Enhancement of visible-light photocatalytic activity of Cu-doped TiO<Subscript>2</Subscript> nanoparticles

Bare TiO₂ and Cu-doped TiO₂ nanoparticles with different nominal doping amounts of Cu ranging from of 0.5 to 5.0 mol% were synthesized using the modified sol–gel method. The samples were physically characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, energy-dispersive X-ray spectroscopy, Brunauer–Emmett–Teller-specific surface area, UV–Vis diffuse reflectance spectroscopy, zeta potential, X-ray photoelectron spectroscopy, inductively coupled plasma, and photoluminescence techniques. The Cu-doped TiO₂ exhibited good photocatalytic activity in mineralization of oxalic acid and formic acid under visible light irradiation. Photomineralization of oxalic and formic acids under visible light irradiation revealed greatly enhanced photoactivity exhibited by the 2.0 mol% Cu-doped TiO₂ photocatalyst compared to bare TiO₂ . The enhanced photocatalytic performance arises from copper ion doping in the TiO₂ structure, leading to an extended photoresponsive range, enhanced photogenerated charge separation, and transportation efficiency.     

Preparation of ZnFe<Subscript>2</Subscript>O<Subscript>4</Subscript> nanoparticles by mechanical alloying and annealing for sensitizing C-modified TiO<Subscript>2</Subscript> and acquirement of efficient photocatalyst

ZnFe₂O₄ nanoparticles sensitized by C-modified TiO₂ hybrids (ZnFe₂O₄–TiO₂/C) were successfully prepared by a feasible method. The ZnFe₂O₄ nanoparticles were prepared by mechanical alloying and annealing. The residual organic compounds in the synthetic process of TiO₂ were selected as the carbon source. The as-prepared composites were characterized by X-ray diffraction, Raman spectroscopy, X-ray fluorescence, transmission electron microscopy, X-ray photoelectron spectroscopy, ultraviolet–visible light diffuse reflectance spectroscopy (UV–Vis) and N₂ adsorption–desorption analysis. The photocatalytic activity of the photocatalysts was measured by degradation of methyl orange under ultraviolet (UV) light and simulated solar irradiation, respectively. The results show that the carbon did not enter the TiO₂ lattice but adhered to the surface of TiO₂. The photocatalytic activity of the as-prepared C-modified TiO₂ (TiO₂/C) improved both under UV and simulated solar light irradiation, but the improvement was not dramatic. Introduction of ZnFe₂O₄ into the TiO₂/C could enhance the absorption spectrum range. The ZnFe₂O₄–TiO₂/C hybrids exhibited a higher photocatalytic activity both than that of the pure TiO₂ and TiO₂/C under either UV or simulated solar light irradiation. The complex synergistic effect plays an important role in improving the photocatalytic performance of ZnFe₂O₄–TiO₂/C composites. The optimum photocatalytic performance was obtained from the ZnFe₂O₄(0.8 wt%)–TiO₂/C sample.     

Enhancement of photocatalytic H<Subscript>2</Subscript> evolution over TiO<Subscript>2</Subscript> nano-sheet films by surface loading NiS nanoparticles

NiS/TiO₂ nano-sheet films (NiS/TiO₂ NSFs) photocatalysts were prepared by loading NiS nanoparticles as noble metal-free cocatalysts on the surface of TiO₂ films through a solvothermal method. The prepared samples were characterized by XRD, SEM, EDS, UV–Vis absorption spectra and XPS analysis. The photocatalytic H₂ evolution and photoluminescence spectroscopy (PL) experiments indicated that the NiS cocatalysts could efficiently promote the separation of photogenerated charge carriers in TiO₂ and consequently enhance the H₂ evolution activity. The hydrogen yield obtained from the optimal sample reached 4.31 μmol cm^–2 at 3.0 h and the corresponding energy efficiency was about 0.26%, which was 21 times higher than that of pure TiO₂ NSF. A possible photocatalytic mechanism of NiS cocatalyst on the improvement of the photocatalytic performance of TiO₂ NSF was also proposed.     

Preparation of nanocrystalline TiO<Subscript>2</Subscript> powders for photocatalytic oxidation of phenol

Nanocrystalline TiO₂ powders in the anatase, rutile, and mixed phases prepared by hydrolysis of TiCl₄ solution were of ultrafine size (<7.2 nm) with high specific surface areas in the range 167 to 388 m²/g. In the photocatalytic degradation of phenol as model reaction, the photocatalytic properties of TiO₂ nanoparticles were evaluated by use of UV–vis absorption spectroscopy and total organic carbon (TOC) content. The synthetic mixed-phase TiO₂ powder calcined at 400 °C had higher activity than pure anatase or rutile; it degraded more than 90% phenol to CO₂ (evaluated by TOC) after irradiation with near UV light for 90 min at a catalyst loading of 0.4 g/L. The TOC results indicated that rutile TiO₂ crystallites of particle size 7.2 nm resulted in much better photocatalytic performance than particles of larger size. This result suggested that some intermediates, not determined by UV–vis absorption spectroscopy, existed in the solution after the photocatalytic process over the rutile TiO₂ photocatalysts of larger crystallite size.     

TiO<Subscript>2</Subscript>/SiO<Subscript>2</Subscript> hybrid nanomaterials: synthesis and variable UV-blocking properties

Silica and core–shell structured titania/silica (TiO₂/SiO₂) nanoparticles with particles size ranging from tens to hundreds of nanometers were prepared and deposited onto cotton fabric substrates by sol–gel process. The morphologies of the nanoparticles were characterized by field-emission scanning electron microscope (FE-SEM). The photocatalytic decomposition properties as well as UV-blocking properties of the fabrics treated with SiO₂ and TiO₂/SiO₂ nanoparticles were investigated.     

Preparation and photocatalytic activity of TiO<Subscript>2</Subscript> films with Ni nanoparticles

Titania thin films were synthesized by sol–gel dip-coating method with metallic Ni nanoparticles synthesized separately from an organometallic precursor Ni(COD)₂ (COD = cycloocta-1,5-diene) in presence of 1,3-diaminopropane as a stabilizer. Titania was obtained from a titanium isopropoxide precursor solution in presence of acetic acid. A Ni/TiO₂ sol system was used to coat glass substrate spheres (6, 4 and 3 mm diameter sizes), and further heat treatment at 400 °C was carried out to promote the crystallization of titania. XRD analysis of the TiO₂ films revealed the crystallization of the anatase phase. Transmission Electron Microscopy (TEM) and High Resolution TEM studies of Ni nanoparticles before mixing with the TiO₂ solution revealed the formation of Ni nanostructures with an average size of 5–10 nm. High-angle annular dark-field images of the Ni/TiO₂ system revealed well-dispersed Ni nanoparticles supported on TiO₂ and confirmed by AFM analysis. The photocatalytic activity of the Ni/TiO₂ films was evaluated in hydrogen evolution from the decomposition of ethanol using a mercury lamp for UV light irradiation. Titania films in presence of Ni nanoparticles show higher efficiency in their photocatalytic properties in comparison with TiO₂.     

Cooperation among N,F and Fe in tri-doped TiO<Subscript>2</Subscript> photocatalyst

TiO₂ photocatalysts tri-doped with N, F and Fe were synthesized by a sol–gel method. The cooperation of N, F and Fe in tri-doped TiO₂ was verified by monitoring NH₃ decomposition, X-ray diffraction (XRD), scanning electron microscopy (SEM), high-resolution transmission electron microscopy (HRTEM), X-ray photoelectron spectroscopy (XPS) and ultraviolet–visible (UV–Vis) absorption spectroscopy, and by the simulation based on the density functional theory (DFT). The results from NH₃ decomposition revealed that the cooperation of N, F and Fe broadened the optical response of TiO₂ to the visible light range and also enhanced the photocatalytic activity of TiO₂ under UV light. The reusability of the tri-doped TiO₂ sample after three cycles under UV and visible light irradiation was very good. XRD patterns and SEM and HRTEM images indicated that the tri-doped sample was nanometric anatase with a small amount of rutile with an average particle size of 18 nm. Tri-doping with N, F and Fe suppressed the phase transition from anatase to rutile and also resulted in some more lattice defects. XPS analysis showed that the N, F and Fe atoms were doped into the TiO₂ lattice. UV–Vis absorption spectra of the tri-doped TiO₂ showed that its optical absorption edge was moved up to 640 nm and its UV absorption was also enhanced. The DFT results confirmed that the cooperation of Fe 3d and N 2p orbits narrowed the band gap of TiO₂ and the F 2p orbit broadened the upper valence bands. The synergistic electron density around N, F and Fe in tri-doped TiO₂ was capable of enhancing the photochemical stability and reusability of TiO₂.     

Heterostructured CoO/3D-TiO<Subscript>2</Subscript> nanorod arrays for photoelectrochemical water splitting hydrogen production

Homogeneous p-type cobalt (II) oxide (CoO) nanoparticles were successfully deposited on n-type three-dimensional branched TiO₂ nanorod arrays (3D-TiO₂) through photochemical deposition and thermal decomposition to form a novel CoO/3D-TiO₂ p-n heterojunction nanocomposite. Due to the narrow band gap of CoO nanoparticles (~2.4 eV), the as-synthesized CoO/3D-TiO₂ exhibited an excellent visible light absorption. The amounts of deposited CoO nanoparticles obviously influence the hydrogen production rate in the photoelectrochemical (PEC) water splitting. The as-synthesized CoO/3D-TiO₂-5 obtains the highest PEC hydrogen production rate of 0.54 mL h^?1 cm^?2 after five-time CoO deposition cycles (at a potential of 0.0 V vs Ag/AgCl). The photocurrent density of CoO/3D-TiO₂-5 is 1.68 mA cm^?1, which is ca. 2.5 times greater than that of pure 3D-TiO₂. The results showed that the formation of internal electrical-field between the CoO/3D-TiO₂ heterojunction, which has a direction from n-type TiO₂ to p-type CoO, facilitated the charge separation and transfer and resulted in a high efficiency and stable PEC activity.     

Preparation of TiO<Subscript>2</Subscript> nanofibers immobilized on quartz substrate by electrospinning for photocatalytic degradation of ranitidine

The photocatalytic activity of TiO₂ nanofibers immobilized on quartz substrates was investigated by evaluating the decomposition of organic pollutants. TiO₂ nanofibers were synthesized by electrospinning the Ti-precursor/polymer mixture solution, followed by hot-pressing for enhancing the adhesion of TiO₂-nanofiber films to the substrates. TiO₂ started to crystalize in the anatase form at 500 °C and reached the optimal photocatalytic anatase/rutile phase ratio of 70:30 at a calcination temperature of 600 °C. The TiO₂-nanofiber film was demonstrated to be an efficient photocatalyst by ranitidine decomposition under UV illumination and was proven to have a comparable photocatalytic activity with the well-known Degussa P25 nanoparticulate photocatalyst and excellent recyclability during 10 cycles of photocatalytic operation, indicating no loss of TiO₂ nanofibers during photocatalytic operations.     

Synthesis and photocatalytic activity of TiO<Subscript>2</Subscript> nanoparticles fluorine-modified with TiF<Subscript>4</Subscript>

Fluorine-modified TiO₂ nan oparticles were synthesized by introducing TiF₄ as a fluorine source either before or after the sufficient hydrolysis and condensation of Ti(OEt)₄. The photocatalytic activity of the fluorine-modified catalysts was found to be greatly affected by the fluorine position in TiO₂ nanoparticles. When TiF₄ and Ti(OEt)₄ hydrolyzed with synchronization, the fluorine tended to be doped in the lattice. The formation of Ti³⁺ defects could result in charge recombination in bulk and bring down the photocatalytic activity. In contrast, if TiF₄ was introduced after the sufficient hydrolysis and condensation of Ti(OEt)₄. Ti−F bonds could exist mainly on the TiO₂ particles surface, which not only prevented the growth of anatase crystals but also facilitated the transfer of organic compounds from solution to catalyst surface by reducing the hydrophilic properties.     

Single-step solvothermal synthesis of mesoporous anatase TiO<Subscript>2</Subscript>-reduced graphene oxide nanocomposites for the abatement of organic pollutants

In the present work, we have fabricated a novel mesoporous TiO₂–rGO nanocomposite by a facile one-step solvothermal method using titanic sulfate as the TiO₂ source. The as-prepared composites were characterized by transmission electron microscopy, X-ray diffraction; UV–Vis diffuse reflectance spectra, X-ray photoelectron spectroscopy and photoluminence spectra. In situ nucleation and anchoring of TiO₂ nanoparticles onto a graphene sheet is favorable fpr forming an intimate interfacial contact, and the chemically bonded TiO₂–rGO nanocomposites commendably enhanced their photocatalytic activity in the photodegradation of rhodamine B and phenol. The high photocatalytic activity of the as-synthesized nanocomposites are primarily ascribed to the mesoporous structure, efficient charge transportation and separation with enhanced visible light absorption, which come from the appealing nanoarchitecture, for instance, ultra-dispersed and ultra-small TiO₂ nanocrystals along with intimate and absolute interfacial contact between the TiO₂ nanocrystals and the graphene sheet.     

Photocatalytic degradation of organic compounds in aqueous systems by Fe and Ho codoped TiO<Subscript>2</Subscript>

Undoped, single-doped, and codoped TiO₂ nanoparticles were prepared by the sol-gel method and characterized with X-ray diffraction (XRD), the Brunauer-Emmett-Teller (BET)-specific surface area (S_BET), UV-Vis absorption spectra (UV-Vis), and X-ray photoelectron spectroscopy (XPS). Their photocatalytic activity was evaluated by methyl orange (MO) degradation in an aqueous suspension under UV or simulated solar light illumination. XRD showed that all samples calcined at 600°C preserved the anatase structure, and doping inhibited the increase of crystallite size. The BET result revealed that doping improved the surface area of TiO₂. UV-Vis indicated that Fe³⁺-doping broadened the absorption profile of TiO₂. XPS demonstrated that doping was advantageous to absorb more surface hydroxyl groups or chemisorbed water molecules. Photocatalytic degradation showed that the photocatalytic activity of TiO₂ codoped with Fe³⁺ and Ho³⁺ ions was markedly improved. This was ascribed to the fact that there was a cooperative action in the two doped elements. Fe³⁺-doping broadens the absorption profile, improves photo utilization of TiO₂, and then generates more electronhole pairs. Ho³⁺-doping restrains the increase in grain size and retards the recombination of photo-generated electrons and holes.     

Assessment of operating parameters for photocatalytic degradation of a textile dye by Fe<Subscript>2</Subscript>O<Subscript>3</Subscript>/TiO<Subscript>2</Subscript>/clinoptilolite nanocatalyst using Taguchi experimental design

In the current study, a nanophotocatalyst doped with of TiO₂ and Fe₂O₃ nanoparticles supported on Iranian clinoptilolite was synthesized and characterized by XRD, XRF, SEM, and EDX analyses. The results suggested the successful loading of TiO₂ and Fe₂O₃ nanoparticles onto the surface of clinoptilolite. The SEM images confirmed the average size of nanoparticles deposited on zeolite, which was about 20–40 nm. Furthermore, application of the synthesized photocatalyst in photocatalytic degradation of Acid Black 172 dye was studied using the Taguchi method and the chosen parameters were as follows: pH (2–7), dye concentration (50–200 mg/l), irradiation time (30–120 min), and catalyst dosage (0.5–1.5 g/l). The results indicate that dye concentration, pH, and irradiation time are respectively the most effective factors in these experiments while with the minimum dosage of the catalyst (0.5 g/l), up to 90 % removal efficiency could be achieved. The optimum value for each parameter was pH = 2, dye concentration = 50 mg/l, catalyst dosage = 1 g/l and irradiation time = 60 min, and the dye removal efficiency reached up to 100 % at these optimal conditions. Furthermore, after five-times recycling and reusing the catalyst, the efficiency of the photocatalytic degradation was reduced from 91.5 to 65.9 %, which is still an acceptable value.     

Solvothermal preparation of copper(II) porphyrin-sensitized mesoporous TiO<Subscript>2</Subscript> composites: enhanced photocatalytic activity and stability in degradation of 4-nitrophenol

Four new copper(II) porphyrins CuPp(1, 2, 3, 4) with a different number of peripheral ester groups were synthesized and used to sensitize the mesoporous TiO₂ under solvothermal condition, and accordingly, four mesoporous CuPp(1, 2, 3, 4)/TiO₂ composites were obtained. These composites were characterized by X-ray diffraction, scanning electron microscopy, transmission electron microscopy, BET nitrogen adsorption–desorption isotherms (BET), UV–vis diffuse reflectance spectroscopy (UV–vis-DRS), and Fourier-transform infrared spectroscopy (FT-IR). The results showed the crystal structure and morphology of mesoporous TiO₂ were not affected by the porphyrin existence on its surface. The photocatalysis properties of mesoporous TiO₂ and CuPp(1, 2, 3, 4)/TiO₂ have been evaluated by conducting the photocatalytic degradation of 4-nitrophenol (4-NP) under visible-light irradiation, and the result showed their higher photocatalytic activities and the order is: CuPp(4)/TiO₂ > CuPp(3)/TiO₂ > CuPp(2)/TiO₂ > CuPp(1)/TiO₂ ? TiO₂. The probable reasons are their large surface area and different number of peripheral groups in CuPp, which separate electron–hole pairs efficiently. The repetition test of CuPp(1, 2, 3, 4)/TiO₂ composites demonstrated that they still maintained superior photocatalytic activity over six recycles.     

Bi<Subscript>2</Subscript>O<Subscript>3</Subscript>/BiFeO<Subscript>3</Subscript> heterostructure: preparation,characterization, and photocatalytic activity

Bi₂O₃/BiFeO₃ composite was successfully fabricated by a conventional sol–gel method and structural properties were characterized based on X-ray diffractometer, scanning electron microscope, transmission electron microscope, energy-dispersive X-ray analyzer, nitrogen adsorption–desorption measurement, and UV–visible diffuse reflectance spectroscopy. Bi₂O₃/BiFeO₃ had a good absorption for visible light, which was benefit to photocatalytic activity. The highest degradation efficiency was obtained when the content of Bi₂O₃ in Bi₂O₃/BiFeO₃ was 63.9%. Effect of experimental conditions was investigated, and the highest photocatalytic activity of Bi₂O₃/BiFeO₃ was observed at photocatalyst dosage of 0.5 g/L, initial BPA concentration of 10 mg/L, and solution pH of 6.3. Bi₂O₃/BiFeO₃ photocatalyst exhibited enhanced photocatalytic activity for BPA, and the reaction rate constant over Bi₂O₃/BiFeO₃ composite was 2.23, 3.65, and 8.71 times higher than that of BiFeO₃, Bi₂O₃ and commercial TiO₂ (P25), respectively. Bi₂O₃/BiFeO₃ showed high photocatalytic activity after three cycles, suggesting that it was a stable photocatalyst. The possible photocatalytic mechanism has been discussed on the basis of the theoretical calculation and the experimental results. The hydroxyl and superoxide radicals together with photogenerated holes played significant roles in the photocatalytic reaction.     

Synthesis,characterization of B-doped TiO<Subscript>2</Subscript> nanotubes with high photocatalytic activity

B-doped TiO₂ nanotubes (B/TiO₂ NTs) were prepared by the combination of sol–gel process with hydrothermal treatment. The prepared catalysts were characterized by XRD, TEM and XPS. The photocatalytic activity of B/TiO₂ NTs was evaluated through the photodegradation of aqueous methyl orange. The results demonstrated that the 1.5% B/TiO₂ NTs calcined at 300 °C possessed the best photocatalytic activity. Compared with pure TiO₂ nanotubes, the doping with B significantly enhanced the photocatalytic efficiency.     

Photocatalytic effect of nano-TiO<Subscript>2</Subscript> loaded cement on dye decolorization and <Emphasis Type="Italic">Escherichia coli</Emphasis> inactivation under UV irradiation

In the present study, titanium dioxide (TiO₂) nano-particles were synthesized by sol–gel technique and then used to provide nano-TiO₂ loaded cement samples at 1, 5, and 10 wt% for investigation of Malachite green pigment decomposition and Escherichia coli inactivation under UV irradiation. Surveys conducted on the synthesized TiO₂ nano-particles showed a 100 % anatase phase with a mean particle size of 66.5 nm, surface area of 64.352 m² g^?1, and a porosity volume of 0.1278 cm³ g^?1. Cement samples containing this catalyst exhibited stronger photocatalytic properties as compared to the same amount of pure catalyst. Considering both photocatalytic performance and cost of catalyst, 5 wt% titanium dioxide was suggested to be added to cement. By addition of 1 wt% polycarboxylic copolymer as super-plasticizer to the cement paste, the photocatalytic sample activities were reinforced so that a similar performance could be obtained at 1 wt% catalyst as compared to 5 wt% catalyst without super-plasticizer.     

A Novel NiWS-TiO<Subscript>2</Subscript>(w) Catalyst Using NiWO<Subscript>4</Subscript> Nanoparticles as Precursor with Enhanced Hydrodesulfurization Activity

In this work, NiWO₄ nanoparticles were prepared by a novel simple method and loading on the mesoporous TiO₂ whiskers (TiO₂(w)) carrier as the precursor of NiWS. In addition, the NiWS-TiO₂(w) catalysts showing high hydrodesulfurization (HDS) activity is described. The structure and chemical composition of the as-prepared samples were characterized by X-ray powder diffraction, X-ray photoelectron spectroscopy, temperature-programmed reduction, NH₃-temperature programmed desorption and transmission electron microscopy, respectively. Results indicate that smaller crystallite size and better dispersion of active NiWO₄ particles could be achieved by using TiO₂(w) as the support to disperse NiWO₄ nanoparticles. TiO₂(w) can also decrease the reduction temperature of Ni–W metal oxide and promote a highly sulfidation degree of Ni and W active sites. The obtained NiWS-TiO₂(w) catalysts show much higher dibenzothiop HDS activity than the unsupported NiWS catalyst, and the sulphur content of desulfurated oil can reach 20 ppm at the mild condition of 260 °C and 2 Mpa.     

Preparation and photoelectrochemical performance of TiO<Subscript>2</Subscript>/Ag<Subscript>2</Subscript>Se interface composite film

Coupling TiO₂ with a narrow band gap semiconductor acting as the photosensitizer has attracted much attention in solar energy exploitation. In this work, the porous TiO₂ film was first formed on the conducting glass plate (CGP) substrate by the decomposition of polyethylene glycol (PEG) mixing in titanium hydroxide sol at 450°C. Then, the TiO₂/Ag²Se interface composite film was fabricated by interface reaction of AgNO₃ with NaSeSO₃ on the activated surface of porous TiO₂ film. The results of SEM and XRD analyses indicated that the porous TiO₂ layer was made up of the anatase crystal, and the Ag₂Se layer was made up of congregative small particles that have low-temperature α-phase structure. Due to its efficient charge separation for the photo-induced electron-hole pairs, the TiO₂/Ag₂Se interface composite film as-prepared has good photovoltaic property and high photocurrent response for visible light, which have been confirmed by the photoelectrochemical measurements.     

Photocatalytic degradation of trichloroethylene on platinum ion-doped TiO<Subscript>2</Subscript> under visible light irradiation

Porous platinum ion-doped TiO₂ (Pt–TiO₂) was prepared by a sol–gel method and demonstrated to have superior photocatalytic activity for the photodegradation of gaseous trichloroethylene (TCE) under visible light (VL) irradiation from a xenon lamp equipped with 422-nm cut-off filter. Kinetic studies were performed to clarify the effect of the doping amounts, space times, VL intensity, and mole fractions of TCE, O₂, and H₂O on the degradation of TCE. Under ultraviolet (UV) irradiation, the photocatalytic activity of Pt–TiO₂ was the same as that of TiO₂, indicating that the doped Pt ion did not act as a recombination center for the photogenerated holes and electrons. Based on the kinetic data and reaction products, we conclude that the photocatalytic degradation of TCE on Pt–TiO₂ under VL irradiation proceeds similarly to TiO₂ under UV irradiation. We also performed the photocatalytic degradation of TCE at the space time of 7.5 × 10⁷ g s mol^?1 in a tubular reactor packed with the Pt–TiO₂ pellets which are more suitable than the Pt–TiO₂ powder for the practical remediation of the contaminated gas. TCE was completely degraded, i.e. 100% conversion was achieved under VL irradiation but only a small quantity of CO₂ was formed with the stoichiometric ratio of [CO₂]_formed/[TCE]_degraded of ca. 0.33. By switching the gas stream containing TCE to humid air, more CO₂ was formed, indicating that the dichloroacetates accumulated on the Pt–TiO₂ surface are photodegradable to CO₂ under VL irradiation.