以离子液体为流动相添加剂的高效液相色谱法测定钩藤药材中钩藤碱和异钩藤碱

采用以离子液体为流动相添加剂的高效液相色谱法测定钩藤药材中钩藤碱和异钩藤碱的含量。钩藤药材样品0.532g用60%(体积分数)甲醇溶液10mL在25℃下超声提取30min。过滤后的续滤液以C18色谱柱为分离柱,以16.7 mmol·L~(-1)磷酸二氢钾缓冲溶液(pH 3.0,20mmol·L~(-1) 1-己基-3-甲基咪唑四氟硼酸盐离子液体作为添加剂)为流动相,在检测波长245nm处进行测定。钩藤碱与异钩藤碱的质量浓度均在1.56~100mg·L~(-1)内与其对应的峰面积呈线性关系,检出限(3S/N)依次为0.914,0.194 mg·L~(-1)。方法用于钩藤药材样品的分析,回收率为98.0%~101%,测定值的相对标准偏差(n=6)为0.60%~1.8%。     

离子液体作添加剂对高效液相色谱分离植物激素的影响

探讨了以离子液体作为液相色谱流动相添加剂,对植物激素赤霉素GA3、生长素IAA和脱落酸ABA的分离的影响,以及离子液体的烷烃链长度,阴离子及离子液体的浓度对分离的影响。结果表明:咪唑阳离子和植物激素通过静电作用而保留;植物激素本身的pKa值影响其保留因子,pKa值增大,离子液体浓度对植物激素保留因子影响增大;另外随[BMIM]对应的阴离子电负性的减小,植物激素的保留因子明显地增大;同时植物激素的空间位阻也影响其分离。     

离子液体作高效液相色谱流动相添加剂测定水杨酸

建立了以离子液体作反相高效液相色谱流动相添加剂测定水杨酸的方法.实验以ZORBAX ODS反相色谱柱为分离柱,采用紫外检测方法,研究了检测波长、离子液体烷基链长度、离子液体溶液的浓度以及pH值等对分离和测定的影响.优化的色谱条件为:以体积比60:40的甲醇-3.0 mmol/L1-丁基-3-甲基咪唑四氟硼酸盐溶液(乙酸...     

以离子液体作流动相添加剂高效液相色谱法分离辣椒素类生物碱

建立了以离子液体1-丁基-3-甲基咪唑四氟硼酸盐(BmimBF4)为流动相添加剂分离辣椒素类生物碱的方法及分离模型,探讨了其作用机理。考察了添加剂离子液体的种类、浓度、烷基链长度、柱温等因素的影响。结果显示以离液序列较高的阴离子离子液体作为置换剂,可明显改善此类生物碱的分析效果。离子液体的链长、浓度与组分保留因子的变化符合溶质计量置换保留模型(SDM-R),r>0.99,即分离作用过程完全符合溶质计量置换模型。     

离子液体作高效液相色谱流动相添加剂分离测定芳香族羧酸

以离子液体作反相高效液相色谱流动相添加剂,建立了分离测定对氨基苯甲酸、邻苯二甲酸、对羟基苯甲酸、水杨酸、苯甲酸、邻甲苯甲酸6种芳香族羧酸的方法。以C18反相色谱柱为分离柱,采用紫外检测方法,以离子液体作高效液相色谱流动相添加剂,考察了检测波长、甲醇含量、离子液体溶液的pH值、离子液体烷基链长度以及离子液体溶液浓度等分离及测定条件。优化得到的色谱条件为:以甲醇和1.0mmol/L 1-丁基-3-甲基咪唑四氟硼酸盐水溶液(pH 3.0)(体积比40∶60)为流动相;检测波长240 nm;流速1.0 mL/min;柱温30℃。在优化条件下对6种芳香族羧酸进行梯度洗脱,约在16.5 min内分离完全;在5~120 mg/L范围内,线性系数均在0.999以上;检出限为0.026~0.082 mg/L。方法的平均加标回收率为98.3%~103.8%,相对标准偏差不高于0.63%。将该方法应用于药品复方紫荆皮水杨酸溶液和足君清酊剂中芳香族羧酸的测定,结果满意。     

离子液体对淀粉酶催化反应的影响

用分光光度法研究了二烷基咪唑氯类和二烷基咪唑磷酸酯类离子液体对淀粉酶催化反应的影响,通过吸光度的变化来测定淀粉水解的程度。 结果表明,这两类离子液体对淀粉酶催化反应均有明显的抑制作用,其中1-己基-3-甲基咪唑氯[HMIM]Cl的抑制作用最大。 而且,对于相同的阴离子,随着阳离子咪唑环烷基取代基链长的增加,抑制作用也增加。     

离子液体作高效液相色谱流动相添加剂分离测定芳香胺

建立了以离子液体作反相高效液相色谱流动相添加剂分离测定邻苯二胺、苯胺和对甲苯胺3种芳香胺的方法。实验以C18反相色谱柱为分离柱,采用紫外检测方法,考察了检测波长、甲醇含量、咪唑离子液体烷基链长度、离子液体溶液浓度等条件对分离和测定的影响,并与其它分离测定芳香胺的方法进行了比较。优化的色谱条件为:以甲醇/1-丁基-3-甲基咪唑四氟硼酸盐水溶液(3.0mmol/L,乙酸调节pH 3.5)=30/70(V/V)为流动相;检测波长254 nm;流速1.0mL/min;柱温30℃。在此条件下,3种芳香胺达到基线分离,在6.5 min之内分离完全;在1～40 mg/L范围内,线性回归方程的相关系数达到0.99以上;检出限为0.07～0.41 mg/L。将本方法应用于废水的测定,加标回收率在92.3%～96.7%之间,相对标准偏差小于3.5%。     

咪唑离子液体作为流动相添加剂的整体柱离子对色谱快速分析哌啶阳离子

以咪唑离子液体作为流动相添加剂,建立了哌啶离子液体阳离子的整体柱离子对色谱-间接紫外检测分析方法。系统研究了流动相、流速等因素对哌啶阳离子分离测定的影响情况。流动相中的咪唑离子液体不仅起到了背景紫外吸收剂的作用,还改善了阳离子的分离效果。用0.5mmol/L 1-乙基-3-甲基咪唑四氟硼酸盐-0.1mmol/L庚烷磺酸盐水溶液(pH=4.5)/甲醇(90/10,V/V)作为流动相,流速3.0mL/min,检测波长210nm,N-甲基-N-乙基、N-甲基-N-丙基和N-甲基-N-丁基哌啶阳离子在3.0min之内实现基线分离。3种哌啶阳离子的检出限分别为0.13、0.34和0.42mg/L。该方法测定实验室合成的哌啶离子液体样品的加标回收率范围为94%~98%。     

梯度淋洗离子对色谱法测定咪唑离子液体中的阳离子

采用梯度淋洗离子对色谱-紫外检测(IPC-UV)法分离测定5种咪唑离子液体中的阳离子。实验采用ZORBAX Eclipse XDB C18色谱柱,以离子对试剂与乙腈为流动相,首先考察了离子对试剂种类和浓度、乙腈浓度和色谱柱温度对咪唑阳离子保留的影响,然后确定了最适宜分离的色谱条件。在此条件下可同时基线分离5种咪唑阳离子。所测阳离子的检出限(S/N=3)为0.05～0.30 mg/L,峰面积的相对标准偏差(RSD, n=5)在0.1%以下。将此方法用于分析实验室合成的2种1-烷基-3-甲基咪唑离子液体中的阳离子,加标回收率在98.6%～102.1%之间。本方法准确、可靠,具有较好的实用性。     

钩藤生物碱中一对异构体的TLC-FT-SERS研究

傅立叶变换表面增强喇曼光谱（FT－SERS）可高灵敏度检测单一组分的分子结构住处,金、银等金属的米粒子具有表面增强活性^[1],薄层色谱（TLC）可将微量混合物有效分离但不具备指纹检测功能,若将TLC与FT－SERS技术联用,则可使天然药物等提取得到高灵敏度分离与特征光谱检测,这项研究在国内外仅有补步报道^[2~5],钩藤为常用中草药,其有效成分生物碱具有改善心脑血液循环和脑功能的作用及清除自由基抗衰老活性,本文应用TLC－FT－SERS技术对天然药物钩藤中的生物碱进行高灵敏度的分析和特征喇曼光检测,在硅胶色谱板的钩藤碱与异钩藤碱与钩藤碱班点原位分别滴淋灰银胶,直接测得FT－SERS光谱。     

室温离子液体对氨基苯磺酸的萃取性能

系统研究了[C₄mim][PF₆], [C₆mim][PF₆], [C₆mim][BF₄]和[C₈mim][BF₄]室温离子液体对间氨基苯磺酸、对氨基苯磺酸稀水溶液的萃取平衡. 实验结果表明: 萃取温度和相体积比的变化对分配比影响不大; 水相pH值对萃取平衡有较大的影响, 氨基苯磺酸在离子液体/水体系中的分配比在pH＝4.2时达到最大值; 水相中CaCl₂或Na₂SO₄的存在能较大幅度地提高氨基苯磺酸的分配比; 离子液体的阴离子的性质对分配比有显著的影响, 阴离子为[BF₄]^－的离子液体对氨基苯磺酸的萃取能力大于阴离子为[PF₆]^－的离子液体; 咪唑环上烷基链的长度也对萃取效果有一定的影响. 在所研究的离子液体中, [C₆mim][BF₄]和[C₈mim][BF₄]对氨基苯磺酸有较好的萃取性能, 且萃取相中的氨基苯磺酸可回收利用, 离子液体也可循环使用.     

High-performance liquid chromatography utilization of ionic liquids as mobile phase additives for separation and determination of the isomers of amino benzoic acids

For the isomers of amino benzoic acid, including o-, m-, p-amino benzoic acid, the beneficial effects of using the ionic liquid, 1-butyl-3-methylimidazolium tetrafluoroborate ([BMIm][BF₄]), as mobile phase additives on retention behavior and separation were investigated. Chromatographic separation of the o-, m-, p-amino benzoic acid was performed on a reversed-phase C18 column by ultraviolet detection at 245 nm. The effects of several chromatographic parameters, concentrations and pH values of [BMIm][BF₄] solutions, methanol concentration and length of alkyl chain on different ionic liquids, on the separation and determination of the isomers were evaluated. The optimized chromatographic conditions were established using an aqueous 0.5 μmol/L [BMIm][BF₄] solution (pH 3.0)/methanol (40:60, v/v) as mobile phase without need of gradient elution, with separation of three amino benzoic acids achieved within four min. The calibration curve showed good linearity over the tested range of 2 mg/L to 120 mg/L for the three isomers with a correlation coefficients of 0.9999. The recoveries of the three amino benzoic acids of spiked components were between 99.8% and 100%. The method has been successfully applied to the determination of p-amino benzoic acid in the pharmaceutical, Bromine Mitag Procaine Injection.     

The performance of 1‐ethyl‐3‐methylimidazolium tetrafluoroborate ionic liquid as mobile phase additive in HPLC‐based lipophilicity assessment

Ionic liquids have been widely used as green alternative mobile phase additives to shield the residuals silanols groups and modify the stationary/mobile phase HPLC systems. The present study aimed to evaluate the performance of the ionic liquid 1‐ethyl‐3‐methylimidazolium tetrafluoroborate ([EMIM][BF4]) in producing extrapolated logk_w indices suitable to substitute for octanol–water logP or logD values. The effect of [EMIM][BF4] was investigated for a set of basic and neutral drugs using two different columns, BDS and ABZ⁺. [EMIM][BF4] was added simply alone or in combination with n‐octanol and was compared with the conventional masking agent n‐decylamine. [EMIM][BF4] reduced the retention by suppressing silanophilic interactions, althoug to a lower extent than n‐decylamine. Addition of n‐octanol further decreased the retention by shielding silanol sites on BDS and/or interacting with polar groups through hydrogen bonding on ABZ⁺. Logk_w/logD_7.4 relationships proved moderate compared with those derived upon addition of n‐decylamine. They were considerably improved upon the introduction of protonated fraction F⁺ in the correlation, reflecting ion pair formation between the chaotropic anion [BF4]^‐ and the protonated basic compounds. In this aspect, the ionic liquid [EMIM][BF4], although efficient as a masking agent, cannot be recommended as mobile phase additive to reproduce octanol–water partitioning. Copyright © 2010 John Wiley & Sons, Ltd.     

Crystal engineering in ionic liquids. The crystal structures of [Mppyr]3[NdI6] and [Bmpyr]4[NdI6][Tf2N

Single crystals of [mppyr][NdI6] and [bmpyr][NdI6][Tf2N] are the first surprising examples of how the cation of an ionic liquid determines the compound formation from an ionic liquid. Depending upon the variation of the length of the alkyl chain of the quaternary pyrrolidinium cation (C3 and C4, respectively), incorporation of the anion of the ionic liquid, [Tf2N]-, can either be evoked or suppressed.     

Surface tension of binary mixtures of imidazolium and ammonium based ionic liquids with alcohols, or water: cation, anion effect

The surface tensions were measured at atmospheric pressure, with use of a ring tensiometer, of a series of alcoholic solutions of closely related ionic liquids: 1-methyl-3-methylimidazolium methylsulfate, [MMIM][CH3SO4] in alcohol (methanol, or ethanol, or 1-butanol at 298.15 K), 1-butyl-3-methylimidazolium methylsulfate, [BMIM][CH3SO4] in alcohol (methanol, or ethanol, or 1-butanol at 298.15 K), 1-butyl-3-methylimidazolium octylsulfate, [BMIM][OcSO4] in alcohol (methanol, or 1-butanol at 298.15 K) and of 1-hexyloxymethyl-3-methylimidazolium tetrafluoroborate, [C6H(13)OCH2MIM][BF4], 1,3-dihexyloxymethylimidazolium tetrafluoroborate, [(C6H13OCH2)2IM][BF4] in alcohol (methanol, or 1-butanol, or 1-hexanol at 308.15 and 318.5 K) and hexyl(2-hydroxyethyl)dimethylammonium bromide, C6Br in 1-octanol at 298.15 K. The set of ammonium ionic liquids of different cations and anions (C2Br, C2BF4, C2PF6, C2N(CN)2, C3Br, C4Br and C6Br) was chosen to show the influence of small amount of the ammonium ionic liquid on the surface tension of water at 298.15 K. The influence of the cation, or anion alkyl chain length on the properties under study (densities and surface tension) was tested.     

Poly(ionic liquid)s: a new material with enhanced and fast CO2 absorption

Novel sorbent and membrane materials for CO2 separation, poly(ionic liquid)s made from ionic liquid monomers, poly[p-vinylbenzyltrimethyl ammonium tetrafluoroborate](P[VBTMA][BF4]) and poly[2-(methacryloyloxy)ethyltrimethylamnonium tetrafluoroborate](P[MATMA][BF4]) have absorption capacities 7.6 and 6.0 times of those of room-temperature ionic liquids, e.g.[bmim][BF4], respectively, with reversible and fast sorption and desorption.     

Simultaneous determination of three alkaloids in Huangbo using an ionic liquid as a mobile phase additive in reversed‐phase liquid chromatography

A reversed‐phase high‐performance liquid chromatography method for the simultaneous determination of jatrorrhizine, palmatine, and berberine in Huangbo, the dried bark of Chinese Corktree, was established by using 1‐hexyl‐3‐methylimidazolium tertafluoroborate as a mobile phase additive. The chromatographic behavior of the three compounds on the C₁₈ column was studied with four different types of 1‐alkyl‐3‐methylimidazolium‐based ionic liquids as the mobile phase additives. The effect of 1‐hexyl‐3‐methylimidazolium tertafluoroborate was the best in the four investigated ionic liquids. The concentration of 1‐hexyl‐3‐methylimidazolium tertafluoroborate and the pH of the mobile phase, which influenced the chromatographic behaviors of the three bioactive compounds, were investigated. The linearity, precision, accuracy, repeatability, limit of detection, and quantification of the proposed method were found to be satisfactory. To explain the role of ionic liquids as the mobile phase additives, the possible mechanism was also explored and discussed.