Surface defect states of CdTexS1 − x quantum dots

Properties of surface defect states of CdTe_xS_1 − x quantum dots with an average diameter of 7 nm are investigated experimentally. The stoichiometric ratio is found to be for by use of the energy dispersive analysis of x-ray. The photoluminescence spectrum, the photoluminescence excitation spectrum, and the surface passivation are adopted to characterize the properties of surface defect states. The energy levels of surface defect states of CdTe_xS_1 − x quantum dots are also determined.     

Photoluminescence investigation of ferromagnetic Ga1−xMnxN layers with GaN templates grown on sapphire (0 0 0 1) substrates

We have investigated the temperature and composition dependent photoluminescence (PL) spectra in Ga_1−xMn_xN layers (where x ≈ 0.1-0.8%) grown on sapphire (0 0 0 1) substrates using the plasma-enhanced molecular beam epitaxy technique. The efficient PL is peaked in the red (1.86 eV), yellow (2.34 eV), and blue (3.29 eV) spectral range. The band-gap energy of the Ga_1−xMn_xN layers decreased with increasing temperature and manganese composition. The band-gap energy of the Ga_1−xMn_xN layers was modeled by the Varshni equation and the parameters were determined to be α = 2.3 × 10⁻⁴, 2.7 × 10⁻⁴, 3.4 × 10⁻⁴ eV/K and β = 210, 210, and 230 K for the manganese composition x = 0.1%, 0.2%, and 0.8%, respectively. As the Mn concentration in the Ga_1−xMn_xN layers increased, the temperature dependence of the band-gap energy was clearly reduced.     

Influence of Co doping content on its valence state in Zn1−xCoxO (0 ≤ x ≤ 0.15) thin films

Zn_1−xCo_xO (0 ≤ x ≤ 0.15) thin films grown on Si (1 0 0) substrates were prepared by a sol-gel technique. The effects of Co doped on the structural, optical properties and surface chemical valence states of the Zn_1−xCo_xO (0 ≤ x ≤ 0.15) films were investigated by X-ray diffraction (XRD), ultraviolet-visible spectrometer and X-ray photoelectron spectroscopy (XPS). XRD results show that the Zn_1−xCo_xO films retained a hexagonal crystal structure of ZnO with better c-axis preferred orientation compared to the undoped ZnO films. The optical absorption spectra suggest that the optical band-gap of the Zn_1−xCo_xO thin films varied from 3.26 to 2.79 eV with increasing Co content from x = 0 to x = 0.15. XPS studies show the possible oxidation states of Co in Zn_1−xCo_xO (0 ≤ x ≤ 0.05), Zn_0.90Co_0.10O and Zn_0.85Co_0.15O are CoO, Co₃O₄ and Co₂O₃, with an increase of Co content, respectively.     

Structural studies of evaporated CoxCr1−x/Si (1 0 0) and CoxCr1−x/glass thin films

Series of Co_xCr_1−x thin films have been evaporated under vacuum onto Si (1 0 0) and glass substrates. Chemical composition and interface properties have been studied by modelling Rutherford backscattering spectra (RBS) using SIMNRA programme. Thickness ranges from 17 to 220 nm, and x from 0.80 to 0.88. Simulation of the energy spectra shows an interdiffusion profile in the thickest films, but no diffusion is seen in thinner ones. Microscopic characterizations of the films are done with X-ray diffraction (XRD) measurements. All the samples are polycrystalline, with an hcp structure and show a 〈0 0 0 1〉 preferred orientation. Atomic force microscopies (AFM) reveal very smooth film surfaces.     

High-temperature electrical properties of magnesiowustite Mg1 − xFexO and spinel Fe3 − x − yMgxCryO4 ceramics

Phase relationships, thermal expansion and electrical properties of Mg_1 − xFe_xO (x = 0.1-0.45) cubic solid solutions and Fe_{3 − x − y}Mg_xCr_yO_4 ± δ (x = 0.7-0.95; y = 0 or 0.5) spinels were studied at 300-1770 K in the oxygen partial pressure range from 10 Pa to 21 kPa. Increasing iron content enlarges the spinel phase stability domain at reduced oxygen pressures and elevated temperatures. The total conductivity of the spinel ceramics is predominantly n-type electronic and is essentially p(O₂)-independent within the stability domain. The computer simulations using molecular dynamics technique confirmed that overall level of ion diffusion remains low even at high temperatures close to the melting point. Temperature dependencies of the total conductivity in air exhibit a complex behavior associated with changing the dominant defect-chemistry mechanism from prevailing formation of the interstitial cations above 1370-1470 K to the generation of cation vacancies at lower temperatures, and with kinetically frozen cation redistribution in spinel lattice below 700-800 K. The average thermal expansion coefficients of the spinel ceramics calculated from dilatometric data in air vary in the range (9.6-10.0) × 10^− 6 K^− 1 at 300-500 K and (13.2-16.1) × 10^− 6 K^− 1 at 1050-1370 K. Mg_1 − xFe_xO solid solutions undergo partial decomposition on heating under oxidizing and mildly reducing conditions, resulting in the segregation of spinel phase and conductivity decrease.     

Effect of Cr on the magnetic properties of evaporated CoxCr1−x/Si(1 0 0) and CoxCr1−x/glass thin films

Series of Co_xCr_1−x thin films have been evaporated under vacuum onto Si(1 0 0) and glass substrates. Thickness ranges from 17 to 220 nm, and x from 0.80 to 0.88. Alternating gradient field magnetometer (AGFM) measurements provided saturation magnetization values ranging from 220 to 1200 emu/cm³. Values of squareness exceeding 0.8 have been measured. Coercive field may reach values up to 700 Oe, depending on the percentage of chromium, as well as the substrate nature and the direction of the applied magnetic field. The saturation magnetization value decreases as the Cr content increases. In order to study their dynamical magnetic properties, Brillouin Light Scattering (BLS) measurements have been performed on these samples. Stiffness constant value and anisotropy magnetic field were adjusted to fit the experimental BLS spectra. These results are analyzed and correlated.     

AlN, GaN, AlxGa1 − xN nanotubes and GaN/AlxGa1 − xN nanotube heterojunctions

Semiconductor optoelectronic devices based on GaN and on InGaN or AlGaN alloys and superlattices can operate in a wide range of wavelengths, from far infrared to near ultraviolet region. The efficiency of these devices could be enhanced by shrinking the size and increasing the density of the semiconductor components. Nanostructured materials are natural candidates to fulfill these requirements. Here we use the density functional theory to study the electronic and structural properties of (10,0) GaN, AlN, Al_xGa_1 − xN nanotubes and GaN/Al_xGa_1 − xN heterojunctions, 0<x<1. The Al_xGa_1 − xN nanotubes exhibit direct band gaps for the whole range of Al compositions, with band gaps varying from 3.45 to 4.85 eV, and a negative band gap bowing coefficient of −0.14 eV. The GaN/Al_xGa_1 − xN nanotube heterojunctions show a type-I band alignment, with the valence band offsets showing a non-linear dependence with the Al content in the nanotube alloy. The results show the possibility of engineering the band gaps and band offsets of these III-nitrides nanotubes by alloying on the cation sites.     

First-principles study on the electronic and optical properties of SnxGe1 − x

The electronic and optical properties of the direct band gap alloys Sn_xGe_1 − x (x = 0.000, 0.042, 0.083, 0.125, 0.167, and 0.208) have been studied by using the generalized gradient approximation in the framework of the density functional theory. The calculated lattice constants obey Vergard's law. The band structures show that the alloys have direct band gap and the band gaps can be tunable by Sn contents. The optical properties of the Sn_xGe_1 − x alloys with the physical quantities such as the complex dielectric function, the energy-loss function and the static dielectric constant, respectively, are shown to support the potential application of infrared devices in the future.     

Desorption of surfactant and sintering of surface-modified PdxNi1 − x nanoparticles

A series of Pd_xNi_1 − x nanoparticles in a diameter of 6-7 nm were prepared by wet chemical reduction. They were then modified with two surfactants, stearic acid (SA) and polyethylene glycol (PEG). Desorption of the surfactant was studied using a temperature programmed desorption technique, and the sintering behavior of surface-modified Pd_xNi_1 − x nanoparticles was examined. Since surface energy of the nanoparticles depends on the alloy composition, it can be correlated with the desorption temperature of surfactant from the nanoparticle surface. Because Ni has a higher surface energy, the surfactant desorption temperature increases as the Ni content increases. With the same stoichiometry, the desorption temperature of SA is always higher than that of PEG. The SA-modified nanoparticles have higher thermal stability and are less sintered than PEG-modified nanoparticles. The sintering and growth behavior of the nanoparticles can be correlated with variation of surface energy due to different surface modification.     

Effects of UV photon irradiation on SiOx (0 < x < 2) structural properties

Thin films of a-SiO_x (0 < x < 2) were prepared by reactive r.f. magnetron sputtering from a polycrystalline-silicon target in an Ar/O₂ gas mixture. The oxygen partial pressure in the deposition chamber was varied so as to obtain films with different values of x. The plasma was monitored, during depositions, by optical emission spectroscopy (OES) system. Energy dispersive X-ray (EDX) measurements and infra-red (IR) spectroscopy were used to study the compositional and structural properties of the deposited layers.Structural modifications of SiO_x thin films have been induced by UV photons’ bombardment (wavelength of 248 nm) using a pulsed laser. IR spectroscopy and X-ray photoemission spectroscopy (XPS) were used to investigate the structural changes as a function of x value and incident energy. SiO_x phase separation by spinodal decomposition was revealed. The IR peak position shifted towards high wavenumber values when the laser energy is increased. Values corresponding to the SiO₂ material (only Si⁴⁺) have been found for laser irradiated samples, independently on the original x value. The phase separation process has a threshold energy that is in agreement with theoretical values calculated for the dissociation energy of the investigated material.For high values of the laser energy, crystalline silicon embedded in oxygen-rich silicon oxide was revealed by Raman spectroscopy.     

Structural,electronic and optical properties of CdxZn1 − xS alloys from first-principles calculations

Structural, electronic and optical properties as well as structural phase transitions of ternary alloy Cd_xZn_1 − xS have been investigated using the first-principles calculations based on the density functional theory. We found that the crystal structure of Cd_xZn_1 − xS alloys transforms from wurtzite to zinc blende as Cd content of x=0.83$x=0.83$. Effect of Cd content on electronic structures of Cd_xZn_1 − xS alloys has been studied. The bandgaps of Cd_xZn_1 − xS alloys with wurtzite and zinc blende structures decrease with the increase of Cd content. Furthermore, dielectric constant and absorption coefficient also have been discussed in detail.     

On the short-range order of the SiOx (0 ≤ x ≤ 2) surface

Fine (oscillating) structure (FS) in the elastically scattered electron spectra (ESES) [O. Bondarchuk, S. Goysa, I. Koval, P. Melnik, M. Nakhodkin, Surf. Sci. 258 (1991) 239; O. Bondarchuk, S. Goysa, I. Koval, P. Melnik, M. Nakhodkin, Surf. Rev. Lett. 4 (1997) 965] was used to investigate surface structure of the SiO_x (0 ≤ x ≤ 2). SiO_x surface with different stoichiometry was prepared by implantation of 500 eV oxygen ions into a silicon wafer. Fourier transformation of the FS ESES contains one peak at 2.32 Å for Si, two peaks at 1.62 Å and 2.65 Å for a-SiO₂ and three peaks centered at 1.6-1.7 Å, 2.1-2.2 Å and 2.65-3.04 Å for SiO_x. Peaks at 1.62 Å and 2.65 Å are assigned to Si-O and O-O nearest distances correspondently. Ratio of the area under the peak at 2.65 Å to the area under the peak at 1.62 Å turned out to be not constant but grows linearly with the composition parameter x. The latter is considered to prove validity of the Random Bond Model to describe short-range order on the surface of non-stoichiometric silicon oxide.     

Structural, magnetic and electronic transport properties of MnxGe1−x/Ge(0 0 1) films grown by MBE at 350 °C

We report on the structural, magnetic and electronic transport properties of thin Mn_xGe_1−x films grown at 350 °C. Isolated Mn₅Ge₃ nanoclusters, about 100 nm in size, were formed at the top surface of the film, dominating the magnetic properties of the whole film. Electronic transport properties show Mn doping effect indicating the presence of substitutional Mn ions dispersed in the Ge host, contributing to the formation of a Mn_xGe_1−x diluted phase. Electrical behaviour indicates a saturation effect with the raise of the nominal Mn concentration in the film, above x ≅ 0.03.     

Half-metallic antiferromagnetism in the ordered Cr1 − xCaxSb alloy from first-principles calculations

Compared to half-metallic ferromagnets, half-metallic antiferromagnets (precisely called half-metallic fully compensated ferrimagnets) are more promising candidates for spintronic applications since their zero magnetization leads to lower stray fields and thus tiny energy losses. Using the first-principles calculations, we have systematically investigated the electronic and magnetic properties of the ordered Cr_1 − xCa_xSb alloy. It is found that Cr_1 − xCa_xSb with x=0.125, 0.25, 0.5 and 0.75 all are half-metals like zinc-blende CrSb and CaSb. Interestingly, Cr_0.25Ca_0.75Sb is a half-metallic antiferromagnet with complete spin polarization, and the half-metallic antiferromagnetism is robust against the lattice compression and expansion and the choice of electronic exchange and correlation functional.     

Phase and electrical behaviour in the Bi14W1 − xLaxO24 − 3x/2 system

The compositional and thermal dependencies of phase and electrical behaviour of compositions in the system Bi₁₄W_1 − xLa_xO_{24 − 3x/2} (0.00 < x < 1.00) have been studied by X-ray powder diffraction, differential thermal analysis and a.c. impedance spectroscopy. The system exhibits polymorphism and phase separation, which shows both compositional and thermal dependence. Compositions with x = 0.25 and x = 0.50 exhibit a single phase tetragonal structure at room temperature. In contrast, the x = 0.75 composition at room temperature shows a mixture of a cubic phase and a secondary β-Bi₂O₃ related tetragonal phase. A full solid solution is observed at high temperatures, corresponding to the occurrence of a δ-Bi₂O₃ type phase. The appearance of the various phases correlates well with the observed electrical behaviour. The x = 0.75 composition exhibits exceptionally high conductivity at high temperatures (σ₈₀₀ = 1.34 S cm^− 1), but also shows significant phase separation at lower temperatures.     

Effect of a LaSrCoO3 buffer layer on Pb1 − xLaxTi1 − x/4O3 films studied by polarized Raman spectroscopy

A confocal Raman investigation of Pb_1 − xLa_xTi_1 − x/4O₃ (PLT) thin films grown by RF magnetron sputtering on PbO_x/Pt/Ti/SiO₂/Si substrates with an intermediate LaSrCoO₃ (LSCO) layer was performed. The influence of the LaSrCoO₃ buffer layer was analyzed taking advantage of the observed Raman spectral band variation, which varied according to different manufacturing procedures. In the presence of a LSCO layer, the A1(1TO) Raman mode, which was indicative of tetragonal distortion, was pronouncedly enhanced, and a slight deviation from the (0 0 1) plane of the film was observed from the angular dependence of the polarized Raman spectral intensity. Furthermore, the spectral band variation as well as the residual stress along the in-depth direction was measured in the film from cross-sectional spectral line scans. This latter measurement showed a relaxation of the lattice mismatch in the presence of LSCO and PbO layers.     

Electrical characteristics of hole resonant tunneling diodes with high Ge fraction (x > 0.4) Si/strained Si1−xGex/Si(1 0 0) heterostructure

Effectiveness of a Ge fraction modulated spacer in hole resonant tunneling diodes (RTDs) with Si/strained Si_1−xGe_x heterostructures epitaxially grown on Si(1 0 0) was investigated to improve the electrical characteristics at higher temperatures. Electrical characteristics measured for 30 RTDs, with the modulated spacer at higher Ge fraction (x = 0.48) on a single wafer, show that the deviation of the peak current and voltage at the resonant peak falls in ranges of ±25% and ±10%, respectively. For the RTDs, negative differential conductance (NDC) characteristics are obtained even at higher temperatures around 230 K than that for the RTDs with x = 0.42. The result indicates that the introduction of higher Ge fraction is effective for NDC in RTD at higher temperature.     

Scanning tunneling microscopy observation of initial growth of Sn and Ge1−xSnx layers on Ge(0 0 1) substrates

We have investigated the initial growth of Sn and Ge_1−xSn_x layers on Ge(0 0 1) surface by using scanning tunneling microscopy. After the growth of a 0.035 ML-thick Sn layer at room temperature, Sn clusters lining vertically to a dimer row was observed. In the case of the 0.035-0.018 ML-thick Sn growth at 250 °C, the characteristic surface reconstruction with the step-edge undulation like a comb was observed. In the growth of a Ge_0.994Sn_0.006 layer at 250 °C, the multilayer polynuclear growth with a lot of two-dimensional small domain was observed. These surface reconstructions should be accounted for by the large compressive stress induced in the surface layer due to the incorporation of Sn atoms.     

Mössbauer spectroscopy and magnetic properties in thin films of FexNi100−x electroplated on silicon (1 0 0)

Fe_xNi_100−x thin films were produced by galvanostatic electrodeposition on Si (1 0 0), nominal thickness 2800 nm, and x ranging 7-20. The crystalline structure of the sample was determined by X-ray diffraction (XRD). The magnetic properties were investigated by vibration sample magnetometry (VSM) and room temperature ⁵⁷Fe Mössbauer spectroscopy. Conversion Electron Mössbauer spectroscopy (CEMS) in both film surfaces for the thick self-supported films showed that the magnetic moment direction is in the plane and conventional transmission (MS) that the directions are out of the plane films. The results were interpreted assuming a three-layer model where the external layer has in-plane magnetization and the internal one, out of plane magnetization.