Synthetic Co50Pt50/Ru/CoFe hard–soft trilayer in spin valves

The influence of deposition power and seedlayer on the properties of hard magnet Co₅₀Pt₅₀ was studied. Co₅₀Pt₅₀(/Co₉₀Fe₁₀)/Ru/Co₉₀Fe₁₀ trilayer was used as pining/pinned layer in spin valves. The influences of different hard layer, soft layer and free layer on exchange bias, interlayer coupling, and magnetoresistance (MR) ratio were studied. Weak antiferromagnetic interlayer coupling was obtained by adjusting the thickness of hard and soft layers. MR of a spin valve with structure Cr2/CoFe0.5/CoPt4/CoFe0.5/Ru0.8/CoFe2.2/Cu2.05/CoFe2.6/Cu1.1/Ta1 reached 10.68% (unit in nm), which is comparable to those of IrMn-based synthetic spin valves. The increment of the coercivity of the free layer is mainly due to the static magnetic interaction between the hard layer and the free layer.     

Thermally activated magnetization reversal process of self-assembled Fe55Co45 nanowire arrays

We have investigated the temperature dependence of the magnetic properties and the magnetic relaxation of the Fe₅₅Co₄₅ nanowire arrays electrodeposited into self-assembled porous alumina templates with the diameter about 10 nm. X-ray diffraction (XRD) pattern indicates that the nanowire arrays are BCC structure with [1 1 0] orientation along the nanowire axes. Owing to the strong shape anisotropy, the nanowire arrays exhibit uniaxial magnetic anisotropy with the easy magnetization direction along the nanowire axes. The coercivity at 5 K can be explained by the sphere chains of the symmetric fanning mechanism. The temperature dependence of coercivity can be interpreted by thermally activated reversal mechanism as being the localized nucleation reversal mechanism with the activation volume much smaller than the wire volume. Strong field and temperature-dependent magnetic viscosity effects were also observed.     

快淬Nd3.6Pr5.4Fe83Co3B5薄带的反磁化行为和磁黏滞性

用电弧熔炼法制备了Nd_3.6Pr_5.4Fe₈₃Co₃B₅合金铸锭,然后利用熔旋快淬法在铜辊转速V=20m/s下制备了Nd_3.6Pr_5.4Fe₈₃Co₃B₅薄带.快淬带主要由软磁相α-Fe和Nd₂Fe₁₄B型的硬磁相组成.采用直流退磁剩磁曲线方法分析了样品在反磁化过程中的可逆与不可逆磁化部分,并研究了软磁相和硬磁相的反磁化行为,得到样品的不可逆磁化形核场H_no约为440kA/m.同时研究了样品的磁黏滞性,结果表明由于软磁相的存在使得热激活体积较大. 关键词：     

Synthesis,structures and magnetic properties of Pr-lean Pr2Fe14B/Fe3B nanocomposite alloys

The lean rare-earth Pr_4.5Fe_77−xTi_xB_18.5 (x=0, 1, 4, 5) nanocomposite alloys were prepared by melt spinning method and subsequent thermal annealing. The effect of Ti content and annealing temperature on the magnetic properties and the microstructure of these magnets were investigated. The enhancing coercivity H_c from 211.4 to 338.2 kA/m has been observed at the optimal annealing temperature of 700 °C by the addition of 5 at% Ti in Pr₂Fe₁₄B/Fe₃B alloys. It was also found that increasing Ti content leads to marked grain refinement in the annealed alloys, resulting in strong exchange-coupling interaction between the hard and the soft phases in these ribbons. In addition, the magnetization reversal behaviors of Pr₂Fe₁₄B/Fe₃B nanocomposites were discussed in detail.     

Magnetic,structural and electrical properties of ordered and disordered Co50Fe50 films

Co₅₀Fe₅₀ films with thickness varying from 100 to 500 Å were deposited on a glass substrate by sputtering process, respectively. Two kinds of CoFe films were studied: one was the as-deposited film, and the other the annealed film. The annealing procedure was to keep the films at 400 °C for 5 h in a vacuum of 5×10⁻⁶ mbar. From the X-ray study, we find that the as-deposited film prefers the CoFe(1 1 0) orientation. Moreover, the body-centered cubic (bcc) CoFe(1 1 0) line is split into two peaks: one corresponding to the ordered body-centered tetragonal (bct) phase, and the other, the disordered bcc phase. After annealing, the peak intensity of the ordered bct phase becomes much stronger, while that of the disordered bcc phase disappears. The annealing has also caused the ordered CoFe(2 0 0) line to appear. When the amount of the ordered bct phase in Co₅₀Fe₅₀ is increased, the saturation magnetization (M_s) and coercivity (H_c) become larger, but the electrical resistivity (ρ) decreases. From the temperature coefficient of resistance (TCR) measurement, we learn that the bct grains in the CoFe film start to grow at temperature 82 °C.     

Effects of oblique-incidence evaporation on magnetic properties of Fe20Ni80/Fe70Co30 bilayer film

Evaporative deposition at oblique incidence is shown to enhance the magnetic anisotropy of an Fe₂₀Ni₈₀ magnetic film and induce magnetic anisotropy in an overlying, strongly isotropic Fe₇₀Co₃₀ film. This deposition method for the formation of an underlayer of several lattice parameters in thickness and semi-hard overlayer of a few thousands Angstroms in thickness achieves a significant change in the magnetization process and strong suppression of the coercive forces of Fe₇₀Co₃₀ in the hard magnetization direction. Soft magnetization of the Fe₇₀Co₃₀ overlayer is not achieved when one of the layers is deposited at oblique incidence. It is anticipated that shape magnetic anisotropy is responsible in part for the magnetic anisotropy induced in both in Fe₂₀Ni₈₀ under- and Fe₇₀Co₃₀ overlayer by oblique incidence evaporation.     

Out-of-plane coercive field of Ni80Fe20 antidot arrays

The out-of-plane magnetic anisotropy and out-of-plane magnetization reversal process of nanoscale Ni₈₀Fe₂₀ antidot arrays deposited by magnetron sputtering technique on an anodic aluminum oxide (AAO) membrane are investigated. The angular dependence of out-of-plane remanent magnetization of Ni₈₀Fe₂₀ antidot arrays shows that the maximum remanence is in-plane and the squareness of the out-of-plane hysteresis loop follow a |cos θ| dependence. The angular dependence of out-of-plane coercivity of Ni₈₀Fe₂₀ antidot arrays shows that the maximum coercivity lies on the surface of a cone with its symmetric axis normal to the sample plane, which indicates a transition of magnetic reversal from curling to coherent rotation when changing the angle between the applied magnetic field and the sample plane.     

Magnetoelectric characterization of xNi0.75Co0.25Fe2O4-(1−x)BiFeO3 nanocomposites

Magnetoelectric (ME) nanocomposites containing Ni_0.75Co_0.25Fe₂O₄-BiFeO₃ phases were prepared by citrate sol-gel process. X-ray diffraction (XRD) analysis showed phase formation of xNi_0.75Co_0.25Fe₂O₄-(1−x)BiFeO₃ (x=0.1, 0.2, 0.3 and 0.4) composites on heating at 700 °C. Transmission electron microscopy revealed the formation of powders of nano order size and the crystal size was found to vary from 30 to 85 nm. Dispersion in dielectric constant (ε) and dielectric loss (tan δ) in the low-frequency range have been observed. It is seen that nanocomposites exhibit strong magnetic properties and a large ME effect. On increasing Ni_0.75Co_0.25Fe₂O₄ contents in the nanocomposites, the saturation magnetization (M_S) and coercivity (H_C) increased after annealing at 700 °C. The large ME output in the nanocomposites exhibits strong dependence on magnetic bias and magnetic field frequency. The large value of ME output can be attributed to small grain size of ferrite phase of nanocomposite being prepared by citrate precursor process.     

Study of domain structure and magnetization reversal after thermal treatments in Fe40Co38Mo4B18 microwires

We have studied the effect of thermal treatment on the magnetic domain structure and magnetic reversal process of amorphous and nanocrystalline Fe₄₀Co₃₈Mo₄B₁₈ microwires. The domain structure and the magnetization reversal of amorphous FeCoMoB microwires reflect the complex stress distribution introduced by the glass coating. Hence, the thickness of radial domain structure decreases with temperature and the temperature dependence of the switching field presents a discontinuous behavior. After nanocrystallization, the domain structure of FeCoMoB microwire is almost constant within the temperature range 10-400 K and the switching field decreases almost linearly with temperature mostly because of the decrease of saturation magnetization.     

Direct observation of dendritic domain growth in perpendicular magnetic anisotropy CoFe/Pt multilayers

We present the experimental results on thermally activated magnetization reversal for [Co_0.9Fe_0.1(5.0 Å)/Pt(20 Å)]₄ multilayer. Direct domain observations show that magnetization reversal is initiated with rare nucleation and followed by dendritic growth of domain walls. Based on macroscopic magnetic parameters from experimental data, the dendritic domain growth mode is qualitatively interpreted by Monte Carlo simulations in terms of a simple uniaxial magnetic anisotropy model. Moreover, both time evolution of domain growth observation and magnetic relaxation measurements reveal that CoFe/Pt multilayer has a relatively large activation volume compared with Co/Pt multilayers.     

MAGNETIC VISCOSITY OF NANOCOMPOSITE Sm-Fe-Cu-Zr-Ga-C RIBBONS

The magnetic viscosity was investigated at temperatures between 100 and 293 K for the nanocomposite Sm₂Fe_18.25Zr_0.25Cu_0.5Ga₂C₂ ribbons prepared by melt-spinning and subsequent annealing. It was found that the maximum S and χ_irr, located near coercivity, increase with increasing temperature. The viscosity parameter S_v was found to be strongly dependent on the applied fields at lower fields than the coercivities. The relation between S_v and coercivity was analyzed. The coercivity mechanism is mainly controlled by domain-wall pinning. The activation volume associated with magnetization reversal, which can be calculated from S_v, is much smaller than the grain volume.     

Preference orientation and magnetic properties of CoxFe3−xO4 nanocrystalline thin films on quartz substrate

Nanocrystalline spinel ferrite thin films of Co_xFe_3−xO₄ (x=0.3$x=0.3$, 0.5, 0.8, and 1.0) have been prepared by RF sputtering on quartz substrate without a buffer layer at room temperature and annealed at the temperature range from 200 to 600 °C in air. The as-sputtered films exhibit the preferred orientation and the high magnetization and coercivity. After annealing, the preferred orientations become poor, but the magnetization and coercivity increase. The sample with a magnetization of 455 emu/cm³, a coercivity of 2.8 kOe, a remanence ratio of 0.72, and a maximum energy product of 2.4 MGOe has been obtained. The influence of Co ions and annealing temperature on the magnetic properties has been discussed.     

Spin-dependent current and magnetization reversal in Tb22Co5Fe73/Pr6O11/Tb19Co5Fe76 nanofilms in laser radiation field

The results of investigation of magnetization reversal dynamics of ferrimagnetic amorphous nanolayers with transverse anisotropy is investigated for Al₂O₃/Tb₂₂Co₅Fe₇₃/Al₂O₃ and Al₂O₃/Tb₂₂Co₅Fe₇₃/Pr₆O₁₁/Tb₁₉Co₅Fe₇₆/Al₂O₃ multilayer films irradiated by laser pulses, as well as the effect of such irradiation on the resistance in a Tb₂₂Co₅Fe₇₃/Pr₆O₁₁/Tb₁₉Co₅Fe₇₆ tunnel microcontact. It is shown that magnetization reversal in magnetic nanolayers in the laser radiation field may occur not only because of heating and the action of the external magnetic field, but also under the action of the magnetic field induced by circularly polarized laser radiation, as well as owing to transfer of magnetic moments by polarized electrons. Laser radiation can be used to control (by changing the resistance by a factor of 1.5–2.0) the conductivity of the Tb₂₂Co₅Fe₇₃/Pr₆O₁₁/Tb₁₉Co₅Fe₇₆ tunnel microresistor. Original Russian Text ? N.N. Krupa, 2009, published in Zhurnal éksperimental’noĭ i Teoreticheskoĭ Fiziki, 2009, Vol. 108, No. 5, pp. 981–992.     

Exchange interaction effect of TbCo/FePt bilayers

Interlayer exchange coupling in dc-magnetron sputtered Tb_29.6Co_70.4/FePt bilayers with different annealing temperatures of the FePt film have been investigated. The dependence of ordering degree on perpendicular magnetic properties of the FePt film was studied. The Tb_29.6Co_70.4/FePt film has high perpendicular coercivity and high saturated magnetization about 7.5 kOe, and 302 emu/cm³, respectively as the substrate temperature is 500 °C and annealing at 500 °C for 30 min. It also shows a strong exchange coupling between this FePt layer and Tb_29.6Co_70.4 layer. We also examined the interface wall energy in the exchange coupled Tb_29.6Co_70.4/FePt double layers.     

Morphology and magnetic properties of Co0.8Fe2.2O4 films prepared by the chemical solution deposition

Co_0.8Fe_2.2O₄ ferrite thin films have been prepared on Si(0 0 1) substrates by the chemical solution deposition. Structural characteristics indicate all films are single phase with spinel structure and the space group and the mean grain size increases from 8 to 30 nm with the increase of annealing temperature. The magnetic properties of Co_0.8Fe_2.2O₄ thin films are highly dependent on annealing temperature. The sample annealed at 800 °C possesses high saturation magnetization, moderate coercivity and squareness ratio, making it a promising application candidate in high-density record and magneto-optical materials.     

Nd28Fe66B6/Fe50Co50双层纳米复合膜的结构和磁性

利用磁控溅射法制备了Nd₂₈Fe₆₆B₆/Fe_{50Co50 双层纳米复合磁性薄膜，研究了其结构和磁性.经873K退火处理15min 后，利用x射线衍射仪测定薄膜晶体结构，采用俄歇电子能谱仪估算薄膜厚度和超导量子干 涉仪测量其磁性.磁性测量表明，1)该系列薄膜具有垂直于膜面的磁各向异性.从起始磁化曲 线和小回线的形状特征可知，矫顽力机制主要是由畴壁钉扎控制.2)对于固定厚度（10nm） 层的硬磁相Nd-Fe-B和不同厚度（dFeCo=1—100nm）层软磁相FeCo双层纳米复合 膜,剩磁随软磁相FeCo 厚度的增加快速增加，而矫顽力则减少.当dFeCo=5nm 时 ，最大磁能积达到160×１０^３A/m.磁滞回线的单一硬磁相特征说明，硬磁相Nd -Fe-B层和软磁相FeCo层之间的相互作用使两相很好地耦合在一起.剩磁和磁能积的提高是由 于两相磁性交换耦合所致. 关键词： Nd-Fe-B/FeCo双层纳米复合膜 交换耦合 磁性增强}     

Effect of Ta buffer and NiFe seed layers on pulsed-DC magnetron sputtered Ir20Mn80/Co90Fe10 exchange bias

A systematic investigation has been done on the correlation between texture, grain size evolution and magnetic properties in Ta/Ni₈₁Fe₁₉/Ir₂₀Mn₈₀/Co₉₀Fe₁₀/Ta exchange bias in dependence of Ta buffer and NiFe seed layer thickness in the range of 2-10 nm, deposited by pulsed DC magnetron sputtering technique. A strong dependence of 〈1 1 1〉 texture on the Ta/NiFe thicknesses was found, where the reducing and increasing texture was correlated with exchange bias field and unidirectional anisotropy energy constant at both NiFe/IrMn and IrMn/CoFe interfaces. However, a direct correlation between average grain size in IrMn and H_ex and H_c was not observed. L1₂ phase IrMn₃ could be formed by thickness optimization of Ta/NiFe layers by deposition at room temperature, for which the maximum exchange coupling parameters were achieved. We conclude finally that the coercivity is mainly influenced by texture induced interfacial effects at NiFe/IrMn/CoFe interfaces developing with Ta/NiFe thicknesses.     

The size and space arrangement roles on coercivity of electrodeposited Co1−xCux nanowires

Magnetization curves with various magnetic field orientations and nanowire diameters were measured at room temperature. The measured coercivity as a function of angle (θ) between the field and wire axis reveals that the coercivity decreases with increasing value of θ for various nanowires. Theoretically, based on Monte Carlo simulation we investigated the magnetization reversal modes of the Co_1−xCu_x nanowires and obtained also the θ dependence of the coercivity. Comparing the simulated with the experimental results, we find that the magnetocrystalline anisotropy plays an important role on the magnetic properties of Co_1−xCu_x nanowires, and the magnetization reversal process in the Co_1−xCu_x nanowires could not be understood by the classical uniform rotation mode in the chain-of-sphere model.     

Dependence of magnetic characteristics on sputtering-power and substrate-temperature in amorphous Tb40(FeCoV)60 films

The amorphous Tb₄₀(Fe₄₉Co₄₉V₂)₆₀ films were deposited at different sputtering powers and substrate temperatures. The microstructural and magnetic characteristics were investigated by means of field emission scan electron microscope, magnetic force microscope and vibrating sample magnetometer. Our results show that with increasing sputtering power, out-of-plane coercivity decreases monotonically while saturation magnetization has a maximum value of 231 kA/m for the sample prepared at 50 W. The as-deposited alloy films are amorphous, whereas the coercivity and saturation magnetization are strongly dependent on the substrate temperature. An out-of-plane hysteresis loop with coercivity below 22 mT and saturation magnetization over 290 kA/m is obtained combining dc power and substrate temperature. The dominant mechanism of room temperature coercivity appears to be domain wall pinning, rather than nucleation under all conditions measured. The variation of saturation magnetization is similar to that of perpendicular magnetic anisotropy with either sputtering power or substrate temperature according to the difference of magnetic domain structure.     

Effects of annealing temperature on structure and magnetic properties of amorphous Fe61Co27P12 nanowire arrays

Arrays of Fe₆₁Co₂₇P₁₂ nanowire with an aspect ratio about 70 were prepared in anodic aluminum oxide templates by electrodeposition. The influences of annealing temperature on structure and magnetic properties of Fe₆₁Co₂₇P₁₂ nanowires were studied. When the specimens were annealed below 400 °C, there are no obvious changes in structure except relaxation. With the annealing temperature increasing from 400 to 600 °C, the Fe-Co phase is detected by X-ray diffraction and Mössbauer spectra. The crystalline fraction and hyperfine field can be derived from Mössbauer spectra. The room temperature magnetic hysteresis loops show that the coercivity and squareness of the nanowire arrays in parallel to the wire axis increase with the increasing of annealing temperature, which mainly attributes to the strengthening of anisotropy.