数字全息显微像平面相位畸变的自动补偿研究

对离轴数字全息显微相位畸变的自动补偿进行了理论和实验研究。首先对由CCD记录的数字全息图采用平均梯度自聚焦方法确定最佳再现距离,然后将修正的虚拟参考光作用于切趾滤波后的全息图进行数字再现,经像平面相位自动补偿后得到无畸变的物体相位分布。该方法仅需记录一幅离轴数字全息图就可以自动快速地重建物体的真实相位信息。     

大尺寸物光波面彩色数字全息高质量重建研究

为解决检测面尺寸较大时CCD难以得到高质量数字全息图的问题,本文利用负透镜设计光学系统让CCD接收来自物体的缩小虚像,以球面波为参考波,使用单色CCD近距离得到三种色光照射下的大尺寸彩色物体的数字全息图,然后采用可控放大率波面重建算法得到同一尺寸的数字全息重建像,合成彩色数字全息重建像.同时,使用两种消零级方法去除零级干扰,提高重建像质量,一种方法利用空间光调制器相移技术在参考光中加入一次任意相移,记录两幅数字全息图,消除重建零级像|另一种方法使用“无干扰全息图”消除重建零级像及共轭像.本文讨论结果可为大物体彩色数字全息及多波长数字全息检测应用提供有益的参考.     

彩色全息图的计算机产生和数字再现

提出了一种基于色彩合成以及菲涅尔衍射原理,用计算机产生全息图并用数字方法再现彩色全息图的方法。该方法的第一步是将物体的彩色RGB图像分离为三基色强度图,再利用博奇编码的方法制成修正离轴参考光分色计算机全息图;第二步是分别对分色全息图在频域进行调制以实现用原参考光真实再现原始物光波。通过滤波消除零级衍射及共轭像的影响,获得了所需要的实像并提高了像质。提供的实验是选用一幅RGB图像作为原始物体,给出了用博奇编码法制成的全息图以及最后经色彩合成获得的再现像。结果表明,该方法能使各分色全息图的再现像准确重合,解决了在色彩合成时容易出现的色串扰问题。     

Tukey窗函数用于数字全息图的切趾研究

提出采用Tukey窗函数对数字全息图进行切趾处理的方法,以削弱数字全息像再现过程中的孔径衍射效应,抑制再现波前的起伏.模拟实验结果表明,该方法显著改善了再现像中央区域的强度和相位分布,适用于微小物体的显微测量及微小形变测量等领域.     

大尺寸物体彩色全息图制作的研究

通过分析两步法制彩色全息图中全息图空间带宽积与物体大小、全息图记录距离的关系,提出了一种拍摄大尺寸物体彩色全息图的方法。经编码,设置参数,在视窗处平面记录下三分色全息图, 以保证用最小的幅面记录下物体的完整信息,并且H1rgb处于同一平面经原参考光的共轭光再现时,他们的再现像能完全重合;将H1rgb再现,获得大视场的物光波信息,三基色物波信息重合后,用光学方法记录大幅面的彩色全息。该方法能提高全息图再现像的视场和解决大尺寸物体的全息图难拍摄问题。 经实验验证,该方法能将全息图再现像的视场提高6倍左右。     

基于双色光照明的单曝光同轴数字全息技术

提出了一种基于双色光照明的单曝光同轴数字全息技术。在红绿蓝三色中,任选两种波长的光来照射物体,采用彩色CCD记录双色同轴全息图,然后经过三基色分离数字处理,可得到两幅不同波长的同轴全息图。用角谱衍射理论对该技术进行了分析,表明在降低物参光振幅比的条件下,通过对同轴数字全息图求自然对数,可近似得到衍射物光及其共轭之和,其误差与物参光振幅比有关。取两幅不同波长的同轴数字全息图,经自然对数处理后,用传递函数可以很好地重构出物体图像,给出了具体的数字处理算法。用仿真实验,模拟了该技术的全息记录和处理过程,得到重构图像的峰值信噪比(PSNR)为14.2 dB。结果表明该方法可以去除孪生衍射像干扰,可以实现清晰的单曝光同轴全息成像。最后,分析了再现像中噪声产生的原因。该技术可用于基于同轴全息的实时成像与动态测量。     

基于频域方法的三维物体分层重现

基于频域方法实现了数字记录和再现三维物体离轴全息图.通过频谱对应关系求得各个面的频谱分布,使用数字滤波方法,成功地消除了零级衍射和共轭像;通过改变再现距离,分别获取了三维物体各个截面的再现像.     

基于基元全息图空间频谱分析的计算全息参考光角度选择方法

提出了一种基于基元全息图频谱分析的计算全息参考光角度选择方法.通过分析基元全息图的空间频谱成分,导出全息图正确再现需要满足的约束条件;求解了基于空间光调制器的计算全息再现系统的参考光角度取值范围;用N-LUT算法计算了成像距离为1 000mm时,一幅22.5mm×26.1mm的二维图像取不同参考光角度时的全息图,并进行了数字再现和光学再现实验.结果表明:参考光角度在0.893 8°到1.398 0°之间选择可以获得质量良好的再现像;参考光角度小于0.893 8°时,再现像与共轭像不能完全分离,参考光角度大于1.398 0°时,全息图频率过高会造成欠采样,导致再现像与下一级共轭像互相交叠.实验现象与理论分析一致,验证了参考光夹角选择方法的正确性.     

相移同轴无透镜傅里叶数字全息的分析与实验

应用菲涅耳衍射和全息理论，详细分析了无透镜傅里叶变换数字全息图的记录、再现方法和再现像的特点，分析了相移数字全息图的记录和再现方法，并进行了相应的实验验证。结果表明：直接对无透镜傅里叶数字全息图进行傅里叶逆变换可同时得到与物体完全相同的再现像及其共轭像；同轴无透镜傅里叶数字全息术能最大程度满足CCD对采样条件的要求，从而可以增大记录物体的尺寸，减小记录距离，明显提高再现像的清晰度和分辨率；相移数字全息术能有效地消除数字再现光场中的零级光场和共轭像，显著提高再现像的信噪比。条件许可时，相移同轴无透镜傅里叶数字全息术是目前解决数字全息术中再现像的分离与满足采样条件之间矛盾的最佳方法。     

预放大数字全息显微系统的特点

为了提高预放大数字全息显微系统的成像质量,采用理论分析与实验验证相结合的方法,分别对采用平面及球面参考光记录的预放大数字全息显微系统进行了研究和比较。结果表明:在通常的实验条件下,系统的横向分辨力主要取决于显微物镜的成像分辨力;记录距离较小时,两种系统的横向分辨力均随着记录距离的增大略有降低;但当记录距离较大时,球面参考光预放大数字全息系统的横向分辨力降低得更为明显,即平面参考光预放大数字全息显微系统较为优越;在记录距离为0的情况下,即像面数字全息成像情况下,两种系统的再现像均具有最高的分辨力,在利用普通工业用传感器条件下,横向分辨力远超过了2.19 m,且像质较好。因此,尽可能减小全息图的记录距离,或者采用像面数字全息系统,可以有效提高数字全息系统的成像分辨力。     

Controlling image size as a function of distance and wavelength in Fresnel-transform reconstruction of digital holograms

A method for controlling the size of amplitude and phase images reconstructed from digital holograms by the Fresnel-transform method is proposed and demonstrated. The method can provide a constant reconstruction pixel width in the reconstructed image plane, independent of the recording and reconstruction distance. The proposed method makes it possible to maintain the size of an object for a sequence of digital holograms recorded at different distances and, therefore, to subtract phase maps for an object recorded at different distances. Furthermore, the method solves the problem of superimposition in multiwavelength digital holography for color display and holographic interferometry applications.     

利用综合复用技术拓展数字全息显微系统中的记录视场

为了解决现有数字全息显微系统中高分辨率与大记录视场无法同时兼得的问题, 提出了一种在不牺牲分辨率的前提下拓展数字全息显微记录视场的方法. 该方法中运用了波长不同、偏振态不同的四路相互不相干的探测物光, 同时探测被测样品四个相邻的不同区域, 并使这四束探测物光分别与其相应的参考光相干, 在记录面上同时记录下含有被测样品不同区域信息的复合全息图. 将获得的复合全息图经过频谱变换和数字滤波, 分别重构出所记录区域的振幅和相位分布.最后通过图像拼接和图像融合技术, 可实现接近原记录视场四倍的大视场数字全息显微记录. 该方法在测量过程中无需移动记录装置、光源和被测样品, 单次曝光即可实现, 实验结果验证了本文所提方法的可行性. 关键词： 数字全息显微术 角分复用 偏振复用 波长复用     

像面滤波技术在无透镜傅里叶变换数字全息中的应用

无透镜傅里叶变换数字全息波前重建主要采用全息图的一次快速傅里叶变换方法,重建图像不能充分占有重建平面.本文基于像平面滤波技术,提出对物体局部区域光波场进行放大重建并让重建图像布满重建平面的方法,给出具有精细结构物体的数字全息波前重建实例.此外,将数字全息光波场重建视为具有方形出射光瞳的光学系统的相干光成像过程,导出了物体放大图像的分辨率与光学系统相关参量的关系,并通过实验给予证明.     

像面滤波技术在无透镜傅里叶变换数字全息中的应用

无透镜傅里叶变换数字全息波前重建主要采用全息图的一次快速傅里叶变换方法,重建图像不能充分占有重建平面.本文基于像平面滤波技术,提出对物体局部区域光波场进行放大重建并让重建图像布满重建平面的方法,给出具有精细结构物体的数字全息波前重建实例.此外,将数字全息光波场重建视为具有方形出射光瞳的光学系统的相干光成像过程,导出了物体放大图像的分辨率与光学系统相关参量的关系,并通过实验给予证明.     

Autofocusing of digital holographic microscopy based on off-axis illuminations

An auto-focusing method for digital holographic microscopy has been proposed by employing two off-axis illumination beams. When specimens are illuminated by two plane waves in different directions, it is found that the farther the reconstruction plane is from the image plane, the wider the two reconstructed images are separated from each other. Thus, the image plane can be determinated by finding the minimum of the variation between the two reconstructed object waves on both the amplitude and phase distributions. The feasibility of the proposed method is demonstrated by the corresponding simulation and experiment.     

Joint approach of the sub-holograms in on-axis lensless Fourier phase-shifting synthetic aperture digital holography

In on-axis lensless Fourier phase-shifting synthetic aperture digital holography, to compose all of the phase-shifting sub-holograms to a large synthetic aperture digital hologram effectively, firstly, the cross-correlation algorithm of the object waves is presented to correct the joint misplacement of the sub-holograms. Secondly, to make the phase-shifting synchronization matching of different sequence phase-shifting holograms, the cross-correlation algorithm of the phase-shifting holograms is employed. Compared with the traditional cross-correlation algorithm of the sub-holograms, the proposed approach makes the joint precision of the sub-holograms reach sub-pixel accuracy, and the resolution of the reconstructed image is improved significantly. In general, the proposed approach is effective in restraining the quality degradation of the synthetic reconstructed image that comes from the joint misplacement of the sub-holograms and the phase-shifting non-synchronization of the phase-shifting holograms.     

Study on the reduction of speckle noise in the reconstructed image of digital hologram

As one of the most important 3-D display technique, reduction of speckle noise in the reconstructed image of digital holography should be grounded on the digital hologram itself. Based on the whole process of the recording and reconstruction of digital holography, the optical distributions of recorded object and reconstructed image of digital holography have been studied. It has been proposed that the root formation cause of speckle noise in its reconstructed image is the speckle noise formed on the recorded object surface when illuminated by coherent light because of its optical roughness. A novel approach has been presented to reduce speckle noise in digital holography by changing the interference structure of hologram itself. First, by reducing the speckle noise in the reconstructed image, the distribution of ideal reconstruction light with reduced speckle noise is acquired. Then in turn, taking the ideal reconstruction light with reduced speckle noise as ideal object light, a new hologram can be rebuilt, which can reconstruct the ideal object light. The experimental results are given to confirm the proposed method. Therefore, it offers a brand-new thought and practical way to reduce the speckle noise in the reconstructed image of digital holography.     

数字全息显微系统结构参量对再现像质的影响

为了获取高质量的数字全息显微再现像,分析了同轴相移数字全息显微系统结构参量对再现像质的影响.首先经过计算得出理想成像时,像空间物光波频率完全由物体面形结构频率和系统放大倍率决定.然后基于显微成像时物光波的所有频率分量都应该被有效记录的分析,得出在同轴相移系统中放大倍率必须使物光波的空间频率缩小到满足采样要求|并得出在相同的放大倍率下记录距离会影响有效记录的物体尺寸,记录器件离开像平面的距离越小,有效记录的物体尺寸越大,在像平面上时有效记录的物体尺寸最大.计算机仿真和光学实验都证明了上述结论的正确性.     

Digital holographic image fusion for a larger size object using compressive sensing

Digital holographic imaging fusion for a larger size object using compressive sensing is proposed. In this method, the high frequency component of the digital hologram under discrete wavelet transform is represented sparsely by using compressive sensing so that the data redundancy of digital holographic recording can be resolved validly, the low frequency component is retained totally to ensure the image quality, and multiple reconstructed images with different clear parts corresponding to a laser spot size are fused to realize the high quality reconstructed image of a larger size object. In addition, a filter combing high-pass and low-pass filters is designed to remove the zero-order term from a digital hologram effectively. The digital holographic experimental setup based on off-axis Fresnel digital holography was constructed. The feasible and comparative experiments were carried out. The fused image was evaluated by using the Tamura texture features. The experimental results demonstrated that the proposed method can improve the processing efficiency and visual characteristics of the fused image and enlarge the size of the measured object effectively.