微量聚四氢呋喃-聚甲基丙烯酸甲酯/聚四氢呋喃共混体系稀固体溶液中共聚物胶束的抑制成核作用

 本工作将Leibler、Whitmore和Mayes等近期关于非晶嵌段共聚物共混体系胶束理论应用于结晶嵌段共聚物共混体系的熔融态,对聚甲基丙烯酸甲酯-聚四氢呋喃两嵌段共聚物与聚四氢呋喃均聚物共混体系的结晶行为进行了研究.结果表明,很低的共聚物浓度(如1％),其胶束在共混体系的结晶过程中即可显著地起到抑制成核的作用.这对改善结晶均聚物的形态及性能有一定的应用价值.     

聚甲基丙烯酸甲酯－聚四氢呋喃两嵌段共聚物／聚四氢呋喃共混体系的相容性和结晶行为

报道了对嵌段共聚物结晶型共混体系结晶行为的研究．通过对聚甲基丙烯酸甲酯－聚四氢呋喃两嵌段共聚物／聚四氢呋喃共混体系的研究，我们发现１．微相分离结构的存在，可使相容的这类体系形成多种特殊的结晶形态；２．共混体系的相容性可以方便地由其结晶行为来判断；３．共混体系中共聚物的结晶能力显著提高．这些特点都明显不同于一般的聚合物共混体系．     

微量PEO-PS-PEO/PEO共混体系结晶过程中共聚物胶束的成核作用

本工作将Leibler等近期关于含非晶两嵌段共聚物“稀固体溶液”的胶束理论推广并应用到含结晶三嵌段共聚物的“稀固体溶液”.对微量聚氧化乙烯-聚苯乙烯-聚氧化乙烯三嵌段共聚物/聚氧化乙烯均聚物共混体系的结晶行为进行了研究.结果表明,共聚物胶束在共混体系的结晶过程中可以起到成核剂的作用.这对改善结晶均聚物的性能具有一定的应用价值.     

微量PEO-PS-PEO/PEO共混体系结晶过程中共聚物胶束的成核作用

 本工作将Leibler等近期关于含非晶两嵌段共聚物“稀固体溶液”的胶束理论推广并应用到含结晶三嵌段共聚物的“稀固体溶液”.对微量聚氧化乙烯-聚苯乙烯-聚氧化乙烯三嵌段共聚物/聚氧化乙烯均聚物共混体系的结晶行为进行了研究.结果表明,共聚物胶束在共混体系的结晶过程中可以起到成核剂的作用.这对改善结晶均聚物的性能具有一定的应用价值.     

聚四氢呋喃-聚甲基丙烯酸甲酯两嵌段共聚物的结晶行为

报导了系列聚四氢呋喃-聚甲基丙烯酸甲酯结晶-非晶(硬段型)两嵌段共聚物的结晶行为，结果表明，其微相分离和结晶规律与文献上唯一进行过系统研究的同类嵌段共聚物(PEO－b－PS)都有较大的差别；结晶段结晶能力的大小是制约这类体系微相分离和结晶规律的一个重要因素．     

聚氧化乙烯-聚苯乙烯-聚氧化乙烯三嵌段共聚物/聚苯醚共混物的相容性和结晶行为

本工作对聚氧化乙烯-聚苯乙烯-聚氧化乙烯(PEO-PS-PEO)三嵌段共聚物与聚苯醚(PPO)均聚物共混物的相容性及结晶行为进行了研究。结果表明,共混体系的相容性与嵌段共聚物中苯乙烯段的含量有关,PS含量越高,PPO与共聚物PS段的相容性越好。共混体系的结晶行为也明显不同于一般均聚物共混体系。在DSC降温结晶过程中最多可出现三个结晶峰。     

聚氧化乙烯-聚苯乙烯-聚氧化乙烯三嵌段共聚物/聚苯醚共混物的相容性和结晶行为

 本工作对聚氧化乙烯-聚苯乙烯-聚氧化乙烯(PEO-PS-PEO)三嵌段共聚物与聚苯醚(PPO)均聚物共混物的相容性及结晶行为进行了研究。结果表明,共混体系的相容性与嵌段共聚物中苯乙烯段的含量有关,PS含量越高,PPO与共聚物PS段的相容性越好。共混体系的结晶行为也明显不同于一般均聚物共混体系。在DSC降温结晶过程中最多可出现三个结晶峰。     

在含嵌段共聚物的“稳固体溶液”中决定共聚物胶束作用的诸因素

在含嵌段共聚物可结晶型“稀固体溶液”的结晶过程中,我们已发现共聚物胶束既可起着成核剂的作用,也可起抑制成核数目的作用.本文根据进一步的研究结果,论述了共聚物胶束是起着成核剂的作用,还是起抑制成核作用或对体系的成核行为无影响主要取决于共聚物和均聚物的相对结晶能力及共混体系的相容性.     

聚二甲基硅氧烷与聚四氢呋喃三嵌段共聚物的合成表征与性能

通过可控/活性正离子开环聚合设计合成一系列不同分子量的聚四氢呋喃活性链,利用聚二甲基硅氧烷(PDMS)的双端胺基与反应制备PDMS与聚四氢呋喃(PTHF)的新型三嵌段共聚物(PTHF-b-PDMS-b-PTHF).通过FTIR与1H-NMR表征产物化学结构及共聚组成,由TGA、DSC及DMA研究嵌段共聚物热性能与动态力学性能,采用TEM和in situ POM观察嵌段共聚物的微观形态与结晶形态.常温下表征共聚物材料自修复性能及37°C下表征其抗菌性能.结果表明:采用体系引发四氢呋喃可控/活性正离子开环聚合制备预期分子量的,进一步与双端胺基官能化PDMS反应,反应效率可达95%左右,设计合成出一系列不同共聚组成的PTHF-b-PDMS-b-PTHF三嵌段共聚物.该共聚物呈现双连续微观相分离结构和结晶现象,随着PTHF链段的增长,结晶速率加快;与相同分子量均聚PDMS和PTHF相比,所制备的三嵌段共聚物的热稳定性明显提高;三嵌段共聚物链中存在2个―NH―基团,在分子链间形成氢键导致产生物理交联及聚合物网络,使材料具有较好的弹性、柔韧性和强度,同时具有自修复特性,将材料完全切开,常温下24 h后断面发生良好愈合,在应力作用下可被拉伸至原长的1.5倍;原位制备的三嵌段共聚物/银纳米复合材料对大肠杆菌表现出良好的抗菌性能.基于可控/活性正离子开环聚合方法合成的PTHF-b-PDMS-b-PTHF三嵌段共聚物/银纳米复合材料兼具PTHF、PDMS及纳米银的优良性能,在生物医用材料领域具有应用前景.     

嵌段共聚物／均聚物共混体系的微相分离和形态结构研究

着重介绍嵌段共聚物／均聚物共混体系的微相分离，微胶束的形成，微区的形态结构以及形态的控制。     

新型温度敏感性自组装胶束P(NiPAAm-co-DMAA)-co-P(L-Ala)的合成和性能

通过原子转移自由基聚合(ATRP)合成了一种带有活性—NH2基团的温度敏感性亲水型共聚物P(NiPAAm-co-DMAA), 并将其作为引发剂, 合成了P(NiPAAm-co-DMAA)-co-P(L-Ala), 其分子量分布(PDI)在1.3左右. 聚合物通过自组装形成纳米胶束. 透射电镜(TEM)结果表明, 胶束大小200~300 nm, 具有明显的核壳结构. 共聚物的最低临界溶解温度(LCST)为45.5 ℃. 温度低于LCST时, 聚合物溶解形成胶束; 高于LCST时, 胶束解离, 聚合物不溶. 聚合物对温度的响应是快速而可逆的.     

Aggregation of poly(ethylene oxide)-poly(propylene oxide) block copolymers in aqueous solution: DPD simulation study

The dissipative particle dynamics (DPD) simulation method was applied to simulate the aggregation behavior of three block copolymers, (EO)16(PO)18, (EO)8(PO)18(EO)8, and (PO)9(EO)16(PO)9, in aqueous solutions. The results showed that the size of the micelle increased with increasing concentration. The diblock copolymer (EO)16(PO)18 would form an intercluster micelle at a certain concentration range, besides the traditional aggregates (spherical micelle, cylindrical micelle, and lamellar phase); while the triblock copolymer (EO)8(PO)18(EO)8 would form a spherical micelle, cylindrical micelle, and lamellar phase with increasing concentration, and (PO)9(EO)16(PO)9 would form intercluster aggregates, as well as a spherical micelle and gel. New mechanisms were given to explain the two kinds of intercluster micelle formed by the different copolymers. It is deduced from the end-to-end distance that the morphologies of the diblock copolymer and triblock copolymer with hydrophilic ends were more extendible than the triblock copolymer with hydrophobic ends.     

Conventional synthesis of amphiphilic block copolymer utilized for polymeric micelle by mechanochemical solid-state polymerization

The first example is presented here of an amiphiphilic block copolymer synthesized by mechanochemical solid-state polymerization and used to form polymeric micelles. A model amphiphilic block copolymer was synthesized first, possessing galactose as a hydrophilic side chain and theophylline as a hydrophobic side chain, by mechanochemical solid-state polymerization. The resulting copolymer had a narrow molecular weight distribution. Polymeric micelle formation was subsequently carried out with the copolymer by a dialysis method. To gain insight into the physicochemical properties of the polymeric micelle, dynamic light scattering (DLS) measurements were performed. A narrow distribution of diameters was observed in the polymeric micelle solution, and these micelles were disrupted by the addition of sodium dodecyl sulfate (SDS). It was also confirmed by DLS measurements that the polymeric micelles were spherical. These results suggested that the block copolymer synthesized by mechanochemical solid-state polymerization was as suitable for the preparation of polymeric micelles as materials obtained by living polymerization.     

Novel pH sensitive block copolymer micelles for solvent free drug loading

Novel pH sensitive biodegradable block copolymers (MPEG-PDLLA-OSM) composed of mono-methoxy poly(ethylene glycol) (MPEG), poly (D,L-lactide) (PDLLA) and sulfamethazine oligomer (OSM) were synthesized via ring-opening polymerization and a dicyclohexyl carboimide (DCC) coupling reaction. These copolymers had a relatively low critical micelle concentration (CMC) due to the strong hydrophobic properties of non-ionized OSM at pH 7.0. Also, the pH sensitive block copolymers showed the micelle-unimer transition due to the ionization-non-ionization of OSM in the pH range (pH 7.2-8.4) above the CMC. Due to the pH sensitive properties of the block copolymer, the hydrophobic drug paclitaxel (PTX) was incorporated into a pH sensitive block copolymer micelle by the pH induced micellization method, without using an organic solvent. The block copolymer micelle prepared by pH induced micellization showed a relatively high PTX loading efficiency, and good stability for 2 d at 37 degrees C. Furthermore, the PTX loaded micelle showed a sustained release of PTX with a small burst in vitro over 2 d. The present results suggest that the pH induced micellization method due to the micelle-unimer transition of the pH sensitive block copolymer would be a novel and valuable drug incorporation tool for hydrophobic and protein drugs, since no organic solvent is involved in the formulation.     

Micellization behavior of star-block copolymers in a selective solvent: A Brownian dynamics simulation approach

Micellization behavior of (AB)n type star-block copolymer in a selective solvent for its outer block is investigated by using a Brownian dynamics simulation. Micellar properties are compared in terms of the arm number (n) of star-block copolymer. It is observed that the critical micelle concentration (cmc) shows a minimum when the cmc is plotted against the arm number. The star-block copolymer with longer soluble block shows the cmc minimum at smaller arm number than that with shorter soluble block. Although the star-block copolymer with multiple arms forms more compact core as compared to diblock copolymer, the average aggregation number is inversely proportional to the arm number (approximately 1/n), which implies that the micelle size is invariant with the arm number. Theoretical predictions based on a simple mean field theory agree qualitatively well with the simulation results.     

含嵌段共聚物“稀固体溶液”中共聚物胶束核的结晶行为

报道了含嵌段共聚物的可结晶型稀固体溶液中，不同共聚物胶束的结晶行为不同；结晶段形成胶束壳和形成胶束核，其结晶行为也相差很大。     

Synthesis and micellization of amphiphilic poly(sebacic anhydride)–poly(ethylene glycol)–poly(sebacic anhydride) block copolymers

Amphiphilic biodegradable block copolymers [poly(sebacic anhydride)–poly(ethylene glycol)–poly(sebacic anhydride)] were synthesized by the melt polycondensation of poly(ethylene glycol) and sebacic anhydride prepolymers. The chemical structure, crystalline nature, and phase behavior of the resulting copolymers were characterized with ¹H NMR, Fourier transform infrared, gel permeation chromatography, and differential scanning calorimetry. Microphase separation of the copolymers occurred, and the crystallinity of the poly(sebacic anhydride) (PSA) blocks diminished when the sebacic anhydride unit content in the copolymer was only 21.6%. ¹H NMR spectra carried out in CDCl₃ and D₂O were used to demonstrate the existence of hydrophobic PSA domains as the core of the micelle. In aqueous media, the copolymers formed micelles after precipitation from water‐miscible solvents. The effects on the micelle sizes due to the micelle preparation conditions, such as the organic phase, dropping rate of the polymer organic solution into the aqueous phase, and copolymer concentrations in the organic phase, were studied. There was an increase in the micelle size as the molecular weight of the PSA block was increased. The diameters of the copolymer micelles were also found to increase as the concentration of the copolymer dissolved in the organic phase was increased, and the dependence of the micelle diameters on the concentration of the copolymer varied with the copolymer composition. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1271–1278, 2006     

Deformation of copolymer micelles induced by amphiphilic dimer particles

Combining self-consistent-field theory and density-functional theory,we systematically study the deformation of copolymer micelles induced by the presence of amphiphilic dimer particles.Due to the amphiphilic nature,dimer particles tend to accumulate onto the interface of the copolymer micelle.With increasing concentration of the symmetric dimer particles,which are made of two identical spherical particles,the micelle deforms from the initial sphere to ellipse,dumbbell, and finally separates into two micelles.Furthermore,asymmetric dimer particles,composed by two particles with different sizes,are considered to investigate the influence of geometry of dimer particles on the deformation of the micelle.It is found that the micelle inclines to deform into dumbbell due to the additional curvature originating in the gathering of asymmetric dimer particles onto the interface of the micelle.The present study on the deformation of micelles is useful to understand the possible shape variation in the course of cell division/fusion.     

嵌段共聚物/均聚物共混体系的结晶行为 I. 非球状共聚物胶束的作用

将Leibler, Whitmore和Mayes等近期关于非晶嵌段共聚物“稀固体溶液”的理论应用于嵌段聚共聚物结晶型“稀固体溶液”结晶行为的研究。发现球状共聚物胶束既可起成核剂作用, 也可起抑制成核作用。报导了当共聚物胶束由球形变为非球形时, 共聚物胶束的上述作用都会发生较大的变化, 并根据Leibler和Mayes分别提出的球形和非球形胶束理论解释了这一实验现象。