3,5—二羟基甲苯比色法测定棉纤维表面糖的方法研究

本文研究了在非离子表面活性剂存在下,糖在强酸介质中转化成糠醛类衍生物同3.5-二羟基甲苯发生显色反应的条件。在硫酸介质中,糠醛与3,5-二羟基甲苯形成化合物的最大吸收波长为λ_(max)=425nm,线性范围0.04～0.20mg/ml,用于测定棉纤维表面的糖,方法的相对标准偏差为1.3％,回收率92％～105％。     

5-甲基-7-甲氧基异黄酮的合成

5-甲基-7-甲氧基异黄酮的合成;二羟基甲基脱氧安息香; 甲基甲氧基异黄酮; 二羟基甲苯; 有机合成     

高效液相色谱法快速测定食品中抗氧化剂BHA,BHT

采用甲醇浸提食品样品中抗氧化剂ＢＨＡ（叔丁基羟基茴香醚）和ＢＨＴ（二叔丁基羟基甲苯），然后用高效液相色谱法测定提取液中的ＢＨＡ和ＢＨＴ。该法简单快速，准确性好，ＢＨＡ和ＢＨＴ的最小检出量分别为５ｎｇ和１０ｎｇ。     

HPLC／UV法对银鲫肌肉组织中甲苯咪唑及其代谢产物残留的同时测定

建立了一种用高效液相色谱同时测定银鲫肌肉组织中甲苯咪唑(MBZ)及其代谢物氨基甲苯咪唑和羟基甲苯咪唑的方法.银鲫肌肉组织用乙酸乙酯提取,萃取物旋转蒸发至干后用1 mL二甲基甲酰胺-0.05 mol/L磷酸盐缓冲液(体积比3 ∶ 7)定容.色谱条件:Waters symmetry C18反相色谱柱(250 mm×4.6 mm,5 μm);流动相:乙腈-0.05 mol/L磷酸二氢铵溶液(体积比33 ∶ 67);流速:0.8 mL/min;检测波长为298 nm;检测温度为室温.在10 ～120 μg/kg添加水平,MBZ、MBZ-NH2、MBZ-OH的回收率分别为81% ～86%、71% ～75%、86% ～93%.MBZ的检出限为2 μg/kg,MBZ-OH和MBZ-NH2检出限均为3 μg/kg.     

用气溶胶飞行时间质谱实时探测甲苯光氧化产生的单个二次有机气溶胶粒子

在烟雾腔内, 用紫外光照射甲苯、亚硝酸甲酯、一氧化氮和空气的混合物, 可以启动甲苯和羟基自由基(OH·)的光氧化反应和一系列的后续反应, 产生非挥发性和半挥发性有机化合物. 半挥发性有机化合物可以在气态和粒子态之间进行分配, 产生二次有机气溶胶粒子. 用自制的气溶胶飞行时间质谱仪, 快速、实时测量这些粒子的尺度、它们的分子成分和直径分布.     

3,5-二烷氧基甲苯的溴化反应研究

3,5-二甲氧基甲苯在偶氮二异丁腈的存在下与N-溴代丁二酰亚胺(NBS)反应,产物不是3,5-二甲氧基苄溴,而是2-溴-3,5-二甲氧基甲苯和2,6-二溴-3,5-二甲氧基甲苯.同样条件下,3,5-二乙酰氧基甲苯与NBS反应则生成3,5-二乙酰氧基苄溴.GAUSSIAN 03计算的结果表明,3,5-二甲氧基甲苯中苯环碳原子上的电荷密度高于侧链上碳原子上的电荷密度,因此溴自由基更容易取代苯环上的氢,而3,5-二乙酰氧基甲苯的情况恰好相反,故产物是3,5-二乙酰氧基苄溴.     

同位素稀释高效液相色谱-串联质谱法测定水产品中甲苯咪唑及其代谢物的残留量

建立了同时分析水产品中甲苯咪唑及其代谢物羟基甲苯咪唑和氮基甲苯咪唑的同位素稀释高效液相色谱串联质谱法.向样品中添加磷酸二氢钠溶液后用乙酸乙酯提取,提取液用氮气吹干后经2 mL甲醇-0.1%甲酸溶液(体积比1:1)溶解,正己烷去脂.以Hypersil GOLD为色谱分离柱,甲醇-0.1%甲酸溶液为流动相,流速为0.2 m...     

气相-质谱选择离子法测定化妆品中抗氧化剂丁基羟基茴香醚、二丁基羟基甲苯

 采用气相 质谱 (选择离子方式 )测定化妆品中抗氧化剂丁基羟基茴香醚 (BHA)和二丁基羟基甲苯(BHT) ,样品用甲醇振荡萃取 ,以SupelcoWAXTM 10 (30m× 0 2 5mmi.d .× 0 2 5 μm)为分析柱。该方法对样品中BHA和BHT的检测限分别为 2 5 μg/g和 0 5 μg/g。方法简便、快速、灵敏 ,可用于多种化妆品的检验。     

(S)-4-羟基吡咯烷-2-酮的简便合成

(S)-3-羟基-γ-丁内酯开环制得手性3,4-二羟基丁酸甲酯(2);对2的伯羟基进行对甲苯磺酰化、仲羟基进行苄基保护得4-对甲苯磺酰氧基-3-苄氧基丁酸甲酯(5);5在氨甲醇作用下合环、脱苄基保护合成了(S)-4-羟基吡咯烷-2-酮,总收率26%,其结构经1HNMR和HR-MS确认,比旋光值与文献值相符。     

顶空富集-气相色谱-质谱联用法测定聚醚中3，5-二新丁基-4-羟基-甲苯

采用气相色谱与质谱联用法测定了聚醚中3,5-二新丁基-4-羟基-甲苯(BHT),并采用顶空富集方法,与溶剂萃取富集法比较,此文中提出的顶空分离法具有不需用大量萃取溶剂,简化了操作步骤,加快了分析速度等优点,而所测得的结果与溶剂萃取法相一致.     

Theoretical Study of Intradimer Mechanism for Diamond Growth over Diamond (100)

The study of the energetics of the accepted intradimer diamond growth mechanism over (100) diamond surface is presented. The calculations were made in a density functional approach with the DGauss code using a DZVP2 basis set and a BLYP interchange and correlation potential. A simple 9-carbon cluster modeling the (100) diamond surface was used; its validity is discussed in relation with other calculations that used larger model clusters. The mechanism, presented in six steps, is based in the Harris and Garrison's work that considers the methyl radical as the main growth precursor agent and the breaking of the dimer surface bond with the corresponding methylene radical formation as a prior step to the formation of a CH₂-bridge structure, which is a feasible step; in contrast to these molecular dynamics results, Huang and Frenklach, using semiempirical methods, consider the breaking of the dimer surface bond and the formation of a CH₂-bridge structure as one step and this step as the energetically determinant of the mechanism. They also found an activation energy barrier for the interaction between a radical surface center with a H and CH₃. The present work tries to discern between these two ideas by calculating the activation barriers and the reaction energies for each step of the Harris and Garrison's mechanism in a density functional approach and comparing them to the results of Huang and Frenklach. The energy calculations point toward the scission of the dimer bond (step 4) as the determinant step; this step is endothermic, with an energy barrier of 50.43 kcal-mol^–1. On the other hand, the formation of the CH₂-bridge structure (step 5) is a feasible step with an energy barrier of 13.57 kcal-mol^–1. The adsorption of CH₃ (step 2) and H (step 6) species over radical surface sites did not involve any energy barriers, as it would be hoped. These steps were strongly exothermic and are close to the thermodynamic values for C—C and C—H bond energies. The removal of methylic hydrogen (step 3) did not show any problem because the activation barrier is only 3.68 kcal-mol^–1 less than the removal of a surface hydrogen (step 1), which has an energy barrier of 19.59 kcal-mol^–1. All steps, except number 4, were exothermic.     

Modeling hydrogen evolution from the Fe4S4 and Fe8S9X (X = N,C) clusters. Can a Fe?S high‐spin cluster serve as a surrogate for the FeMo cofactor?

A high-spin model of nitrogenase with a Fe(8)S(9)X(+) cluster (X = nitrogen or carbon) is used to test a mechanism for molecular hydrogen production, which is known to accompany ammonia production. The reaction proceeds with a series of protonation-reduction (PR) steps which are considered to be spontaneous if the calculated hydrogen-cluster bond energy exceeds 35-40 kcal/mol. The novel features of this mechanism include the opening of the cluster when one of the bridging sulfides undergoes two PR steps and the direct participation of the central atom when it undergoes a PR step. After the sixth PR step, a cluster is formed which has a low barrier for loss of molecular hydrogen in an exothermic reaction step. The central atom (nitrogen or carbon) has only a minor effect on the reaction steps.     

Synthesis of Highly Substituted Hexahelicenes

C₂‐Symmetric hexahelicenes 3a – 3g , which bear four or six alkoxy chains, were prepared in eight‐to‐nine reaction steps in high overall yields. The final step consisted of a twofold oxidative photocyclization of the corresponding 2,7‐bis(2‐phenylethenyl)naphthalenes. Long (and branched) chains provide a good solubility and processability, which is a prerequisite for applications in organic synthesis and materials science.     

Further mechanistic information on the reaction between FeIII(edta) and hydrogen peroxide: observation of a second reaction step and importance of pH

A detailed study of the effect of buffer, temperature, and pressure on the reaction of hydrogen peroxide with [Fe(III)(edta)H(2)O](-) was performed using stopped-flow techniques. The reaction was found to consist of two steps and resulted in the formation of the already characterized high-spin Fe(III) side-on bound peroxo complex. The second step of the reaction was found to be independent of the hydrogen peroxide concentration. Formation of the purple peroxo complex is only observable above pH 7.5. Both reaction steps are affected by specific and general acid-catalysis. Five different buffer systems were used to clarify the role of general acid-catalysis in these reactions. Both reaction steps reveal an element of reversibility, which disappears on decreasing the acid concentration. The positive volumes of activation for both the forward and reverse reactions of the first step suggest a dissociative interchange substitution process for the reversible end-on binding of hydrogen peroxide to [Fe(III)(edta)H(2)O](-). The small negative volume of activation for the second reaction step suggests an associative interchange mechanism for the formation of the side-on bound peroxo complex that is accompanied by dissociation of one of the four carboxylates of edta. A detailed mechanism in agreement with all the reported kinetic data is presented.     

Electroreduction of 6-amino-5-nitroso-1,3-dimethyluracil on polycrystalline platinum and nickel cathodes in acid aqueous solution

The reduction of 6-amino-5-nitroso-1,3-dimethyluracil (ANDMU) is a key step in caffeine synthesis. Electroreduction technology is a promising green chemical process. The voltammetric behavior of ANDMU at polycrystalline platinum and nickel cathodes was studied. The Nicholson theory was used to resolve the reduction process semi-quantitatively. The results show that ANDMU mainly undergoes an ECE (electron transfer, chemical reaction, electron transfer) process involving four electrons on the platinum and nickel cathodes in which the two electron-transfer steps occur at almost the same potential and the rate of the coupling chemical reaction between two electron-transfer steps is very fast. Apparent kinetic data and diffusion coefficient were determined for the platinum rotating-disk electrode.     

Study on the consecutive reaction kinetics of synthesis of di(2‐ethylhexyl) terephthalate under nonisothermal conditions

Since more information concerning kinetic parameters can be obtained from a nonisothermal reaction, it was selected to investigate the consecutive esterification kinetics of terephthalic acid with 2‐ethylhexanol in the presence of tetrabutyl titanate catalyst. This is an equilibrium reaction that is carried out in industry to completion by removing the water formed. It results in an automatic rise in the esterifying temperature, from 453 to 519 K. Research shows that the first step of esterification carried out in a heterogeneous system has a slow reaction rate, but the second step of esterification in a homogeneous system has a relatively fast reaction rate. Based on the quasi‐homogeneous assumption, first the differential method is presented to deal with nonisothermal reaction data. Arrhenius equations of the two steps are established by using this method. It was found that the apparent activation energy of the first step of esterification was about 55 kJ/mol higher than that of the second step. The ratio (K) of reaction rate constants of the two steps decreases gradually with the increase in the reaction temperature. An equation of K vs. temperature is also derived from Arrhenius equations. Subsequently, integral expressions of components' concentrations are used to simulate experimental results of the nonisothermal reaction as well as a three‐stage isothermal reaction. The obtained simulations show that the determined kinetic equations and the parameters are reasonable. © 2006 Wiley Periodicals, Inc. Int J Chem Kinet 38: 577–584, 2006     

Experimental and Theoretical Insight into the Kinetics and Mechanism of the Synthesis Reaction of 2,3‐Dihydro‐2‐phenylquinazolin‐4(1H)‐one Catalyzed in Formic Acid

An efficient and simple method has been developed for the synthesis of 2,3‐dihydro‐2‐phenylquinazolin‐4(1H )‐one catalyzed in formic acid. Also, the synthesis reaction between benzaldehyde and 2‐aminobenzamid was monitored spectrally. On the basis of the kinetic data obtained by the UV–vis spectrophotometry, both the first and second steps of the speculative five steps mechanism were enabled to be a rate‐determining step and also reaction showed second‐order kinetics. Considering information obtained by the stopped‐flow technique indicated that the first step is certainly a fast step. Moreover, the reaction was energetically and thermodynamically evaluated using theoretical methods and results were profoundly compared with the experimental approaches. Herein, theoretical rate constants were obtained using potential energy surfaces and the transition state theory at the B3LYP/6–311+G** level of theory. The Winger method was also applied to describe the tunneling effects. Calculations showed that the second step was the rate‐determining step in accordance with the experimental data. It is also found that the oxidation step was the fastest step in the proposed mechanism. For all five steps, two possibilities were considered for generating the probable product by using the thermodynamic parameters and kinetic data. Thermodynamic parameters also showed an exothermic reaction.     

Design, synthesis, and biological evaluation of a library of 1-(2-thiazolyl)-5-(trifluoromethyl)pyrazole-4-carboxamides

A library of 422 1-(2-thiazolyl)-5-(trifluoromethyl)pyrazole-4-carboxamides was prepared in five steps using solution-phase chemistry. The first step in the synthesis was the reaction of ethyl 2-ethoxymethylene-3-oxo-4,4,4-trifluorobutanoate with thiosemicarbazide, which is reported in the literature to afford a 1:1 mixture of ethyl 1-thiocarbamoyl-5-(trifluoromethyl)pyrazole-4-carboxylate and ethyl 1-thiocarbamoyl-3-(trifluoromethyl)pyrazole-4-carboxylate. We reassigned the structure of the product to be a single compound, ethyl 5-hydroxy-1-thiocarbamoyl-5-(trifluoromethyl)-4,5-dihydro-1H-pyrazole-4-carboxylate. This common intermediate was diversified by reaction with 17 alpha-bromoketones affording, in two steps, 17 1-(2-thiazolyl)-5-(trifluoromethyl)pyrazole-4-carboxylic acids. Scavenger resins were used to facilitate formation and purification of up to 27 amides from each of these acids in the last step. In addition, the Curtius reaction was applied to 12 of the acids followed by quenching with alcohols to afford a 108-member carbamate library. Certain compounds in the two libraries were toxic to C. elegans.     

Effect of Bio-based Catalyst in Biodiesel Synthesis

A cost-effective and environmentally friendly biodiesel synthesis has drawn attention in recent research activities. Used cooking oil which is known as waste is used in this study. The objectives of this research were to study an effect of biobased-catalyst which is used as supporting catalyst in simultaneous ozonolysis and transesterification for biodiesel synthesis and to study the effect of two steps process in biodiesel synthesis. The bio-based catalyst used in this process was empty palm bunch ash which was used as supporting catalyst for KOH. Two steps reaction were designed, the first step was run in a reactor at 30 °C with a continuous supply of ozone gas for 3 hours to cleave the unsaturated fatty acids at the double bonds. The second step was a follow up process after the first step without a supply of ozone gas, the temperature was increased up to 60 °C and the reaction continue for two hours. The second step aimed to convert saturated fatty acid which was not yet fully converted at the first step. Results of this study showed that 1.5% of KOH gave better performance in producing short chain methyl esters compared to 1% of KOH in the first step process at various percent weight of ash. The highest short chain methyl esters and long chain methyl esters produced in the first step process were 85.722 mg/liter and 655.286 mg/liter respectively, which was used 17.3 weight % ash and 1.5 weight % KOH. Short chain methyl esters were produced as a result of unsaturated fatty acid cracked by ozonolysis. It is confirmed that a simultaneous ozonolysis and transesterification occurred in the first step process. In conclusion, the presence of bio-based catalyst as supporting catalyst for KOH to produce higher total methyl esters has been effective. The second step process in this experiment was not effective since the effect of reaction time can enhance the hydrolysis of esters as a reverse reaction of transesterification, resulted in loss of esters.     

Synthesis of (‐)‐herbertenediol and (aR,aS)‐mastigophorenes A via asymmetric intramolecular heck coupling reaction

Total enantioselective synthesis of the natural (‐)‐Herbertenediol (1) was accomplished in eleven steps with an overall yield of 15% starting from the 2‐methoxy‐4‐methyl‐phenol. The total synthesis features asymmetric intramolecular Heck reaction and Wolff‐Kishner‐Huang reduction. (aR, aS)‐Mastigophorenes A was also synthesized through the oxidative coupling reaction.