为变化不大 ,并且找到该复合材料在 2 2 8～ 2 34℃范围结晶对温度的不敏感区 ;对非等温结晶过程分析 ,刘结平 莫志深方程是适用的 ,而Ozawa方程则是不适用的 .     

A comparative study on the single-scan and multiple-scan techniques in differential scanning calorimetry: Application to the crystallization of the semiconducting Ge0.13Sb0.23Se0.64 alloy

A method has been developed for analysing the evolution with time of the volume fraction transformed and for calculating the kinetic parameters at non-isothermal reactions in materials involving formation and growth of nuclei. By considering the assumptions of extended volume and random nucleation, a general expression of the fraction transformed as a function of time has been obtained in isothermal crystallization processes. Considering the mutual interference of regions growing from separate nuclei the Johnson–Mehl–Avrami equation has been deduced as a particular case. The application of the transformation rate equation to the non-isothermal processes has been carried out under the restriction of a nucleation which takes place early in the transformation and the nucleation frequency is zero thereafter. Under these conditions, the kinetic parameters have been deduced by using the techniques of data analysis of single-scan and multiple-scan. The theoretical method developed has been applied to the glass-crystal transformation kinetics of the semiconducting Ge_0.13Sb_0.23Se_0.64 alloy. The kinetic parameters obtained according to both techniques differ by only about 2.5%, which confirms the reliability and accuracy of the single-scan technique when calculating the above-mentioned parameters in non-isothermal transformation processes. The phases at which the above-mentioned semiconducting glass crystallizes after the thermal process have been identified by X-ray diffraction. The diffractogram of the transformed material shows that microcrystallites of Sb₂Se₃ and GeSe are associated with the crystallization process, remaining a residual amorphous matrix.     

低密度聚乙烯/乙丙烯三元共聚(LDPE/EPO)共混体系的相容性及其结晶结构

 DDV、DSC、WAXD、萃取和Raman光谱实验表明,在所有组成下,LDPE/EPO共混体系共晶相容.WAXD法测定表明,LDPE/EPO共混体系的结晶度随EPO组分含量的增加而降低,EPO未能进入LDPE晶胞中.     

一种研究聚合物非等温结晶动力学的方法

作者基于多年对聚合物结晶动力学方面研究的工作积累,联合Avrami方程和Ozawa方程,提出了一种研究聚合物非等温结晶动力学的新方法.该方法既克服了使用Ozawa方程所获得的数据点过少,常常出现非线性,不能获得可靠的动力学参数的缺点,又克服了使用经Jeziorny修正的Avrami方程所获得的表观Avrami指数无法准确预测非等温过程成核生长机理的缺点.该方法已成功用于多种聚合物体系,被国内外学者引用数百次,已成为研究聚合物非等温结晶动力学一种有效方法.     

Nucleation Activation and Spherical Crystals Morphology of LLDPE/LDPE/TiO2 Nanocomposites Prepared by Non-Isothermal Crystallization

The nucleation activation of TiO₂ nanoparticles in the linear low-density polyethylene (LLDPE)/low-density polyethylene (LDPE)/TiO₂ nanocomposites prepared by non-isothermal crystallization, the spherical crystals morphology of the etched LLDPE/LDPE and LLDPE/LDPE/TiO₂ composites were investigated by differential scanning calorimetry (DSC) and field-emission scanning electron microscopy (FE-SEM), respectively. The results showed that the heterogeneous nucleation activation of TiO₂ nanoparticles was accelerated by the fast cooling rate. The spherical crystals in the LLDPE/LDPE and LLDPE/LDPE/TiO₂ composites were ascribed to the same crystal structure. It was worth to note that there was distinct difference between the morphology of the cocrystallization LLDPE/LDPE crystals and that of the independent crystallization LLDPE/LDPE crystals.     

水性聚氨酯/功能化石墨烯纳米复合材料的非等温结晶动力学

采用差示扫描量热法DSC研究了水性聚氨酯/功能化石墨烯(WPU/FGNs)纳米复合材料的非等温结晶行为,分别采用Ozawa方程、莫志深方程研究复合材料的非等温结晶动力学,并通过Kissinger方程计算了结晶过程中的活化能。 结果表明,石墨烯在复合材料的结晶过程中起到异相成核剂的作用,提高了复合材料的结晶起始温度、峰值温度和结晶速率;增加石墨烯的质量分数,复合材料的结晶维数增加;石墨烯增加至0.3%,复合材料的活化能从-47.74 kJ/mol降低至-53.60 kJ/mol,继续增加石墨烯至1.0%,复合材料的活化能增加至-41.74 kJ/mol。     

Effect of Electron Beam Irradiation on the Kinetics of Non-isothermal Crystallization of Nylon 66

The non-isothermal crystallization kinetics was studied by differential scanning calorimetric analysis on nylon 66 and e-beam irradiated nylon 66 at different cooling rates. The Modified Avrami equation, the Ozawa equation and the Combined Avrami-Ozawa equation were applied to study the kinetics of non-isothermal crystallization of nylon 66. The crystallization behavior of pristine nylon 66 polymer was compared with that of e-beam irradiated nylon 66 and observed that the kinetics of non-isothermal crystallization of nylon66 was affected largely upon e-beam irradiation. E-beam irradiation not only decreased the crystallization temperature of nylon 66, but influenced the mechanism of nucleation and crystal growth and reduced the overall crystallization rate of nylon 66 also. The crystallization activation energy calculated by the Kissinger method for irradiated nylon 66 was lower than that of pristine nylon 66.