耐高温聚氨酯弹性体

简述了聚氨酯的结构以及与其它材料复合对改善聚氨酯弹性体耐热形变性能的影响.结构上从形成硬段和软段的原料出发,引入刚性结构,分别提高硬段和软段的耐温性,从而加强材料耐温性.聚氨酯分别与无机材料复合和有机材料复合,以及形成互穿网络结构,都可以提高聚氨酯复合材料的耐高温性能.     

Novel Polyurethane Gels: The Effect of Structure on Gelation

Novel polyurethane gels have been reported in common solvent like dimethyl formamide (DMF). Polyurethanes have been synthesized from diisocyanates, diols and rigid chain extenders. We have illustrated the influence of chemical structure of the chain extenders on gelation rate, thermal property and morphology of the gels in DMF. Gelation rate increases significantly with the rigidity of the chain extender. Introduction of more rigid chain extender molecules in polyurethane prepolymer enhanced the thermal stability of the pure polymer. On the contrary, the solvent retention power of the gels gradually decreases with increasing rigidity of chain extender presumably because of the poor dispersion/greater aggregation of the hard segments in the soft segment matrix. Morphology and formation of gelation have been discussed.     

Thermal properties of poly(urethane-ester-siloxane)s based on hyperbranched polyester

Novel polyurethanes (PUs) were synthesized using hydroxy-terminated hyperbranched polyester (BH-20) and 4,4′-methylenediphenyl diisocyanate (MDI) as hard segments and hydroxy-terminated ethylene oxide-poly(dimethylsiloxane)-ethylene oxide triblock copolymer (PDMS-EO) as soft segment, with soft segment content ranging from 30 to 60 wt %. The PUs were synthesized by two-step solution polymerization method. The influence of the soft segment content on the structure, swelling behavior and thermal properties of PUs was investigated. According to the results obtained by swelling measurements, the increase of the hard segment content resulted in the increase of the crosslinking density of synthesized samples. DSC results showed that the glass transition temperatures increase from 36 to 65°C with increasing hard segment content. It was demonstrated using thermogravimetric analysis (TGA) that thermal stability of investigated PUs increases with increase of the soft PDMS-EO content. This was concluded from the temperatures corresponding to the 10 wt % loss, which represents the beginning of thermal degradation of samples.     

Synthesis, characterization and properties of a novel fluorinated polyurethane

A novel fluorinated polyurethane (FPU) was prepared by fluorinated polyether glycol (PTMG-g-HFP) as a soft segment, 1,6-hexamethylene diisocyanate (HDI) or toluene diisocyanate (TDI) as a hard segment and 1,4-butanodiol (BDO) as a chain extender. Fourier transform infrared spectroscopy (FTIR), ¹H NMR, ¹³C NMR and gel permeation chromatography (GPC) were used to characterize the structure of the fluorinated polyurethane. The thermal stabilities of the fluorinated polyurethane and the corresponding hydrogenated polyurethane were studied by thermogravimetric analysis (TGA). X-ray photoelectron spectroscopy (XPS) analysis at two different sampling depths for the fluorinated polyurethane was used to investigate the surface compositions of FPU. And the mechanical properties of the fluorinated polyurethane and the corresponding hydrogenated polyurethane were also measured. Chemical resistance of polyurethane films was estimated through spot tests with different solvents. The results showed that FPU had high thermal stability, strain-hardening property and good chemical resistance. The XPS measurements showed the fluorine enrichment on the surface of FPU.     

不同软段结构聚氨酯-酰亚胺嵌段共聚物的合成及热性能研究

用二步法合成了不同软段 (PPO ,PEG ,PEPA)聚氨酯 酰亚胺 (PUI)嵌段共聚物 ,FTIR光谱表征了所有合成PUI分子主链均含有酰亚胺链段 ,并研究了PUI嵌段共聚物的热性能受软段类型及长度的影响 .DSC研究表明聚酯型PUI的软硬段之间的相容性比聚醚型PUI好 ,随相同软段分子量的增加 ,PUI体系的软硬段兼容性变差 ,并显示了相分离的特征 ;热失重 (TGA)研究得出不同软段的PUI样品的热稳定性大小顺序为 :PEPA PUI >PEG PUI>PPO PUI ;动态力学 (DMTA)研究给出了所合成的PUI样品在 5 0～ 2 0 0℃范围内均出现了较长的模量平台显示出有较好的耐热性 ,且随硬段含量的升高其储能模量不断增强     

TGA/FTIR studies of segmented aliphatic polyurethanes and their nanocomposites prepared with commercial montmorillonites

Nanocomposites prepared with segmented polyurethane (SPU) and commercially available nanoclays (Cloisite™ Na⁺, Cloisite™ 15A, Cloisite™ 30B) were studied using thermogravimetric analysis coupled with Fourier Transform Infrared Spectroscopy (TGA/FTIR). The results showed that the thermal degradation of unfilled SPU and the 4, 6 and 10 wt% hand mixed nanocomposites occurred in two stages being the first due to degradation of hard segments and the second due to the degradation of soft segments. It was also found that the thermal stability of these nanocomposites was not improved by increasing nanoclay concentration except for SPU/Cloisite™ 15A nanocomposites were a 40 °C increase was observed. In a similar manner, FTIR spectra of the evolved gases obtained after the thermal degradation of these nanocomposites were qualitatively similar to the unfilled polymer except in those containing Cloisite™ 30B where isocyanate absorptions were detected. In contrast, SPU/Cloisite™ 30B nanocomposites prepared by in-situ polymerization, exhibited higher thermal stability than the corresponding hand mixed nanocomposites. In addition, these nanocomposites exhibited the presence of carbon dioxide in the evolved gases during its second degradation stage which was not observed in the hand mixed nanocomposites. In this case, it can be said that the presence of clays in the nanocomposites has a significant effect on the thermal degradation pathways.     

Synthesis and characterization of novel environmentally friendly shape memory polyurethanes based on poly(epsilon-caprolactone) diol/castor oil mixtures

A new category of polyurethane plastics (PUs) was obtained from poly (ε-caprolactone) diol/castor oil mixture as a dual-component of their soft segment and hexamethylene diisocyanate (HDI) as the hard segment. The main aim of this study was to explore the effect of castor oil on content chemical structure, dynamic and mechanical properties and low temperature heat induced shape memory of the obtained polyurethane system. The chemical structure of samples was confirmed by Fourier transforms infrared (FTIR) and nuclear magnetic resonance (NMR) spectroscopy. Differential scanning calorimetry (DSC) was carried out to study thermal transitions of synthesized polyurethanes. At 50 mol % of oil, the polyurethane showed the highest enhancement in tensile strength (54%) and Young’s modulus (23%) compared to PU-0. The PU containing 50 mol % of oil was nearly recovered by 99%.     

软段含离子的含氟水性聚氨酯的制备

以单羟基氟碳链一元醇为有机氟改性剂,将含氟基团引入聚氨酯主链中,通过分子设计的方法制备出软段含有离子基团的有机氟阴离子型水性聚氨酯。 比较了传统水性聚氨酯、硬段含氟的水性聚氨酯和软段含氟的水性聚氨酯在合成方法、耐水性、 热稳定性以及结晶性方面的差异;实验证明了软段含氟聚氨酯的水性聚氨酯的性能最为优良。 通过红外光谱的表征确定了氟化聚氨酯的结构,并证明了含氟基团的引入对聚氨酯软硬段间氢键作用的影响;水接触角由73°增加至107°,吸水溶胀率降低了66%,胶膜耐水性提高;热重分析结果表明,含氟聚氨酯的最大热失重温度提高了30 ℃,热稳定性增加;广角X射线衍射结果表明,胶膜的结晶度增加,结晶形式发生了微小程度的转变;扫描电子显微镜结果证明存在不均匀的多相结构。     

Theoretical modeling of the relationship between Young's modulus and formulation variables for segmented polyurethanes

We describe a new modeling approach to prediction of Young's modulus of segmented polyurethanes. This approach combines micromechanical models with thermodynamic considerations based on the theory of block copolymers. The resulting model predicts both the equilibrium morphology and the “ideal” Young's modulus of a segmented polyurethane polymer as a function of its formulation (hard segment chemical structure, hard segment weight fraction, soft segment equivalent weight) and temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2123–2135, 2007     

Exploring preferential association of laponite and cloisite with soft and hard segments in TPU‐clay nanocomposite prepared by solution mixing technique

Thermoplastic polyurethane (TPU) is a versatile polymer exhibiting many engineering applications. In this article, two varieties of clay (Cloisite and Laponite RD) have been used to prepare TPU‐based nanocomposites. They differ in, chemical composition, hydrophobicity, aggregation tendency, and dispersibility in a particular solvent. A detailed investigation of the thermal, morphological, and rheological behavior reflects the affinity of Cloisite towards the soft segment, whereas it is the hard segment for modified Laponite. The maximum improvement in onset degradation temperature has been observed to be 17.5 and 8.3 °C for Cloisite and Laponite, respectively. Five percent Cloisite‐filled sample shows optimum storage modulus in the glassy region where as it is the 10% filled sample at the rubbery region. However, the trend remains indifferent both in rubbery and glassy regions for Laponite, and properties have been found optimum for 3% filled sample. To explore the behavior in the terminal and flow regions, dynamic rheological experiments were performed in low shear rate. Variation in dynamic rheological properties can be explained well on the basis of the combination of partly exfoliated, intercalated, and aggregated structures of the nano clay inside the TPU matrix, depending on their nature and preferential association with different segments. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 2341–2354, 2008     

Control of hard segment size in polyurethane formation

In general, segmented polyurethane elastomers are prepared by reacting an isocyanate-capped polyol prepolymer with a short-chain diol chain extender, yielding an elastomer with hard segments of uniform size. However, the hard segment size will not be uniform if the polyurethane polymer is prepared by forming the hard segment first, followed by soft segment formation. Because the mechanical properties of polyurethane elastomers depend on the relative ratio of the hard to soft segments as well as the effectiveness of the hard segment as a physical crosslinker, the control of the size distribution of the hard segment is a key factor in designing polyurethane elastomers. It was found that reaction conditions can affect the size distribution of hard segments derived from an aliphatic diisocyanate with differential reactivity between the two isocyanate groups. Lower reaction temperatures and simultaneous mixing of all reactants gave the preferred size distribution of hard segments. © 1995 John Wiley & Sons, Inc.     

聚乙二醇型聚氨酯软硬段对其相变储热性能的影响

以不同分子量的聚乙二醇(PEG)为软段,MDI-BDO为硬段,采用两步法溶液聚合合成一种具有固-固相变储热性能的聚氨酯材料.通过DSC,WAXD等测试手段对体系的软硬段结晶性,微相分离,相变可逆性及循环热稳定性进行研究,结果表明,聚氨酯中硬段的存在对软段结晶有着很大的影响,当软段分子量达到2000或以上时,软段才具有较大的结晶度和熔融相变焓,且硬段含量必须高于一定值才能形成较为完善的物理交联网络以保证材料在发生相变时维持固体状态.同时符合这两个条件的试样能具有较好的固-固相变储热性能.就软段PEG含量及分子量对材料储热性能的影响进行了研究,通过调节软段含量与分子量得到一系列具有不同相变焓和相变温度的聚氨酯固-固相变储热材料.经测试还发现,该材料具备很好的相变可逆性和循环热稳定性,是一类很有开发前景的相变储热材料.     

Synthesis and properties of sulfonated polyurethane ionomers with anions in the polyether soft segments

A series of polyether (PTMO, PEO) polyurethane ionomers having different contents of sodium sulfonate groups in the soft segments have been synthesized. The reaction of transesterification was involved in the incorporation of the sodium sulfonate groups in the polyether. The polyurethane ionomers were characterized by means of dynamic mechanical thermal analysis, differential scanning calorimetry, and small-angle x-ray scattering. Solid-state ionic conductivity was also measured. As the ionization level increased, the compatibility of the hard and soft segments increased and the glass transition region of the soft segment became broader. These samples had relatively higher moduli and good film-forming ability. Moreover, this kind of ionomer provides a very promising ionic conductive multiphase polymer with a single ion transport mechanism. © 1997 John Wiley & Sons, Inc.     

Influence of varying hard segments on the properties of chemically crosslinked moisture‐cured polyurethane‐urea

Polyurethane prepolymers are widely used in the reactive hot melt adhesives and moisture‐cured coatings. The chemically crosslinked moisture‐cured formulation based on PEG‐1000 and isophorone diisocyanate was prepared with NCO/OH ratio of 1.6:1.0. Trimethylol propane was used as a crosslinking agent. The excess isocyanate of the prepolymer was chain extended in the ratio of 2:1 (NCO/OH) with different aliphatic diols, and 4:1 with different aromatic diamines. The polymer network maturation during moisture cure was followed by dynamic mechanical thermal analyzer (DMTA) instrument. The thermal and dynamic mechanical properties of the crosslinked polymers were evaluated using thermogravimetric analysis, differential scanning calorimetric analysis and DMTA. Surface properties were evaluated through angle‐resolved X‐ray photoelectron spectroscopy. The present article discusses the physical properties of moisture‐cured polyurethane‐urea (MCPU) containing chemical crosslinks in the hard segment. The complete moisture‐cured polymers showed amorous results toward room temperature modulus, tensile strength, hardness, thermal stability, and transparency. The surface properties showed the enrichment of soft segments. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 102–118, 2006     

High performance UV cured polyurethane dispersion

Imide groups were introduced in the hard segment of UV cured polyurethane dispersion (UV-PUD) by extending the NCO terminated prepolymers with pyromellitic dianhydride (PMDA) where the soft segments were prepared from PTMG, H₁₂MDI, HDI and DMBA. It was found that imide hard segment, as compared with conventional urethane hard segment gave remarkably high mechanical properties as well as thermal stability in terms of decomposition temperature and dynamic mechanical properties at elevated temperatures, and the results were interpreted based on the partial mixing of soft segments and imide hard segments.     

Thermal stability enhancement of polyurethanes by surface treatment

Both oxidation and methoxymethylation of the surfaces of a series of MDI (methylene diphenyl isocyanate) and TDI (toluene diisocyanate) polyether and polyester soft segment 1–4 butanediol polyurethanes result in increased thermal stability as measured by TG. Explosive loss of mass above the hard segment melting temperature suggests that the diffusion of the dissociated diisocyanate moiety is hindered at lower temperatures. Thus suppression of the depolycondensation reaction by chemical blockage of the surface may result in a material with an increased service life at use temperatures as thermal stability of a polyurethane may depend upon the low diffusivity of its diisocyanate comonomer. The effect of vacuum, oxygen and water vapor on the kinetics of mass-loss of several of the polyurethanes is presented. In celebration of the 60^th birthday of Dr. Andrew K. Galwey     

Synthesis and characterization of novel h‐HTBN/PEG PU copolymers for tissue engineering: degradation,phase behavior,and mechanical properties

The phase behavior of the as‐prepared polyether polyurethane (PU) elastomers was investigated by dynamic mechanical analysis (DMA), polarized optical microscope (POM), and atomic force microscopy (AFM). This PU copolymers were composed of different compositions of two soft segments, poly(ethylene glycol) (PEG) and hydrolytically modified hydroxyl‐terminated poly(butadiene‐co‐acrylonitrile) (h‐HTBN) oligomers. The microphase separation behavior is confirmed to occur between soft and hard segments as well as soft and soft segments as the h‐HTBN is incorporated into the PU system, depending on soft‐soft and/or soft‐hard microdomain composition, molecular weight (MW) of PEG, and hydrolysis time of HTBN. The driving force for this phase separation is mainly due to the formation of inter‐ and intramolecular hydrogen bonding interaction. The PU‐70, PU‐50 samples with non‐reciprocal composition seem to exhibit larger microphase separation than any other PU ones. The hydrolysis degradation, thermal stability, and mechanical properties of the copolymers were assessed by gravimetry, scanning electron microscope (SEM), thermal gravity analysis (TGA), and tensile test, respectively. The experimental results indicated that the incorporation of h‐HTBN soft segment into PEG as well as low MW of PEG leads to increased thermal and degradable stability based on the intermolecular hydrogen bond interaction. The PU‐70 and PU‐50 copolymers exhibit better mechanical properties such as high flexibility and high ductility because of their larger microphase separation architecture with the hard domains acting as reinforcing fillers and/or physical crosslinking agents dispersed in the soft segment matrix. Copyright © 2009 John Wiley & Sons, Ltd.     

Dynamics and deformation behaviour in non-hydrogen bonded model urethanes under heat and stress as studied by dielectric and infrared spectroscopy

A model polyether-urethane with monodisperse N-alkyl polyurethane hard segment has been investigated by differential scanning calorimetry, dielectric spectroscopy and infrared spectroscopy. The temperature dependent changes in the enthalpic and dielectric properties have been correlated with specific molecular motions and transition processes in the hard and soft phase. The orientation of the hard and soft segments under uniaxial stress changes with the strain and mechanisms for the orientation and deformation behaviour have been proposed. Effects of the thermal history of the sample on the properties have been discussed as well.     

Effect of soft segment length on the thermal behaviors of fluorinated polyurethanes

Differential scanning calorimetry (DSC) and temperature modulated DSC (MDSC) have been applied to investigate the thermal behaviors of fluorinated polyurethanes (FPU), which were obtained using 2,2,3,3-tetrafluoro-1, 4-butanediol as the chain extender and based on various soft segments—polytetramethyl oxides (PTMO) with molecular weights of 650, 1000, 1400 and 2000. An exothermic peak and/or multiple melting endotherms were observed during the heating to melting temperature of soft and hard segments. Attributed to the simultaneous recrystallization and melting processes during heating, these features have been confirmed via MDSC, where an endotherm and an exotherm were noted in reversing and non-reversing components of the heat flow. Separating the non-reversing components from the reversing curves, the dependencies of polyurethane morphology on the length of the soft segment could be clarified using MDSC analysis. Soft segment lengthening significantly influences the morphology of soft segment domains in FPUs. The phase separation and crystallinity of the soft segment increased with its length. However, soft segment length exerted a minor influence on the dissociation temperature of the short-range ordered hard segment domain and on the melting temperature of hard segment crystals. Examination of the heats of melting based on the quasi-isothermal MDSC experiments indicated that the crystallinity of hard segment domains declined with increasing soft segment length.     

单组分聚氨酯清漆的制备与性能研究

不同的聚碳酸酯二元醇、聚四亚甲基醚二醇(PTMG)与二苯甲烷二异氰酸酯(MDI)、小分子二元醇反应,制得聚醚、聚碳酸酯型聚氨酯清漆。通过红外光谱分析结合其机械力学性能、耐水性等的测试结果,探讨聚碳酸酯型聚氨酯清漆的结构对形态和性能的影响。结果表明：随着硬段含量的增加,树脂涂膜的微相分离程度增加,机械性能提高;组分摩尔比例相同时,软段分子量的降低有利于提高树脂的软硬段相容性,增加树脂涂膜的物理机械性能;组分摩尔比例相同时聚酯型聚氨酯树脂的微相分离程度低于聚醚型聚氨酯树脂;MDI基溶剂型聚氨酯树脂的物理机械性能较好。