The Effect of Nb Loading on Catalytic Properties of Ni/Ce0.75Zr0.25O2 Catalyst for Methane Partial Oxidation

In this study,the effect of Nb loading on the catalytic activity of Ce_(0.75)Zr_(0.25)O_2-supported Ni catalysts was studied for methane partial oxidation.The catalysts were characterized by BET,H_2 chemisorption,XRD,TPR,TEM and tested for methane partial oxidation to syngas in the temperature range of 400-800℃at atmospheric pressure.The results showed that the activity of methane partial oxidation on the catalysts was apparently dependent on Nb loading.It seemed that the addition of Nb lowered the catalytic activity for methane partial oxidation and increased the extent of carbon deposition. This might be due to the strong interaction between NiO and Nb-modified support and reduction of surface oxygen reducibility.     

Effect of Ni Loading and Reaction Conditions on Partial Oxidation of Methane to Syngas

The partial oxidation of methane to synthesis gas is studied in this paper over Ni/Al2O3 catalysts under atmospheric pressure. The effects of Ni loading on the activity and stability of catalysts with 5 mm α-Al2O3 and θ-Al2O3 pellets as supports were measured in a continuous fixed bed reactor. It is found that the optimum Ni loading is 10%. And the effect of reaction conditions on partial oxidation of methane is also studied. The methane conversion and CO selectivity increase with the increase of the reaction temperature and the space velocity on 10%Ni/α-Al2O3 catalysts. The best CH4/O2 mole ratio is 2 for CO selectivity, and the optimum space velocity is 5.4x105 h-1.     

MgO纳米晶负载镍催化剂用于甲烷蒸汽重整反应(英文)

Nanocrystalline MgO with a relatively high surface area and mesoporous structure was synthesized by a surfactant assisted precipitation method for use as the support of nickel catalysts for steam reforming of methane. The samples were characterized by X‐ray diffraction, N2 adsorption, temperature‐programmed reduction, temperature‐programmed oxidation, scanning electron microscopy, and transmission electron microscopy. The catalysts showed high catalytic activity and good stability in the steam reforming of methane. Increasing the nickel loading up to 10 wt% gave increased activity. Catalysts with higher nickel loadings showed more deposited carbon after reaction. The excellent anti‐coking performance of the catalysts was attributed to the formation of a nickel‐magnesia solid solution, basicity of the support surface, and nickel‐support interaction.     

Partial Oxidation of Methane to Syngas Using LatticeOxygen of La_(1-x)Sr_xFeO_3 Perovskite OxideCatalysts Instead of Molecular Oxygen

Catalytic partial oxidation of methane to syngas using the lattice oxygen of La1-xSrxFeO3 perovskite oxide catalysts in place of molecular oxygen was studied. La1-xSrxFeO3 (x=0, 0.1, 0.2, 0.5) perovskite oxides were prepared by the "auto-combustion method". XRD analysis showed that all La1-xSrxFeO3 samples have a single-phase perovskite-type oxide. The redox properties of the catalysts were investigated by temperature programmed reduction with hydrogen (H2-TPR). Reducibility of the catalysts increase with the increasing of the Sr2+ content. The oxygen species of the catalysts and their reaction with CH4 were studied by the temperature programmed surface reaction (CH4-TPSR). In the absence of gas phase oxygen, there exist two kinds of oxygen species on the catalysts. One kind of the oxygen species with strong oxidative ability is produced first, which can oxidize CH4 completely to CO2 and H2O. Then, the second oxygen species with weak oxidative ability is formed, which can oxidize CH4 partially to CO and     

Syngas production by combined carbon dioxide reforming and partial oxidation of methane over Ni/α-Al_2O_3 catalysts

Ni/α-Al2O3 catalysts were found to be active in the temperature range 600 ～ 900℃ for both CO2 reforming and partial oxidation of methane.The effects of Ni loading,reaction temperature and feed gas ratio for the combination of CO2 reforming and partial oxidation of CH4 over Ni/α-Al2O3 were investigated.Catalysts of xwt%Ni/α-Al2O3(x=2.5,5,8 and 12) were prepared by wet impregnating the calcined support with a solution of nickel nitrate.XRD patterns and activity tests have verified that the 5wt%Ni/α-Al2O3 was the most active catalyst,as compared with the other prepared catalyst samples.An increase of the Ni loading to more than 5wt% led to a reduction in the Ni dispersion.In addition,by combining the endothermic carbon dioxide reforming reaction with the exothermic partial oxidation reaction,the loss of catalyst activity with time on stream was reduced with the amount of oxygen added to the feed.     

Complete Oxidation of Methane over Palladium Supported on Alumina Modified with Calcium,Lanthanum,and Cerium Ions

The activity and thermal stability of Pd/Al_2O_3 and Pd/(Al_2O_3 MO_x)(M=Ca,La,Ce) palladium catalysts in the reaction of complete oxidation of methane are presented in this study.The catalyst supports were prepared by sol-gel method and they were dried either conventionally or with supercritical carbon dioxide.Then they were impregnated with palladium nitrate solution.The catalysts with unmodified alumina had a high surface area.The activity and thermal stability of the alumina- supported catalyst was also very high.The introduction of calcium,lanthanum,or cerium oxide into alumina support caused a decrease of the surface area in the way dependent on the support precursor drying method.These modifiers decreased the activity of palladium catalysts,and they required higher temperatures for the complete oxidation of methane than unmodified Pd/Al_2O_3.The improvement of the palladium activity by lanthanum and cerium support modifier was observed only at low temperatures of the reaction.     

Syngas production by combined carbon dioxide reforming and partial oxidation of methane over Ni/α-Al2O3 catalysts

Ni/α-Al2O3 catalysts were found to be active in the temperature range 600~900 ℃ for both CO2 reforming and partial oxidation of methane. The effects of Ni loading, reaction temperature and feed gas ratio for the combination of CO2 reforming and partial oxidation of CH4 over Ni/α-Al2O3 were investigated. Catalysts of xwt%Ni/α-Al2O3 (x = 2.5, 5, 8 and 12) were prepared by wet impregnating the calcined support with a solution of nickel nitrate. XRD patterns and activity tests have verified that the 5wt%Ni/α-Al2O3 was the most active catalyst, as compared with the other prepared catalyst samples. An increase of the Ni loading to more than 5 wt% led to a reduction in the Ni dispersion. In addition, by combining the endothermic carbon dioxide reforming reaction with the exothermic partial oxidation reaction, the loss of catalyst activity with time on stream was reduced with the amount of oxygen added to the feed.     

Pretreatment of Alumina and Its Influence on the Properties of Co/Alumina Catalysts for Fischer-Tropsch Synthesis

16.6%Co/γ-Al_2O_3 catalysts prepared by incipient wetness impregnation method were used for Fischer-Tropsch synthesis.The support was pre-treated with different concentration of NH_4NO_3 aqueous solution.The effect of support pre-treatment on the properties of support and performance of supported- cobalt-based catalysts was investigated.To treat the support with NH_4NO_3 aqueous solution enlarged the pore ofγ-Al_2O_3,decreased the impurity Na_2O content,and weakened the surface acidity ofγ-Al_2O_3. The change in the properties of the support decreased the interaction between cobalt species and support, enhanced the CO hydrogenation rate and the C_(5 )selectivity.For all catalysts,increasing the reaction temperature increased the CO hydrogenation rate or the CO conversion,slightly decreased the total hydrocarbon selectivity,and favored the formation of methane and light hydrocarbons,while the chain growth probability decreased.For 16.6%Co/γ-Al_2O3 catalysts,prepared with the support treated with 100 g/L NH_4NO3 aqueous solution,the CO conversion,the CH_4 selectivity,and the C_(5 )selectivity were 83.13%,6.86% and 82.75% respectively,and the chain growth probability was 0.83 under the condition of 493 K,1.5 MPa,500 h~(-1)and the molar ratio of H_2 to CO being 2.0 in feed.     

Effects of ultrasonic impregnation combined with calcination in N_2 atmosphere on the property of Co_3O_4/CeO_2 composites for catalytic methane combustion

Co_3O_4/CeO_2 composites with high surface areas and ultrafine crystalline sizes for catalytic combustion of methane were firstly prepared by a new sol-gel method which combined ultrasonic impregnation treatment and calcination in N_2 atmosphere. The samples were characterized by various means such as nitrogen adsorption/desorption, X-ray diffraction(XRD), H_2 temperature-programmed reduction(H_2-TPR),X-ray photoelectron spectroscopy(XPS) and transmission electron microscopy(TEM). Results showed that the modified catalyst had the mesoporous structure, comparatively higher amount of surface oxygen and larger oxygen vacancies than others. As a result of the structure and surface composition merits, a high methane combustion conversion(50%) could be obtained at a low temperature of 262 °C for the modified Co_3O_4/CeO_2 composites catalysts. The experimental results demonstrated that ultrasonic impregnation treatment combined with the N_2 thermal treatment prior to calcination in air had a promising application for preparation of Co_3O_4/CeO_2 composites catalysts for low-temperature catalytic combustion of methane.     

Thermodynamic analysis of combined reforming process using Gibbs energy minimization method: In view of solid carbon formation

Thermodynamic analysis was applied to study combined partial oxidation and carbon dioxide reforming of methane in view of carbon formation. The equilibrium calculations employing the Gibbs energy minimization were performed upon wide ranges of pressure (1-25 atm), temperature (600-1300 K), carbon dioxide to methane ratio (0-2) and oxygen to methane ratio (0-1). The thermodynamic results were compared with the results obtained over a Ru supported catalyst. The results revealed that by increasing the reaction pressure methane conversion decreased. Also it was found that the atmospheric pressure is the preferable pressure for both dry reforming and partial oxidation of methane and increasing the temperature caused increases in both activity of carbon and conversion of methane. The results clearly showed that the addition of O 2 to the feed mixture could lead to a reduction of carbon deposition.     

Nickel ferrite spinel as catalyst precursor in the dry reforming of methane:Synthesis,characterization and catalytic properties

Dry reforming of methane by CO2 using nickel ferrite as precursor of catalysts was investigated.Nickel ferrite crystalline particles were prepared by coprecipitation of nitrates with NaOH or ammonia followed by calcination,or by hydrothermal synthesis without calcination step.The textural and structural properties were determined by a number of analysis methods,including X-ray diffraction (XRD),Raman spectroscopy and X-ray photoelectron spectroscopy (XPS),among which X-ray diffraction (XRD) was at room and variable temperatures.All synthesized oxides showed the presence of micro or nanoparticles of NiFe2O4 inverse spinel,but Fe2O3 (hematite) was also present when ammonia was used for coprecipitation.The reducibility by hydrogen was studied by temperature-programmed reduction (TPR) and in situ XRD,which showed the influence of the preparation method.The surface area (BET),particle size (Rietveld refinement),as well as surface Ni/Fe atomic ratio (XPS) and the behavior upon reduction varied according to the synthesis method.The catalytic reactivity was investigated using isopropanol decomposition to determine the acid/base properties.The catalytic performance of methane reforming with CO2 was measured with and without the pre-treatment of catalysts under H2 in 650-800 C range.The catalytic conversions of methane and CO2 were quite low but they increased when the catalysts were pre-reduced.A significant contribution of reverse water gas shift reaction accounted for the low values of H2 /CO ratio.No coking was observed as shown by the reoxidation step performed after the catalytic reactions.The possible formation of nickel-iron alloy observed during the study of reducibility by hydrogen was invoked to account for the catalytic behavior.     

CO2 reforming of methane over nickel catalysts supported on nanocrystalline MgAl2O4 with high surface area

In this paper dry reforming of methane (DRM) was carried out over nanocrystalline MgAl2O4-supported Ni catalysts with various Ni loadings. Nanocrystalline MgAl2O4 spinel with high specific surface area was synthesized by a co-precipitation method with the addition of pluronic P123 triblock copolymer as surfactant, and employed as catalyst support. The prepared samples were characterized by X-ray diffraction (XRD), N2 adsorption, H2 chemisorption, temperature-programmed reduction (TPR), temperature-programmed oxidation (TPO), temperature- programmed desorption (TPD) and transmission and scanning electron microscopies (TEM, SEM) techniques. The obtained results showed that the catalyst support has a nanocrystalline structure (crystal size: about 5 nm) with a high specific surface area (175 m2 g-1) and a mesoporous structure. Increasing in nickel content decreased the specific surface area and nickel dispersion. The prepared catalysts showed high catalytic activity and stability during the reaction. SEM analysis revealed that whisker type carbon deposited over the spent catalysts and increasing in nickel loading increased the amount of deposited carbon. The nickel catalyst with 7 wt% of nickel showed the highest catalytic activity.     

Fischer–Tropsch synthesis on impregnated cobalt-based catalysts:New insights into the effect of impregnation solutions and pH value

The Co-based catalysts were prepared with different cobalt acetate solutions. Effects of p H value were studied deeply on Fischer–Tropsch synthesis(FTS) through a semi-batch reactor. Among all impregnation solutions(water, butanol, amyl alcohol, acetic acid, nitric acid and ammonium nitrate), the catalyst prepared by NH_4NO_3 solution showed the highest catalytic activity due to its small particle size and high reduction degree. However, the catalyst with the smallest particle size derived from water as impregnation solution exhibited low activity as well as high methane selectivity since it was difficult to be reduced and inactive in FTS. According to FT-IR spectra results, the low intensity of absorbed CO on the catalyst prepared from water solution resulted in low FTS activity. Whereas, the high activity of catalysts prepared from NH_4NO_3 solution could be explained by the high intensity of absorbed CO on the catalysts.The cobalt species on the catalysts prepared under lower p H conditions exhibited smaller particle size distribution as well as lower CO conversion than those prepared at higher p H value.     

Additive effects of alkaline-earth metals and nickel on the performance of Co/γ-Al_2O_3 in methane catalytic partial oxidation

Nano-sized γ-alumina (γ-Al2O3) was first prepared by a precipitation method. Then, active component of cobalt and a series of alkaline- earth metal promoters or nickel (Ni) with different contents were loaded on the γ-Al2O3 support. The catalysts were characterized by N2 adsorption-desorption, X-ray diffraction (XRD) and thermogravimetry analysis (TGA). The activity and selectivity of the catalysts in catalytic partial oxidation (CPO) of methane have been compared with Co/γ-Al2O3, and it is found that the catalytic activity, selectivity, and stability are enhanced by the addition of alkaline-earth metals and nickel. The optimal loadings of strontium (Sr) and Ni were 6 and 4 wt%, respectively. This finding will be helpful in designing the trimetallic Co-Ni-Sr/γ-Al2O3 catalysts with high performance in CPO of methane.     

Studies on the Performance and Structure of Supported Catalysts for the Partial Oxidation of Methane to Syngas

The catalytic properties of several supported metal catalysts on different carriers were studied in the partial oxidation of methane (POM) to syngas. In our experiment, supported noble metal catalysts exhibited better performance than the other supported transition metal catalysts. The catalyst performances were significantly influenced by the d-electron configuration of the active metal components and the dispersion of active metal components on the support. A catalyst with a moderate number of unpaired electrons in the d-orbital of the active metal support without obvious acidity or redox activity (e.g. MgO) was suitable for POM performance. The Rh/SiO2 catalyst was the best in the POM reaction, among those investigated. Reaction conditions apparently also affected the POM performance of the catalyst. The conversion of methane and the selectivity for CO increased with the reaction temperature, and a high CH4/O2 ratio was not beneficial for POM performance.     

CeO2 as the Oxygen Carrier for Partial Oxidation of Methane to Synthesis Gas in Molten Salts： Thermodynamic Analysis and Experimental Investigation

A new technique -- the direct partial oxidation of methane to synthesis gas using lattice oxygen in molten salts medium has been introduced. Using CeO2 as the oxygen carrier, thermodynamic data were calculated in the reaction process, and the results indicated that direct partial oxidation of methane to synthesis gas using lattice oxygen of cerium oxide is feasible in theory. In a stainless steel reactor, the effects of temperature and varying amounts of γ-Al2O3 supported CeO2 on cn4 conversion, H2 and CO selectivity, were investigated, respectively. The results show that 10% CeO2/γ-Al2O3 has the maximal reaction activity at a temperature of 865 ℃ and above, the H2/CO ratio in the gas that has been produced reaches 2 and the CH4 conversion, H2 and CO selectivity reached the following percentages： i.e. 61%, 89%, and 91% at 870 ℃, respectively. In addition, increase of reaction temperature is favorable for the partial oxidation of methane.     

EFFECT OF Y_2O_3 ON THE PROPERTY OF NiO/Al_2O_3 CATALYST FOR PARTIAL OXIDATION OF METHANE

The effects of Y_2O_3 on the property of NiO/Al_2O_3 catalyst forcatalytic partial oxidation of methane were investigated in a continuous flowfixed bed reactor(20 mm i.d.,860 mm long).The catalysts werecharacterized by XRD and pore measurement.For comparison,similar studieswere carried out for the catalysts loaded with Zr or W oxide.The results showthat different additives and impregnating methods could greatly affect thedispersion of component Ni.The catalytic activity,the selectivity to CO andthe stability are improved because of the less facile interation between thesupport and nickel oxide,greater surface area and better dispersion of metalNi for NiO/Al_2O_3 catalyst modified by Y_2O_3.     

One-step synthesis of dimethyl ether from syngas on ordered mesoporous copper incorporated alumina

Ordered mesoporous copper incorporated Al_2O_3(Cu/Al_2O_3) with high Cu dispersion were prepared by a facile solution combustion synthesis method using aluminum nitrate and copper nitrate as oxidants and urea as fuel. It is a facile and green route to synthesize catalysts for dimethyl ether directly from syngas. Cu/Al_2O_3 catalysts were characterized by XRD, N_2 adsorption–desorption, SEM-EDS, and H_2-TPR.The results indicate that the catalysts obtain an ordered mesoporous structure and copper is homogenously dispersed. The mesoporous Cu/Al_2O_3 catalysts were utilized as bifunctional catalysts in syngas to dimethyl ether reaction(STD). The copper content affects the catalytic performance in STD reaction. The CO conversion and DME selectivity of Cu/Al_2O_3 with 15% copper molar ratio achieve 52.9% and 66.1%,respectively. Moreover, the mesoporous Cu/Al_2O_3 catalysts show excellent stability in STD reaction.     

Synthesis Gas Production from Natural Gas on Supported Pt Catalysts

Auto-thermal reforming of methane, combining partial oxidation and reforming of methane with CO2 or steam, was carried out with Pt/Al2O3, Pt/ZrO2 and Pt/CeO2 catalysts, in a temperature range of 300-900℃. The auto-thermal reforming occurs in two simultaneous stages, namely, total combustion of methane and reforming of the unconverted methane with steam and CO2, with the O2 conversion of 100% starting from 450 ℃. For combination with CO2 reforming, the Pt/CeO2 catalyst showed the lowest initial activity at 800 ℃, and the highest stability over 40 h on-stream. This catalyst also presented the best performance for the reaction with steam at 800 ℃. The higher resistance to coke formation of the catalyst supported on ceria is due to the metal-support interactions and the higher mobility of oxygen in the oxide lattice.     

Effect of Copper Substitution and Preparation Methods on the LaMnO3 Structure and Catalysis of Methane Combustion and CO Oxidation

 LaMn1-xCuxO3刡冊 perovskite oxides (x = 0, 0.2, 0.4, 0.6, 0.8, 1) were prepared by two different methods, the Pechini and sol-gel methods. The catalysts were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy (SEM), energy-dispersive spectroscopy (EDS), X-ray fluorescence spectroscopy, N2 adsorption, and temperature-programmed reduction. Their catalytic activity in the oxidation of methane and CO was evaluated. EDS and SEM results showed that the Pechini samples had more homogeneity and smaller particles (higher specific surface area). The catalytic activity for methane combustion was highest for x = 0.2. In CO oxidation, the oxides with x = 0.2 and x = 0.4 were the most active. The Pechini samples had higher activity and stability than the sol-gel samples.