A magnetic metal-organic framework as a new sorbent for solid-phase extraction of copper(II), and its determination by electrothermal AAS

We report on the synthesis of Fe₃O₄-functionalized metal-organic framework (m-MOF) composite from Zn(II) and 2-aminoterephthalic acid by a hydrothermal reaction. The magnetic composite is iso-reticular and was characterized by FTIR, X-ray diffraction, SEM, magnetization, and TGA. The m-MOF was then applied as a sorbent for the solid-phase extraction of trace levels of copper ions with subsequent quantification by electrothermal AAS. The amount of sorbent applied, the pH of the sample solution, extraction time, eluent concentration and volume, and desorption time were optimized. Under the optimum conditions, the enrichment factor is 50, and the sorption capacity of the material is 2.4 mg g^?1. The calibration plot is linear over the 0.1 to 10 μg L^?1 Cu(II) concentration range, the relative standard deviation is 0.4 % at a level of 0.1 μg L^?1 (for n?=?10), and the detection limit is as low as 73 ng L^?1. We consider this magnetic MOF composite to be a promising and highly efficient material for the preconcentration of metal ions.

Highly sensitive SERS probe for mercury(II) using cyclodextrin-protected silver nanoparticles functionalized with methimazole

We have developed a surface-enhanced Raman scattering (SERS) probe for the determination of mercury(II) using methimazole-functionalized and cyclodextrin-coated silver nanoparticles (AgNPs). These AgNPs in pH 10 solution containing sodium chloride exhibit strong SERS at 502 cm^?1. Its intensity strongly decreases in the presence of Hg(II). This effect serves as the basis for a new method for the rapid, fast and selective determination of trace Hg(II). The analytical range is from 0.50 μg L^?1 to 150 μg L^?1, and the limit of detection is 0.10 μg L^?1. The influence of 11 metal ions commonly encountered in environmental water samples was found to be quite small. The method was applied to the determination of Hg(II) in spiked water samples and gave recoveries ranging from 98.5 to 105.2 % and with relative standard deviations of <3.5 % (n?=?5). The total analysis time is <10 min for a single sample.

Solid phase extraction of Cd(II) and Pb(II) using a magnetic metal-organic framework, and their determination by FAAS

We describe a novel magnetic metal-organic framework (MOF) for the preconcentration of Cd(II) and Pb(II) ions. The MOF was prepared from the Fe₃O₄-pyridine conjugate and the copper(II) complex of trimesic acid. The MOF was characterized by IR spectroscopy, elemental analysis, SEM and XRD. A Box-Behnken design through response surface methodology and experimental design was used to identify the optimal parameters for preconcentration. Extraction time, amount of magnetic MOF and pH value were found to be critical factors for uptake, while type, volume, concentration of eluent, and elution time are critical in the elution step. The ions were then determined by FAAS. The limits of detection are 0.2 and 1.1 μg?L^?1 for Cd(II), and Pb(II) ions, respectively, relative standard deviations are <4.5% (for five replicates at 50 μg?L^?1 of Cd(II) and Pb(II) ions), and the enrichment capacity of the MOF is at around 190 mg?g^?1 for both ions which is higher than the conventional Fe3O4-pyridine material. The magnetic MOF was successfully applied to the rapid extraction of trace quantities of Cd(II) and Pb(II) ions in fish, sediment, and water samples.

Nanoparticles of type Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>-SiO<Subscript>2</Subscript>-graphene oxide and coated with an amino acid-derived ionic liquid for extraction of Al(III), Cr(III), Cu(II), Pb(II) prior to their determination by ICP-OES

An amino acid derived ionic liquid, Fe₃O₄ nanoparticles and graphene oxide (GO) were used to prepare a material for the magnetic solid phase extraction (MSPE) of the ions Al(III), Cr(III), Cu(II) and Pb(II). The material was characterized by Fourier transform infrared spectral (FT-IR), scanning electron microscopy (SEM), thermal gravimetric analysis (TGA), magnetic analysis and isoelectric point (pI) analysis. It is shown to be a viable sorbent for the separation of these metal ions. Single factor experiments were carried out to optimize adsorption including pH values, ionic strength, temperature and solution volume. Following desorption with 0.1 M HCl, the ions were quantified by inductively coupled plasma optical emission spectrometry. Under the optimum conditions, the method provides a linear range from 10 to 170 μg· L^?1 for Al(III); from 4.0 to 200 μg· L^?1 for Cr(III); from 5.0 to 170 μg· L^?1 for Cu(II); and from 5.0 to 200 μg· L^?1 for Pb(II). The limits of detection (LOD) are 6.2 ng L^?1 for Al(III); 1.6 ng L^?1 for Cr(III); 0.52 ng L^?1 for Cu(II); and 30 ng L^?1 for Pb(II). Method performance was investigated by determination of these ions in (spiked) environmental water and gave recoveries in the range of 89.1%–117.8%.

Open image in new window

Graphical abstract The graph shows that Al(III), Cr(III), Cu(II), Pb(II) are not adsorbed quantitatively by Fe₃O₄-SiO₂. On the other hand, Cr(III) and Pb(II) are adsorbed quantitatively by Fe₃O₄-SiO₂-GO while Al(III) and Cu(II) are not quantitatively retained. However, 3D–Fe₃O₄-SiO₂-GO-AAIL adsorb all these 4 metal ions quantitatively.

     

A metal-organic framework sustained by a nanosized Ag12 cuboctahedral node for solid-phase extraction of ultra traces of lead(II) ions

We show that a metal-organic framework (MOF) sustained by a nanosized Ag12 cuboctahedral node can be applied to selectively extract traces of lead(II) ion from environmental water samples. The MOF was characterized by thermogravimetric and differential thermal analysis, scanning electron microscopy, FTIR, and X-ray diffraction. The effects of pH value, flow rates, of type, concentration and volume of the eluent, of break-through volume and potentially interfering ions on the separation and determination of lead were evaluated. Following desorption with EDTA, Pb(II) was quantified by FAAS. The use of the MOF results in excellent analytical figures of merit including an analytical range from 2 to 180 μg L^?1 of Pb(II) (R²?>?0.99); a limit of detection of 500 ng L^?1; an adsorption capacity of 120 mg g^?1; an extraction efficiency of >95 %, and a relative standard deviation of <4 % (for eight separate column experiments).

Solid-phase preconcentration of cadmium(II) using amino-functionalized magnetic-core silica-shell nanoparticles, and its determination by hydride generation atomic fluorescence spectrometry

We report on the synthesis and evaluation of aminated-CoFe₂O₄/SiO₂ nanoparticles that can serve as a selective solid-phase sorbent for the extraction of cadmium ion. The nanoparticles consist of a magnetic CoFe₂O₄ core and an amino-modified silica shell. They can efficiently extract cadmium(II) ion and then can be isolated from the sample solution due to the magnetic nature of the core. The effects of the experimental conditions on the extraction process were optimized. Cadmium was then quantified by hydride generation atomic fluorescence spectrometry. The resulting calibration curve is linear in the concentration range of 0.01–10 μg?L^?1, the instrumental detection limits (3σ) is 3.15 ng?L^?1 and the relative standard deviation is 4.9 % at the 1.0 μg?L^?1 level (for n?=?11). The enrichment factor is 50 (for 50 mL samples), and the adsorbent can be used for at least 45 cycles of preconcentration and elution. The method was applied to the determination of cadmium in environmental water samples, and successfully validated by analyzing two certified reference materials.

Emulsification based dispersive liquid microextraction prior to flame atomic absorption spectrometry for the sensitive determination of Cd(II) in water samples

We report on the application of emulsification-based dispersive liquid microextraction (EB-DLME) to the preconcentration of Cd(II). This procedure not only possesses all the advantages of routine DLLME, but also results in a more stable cloudy state which is particularly useful when coupling it to FAAS. In EB-DLME, appropriate amounts of the extraction solvent (a solution of dithizone in chloroform) and an aqueous solution of sodium dodecyl sulfate (SDS; acting as a disperser) are injected into the samples. A stable cloudy microemulsion is formed and Cd(II) ion is extracted by chelation. After phase separation, the sedimented phase is subjected to FAAS. Under optimized conditions, the calibration curve for Cd(II) is linear in the range from 0.1 to 25 μg L^?1, the limit of detection (at S/N?=?3) is 30 pg L^?1, the relative standard deviations for seven replicate analyses (at 0.56 μg L^?1 of Cd(II)) is 4.6 %, and the enrichment factor is 151. EB-DLME in our opinion is a simple, efficient and rapid method for the preconcentration of Cd(II) (and most likely of many other ions) prior to FAAS determination.

Comparison of the performance of different modified graphene oxide nanosheets for the extraction of Pb(II) and Cd(II) from natural samples

Graphene nanosheets were modified with amino groups and the resulting material was used as a sorbent for the extraction of cadmium and lead ions. The nanosheets were characterized by IR spectroscopy, transmission electron microscopy, thermal gravimetric analysis and elemental analysis. The effects of sample pH, eluent parameters (type, concentration and volume of eluent), flow rates (of both sample and eluent), and of a variety of other ions on the efficiency of the extraction of Cd(II) and Pb(II) were optimized. Following solid phase extraction, the elements were determined by FAAS. The limits of detection are <0.9 μg L^?1 for Pb(II) and <5 ng L^?1 for Cd(II). The relative standard deviations are <2.2 %. The method was validated by analyzing several certified reference materials and was then used for Pb(II) and Cd(II) determination in natural waters and vegetables.

A nanosized cadmium(II)-imprinted polymer for use in selective trace determination of cadmium in complex matrices

We describe a nanosized Cd(II)-imprinted polymer that was prepared from 4-vinyl pyridine (the functional monomer), ethyleneglycol dimethacrylate (the cross-linker), 2,2′-azobisisobutyronitrile (the radical initiator), neocuproine (the ligand), and Cd(II) (the template ion) by precipitation polymerization in acetonitrile as the solvent. The imprinted polymer was characterized by X-ray diffraction, thermogravimetric analysis, differential thermal analysis, and scanning electron microscopy. The maximum adsorption capacity of the nanosized sorbent was calculated to be 64 mg g^?1. Cadmium(II) was then quantified by FAAS. The relative standard deviation and limit of detection are 4.2 % and 0.2 μg L^?1, respectively. The imprinted polymer displays improve selectivity for Cd(II) ions over a range of competing metal ions with the same charge and similar ionic radius. This nanosized sorbent is an efficient solid phase for selective extraction and preconcentration of Cd(II) in complex matrices. The method was successfully applied to the trace determination of Cd(II) in food and water samples.

Magnetic titanium oxide nanoparticles for hemimicelle extraction and HPLC determination of organophosphorus pesticides in environmental water

We report on a method for the extraction of organophosphorus pesticides (OPPs) from water samples using mixed hemimicelles and magnetic titanium dioxide nanoparticles (Fe₃O₄@TiO₂) modified by cetyltrimethylammonium. Fe₃O₄@TiO₂ nanoparticles were synthesized by a hydrothermal process and then characterized by scanning electron microscopy and Fourier transform IR spectrometry. The effects of the quantity of surfactant, extraction time, desorption solvent, pH value, extraction volume and reuse of the sorbent were optimized with respect to the extraction of OPPs including chlorpyrifos, dimethoate, and trichlorfon. The extraction method was applied to analyze OPPs in environmental water using HPLC along with UV detection. The method has a wide linear range (100–15,000 ng L^?1), good linearity (r?>?0.999), and low detection limits (26–30 ng L^?1). The enrichment factor is ~1,000. The recoveries (at spiked levels of 100, 1,000 and 10,000 ng L^?1) are in the range of 88.5–96.7 %, and the relative standard deviations range from 2.4 % to 8.7 %.

Chemically modified alumina nanoparticles for selective solid phase extraction and preconcentration of trace amounts of Cd(II)

We have developed a solid phase extraction method for the determination of cadmium ions in aqueous samples. It is based on the adsorption of Cd(II) on alumina nanoparticles coated with sodium dodecyl sulfate and modified with a newly synthesized Schiff base. Analytical parameters such as pH value, amount of adsorbent, type and concentration of eluent, flow rates of the sample and eluent, sample volume and matrix effects were optimized. Desorption is accomplished with 2?mol?L^?1 nitric acid. Cd(II) was then determined by flame atomic absorption spectrometry. The maximum enrichment factor is 75. Under the optimum experimental conditions, the detection limit is 0.14???g?L^?1 in original solution. The adsorption capacity of the modified sorbent is 4.90?mg?g^?1 for cadmium ions. The method was applied to the determination of trace quantities of Cd(II) in water, wastewater, and biological and food samples with satisfactory results.

A magnetic copper(II)-imprinted polymer for the selective enrichment of trace copper(II) ions in environmental water

We have developed a convenient, selective and reliable method for the rapid enrichment of trace quantities of Cu(II) by using a magnetic Cu(II) ion-imprinted polymer. This is followed by their determination by FAAS. The imprints were prepared by using (a) Cu(II) ions as the template, (b) 3-aminopropyltriethoxysilane as both the functional monomer and the crosslinking agent, and (c) Fe₃O₄ as the magnetic component. Enrichment is carried out in a single step, and adsorbed copper ions can be separated from the sample solution by applying a strong magnet. The effects of pH, elution condition, amount of imprint, and of potentially interfering ions were evaluated. Under the optimal conditions, the detection limit and enrichment factor are 0.3?μg L^?1 and 100, respectively, and the recovery is >95?%. The procedure was successfully applied in the enrichment and detection of trace copper ions in environmental water.

Determination of chlorobenzenes in water samples based on fully automated microextraction by packed sorbent coupled with programmed temperature vaporization–gas chromatography–mass spectrometry

A fully automated method consisting of microextraction by packed sorbent (MEPS) coupled directly to programmed temperature vaporizer–gas chromatography–mass spectrometry (PTV–GC–MS) has been developed to determine the 12 chlorobenzene congeners (chlorobenzene; 1,2-, 1,3-, and 1,4-dichlorobenzene; 1,2,3-, 1,2,4-, and 1,3,5-trichlorobenzene; 1,2,3,4-, 1,2,3,5-, and 1,2,4,5-tetrachlorobenzene; pentachlorobenzene; and hexachlorobenzene) in water samples. The effects of the variables on MEPS extraction, using a C18 sorbent, and the instrumental PTV conditions were studied. The internal standard 1,4-dichlorobenzene d4 was used as a surrogate. The proposed method afforded good reproducibility, with relative standard deviations (RSD %) lower than 12 %. The limits of detection varied between 0.0003 μg L^?1 for 1,2,3,4-tetrachlorobenzene and 0.07 μg L^?1 for 1,3- and 1,4-dichlorobenzene, while those of quantification varied between 0.001 μg L^?1 and 0.2 μg L^?1 for the same compounds. Accuracy of the proposed method was confirmed by applying it to the determination of chlorobenzenes in different spiked water samples, including river, reservoir, and effluent wastewater.

Preconcentration of trace cadmium ion using magnetic graphene nanoparticles as an efficient adsorbent

Graphene-based magnetic nanoparticles (G-Fe₃O₄) were prepared and used as an effective adsorbent for the solid-phase extraction of trace quantities of cadmium from water and vegetable samples. The method avoids some of the time-consuming steps associated with traditional solid phase extraction. The excellent sorption property of the G-Fe₃O₄ system is attributed to π - π stacking interaction and hydrophobic interactions between graphene and the Cd-PAN complex. The effects of pH, the amount of G–Fe₃O₄, extraction time, type and volume of eluent, desorption time and interfering ions on the extraction efficiency were optimized. The preconcentration factor is 200. Cd(II) was then quantified by flame atomic absorption spectrometry with a detection limit of 0.32 ng mL^?1. The relative standard deviation (at 50 ng mL^?1; for n?=?10) is 2.45 %. The method has a linear analytical range from 1.1 to 150 ng mL^?1, and the recoveries in case of real samples are in the range between 93.1 % and 102.3 %.

Preconcentration and separation of ultra-trace palladium ion using pyridine-functionalized magnetic nanoparticles

We present a study on the application of magnetic nanoparticles (MNPs) prepared from Fe₃O₄ and functionalized with pyridine as an adsorbent for the solid-phase extraction of trace quantities of Pd(II) ion. The pyridine group was immobilized on the surface of the MNPs by covalent bonding of isonicotinamide. The modified MNPs can be readily separated from an aqueous solution by applying an external magnetic field. Effects of pH, the amount of functionalized MNPs, extraction time, type and quantity of eluent, desorption time, break-through volume and interfering ions on the extraction efficiency were optimized. The amount of Pd(II) was then determined using FAAS. Under the optimized conditions, the detection limit and preconcentration factor are 0.15?μg?L^-1 and 196, respectively, and the relative standard deviation (at 20?μgL^?1; for n?=?10) is 3.7?%. The method had a linear analytical range from 1 to 80?μg?L^-1 and was applied to determine Pd(II) in spiked tape water and soil.

Preconcentration and in-situ photoreduction of trace selenium using TiO2 nanoparticles, followed by its determination by slurry photochemical vapor generation atomic fluorescence spectrometry

We have developed a method for the determination of trace levels of total selenium in water samples. It integrates preconcentration, in-situ photoreduction and slurry photochemical vapor generation using TiO₂ nanoparticles, and the determination of total selenium by AFS. The Se(IV) and Se(VI) species were adsorbed on a slurry of TiO₂ nanoparticles which then were exposed to UV irradiation in the presence of formic acid to form volatile selenium species. The detection limits were improved 17-fold compared to hydride generation and 56-fold compared to photochemical vapor generation, both without any preconcentration. No significant difference was found in the limits of detection (LODs) for Se(IV) and Se(VI). The LOD is as low as 0.8 ng L^?1, the precision is better than 4.5 % (at a level of 0.1 μg L^?1 of selenium). The method gave good recoveries when applied to the determination of total selenium in a certified tissue reference material (DORM-3) and in spiked drinking water and wastewater samples containing high concentrations of transition and noble metal ions. It also excels by very low LODs, a significant enhancement of sample throughput, reduced reagent consumption and sample loss, and minimal interference by transition and noble metal ions.

A metal-organic framework nanocomposite made from functionalized magnetite nanoparticles and HKUST-1 (MOF-199) for preconcentration of Cd(II), Pb(II), and Ni(II)

The author describes the preparation of a magnetic metal organic framework of type MOF-199 containing magnetite (Fe₃O₄) nanoparticles carrying covalently immobilized 4-(thiazolylazo) resorcinol (Fe₃O₄@TAR). This material is shown to represent a viable sorbent for separation and preconcentration of Cd(II), Pb(II), and Ni(II) ions. Box-Behnken design was applied to optimize the parameters affecting preconcentration. Following elution with 0.6 mol L^?1 EDTA, the ions were quantified by FAAS. The capacity of the sorbent ranged between 185 and 210 mg g^?1. The limits of detection are 0.15, 0.40, and 0.8 ng mL^?1 for Cd(II), Ni(II), and Pb(II) ions, respectively. The relative standard deviations are <8.5 %. The method was successfully applied to the rapid extraction of trace amounts of these ions from sea food and agri food.

Open image in new window

Graphical abstract (a) A schematic diagram of Fe₃O₄ functionalization by TAR (4-(thiazolylazo) resorcinol). (b) The schematic illustration of the magnetic metal organic framework-TAR nanocomposite. H₃BTC: benzene-1,3,5-tricarboxylic acid; TEA: triethylamine; 3-CPS: 3-chloropropyl triethoxysilane.

     

Selective solid-phase extraction of trace mercury(II) using a silica gel modified with diethylenetriamine and thiourea

We describe a solid phase extractor for selective separation and preconcentration of Hg(II) ion. It was prepared by immobilizing the adduct of diethylenetriamine and thiourea on silica gel. The effects of solution acidity, preconcentration time, sample flow rate and volume were optimized. The results show that Hg(II) can be selectively extracted from acidic solutions and in presence of common other metal ions. The adsorbent is stable, can be reused more than 10 times, and the maximum adsorption capacity is 23 mg g^?1. Hg(II) was quantified by inductively coupled plasma optical emission spectrometry. The method has a detection limit of 23 ng L^?1, and the relative standard deviation is <2 %. The procedure was validated by analyzing two standard materials (river sediment and hair powder), and was successfully applied to the preconcentration of Hg(II) in real samples.

Cetyltrimethylammonium-coated magnetic nanoparticles for the extraction of bromate,followed by its spectrophotometric determination

We report on a combination of magnetic solid-phase extraction and spectrophotometric determination of bromate. Cetyltrimethylammonium ion was adsorbed on the surface of phenyl-functionalized silica-coated Fe₃O₄ nanoparticles (Ph-SiO₂@Fe₃O₄), and these materials served as the sorbent. The effects of surfactant and amount of sorbent, the composition of the desorption solution, the extraction time and temperature were optimized. Under optimized conditions, an enrichment factor of 12 was achieved, and the relative standard deviation is 2.9 % (for n?=?5). The calibration plot covers the 1–50 ng mL^?1 range with reasonable linearity (r ²?>?0.998); and the limit of detection is 0.5 ng mL^?1. The method is not interfered by ionic compounds commonly found in environmental water samples. It was successfully applied to the determination of bromate in spiked water samples.

Ultra-sensitive spectrophotometric determination of nickel after complexation and membrane filtration

We report on a simple, sensitive and selective method for the spectrophotometric determination of Ni²⁺ in water samples. The analyte ions were collected on a membrane filter in the form of their red complex with 1-(2-pyridylazo)-2-naphthol (PAN), and the absorption spectra of the colored membrane filters were acquired. Effects of pH value, sample volume, and amount of PAN were examined in order to optimize sensitivity. The interference by common other ions was eliminated using appropriate masking agents. The absorbance is linearly related to the concentration of Ni²⁺ in the ranges from 0.3 to 1.5 μg L^?1, and from 2 to 10 μg L^?1, respectively, the correlation coefficients (R²) being 0.9871 and 0.9954. Under the optimal conditions, the detection limit is 0.1 μg L^?1. The recoveries in case of spiked samples are between 95.0% and 101.5%, and the relative standard deviations range from 2.8% to 4.1%.