银元素的循环实验

设计并完成了由5步构成的银元素的循环实验,从银粉出发,经过银在硝酸中溶解,银离子与氯离子反应生成氯化银沉淀,氯化银溶解于氨水,银氨络离子与乙炔反应生成乙炔银,水合肼将乙炔银还原为单质银等化学反应,完成了银的循环实验。     

Idiosyncratic Ag7Pt2O7: An Electron Imprecise yet Diamagnetic Small Band Gap Oxide

The seminal qualitative concepts of chemical bonding, as presented by Walter Kossel and Gilbert Newton Lewis back in 1916, have lasting general validity. These basic rules of chemical valence still serve as a touchstone for validating the plausibility of composition and constitution of a given chemical compound. We report on Ag₇Pt₂O₇, with a composition that violates the basic rules of chemical valence and an exotic crystal structure. The first coordination sphere of platinum is characteristic of tetravalent platinum. Thus, the electron count corresponds to Ag₇Pt₂O₇*e⁻, where excess electrons are associated with the silver substructure. Such conditions given, it is commonly assumed that the excess electrons are either itinerant or localized in Ag−Ag bonds. However, the material does not show metallic conductivity, nor does the structure feature Ag-Ag pairs. Instead, the excess electrons organize themselves in 2e−4c bonds within the silver substructure. This subvalent silver oxide reveals a new general facet pertinent to silver chemistry.     

Influence of Temperature and Time on the Stability of Silver in Silica Sol-Gel Glasses

The darkening of silica sol-gel glasses doped with 0.05 mol% silver was studied. Six sols were prepared from TEOS and silver nitrate. Different additives were used, to influence the chemical and physical states of silver: oxidizing or reducing agents (H₂O₂, As₂O₅), colloid stabilizer (sodium citrate) and network modifiers (Li₂O, CaO). Sols were gelified at 60°C and densified at 600°C. The samples without additives and those prepared with H₂O₂ at room temperature even if they were protected from light. With increased temperature, the darkening became samples were heated above, 400°C, reversible bleaching took place. This darkening-bleaching is of thermal nature (“thermochromic effect”) and seems to be determined by a reversible aggregation-disaggregation of tiny silver particles. The presence of sodium citrate, as an additive delayed the darkening effect and the presence of CaO delayed it even further. Lithium oxide inhibited it totally.     

In-Situ Formation of AgCl Nanocrystallites in Films Prepared by the Sol-Gel and Silver Nanoparticles in Silica Glass Films

We are reporting on a novel preparation of silver chloride in sol-gel silica films as a precursor for nanoparticles of silver. The precipitation of silver chloride particles in-situ was achieved by the reaction of silver nitrate with trichloroacetic acid. The reaction leads to a slow release of chloride leading to a controlled precipitation of AgCl. The existence of an isotropic crystalline AgCl phase in the glass films was demonstrated by X-rays Diffraction Analysis (XRD) and Scanning Electron Microscope and Energy Dispersive Analysis of X-rays (SEM-EDAX). The resulting films are of good optical quality and exhibit a strong coloration upon irradiation with sunlight or heating to 600°C, due to the reduction of AgCl to silver nanoparticles. The absorption spectra of the films before and after irradiation are shown.     

银/聚合物纳米复合材料

银/聚合物纳米复合材料是一种典型的聚合物基复合材料, 其结构和性能依赖于合成方法,因此开发材料的优异性能必须以深入研究纳米材料的先进合成技术为前提。本文综述了纳米银粒子及其与聚合物形成的纳米复合材料的最新合成进展, 重点介绍了基于液相化学还原方法合成纳米银粒子的新方法, 如溶胶-凝胶法、沉淀法、微乳液法和离子液体法, 以及纳米银粒子的分散技术和原位法合成银/聚合物纳米复合材料的新技术, 并介绍了纳米银复合材料的电绝缘性、表面增强拉曼散射性能、抗菌性及其在生物医学等领域中的应用。     

单分散性银纳米粒子的可控制备

以卤化银或氧化银作为前驱体,室温下以水为溶剂,在较高溶液浓度下,利用化学还原法制备了单分散性银纳米粒子,并通过改变前驱体的种类,实现了粒径可控制备。采取扫描电子显微镜（SEM）、紫外-可见光谱仪（UV-Vis）、X射线-粉末衍射仪（XRD）、X射线-光电子能谱仪（XPS）等对所制备的银纳米粒子的形貌及成分进行了表征。结果显示,所制备的银纳米粒子具有较高的单分散性,粒径在40~150 nm之间,具有面心立方多晶结构。该方法制备的银纳米粒子可用于喷墨打印RFID天线。     

A study of the silver form of a natural zeolitic material of the clinoptilolite type

The silver forms of a natural zeolitic material (from the East Slovakian deposit) on the clinoptilolite type has been prepared. The silver forms of the natural zeolitic material were investigated by X-ray powder diffractometry, IR spectroscopy, ESCA measurements, scanning electron microscopy and conductivity measurements. Depending on the preparation conditions, the content of silver ions in the zeolitic products was found to be in the range from 16 to 24%. In the sample with a silver loading of 18.6%, the silver uptake is due to an ion exchange process, mostly involving Na(I), Ca(II) and Mg(II) ions.     

银纳米微球和银纳米棒自组装膜的制备及SERS研究

采用硼氢化钠还原硝酸银,用振荡器在不同转速下振荡得到单分散的银纳米微球和银纳米棒,再将银纳米微球及银纳米棒自组装于被3-氨丙基-三甲氧基硅烷(APTMS)修饰的玻璃基片上,制得了具有表面增强拉曼(SERS)活性的基底,分别以罗丹明6G(R6G)和罗丹明B(RB)为探针分子对这两种基底进行SERS活性检测,结果发现这两种基底均为较理想的SERS衬底。     

Fabrication of a Simple and Cheap Screen-printed Silver/Silver Chloride (Ag/AgCl) Quasi-reference Electrode

In this work, a silver/silver chloride ink is fabricated using two steps. First the silver ink is prepare using silver, nail polish and acetone. Then the silver ink is painted in a paper substrate and a silver chloride layer is deposited using a bleach solution. The result is the silver/silver chloride conductive ink. The silver ink is cheap ($2.49/g), well-dispersive and very easy to fabricate. The materials were characterized by SEM and XRD. The Ag ink showed the formation of a continuous network throughout the silver ink film with fewer agglomeration. The effective chlorination process was also observed in the Ag/AgCl characterization. Since the Ag/AgCl substrate will be used as a quasi-reference electrode, it is important to investigate the electrical properties. The Ag ink showed an average ohmic resistance of 2.27 Ω. The addition of the AgCl layer decreases the conductivity, as expected. In summary, the Ag/Ag/Cl ink developed is simple, well-dispersed, cheap and with good conductivity. Therefore, it can be used as a conductive ink in the fabrication of quasi-reference electrodes.     

Electrochemical Nanoparticle Sizing Via Nano-Impacts: How Large a Nanoparticle Can be Measured?

The field of nanoparticle (NP) sizing encompasses a wide array of techniques, with electron microscopy and dynamic light scattering (DLS) having become the established methods for NP quantification; however, these techniques are not always applicable. A new and rapidly developing method that addresses the limitations of these techniques is the electrochemical detection of NPs in solution. The ‘nano-impacts’ technique is an excellent and qualitative in situ method for nanoparticle characterization. Two complementary studies on silver and silver bromide nanoparticles (NPs) were used to assess the large radius limit of the nano-impact method for NP sizing. Noting that by definition a NP cannot be larger than 100 nm in diameter, we have shown that the method quantitatively sizes at the largest limit, the lower limit having been previously reported as ∼6 nm.¹     

Influence of SO2 on the durability of Ag/Al2O3 catalyst in lean NOx reduction by ethyl alcohol

The influence of SO₂ (200 ppm) on the durability of a Ag/Al₂O₃ catalyst for the reduction of NOx with ethyl alcohol was examined. The results strongly suggest that H₂O in diesel engine exhaust is essential for the high durability of Ag/Al₂O₃ catalyst in the presence of SO₂.     

Sonochemical Synthesis of Ag/AgCl Nanocubes and Their Efficient Visible‐Light‐Driven Photocatalytic Performance

A novel one‐step sonochemical approach to synthesize a plasmonic photocatalyst of AgCl nanocubes (ca. 115 nm in edge length) with a small amount of Ag metal species is presented. The nanoscale Ag/AgCl hybrid photocatalysts with cubic morphology are readily formed under ambient ultrasonic conditions and neither external heat treatment nor reducing agents are required. The size of the Ag/AgCl photocatalysts could be controlled by changing the concentrations of Ag⁺ ions and polyvinylpyrrolidone molecules in precursor solutions. The compositions, microstructures, influencing factors, and possible growth mechanism of the Ag/AgCl hybrid nanocubes were systematically investigated. The Ag/AgCl photocatalysts show excellent photocatalytic performance for degradation of various dye molecules under visible light.     

硬脂酸镍对以异位合成AgBr乳剂为光敏元的PTG材料感光性能的影响

本文报道了硬脂酸镍(NiSt₂)对以异位合成AgBr乳剂为光敏元的光敏热显影(PTG)材料感光性能的影响.结果表明AgBr与AgTTA的摩尔比为0.25时,PTG材料感光度最大,并且硬脂酸镍可将感光度提高约1.1倍。本文通过对AgBr乳剂的光吸收和硬脂酸镍的DSC的研究,初步分析了硬脂酸镍对PTG材料感光性能的影响原因.     

两种不同银源的光敏热成像材料感光性能对比

本文考察了以苯并三氮唑银为银源与以硬脂酸银为银源的水基型PTG材料感光性能的差异,采用了原位法和异位法两种方法来制备不同的PTG材料,并采用了加热显影与湿法显影两种方法显影,结果显示以AgBTA为银源的PTG材料的感光度都比以AgSt为银源的PTG材料的感光度高.通过对乳液pH值和pAg值以及Dember光电压的测定,发现显影过程中以AgSt为银源的PTG材料显影程度要比以AgBTA为银源的PTG材料显影程度高,潜影形成过程中AgBTA体系的潜影形成效率比AgSt体系的潜影形成效率高,导致最终实验结果是以AgBTA为银源的PTG材料的感光度比以AgSt为银源的PTG材料的感光度高.     

纳米银形状控制合成与聚合物纳米银复合材料

纳米银(Ag NPs)由于其独特的物理、化学和生物学特性备受研究人员的关注.纳米银应用性能除了受到粒子尺寸、分布、纯度等因素影响,还与纳米银的形状密切相关.纳米银的形状对纳米银的抗菌性能、光学性能以及聚合物纳米银复合材料的综合性能都会产生重要影响.纳米银的形状控制合成可以进一步发挥聚合物纳米银复合材料的性能潜力.因此,不断发展纳米银新的合成方法,研究纳米银形状控制的机理就显得尤为重要.本文综述了纳米银合成方法和不同形状纳米银的最新研究进展,合成方法重点介绍了辐射法、激光烧蚀法、电化学法、光化学法和生物合成法,评述了这些方法的优缺点;同时从模板法、动力学、热力学以及氧化刻蚀4个方面介绍了纳米银形状控制的机理.介绍了聚合物纳米银复合材料的研究进展.     

传统化学增感对PVA为粘合剂的光敏热成像材料的光敏性的影响

以水性聚乙烯醇(PVA)为粘合剂,以异位法制备的颗粒尺寸为140nm的AgBr乳剂作光敏元,考察了传统化学增感方法对PTG材料的光敏性影响.实验结果表明,分别将经过硫增感、金增感、硫加金增感以及还原增感的AgBr乳剂加入到PTG体系中,均提高了PTG体系的光敏性,而灰雾却没有明显的增长.     

New silver tellurite glasses

The glass forming ranges in the TeO₂-AgO_0.5 and TeO₂-AgO_0.5-AgI systems have been assessed for two cooling rates; results based on heat capacity and electrical conductivity measurements as well as derived from infrared spectroscopy are presented. The ternary glasses are excellent conductors due to the presence of Ag⁺ ions mainly supplied by AgI. The decrease in C _P with increasing AgI-content suggests the presence of AgI microdomains which are finely distributed and do not contribute to the configurational heat capacity change. Fast motion of Ag⁺ ions (low activation energy) occurs in the glassy matrix which shows slow structural relaxation (high activation barrier).This research is performed within the frame of a P.I.R.M.A.T. action of the CNRS.     

在SiO2表面合成光滑纳米银壳的新方法——热裂解-熔流法

A new route for the preparation of silver nanoshells on silica spheres, leading to the establishment of a simple, efficient and easy-to-scale-up way for the synthesis of smooth silver nanoshells on silica monodispersed spheres, is reported through transforming the silver oxide shell to zero-valence silver by thermal cracking, applying surface strain theory to alter the shape of core-metal shell colloidal and form smooth metal nanoshell in hot inert flowing liquid. SEM images show that the silver nanoshells may be formed at 130 ℃ and deformed at 180 ℃ in hot inert flowing liquid. XRD indicates the formation of cubic structure pure silver with high crystallinity. Also, EDX and UV diffuse reflection spectrum analyses were conducted to characterize the as-prepared samples.     

混合银盐的光敏热成像材料感光性能研究

本文以原位法合成的AgBrI作为光敏剂,亲水型的聚乙烯醇为粘合剂,考察了以苯并三氮唑银和4-羟基-6甲基-1,3,3a,7-四氮茚银混合银盐为银源的光敏热成像材料的感光性能,实验结果表明:含AgTAI的混合银盐的PTG材料感光性能明显好于单纯AgBTA的PTG材料.通过光敏热成像材料乳液pH值pAg值测定及银盐DSC分析,认为混合银盐能够提高PTG材料感光性能的原因是其溶解度比AgBTA的溶解度大,能够提供充足的Ag⁺,增大显影密度,提高反差,且混合银盐颗粒尺寸小,其比表面积大,能够充分接触超细卤化银颗粒,从而促进热显影的进行.