Effects of solid polymer electrolyte coating on the composition and morphology of the solid electrolyte interphase on Sn anodes

In order to discuss the effect of polymer coating layer on the Sn anode, the composition and morphology of the solid electrolyte interphase (SEI) film on the surface of Sn and Sn@PEO anode materials have been investigated. Compared with the bare cycled Sn electrode, the SEI on the surface of cycled Sn@PEO electrode is thinner, smoother, and more stable. Therefore, the Sn@PEO nanoparticles can basically keep the original appearance during cycling. Based on the results obtained from X-ray photoelectron spectroscopy (XPS), the SEI formed on the Sn@PEO electrode is characterized by inorganic components (Li₂CO₃)-rich outer layer and organic components-rich inner which could make the SEI more stable and inhibit the electrolyte immerging into the active materials. In particular, the elastic ion-conductive polyethylene oxide (PEO) coating could increase the toughness of SEI and allow the SEI to endure the stress variation in repetitive lithium insertion and extraction process. As a result, the Sn@PEO electrodes show significantly better capacity retention than bare Sn electrodes. The findings can serve as the theoretical foundation for the design of lithium-ion battery electrode with high energy density and long cycle life.     

原位聚合表面修饰的金属锂负极

金属锂负极由于比容量高(3860 mAh·g^-1)及氧化还原电位极低(-3.04 V vs.标准氢气电极(SHE)),被认为是实现高能量密度锂电池的理想负极。然而,金属锂电极与电解液反应剧烈,且锂离子在电极表面沉积不均匀容易产生枝晶,导致其循环稳定性和安全性都较差,限制了其应用推广。我们前期通过构建金属锂-碳纳米管(Li-CNT)复合结构,极大的提高了金属锂的比表面积,降低了电极电流密度,从而有效地抑制了锂枝晶的生长,提高了金属锂电极的循环稳定性和安全性能。本工作在前期工作基础上,采用简单的液相反应,利用4-氟苯乙烯(FPS)对Li-CNT进行表面修饰并进行原位聚合,得到了表面富含氟化锂(Li F)保护层的Li-CNT(FPS-Li-CNT)。该表面修饰层能够有效抑制电解液和空气对Li-CNT的侵蚀,显著的提高了LiCNT电极的界面稳定性。FPS-Li-CNT与磷酸铁锂正极(LFP)组成的LFP||FPS-Li-CNT全电池,在正负极容量配比为1:6条件下,能够稳定循环280圈,库伦效率达到97.7%。     

Anchoring an Artificial Solid–Electrolyte Interphase Layer on a 3D Current Collector for High‐Performance Lithium Anodes

The application of Li anodes is hindered by dendrite growth and side reactions between Li and electrolyte, despite its high capacity and low potential. A simple approach for this challenge is now demonstrated. In our strategy, the garnet‐type Li_6.4La₃Zr_1.4Ta_0.6O₁₂ (LLZTO)‐based artificial solid–electrolyte interphase (SEI) is anchored on Cu foam by sintering the Cu foam coated with LLZTO particles. The heat treatment leads to the interdiffusion of Cu and Ta₂O₅ at the Cu/LLZTO interface, through which LLZTO layer is fixed on Cu foam. 3D structure lowers the current density, and meanwhile the SEI reduces the contact of Li and electrolyte. Furthermore, the anchoring construction can endure Li‐deposition‐induced volume change. Therefore, LLZTO‐modified Cu foam shows much improved Li plating/stripping performance, including long lifespan (2400 h), high rate (maximum current density of 20 mA cm^?2), high areal capacity (8 mA h cm^?2 for 100 cycles), and high efficiency (over 98 %).     

Designing Solid Electrolyte Interfaces towards Homogeneous Na Deposition: Theoretical Guidelines for Electrolyte Additives and Superior High-Rate Cycling Stability

Metallic Na is a promising metal anode for large-scale energy storage. Nevertheless, unstable solid electrolyte interphase (SEI) and uncontrollable Na dendrite growth lead to disastrous short circuit and poor cycle life. Through phase field and ab initio molecular dynamics simulation, we first predict that the sodium bromide (NaBr) with the lowest Na ion diffusion energy barrier among sodium halogen compounds (NaX, X=F, Cl, Br, I) is the ideal SEI composition to induce the spherical Na deposition for suppressing dendrite growth. Then, 1,2-dibromobenzene (1,2-DBB) additive is introduced into the common fluoroethylene carbonate-based carbonate electrolyte (the corresponding SEI has high mechanical stability) to construct a desirable NaBr-rich stable SEI layer. When the Na||Na₃V₂(PO₄)₃ cell utilizes the electrolyte with 1,2-DBB additive, an extraordinary capacity retention of 94 % is achieved after 2000 cycles at a high rate of 10 C. This study provides a design philosophy for dendrite-free Na metal anode and can be expanded to other metal anodes.     

Ultrathin CuF2-Rich Solid-Electrolyte Interphase Induced by Cation-Tailored Double Electrical Layer toward Durable Sodium Storage

Solid-electrolyte interphase (SEI) seriously affects battery's cycling life, especially for high-capacity anode due to excessive electrolyte decomposition from particle fracture. Herein, we report an ultrathin SEI (3–4 nm) induced by Cu⁺-tailored double electrical layer (EDL) to suppress electrolyte consumption and enhance cycling stability of CuS anode in sodium-ion batteries. Unique EDL with SO₃CF₃-Cu complex absorbing on CuS in NaSO₃CF₃/diglyme electrolyte is demonstrated by in situ surface-enhanced Raman, Cyro-TEM and theoretical calculation, in which SO₃CF₃-Cu could be reduced to CuF₂-rich SEI. Dispersed CuF₂ and F-containing compound can provide good interfacial contact for formation of ultrathin and stable SEI film to minimize electrolyte consumption and reduce activation energy of Na⁺ transport. As a result, the modified CuS delivers high capacity of 402.8 mAh g⁻¹ after 7000 cycles without capacity decay. The insights of SEI construction pave a way for high-stability electrode.     

Fluoroethylene Carbonate Enabling a Robust LiF‐rich Solid Electrolyte Interphase to Enhance the Stability of the MoS2 Anode for Lithium‐Ion Storage

As a high‐capacity anode for lithium‐ion batteries (LIBs), MoS₂ suffers from short lifespan that is due in part to its unstable solid electrolyte interphase (SEI). The cycle life of MoS₂ can be greatly extended by manipulating the SEI with a fluoroethylene carbonate (FEC) additive. The capacity of MoS₂ in the electrolyte with 10 wt % FEC stabilizes at about 770 mAh g^?1 for 200 cycles at 1 A g^?1, which far surpasses the FEC‐free counterpart (ca. 40 mAh g^?1 after 150 cycles). The presence of FEC enables a robust LiF‐rich SEI that can effectively inhibit the continual electrolyte decomposition. A full cell with a LiNi_0.5Co_0.3Mn_0.2O₂ cathode also gains improved performance in the FEC‐containing electrolyte. These findings reveal the importance of controlling SEI formation on MoS₂ toward promoted lithium storage, opening a new avenue for developing metal sulfides as high‐capacity electrodes for LIBs.     

Anion receptor for enhanced thermal stability of the graphite anode interface in a Li-ion battery

The thermal stability of the solid electrolyte interphase (SEI) formed on a graphite anode has been enhanced by adding an anion receptor, tris(pentafluorophenyl)borane (TPFPB), to the electrolyte. The investigated electrolyte was LiBF₄ in a 2:1 mixture of ethylene carbonate (EC) and diethyl carbonate (DEC). Two concentrations of TPFPB have been investigated, 0.2 and 0.8 M. Galvanostatic cycling and differential scanning calorimetry (DSC) were used to study the effect of TPFPB on the electrochemical performance and thermal stability of graphite anodes. The best performance is obtained for a graphite anode cycled in an electrolyte with 0.2 M TPFPB: cyclability is improved, and the onset temperature for the first thermally activated reaction is increased by more than 60 °C up to 140–160 °C. X-ray photoelectron spectroscopy (XPS) has been used to examine the composition of the SEI formed in the different electrolytes; the improved performance for the graphite cycled with 0.2 M TPFPB is attributed to a reduced amount of LiF in the SEI.     

Bio-Inspired Polyanionic Electrolytes for Highly Stable Zinc-Ion Batteries

For zinc-ion batteries (ZIBs), the non-uniform Zn plating/stripping results in a high polarization and low Coulombic efficiency (CE), hindering the large-scale application of ZIBs. Here, inspired by biomass seaweed plants, an anionic polyelectrolyte alginate acid (SA) was used to initiate the in situ formation of the high-performance solid electrolyte interphase (SEI) layer on the Zn anode. Attribute to the anionic groups of −COO⁻, the affinity of Zn²⁺ ions to alginate acid induces a well-aligned accelerating channel for uniform plating. This SEI regulates the desolvation structure of Zn²⁺ and facilitates the formation of compact Zn (002) crystal planes. Even under high depth of discharge conditions (DOD), the SA-coated Zn anode still maintains a stable Zn stripping/plating behavior with a low potential difference (0.114 V). According to the classical nucleation theory, the nucleation energy for SA-coated Zn is 97 % less than that of bare Zn, resulting in a faster nucleation rate. The Zn||Cu cell assembled with the SA-coated electrode exhibits an outstanding average CE of 99.8 % over 1,400 cycles. The design is successfully demonstrated in pouch cells, where the SA-coated Zn exhibits capacity retention of 96.9 % compared to 59.1 % for bare Zn anode, even under the high cathode mass loading (>10 mg/cm²).     

Solid-Electrolyte Interphase Chemistries Towards High-Performance Aqueous Zinc Metal Batteries

Aqueous zinc metal batteries (AZMBs) are deemed a promising technology for electrochemical energy storage due to their high safety, low cost, and high energy density. However, AZMBs still suffer from severe side reactions, including Zn dendrite formation and intrinsic hydrogen evolution reaction. In contrast to the solid-electrolyte interphase (SEI) layer that stabilizes Li/Na/K metal anodes in organic electrolytes, it is difficult to form an SEI layer on the Zn surface because of the difficulty in decomposing the salt anions within the narrow electrochemical potential window of water. A team from the University of Adelaide reports a novel pure or hybrid electrolyte with H₂O by using dimethyl methylphosphonate (DMMP) as solvent or co-solvent to construct a uniform and stable phosphate-based SEI layer (ZnP₂O₆ and Zn₃(PO₄)₂). As a result, high Coulombic efficiencies and improved capacity retentions are obtained.     

Revealing Capacity Degradation of Ge Anodes in Lithium-Ion Batteries Triggered by Interfacial LiH

The Germanium (Ge), as a fast-charging and high specific capacity (1568 mAh g⁻¹) alloy anode, is greatly hampered in practical application by poor cyclability. To date, the understanding of cycling performance degradation remains elusive. This study illustrates that, contrary to conventional beliefs, most of the Ge material in failed anodes still retains good integrity and does not undergo severe pulverization. It is revealed that capacity degradation is clearly correlated to the interfacial evolution of lithium hydride (LiH). Tetralithium germanium hydride (Li₄Ge₂H), as a new species derived from LiH, is identified as the culprit of Ge anode degradation, which is the dominant crystalized component in an ever-growing and ever-insulating interphase. The significantly increased thickness of the solid electrolyte interface (SEI) is accompanied by the accumulation of insulating Li₄Ge₂H upon cycling, which severely retards the charge transport process and ultimately triggers the anode failure. We believe that the comprehensive understanding of the failure mechanism presented in this study is of great significance to promoting the design and development of alloy anode for the next generation of lithium-ion batteries.     

The understanding of solid electrolyte interface (SEI) formation and mechanism as the effect of flouro-o-phenylenedimaleimaide (F-MI) additive on lithium-ion battery

Solid electrolyte interface (SEI) is a critical factor that influences battery performance. SEI layer is formed by the decomposition of organic and inorganic compounds after the first cycle. This study investigates SEI formation as a product of electrolyte decomposition by the presence of flouro-o-phenylenedimaleimaide (F-MI) additive. The presence of fluorine on the maleimide-based additive can increase storage capacity and reversible discharge capacity due to high electronegativity and high electron-withdrawing group. The electrolyte containing 0.1 wt% of F-MI-based additive can trigger the formation of SEI, which could suppress the decomposition of remaining electrolyte. The reduction potential was 2.35 to 2.21 V vs Li/Li⁺ as examined by cyclic voltammetry (CV). The mesocarbon microbeads (MCMB) cell with F-MI additive showed the lowest SEI resistance (Rsei) at 5898 Ω as evaluated by the electrochemical impedance spectroscopy (EIS). The morphology and element analysis on the negative electrode after the first charge-discharge cycle were examined by scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), and X-ray photoelectron spectroscopy (XPS). XPS result showed that MCMB cell with F-MI additive provides a higher intensity of organic compounds (RCH₂OCO₂Li) and thinner SEI than MCMB cell without an additive that provides a higher intensity of inorganic compound (Li₂CO₃ and Li₂O), which leads to the performance decay. It is concluded that attaching the fluorine functional group on the maleimide-based additive forms the ideal SEI formation for lithium-ion battery.     

A Sustainable Solid Electrolyte Interphase for High-Energy-Density Lithium Metal Batteries Under Practical Conditions

High-energy-density Li metal batteries suffer from a short lifespan under practical conditions, such as limited lithium, high loading cathode, and lean electrolytes, owing to the absence of appropriate solid electrolyte interphase (SEI). Herein, a sustainable SEI was designed rationally by combining fluorinated co-solvents with sustained-release additives for practical challenges. The intrinsic uniformity of SEI and the constant supplements of building blocks of SEI jointly afford to sustainable SEI. Specific spatial distributions and abundant heterogeneous grain boundaries of LiF, LiN_xO_y, and Li₂O effectively regulate uniformity of Li deposition. In a Li metal battery with an ultrathin Li anode (33 μm), a high-loading LiNi_0.5Co_0.2Mn_0.3O₂ cathode (4.4 mAh cm⁻²), and lean electrolytes (6.1 g Ah⁻¹), 83 % of initial capacity retains after 150 cycles. A pouch cell (3.5 Ah) demonstrated a specific energy of 340 Wh kg⁻¹ for 60 cycles with lean electrolytes (2.3 g Ah⁻¹).     

A Sustainable Solid Electrolyte Interphase for High‐Energy‐Density Lithium Metal Batteries Under Practical Conditions

High‐energy‐density Li metal batteries suffer from a short lifespan under practical conditions, such as limited lithium, high loading cathode, and lean electrolytes, owing to the absence of appropriate solid electrolyte interphase (SEI). Herein, a sustainable SEI was designed rationally by combining fluorinated co‐solvents with sustained‐release additives for practical challenges. The intrinsic uniformity of SEI and the constant supplements of building blocks of SEI jointly afford to sustainable SEI. Specific spatial distributions and abundant heterogeneous grain boundaries of LiF, LiN_xO_y, and Li₂O effectively regulate uniformity of Li deposition. In a Li metal battery with an ultrathin Li anode (33 μm), a high‐loading LiNi_0.5Co_0.2Mn_0.3O₂ cathode (4.4 mAh cm^?2), and lean electrolytes (6.1 g Ah^?1), 83 % of initial capacity retains after 150 cycles. A pouch cell (3.5 Ah) demonstrated a specific energy of 340 Wh kg^?1 for 60 cycles with lean electrolytes (2.3 g Ah^?1).     

Monolithic Phosphate Interphase for Highly Reversible and Stable Zn Metal Anode

Zinc metal battery (ZMB) is promising as the next generation of energy storage system, but challenges relating to dendrites and corrosion of the zinc anode are restricting its practical application. Here, to stabilize Zn anode, we report a controlled electrolytic method for a monolithic solid-electrolyte interphase (SEI) via a high dipole moment solvent dimethyl methylphosphonate (DMMP). The DMMP-based electrolytes can generate a homogeneous and robust phosphate SEI (Zn₃(PO₄)₂ and ZnP₂O₆). Benefiting from the protecting impact of this in situ monolithic SEI, the zinc electrode exhibits long-term cycling of 4700 h and a high Coulombic efficiency 99.89 % in Zn|Zn and Zn|Cu cell, respectively. The full V₂O₅|Zn battery with DMMP-H₂O hybrid electrolyte exhibits a high capacity retention of 82.2 % following 4000 cycles under 5 A g⁻¹. The first success in constructing the monolithic phosphate SEI will open a new avenue in electrolyte design for highly reversible and stable Zn metal anodes.     

Investigation of interfacial processes in graphite thin film anodes of lithium-ion batteries by both in situ and ex situ infrared spectroscopy

Graphite thin film anodes with a high IR reflectivity have been prepared by a spin coating method. Both ex situ and in situ microscope FTIR spectroscopy (MFTIRS) in a reflection configuration were employed to investigate interfacial processes of the graphite thin film anodes in lithium-ion batteries. A solid electrolyte interphase layer (SEI layer) was formed on the cycled graphite thin film anode. Ex situ MFTIRS revealed that the main components of the SEI layer on cycled graphite film anodes in 1 mol L -1 LiPF6 /ethylene carbonate + dimethyl carbonate (1:1) are alkyl lithium carbonates (ROCO2 Li). The desolvation process on graphite anodes during the initial intercalation of lithium ion with graphite was also observed and analyzed by in situ MFTIRS.     

Inorganic–Organic Hybrid Multifunctional Solid Electrolyte Interphase Layers for Dendrite-Free Sodium Metal Anodes

Constructing a stable and robust solid electrolyte interphase (SEI) is crucial for achieving dendrite-free sodium metal anodes and high-performance sodium batteries. However, maintaining the integrity of SEI during prolonged cycle life under high current densities poses a significant challenge. In this study, we propose an integrated multifunctional SEI layer with inorganic/organic hybrid construction (IOHL−Na) to enhance the durability of sodium metal anode during reduplicative plating/stripping processes. The inorganic components with high mechanical strength and strong sodiophilicity demonstrate optimized ionic conduction efficiency and dendrite inhibition ability. Simultaneously, the organic component contributes to the formation of a dense and elastic membrane structure, preventing fracture and delamination issues during volume fluctuations. The symmetrical batteries of IOHL−Na achieve stable cycling over 2000 hours with an extremely low voltage hysteresis of around 15.8 mV at a high current density of 4 mA cm⁻². Moreover, the Na−O₂ batteries sustain exceptional long-term stability and impressive capacity retention, exploiting a promising approach for constructing durable SEI and dendrite-free sodium metal anodes.     

Fluorinated Aromatic Diluent for High‐Performance Lithium Metal Batteries

In lithium metal batteries, electrolytes containing a high concentration of salts have demonstrated promising cyclability, but their practicality with respect to the cost of materials is yet to be proved. Here we report a fluorinated aromatic compound, namely 1,2‐difluorobenzene, for use as a diluent solvent in the electrolyte to realize the “high‐concentration effect”. The low energy level of the lowest unoccupied molecular orbital (LUMO), weak binding affinity for lithium ions, and high fluorine‐donating power of 1,2‐difluorobenzene jointly give rise to the high‐concentration effect at a bulk salt concentration near 2 m , while modifying the composition of the solid‐electrolyte‐interphase (SEI) layer to be rich in lithium fluoride (LiF). The employment of triple salts to prevent corrosion of the aluminum current collector further improves cycling performance. This study offers a design principle for achieving a local high‐concentration effect with reasonably low bulk concentrations of salts.     

Succinonitrile as a high-voltage additive in the electrolyte of LiNi0.5Co0.2Mn0.3O2/graphite full batteries

As a functional additive, succinonitrile (SN) can be used in LiNi_0.5Co_0.2Mn_0.3O₂/graphite lithium ion batteries to broaden the oxidation electrochemical window of the electrolyte and significantly improve its rate performance and high-voltage cycle performance. Linear sweep voltammetry (LSV) shows that EC/EMC-based electrolytes with SN have higher oxidation potentials (approximately 6.1 V vs Li/Li⁺). The capacity retention of LiNi_0.5Co_0.2Mn_0.3O₂/graphite full cell with 0.5-wt% SN added to the electrolyte and 120 cycles between 2.75 and 4.4 V was significantly increased from 67.96% to 84.0%. It is indicated that the LiNi_0.5Co_0.2Mn_0.3O₂ (NCM523) battery containing 0.5-wt% SN-based electrolyte has better cycleability and capacity retention at high cutoff voltage. In addition, electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) of the full cell were used to characterize the effect of SN on the cell. It is proved that the SN participates in the interfacial reaction between the electrode and the electrolyte to form a stable solid electrolyte interphase (SEI) layer, thereby effectively suppressing the increase of the charge transfer resistance and reducing the elution of the transition metal cations. These results indicate that SN can be used as a functional additive for high-voltage lithium-ion batteries.     

Hydrophobic Organic-Electrolyte-Protected Zinc Anodes for Aqueous Zinc Batteries

Aqueous Zn batteries are promising energy-storage devices. However, their lifespan is limited by irreversible Zn anodes owing to water decomposition and Zn dendrite growth. Here, we separate aqueous electrolyte from Zn anode by coating a thin MOF layer on anode and filling the pores of MOF with hydrophobic Zn(TFSI)₂-tris(2,2,2-trifluoroethyl)phosphate (TFEP) organic electrolyte that is immiscible with aqueous Zn(TFSI)₂–H₂O bulk electrolyte. The MOF encapsulated Zn(TFSI)₂-TFEP forms a ZnF₂-Zn₃(PO₄)₂ solid electrolyte interphase (SEI) preventing Zn dendrite and water decomposition. The Zn(TFSI)₂-TFEP@MOF electrolyte protected Zn anode enables a Zn||Ti cell to achieve a high average Coulombic efficiency of 99.1 % for 350 cycles. The highly reversible Zn anode brings a high energy density of 210 Wh kg⁻¹ (of cathode and anode mass) and a low capacity decay rate of 0.0047 % per cycle over 600 cycles in a Zn||MnO₂ full cell with a low capacity ratio of Zn:MnO₂ at 2:1.     

Lithium Bis(oxalate)borate Additive for Self-repairing Zincophilic Solid Electrolyte Interphases towards Ultrahigh-rate and Ultra-stable Zinc Anodes

The artificial solid electrolyte interphase (SEI) plays a pivotal role in Zn anode stabilization but its long-term effectiveness at high rates is still challenged. Herein, to achieve superior long-life and high-rate Zn anode, an exquisite electrolyte additive, lithium bis(oxalate)borate (LiBOB), is proposed to in situ derive a highly Zn²⁺-conductive SEI and to dynamically patrol its cycling-initiated defects. Profiting from the as-constructed real-time, automatic SEI repairing mechanism, the Zn anode can be cycled with distinct reversibility over 1800 h at an ultrahigh current density of 50 mA cm⁻², presenting a record-high cumulative capacity up to 45 Ah cm⁻². The superiority of the formulated electrolyte is further demonstrated in the Zn||MnO₂ and Zn||NaV₃O₈ full batteries, even when tested under harsh conditions (limited Zn supply (N/P≈3), 2500 cycles). This work brings inspiration for developing fast-charging Zn batteries toward grid-scale storage of renewable energy sources.