Toughening of poly(2,6-dimethyl-1,4-phenylene oxide)/nylon 6 alloys with functionalized elastomers via reactive compatibilization: morphology, mechanical properties, and rheology

Blends of poly(2,6-dimethyl-1,4-phenylene oxide)/nylon 6 alloys based on ethylene-propylene-diene elastomer (EPDM) grafted with maleic anhydride (MA) (EPDM-g-MA), EPDM grafted with glycidyl methacrylate (EPDM-g-GMA), and styrene-ethylene-butadiene-styrene block copolymer grafted with MA (SEBS-g-MA) were prepared via melt extruction, and morphology, mechanical properties, and rheology were studied. The compatibilizing effects of functionalized elastomers on the PPO/nylon 6 alloys were proved by DSC analysis and confirmed by the significant improvement in the notched Izod impact strength. Toughening was resulted from the smaller particle size and finer dispersion of EPDM in the PPO/nylon 6 matrix as well as a novel network structure of SEBS-g-MA domain in matrix. The notched Izod impact strength of the blends exhibited an optimum value when the extent of MA or GMA graft ratio of EPDM varied, which was an order of magnitude higher than the non-toughened alloys. The morphology revealed that the size of EPDM particles decreased with an increase in graft ratio of MA or GMA onto EPDM. Rheology investigation indicated that the MA or GMA moieties on EPDM reacted with the amine groups of nylon 6, which increased the molecular weight and the degree of branching, and thus resulted in an increase in the viscosity of the blends. This proved the reactive compatibilization between functionalized EPDM and PPO/nylon 6 matrix.     

Aminolysis kinetics of model and polymer-bound anhydride moieties in low- and high-viscosity media

This study examines the legitimacy of using the reaction kinetics of low molecular weight model compounds in solution to predict the chemical kinetics of polymer-bound species in a homogeneous melt. The reaction under study takes place between an aliphatic secondary amine, diisooctadecylamine (DiOA), and a 5-membered anhydride ring, saturated maleic anhydride (MA), forming an amic acid product. The MA species was present as a pendant graft on either a model compound, dodecane-g-(maleic anhydride) (dodecane-g-MA), or a polymer chain, linear low-density polyethylene-g-(maleic anhydride) (LLDPE-g-MA). Pseudo-second-order kinetics of the anhydride consumption are followed by infrared spectroscopy, either in situ in dodecane solution or by scanning frozen film samples taken from a linear low-density polyethylene melt. It was found that the LLDPE-g-MA/DiOA system reacted at a slightly slower rate than the dodecane-g-MA/DiOA system in the low-viscosity solution at 140°C. In the melt, the dodecane-g-MA/DiOA system experienced a small decrease in the overall reaction rate compared to the same reaction carried out in dodecane. However, the LLDPE-g-MA/DiOA system underwent a 65% decrease in the observed second-order rate constant on going from a solution to the melt. To explain these phenomena, the effects of diffusion, miscibility, and chain entanglements in the melt are examined here. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 1573–1582, 1998     

Effect of PPO‐g‐MA on structures and properties of PPO/PA6/short glass fiber composites

Poly(2,6‐dimethyl‐1,4‐phenylene oxide)/polyamide 6 (PPO/PA6) blends were reactively compatibilized by maleic anhydride (MA) grafted PPO (PPO‐g‐MA) and reinforced by short glass fibers (SGF) via melt extrusion. An observation of the SGF‐polymer interface by scanning electronic microscope (SEM) together with etching techniques indicated that the PPO‐g‐MA played a decisive role in the adhesion of polymers to SGF. The rheological behavior was investigated by capillary rheometer, and the addition of PPO‐g‐MA, and SGF could increase the viscosity of the PPO/PA6 blends. The analysis of fiber orientation and distribution in the PPO/PA6/SGF composites showed PPO‐g‐MA favored to the random dispersion of SGF. The statistic analysis of SGF length showed that PPO‐g‐MA was helpful to maintain the fiber length during melt‐processing. For the composites at a given SGF content of 30 wt %, the addition of PPO‐g‐MA increased the tensile strength from 59.4 MPa to 97.1 MPa and increased SGF efficiency factor from 0.028 to 0.132. The experimental data were consistent with the theoretical predictions of the extension of Kelly‐Tyson model for tensile strength. The fracture toughness of the composites was investigated by single edge notch three‐point bending test. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2188–2197, 2009     

Morphological,rheological, and mechanical properties of ethylene propylene diene monomer/carboxylated styrene-butadiene rubber/multiwall carbon nanotube nanocomposites

Abstract

A hybrid nanocomposite based on ethylene propylene diene monomer/carboxylated styrene-butadiene rubber (EPDM/XSBR) blend with different concentrations (0–7 phr) of multiwall carbon nanotube (MWCNT) was prepared on a two-roll mill. The role of grafted maleic anhydride (EPDM-g-MA) as compatibilizer and the effect of different concentrations of MWCNT on mechanical properties, morphology, rheological and curing characteristics of nanocomposites were investigated. The curing behavior of the prepared nanocomposites was studied using a rheometer. Also, the microstructure of nanocomposites was observed using TEM. By increasing the MWCNT concentration in the compatible blends, the curing time and scorch time of the blends decreased, while the maximum and minimum torque increased. Failure surface morphology studies showed that the existence of EPDM-g-MAH compatibilizer improved the distribution of MWCNT within the polymer matrix and uniform distribution of MWCNT with a small amount of aggregation was obtained. On the other hand, the presence of MWCNT in the matrix led to a sharper surface of the fracture. Also, mechanical properties such as modulus, tensile strength, hardness, fatigue, resilience and elongation-at-break for compatible EPDM/XSBR nanocomposite showed better results than those for incompatible composite.     

Reactive blending: inhomogeneous interface grafting in melts of maleinated polystyrene and polyamides

To be competitive, most blends need compatibilizers, usually copolymers with a blocky architecture, the chains of which cover the interfaces between the blend phases, refining the phase morphology and improving the interface strength. When the blend components are suitably functionalized, such copolymers can be conveniently generated in situ, in processes of reactive blending. Normally, graft copolymers are created. The polymer–polymer coupling proceeds exclusively in the interfaces. This interface grafting is (i) pivotal in the design of modern blend systems and (ii) an interesting route towards novel copolymers. The complex kinetics of interface grafting in blend melts have so far attracted little attention. In a model study, amino terminated polyamide 12 (PA) was grafted in the melt onto heavily maleinated polystyrene (SMA; S: styrene and MA: maleic anhydride). Anhydride and amino functions react at high temperatures fast and irreversibly by imide condensation. A series of SMA/PA blends differing in composition and PA chain lengths was investigated, with the aim of driving the grafting to high conversions so a pure graft copolymer SMAgPA would result, instead of an SMA/PA/SMAgPA blend. However, a pure copolymer was never obtained. The grafting remained incomplete, except with very short-chained PA and only at equal weight fractions of SMA and PA. More importantly, the SMA chains were never grafted evenly. Instead, “overgrafted” and “undergrafted” chains SMAgPA coexisted in one and the same product. It appears that the SMAgPA chains form an auto-inhibitory barrier in the interfaces that prevents random grafting. Grafting proceeds to high conversion only in SMA/PA blends with a co-continuous phase morphology where the interfaces are constantly torn apart and renewed, during melt blending, so the reaction is constantly reactivated. © 1998 John Wiley & Sons, Ltd.     

Effect of maleic anhydride‐grafted polytetrafluoroethylene on the tensile and tribological properties of blending polytetrafluoroethylene with polyamide‐6

Blending polytetrafluoroethylene (PTFE) to polyamide‐6 (PA6) with and without maleic anhydride‐grafted polytetrafluoroethylene (PTFE‐g‐MA) was produced in a corotating twin screw extruder, where PTFE acts as the polymer matrix and PA6 as the dispersed phase. The effect of PTFE‐g‐MA on the tensile properties and tribological propertiesof PTFE/PA6 polymer blends is studied. Results show that the structural stability and morphology of the blends were greatly improved by PTFE‐g‐PA6 grafted copolymers, which were formed by the in situ reaction of anhydride groups with the amino end groups of PA6 during reactive extrusion forming an imidic linkage. The presence of PTFE‐g‐PA6 in the PTFE continuous phase improves the interfacial adhesion, as a result of the creation of an interphase that was formed by the interaction between the formed PTFE‐g‐PA6 copolymer in situ and both phases. Compared with thePTFE/PA6 without PTFE‐g‐MA, the PTFE/PA6 with PTFE‐g‐MAhad the lowest friction coefficient and wear under given applied load and reciprocating sliding frequency. The interfacial compatibility of the composite prevented the rubbing‐off of PA6, accordingly improved the friction and wear properties of the composite. Copyright © 2009 John Wiley & Sons, Ltd.     

Effects of functionalized multiwalled carbon nanotubes on the morphologies and mechanical properties of PP/EVA blend

The maleic anhydride‐grafted multiwalled carbon nanotubes (MWCNTs‐g‐MA) have been introduced into polypropylene/ethylene‐co‐vinyl acetate (PP/EVA) blend. To clearly describe the effects of MWCNTs‐g‐MA on the morphology and mechanical properties of PP/EVA blends, the selective distribution of MWCNTs‐g‐MA in the blends is realized through different sample preparation methods, namely, MWCNTs‐g‐MA disperse in EVA phase and MWCNTs‐g‐MA disperse in PP matrix. The results show that the distribution of MWCNTs‐g‐MA has an important effect on the final morphology of EVA and the crystallization structure of PP matrix. Compared with PP/EVA binary blend, distribution of MWCNTs‐g‐MA in PP matrix induces the aggregation of EVA phase at high EVA content and the decrease of spherulite diameters of PP matrix simultaneously. However, when MWCNTs‐g‐MA are dispersed in the EVA phase, they induce more homogeneous distribution of EVA, and the crystallization behavior of PP is slightly affected by MWCNTs‐g‐MA. The corresponding mechanical properties including impact strength and tensile strength are tested and analyzed in the work. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1481–1491, 2009     

Molecular dynamics and mechanical properties correlations of PA6/PPO blends compatibilized with SMA

The effects of the compatibilizer, styrene maleic anhydride (SMA‐8% MA) upon the change of morphology and molecular dynamics of polyamide‐6 (PA6) and poly (2,6‐dimethyl‐1,4‐phenylene oxide) (PPO) blends were investigated by means of solid‐state NMR techniques. With increasing amounts of SMA, the domains correspond to PA6 and PPO are reduced and the polymer segmental mobility increased. The correlation between NMR relaxation time, T, and the bulk mechanical properties provide a molecular level understanding of the modification of molecular dynamics by the compatibilizer (SMA). The correlation shows that the tensile strength is governed mainly by the morphology, but modulated by the PA6 crystallinity, while the tensile elongation and impact strength are closely affected by both the molecular mobility and morphology. The annealing process improved only the tensile strength, but deteriorated tensile elongation and impact strength due to the increase of PA6 crystallinity, which induced phase separation after annealing. This study raised an important point that the polymer mechanical properties are most sensitive to the molecular structure and dynamics take place within the range of 20 Å to few hundred Å. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1155–1163, 1999     

Synthesis of maleic anhydride grafted polyethylene and polypropylene,with controlled molecular structures

This article discusses a new chemical route to prepare maleic anhydride (MA) grafted polyethylene and polypropylene polymers with controlled molecular structure, that is, MA grafted content and polymer molecular weight and composition distributions. The chemistry involves a free radical graft reaction of maleic anhydride with poly(ethylene‐co‐p‐methylstyrene) and poly(propylene‐co‐p‐methylstyrene) copolymers. Under a suspension reaction condition, the grafting reaction takes place selectively on the p‐methylstyrene units in the copolymer, due to high reactivity of p‐methyl group and favorable mixing between p‐methylstyrene units and chemical reagents in the swollen amorphous phases. The resulting polymer shows no detectable molecular weight change during the reaction, and the MA grafted content increases with the increase of initiator and p‐methylstyrene concentrations. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1337–1343, 2000     

A study on melt grafting of maleic anhydride onto low‐density polyethylene and its blend with polyamide 6

Graft copolymerization of low‐density polyethylene (LDPE) with a maleic anhydride (MAH) was performed using intermeshing corotating twin‐screw extruder in the presence of benzoyl peroxide (BPO). The LDPE/polyamide 6 (PA6) and LDPE‐g‐MAH/PA6 blends were prepared in a corotating twin‐screw extruder. The melt viscosity of the grafted LDPE was measured by a capillary rheometer. The grafted copolymer was characterized by Fourier transform infrared spectroscopy (FTIR) and scanning electron microcopy (SEM). The influence of the variation in temperature, BPO and MAH concentration, and temperature on the grafting degree and on the melt viscosity was studied. The grafting degree increased appreciably up to about 0.45 phr and then decreased continuously with an increasing BPO concentration. According to the FTIR analysis, it was found that the amount of grafted MAH on the LDPE chains was ～5.1%. Thermal analysis showed that melting temperature of the graft copolymers decreases with increasing grafting degree. In addition to this, loss modulus (E″) of the copolymers first increased little with increasing grafting and then obviously decreased with increasing grafting degree. Furthermore, the results revealed that the tensile strength of the blends increased linearly with increasing PA6 content. The results of SEM and mechanical test showed that the blends have good interfacial adhesion and good stability of the phase structure, which is reflected in the mechanical properties. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 267–275, 2010     

Increased covalent conjugation of a model antigen to poly(lactic acid)-g-maleic anhydride nanoparticles compared to bare poly(lactic acid) nanoparticles

Maleic anhydride (MA) grafted poly(lactic acid) (PLA) (PLA-g-MA) was synthesized from PLA. Proton nuclear magnetic resonance confirmed the grafting of the MA. PLA-g-MA and PLA were used to prepare polymeric nanoparticles. Particle size distributions were measured by dynamic light scattering, and colloidal stability was determined by (zeta) ζ-potential. The ζ-potential becomes more negative for PLA-g-MA than PLA nanoparticle dispersions, due to the presence of deprotonated carboxylic acid groups on the backbone of the PLA and confirms the MA grafting results. Maleic anhydride grafted on PLA backbone improves the covalent conjugation with ovalbumin (OVA) compared to OVA physically adsorbed on the particles. The chemical conjugation was carried out via amide linkages between the carboxylic groups of the nanoparticles, activated with 1-ethyl-3-(3-dimethylaminopropyl)carbodiimide, and the amino groups of the protein. The amount of protein conjugated was measured by using the bicinchoninic acid method and is threefold higher compared to the adsorbed OVA. Moreover, the PLA-g-MA nanoparticles increased the amount of conjugated OVA by 36 wt% compared to PLA nanoparticles. OVA adsorption and OVA conjugation provided colloidal dispersions with excellent stability.     

Thermal studies on polypropylene/polyamide‐6 blends modified by succinic anhydride and succinyl fluorescein grafted polypropylenes

This study investigates the role played by two different interface agents on the basis of atactic polypropylene in the continuous/disperse phase polypropylene/polyamide‐6 (PP/PA6) system. The two agents used were obtained at the authors' laboratories from an atactic polypropylene byproduct derived from industrial polymerization reactors and consist of two grafted polymers containing either succinic anhydride (a‐PP‐SA) or both succinyl‐fluorescein and succinic anhydride grafted groups (a‐PP‐SF/SA). The role of these grafted polymers as compatibilizers in PP/PA6 polymer blends has been confirmed in previous investigations on the basis of their macroscopic behavior. This work investigates the thermal study of these blends where polypropylene acts as the polymer matrix and polyamide as the dispersed phase. Under isothermal conditions, thermal analysis agrees with the changes in the overall system behavior caused by the presence of the interface agents. These aspects were confirmed by polarized light microscopy that showed the morphology of the blends before and after modification with a‐PP‐SA or a‐PP‐SF/SA. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1307–1315, 2002     

Melt processing of maleic anhydride grafted poly(lactic acid) and its compatibilizing effect on poly(lactic acid)/poly(butylene adipate-<Emphasis Type="Italic">co</Emphasis>-terephthalate) blend and their composite

Poly(lactic acid) (PLA)/poly(butylene adipate-co-terephthalate) (PBAT) blends were prepared using melt processing. The effects of maleic anhydride grafted PLA (PLA-g-MA) and calcium carbonate (CaCO₃) content on mechanical, thermal, and morphological properties of the blends were investigated. PLA-g-MA was synthesized by varying monomer and initiator contents using a reactive melt-grafting process. Tensile properties of PLA/PBAT blend were enhanced with adding 2 phr of PLA-g-MA. SEM micrographs exhibited the improvement of interfacial adhesion between PLA and PBAT in the compatibilized blend. Moreover, thermal stability of the blends improved with presence of PLA-g-MA. With increasing CaCO₃ content, Young’s modulus of the composites increased.     

PLA maleation: an easy and effective method to modify the properties of PLA/PCL immiscible blends

In this study, maleic-anhydride-grafted polylactide (PLA-g-MA) was investigated as a potential compatibilizing agent for the polylactide (PLA)/poly(ε-caprolactone) (PCL) system, with the aim of enhancing the final properties of the two polymer blends. Indeed, PLA-g-MA was prepared via reactive blending through a free radical process and characterized by means of ¹H-NMR and titration measurements, which demonstrated that the employed procedure allows grafting 0.7 wt% of MA onto the polymer backbone, while avoiding a dramatic reduction of PLA molecular mass. The specific effect of the MA-grafted PLA on the features of the PLA/PCL system was highlighted by adding different amounts of PLA-g-MA to 70:30 (w/w) PLA/PCL blends, where the 70 % PLA component was progressively substituted by its maleated modification. The efficiency of PLA-g-MA as a compatibilizer for the PLA/PCL blends was assessed through SEM analysis, which showed that the dimensions of PCL domains decrease and their adhesion to PLA improves by increasing the amount of PLA-g-MA in the blends. The peculiar microstructure promoted by the presence of PLA-g-MA was found to enhance the mechanical properties of the blend, improving the elongation at break without decreasing its Young’s modulus. Our study demonstrated that not only the microstructure but also the thermal properties of the blends were significantly affected by the replacement of PLA with PLA-g-MA.     

Interplay between bulk viscoelasticity and surface energy in autohesive tack of rubber‐tackifier blends

The effects of change in surface energy and bulk viscoelastic properties on the autohesive tack strength of brominated isobutylene‐co‐p‐methylstyrene (BIMS) rubber have been investigated by the addition of hydrocarbon resin (HCR) tackifier and maleated hydrocarbon resin (MA‐g‐HCR) tackifier. The addition of compatible HCR tackifier results in a reasonable increment in the tack strength of BIMS rubber by modifying only the bulk viscoelastic properties (compliance, entanglement molecular weight, relaxation time, self‐diffusion, and monomer friction coefficient values) of BIMS rubber to perform better during the course of bonding and debonding steps of the peel test. Incorporation of MA‐g‐HCR tackifier (containing 5–20 wt % of grafted maleic anhydride) steadily increases the tack strength of BIMS rubber further by precisely modifying both the surface energy and bulk viscoelastic properties to perform much better in the bonding and debonding steps. However, beyond 20 wt % of grafted maleic anhydride in the HCR tackifier, the tack strength starts decreasing due to the incompatibility between the blend components, and hence, the bulk viscoelastic properties required for bond formation are severely retarded by the interrelated reinforcing effect and the phase separation effect of the brittle MA‐g‐HCR tackifier in the BIMS rubber. Hence, the polar groups in a tackifier will contribute to significant enhancement of autohesive tack strength only if the bulk viscoelastic property of the rubber‐tackifier blend is favorable for bond formation and bond separation. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 972–982, 2010     

Controlled migration of antifog additives from LLDPE compatibilized with LLDPE grafted maleic anhydride

This paper summarizes a study of controlled migration of an antifog (AF) additive; sorbitan monooleate (SMO), from linear low density polyethylene (LLDPE) films containing a compatibilizer, LLDPE grafted maleic anhydride (LLDPE‐g‐MA). LLDPE/LLDPE‐g‐MA/SMO blends were prepared by melt compounding. Bulk and surface properties of compression molded LLDPE films containing SMO and LLDPE‐g‐MA were characterized using Fourier transform infrared spectroscopy and contact angle measurements. Thermal properties were investigated using a thermal gravimetric analyzer. Diffusion coefficient (D) was calculated, and AF properties were characterized using a “hot fog” test. Compression molded films were characterized for their morphology using high‐resolution scanning electron microscopy, and rheological properties were measured using a parallel‐plate rotational rheometer. It was found that the LLDPE/LLDPE‐g‐MA/SMO systems are characterized by a slower SMO migration rate, a lower diffusion coefficient, and lower contact angle values compared with LLDPE/SMO blends. These results are well correlated with results of a hot fog test. Morphological studies revealed a very fine dispersion of SMO in the LLDPE films, when 3 phr LLDPE‐g‐MA was combined with 1 phr SMO. Thermal analysis results show that the incorporation of 3 phr LLDPE‐g‐MA and 1 phr SMO significantly increases the decomposition temperature of the blend at T > 400°C. At high shear rates, the LLDPE blends show that the AF and the compatibilizer have a lubrication effect on LLDPE. Copyright © 2014 John Wiley & Sons, Ltd.     

The influence of partial emulsification on coalescence suppression and interfacial tension reduction in PP/PET blends

This study examines how the relative role of coalescence suppression and interfacial tension reduction influence the particle size at various levels of in situ compatibilization. The polymers studied are polyethylene terephthalate (PET) as matrix and a polypropylene (PP) as dispersed phase compatibilized by a triblock copolymer of poly(styrene–hydrogenated butadiene–styrene) (SEBS) grafted with maleic anhydride. The interfacial tension was studied by the breaking‐thread method, and it was used along with the morphology to characterize the emulsification efficacy of the copolymers. By modifying the concentration of MA grafted on the SEBS, different levels of emulsification of the blends were obtained. A comparison of 1/99 and 10/90 PP/PET blends compatibilized by SEBS‐g‐MA allows one to distinguish the relative role of interfacial tension and coalescence suppression in diminishing particle size. It is shown that varying degrees of residual coalescence remain, depending on the level of %MA in the copolymer. A detailed study of the 2%MA system below interfacial saturation was carried out to shed further light on the dependence of coalescence suppression on emulsification level and interfacial coverage. After separating out the contribution of interfacial tension on particle size reduction, it is shown that coalescence suppression for this system increases gradually with areal density of modifier at the interface right up to the region of interfacial saturation. Finally, the interfacial and morphological data were used to test the ability of the Lee and Park model to describe coalescence in polymer blends. Reasonable agreement was found between the parameter c₁, describing the coalescence in that model, and the trends related to residual coalescence from this study. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 939–951, 1999     

The relative role of coalescence and interfacial tension in controlling dispersed phase size reduction during the compatibilization of polyethylene terephthalate/polypropylene blends

The breaking thread and the sessile drop methods have been used to evaluate the interfacial tension between a polypropylene (PP) and a polyethylene-terephthalate (PET). An excellent correlation was found between the two. The breaking thread technique was then used to evaluate the interfacial tension of these blends at various levels of a styrene-ethylene butylene-styrene grafted with maleic anhydride (SEBS-g-MA) compatibilizer. In order to evaluate the relative roles of coalescence and interfacial tension in controlling dispersed phase size reduction during compatibilization, the morphology of PP/PET 1/99 and 10/90 blends compatibilized by a SEBS-g-MA were studied and compared. The samples were prepared in a Brabender mixer. For the 10/90 blend, the addition of the compatibilizer leads to a typical emulsification curve, and a decrease in dispersed phase size of 3.4 times is observed. For the 1/99 blend, a 1.7 times reduction in particle size is observed. In the latter case, this decrease can only be attributed to the decrease of the interfacial tension. It is evident from these results that the drop in particle size for the 10/90 PP/PET blend after compatibilization is almost equally due to diminished coalescence and interfacial tension reduction. These results were corroborated with the interfacial tension data in the presence of the copolymer. A direct relationship between the drop in dispersed phase size for the 1/99 PP/PET blend and the interfacial tension reduction was found for this predominantly shear mixing device. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2271–2280, 1997     

Compatibilizing effect of isocyanate functional group on polyethylene terephthalate/low density polyethylene blends

To evaluate the compatibilizing effects of isocyanate (NCO) functional group on the polyethylene terephthalate/low density polyethylene (PET/LDPE) blends, LDPE grafted with 2-hydroxyethyl methacrylate-isophorone diisocyanate (LDPE-g-HI) was prepared and blended with PET. The chemical reaction occurred during the melt blending in the PET/LDPE-g-HI blends was confirmed by the result of IR spectra. In the light of the blend morphology, the dispersions of the PET/LDPE-g-HI blends were very fine over the PET/LDPE blends. DSC thermograms indicated that PET microdispersions produced by the slow cooling of the PET/LDPE-g-HI blends were largely amorphous, with low crystallinity, due to the chemical bonding. The tensile strengths of the PET/LDPE-g-HI blends were higher than those of the PET/LDPE blends having a poor adhesion. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 447–453, 1998     

Reactive functionalization of poly(lactic acid), PLA: Effects of the reactive modifier,initiator and processing conditions on the final grafted maleic anhydride content and molecular weight of PLA

A response surface methodology (RSM) design was used to analyze the effects of maleic anhydride (MA) and 2,5-bis(tert-butylperoxy)-2,5-dimethyl hexane (Luperox or L101) content, and TSE screw speed on the degree of grafted MA (MA_g) and number average molecular weight (M_n) of maleated PLA (PLA-g-MA), which can be used as a reactive compatibilizer in production of PLA blends with various components. PLA-g-MA's FTIR peaks indicated that MA was grafted onto the PLA backbone and oligomeric MA was also present. A maximum of 0.52 wt% MA_g determined by titration was achieved at the expense of a 50% reduction of M_n and an increase in the polydispersity index to around 2.0. Generally, increasing L101 increased the degree of grafting and decreased M_n. L101 and MA_g had a large effect on the stability of PLA-g-MA's M_n during storage. Nominally, amounts of MA equal to 4.5 wt%, L101 between 0.45 and 0.65 wt%, and screw speed of 20 rpm provided the optimal conditions for grafting MA onto PLA.