Chromatographic characterisation, under highly aqueous conditions, of a molecularly imprinted polymer binding the herbicide 2,4-dichlorophenoxyacetic acid

The affinity of a 2,4-dichlorophenoxyacetic acid (2,4-D) molecularly imprinted polymer (MIP), which was synthesised directly in an aqueous organic solvent, for its template (2,4-D) was studied and compared with the affinity exhibited by two other reference (control) polymers, NIPA and NIPB, for the same analyte. Zonal chromatography was performed to establish the optimal selectivity, expressed as imprinting factor (IF), under chromatographic conditions more aqueous than those described so far in the literature. Frontal analysis (FA) was performed on columns packed with these polymers, using an optimized mobile phase composed of methanol/phosphate buffer (50/50, v/v), to extract adsorption isotherm data and retrieve binding parameters from the best isotherm model. Surprisingly, the template had comparable and strong affinity for both MIP (K = 3.8 × 10⁴ M⁻¹) and NIPA (K = 1.9 × 10⁴ M⁻¹), although there was a marked difference in the saturation capacities of selective and non-selective sites, as one would expect for an imprinted polymer. NIPB acts as a true control polymer in the sense that it has relatively low affinity for the template (K = 8.0 × 10² M⁻¹). This work provides the first frontal chromatographic characterization of such a polymer in a water-rich environment over a wide concentration range. The significance of this work stems from the fact that the chromatographic approach used is generic and can be applied readily to other analytes, but also because there is an increasing demand for well-characterised imprinted materials that function effectively in aqueous media and are thus well-suited for analytical science applications involving, for example, biofluids and environmental water samples.     

Swellable molecularly imprinted polyN-(N-propyl)acrylamide particles for detection of emerging organic contaminants using surface plasmon resonance spectroscopy

Lightly crosslinked theophylline imprinted polyN-(N-propyl)acrylamide particles (ca. 300 nm in diameter) that are designed to swell and shrink as a function of analyte concentration in aqueous media were spin coated onto a gold surface. The nanospheres responded selectively to the targeted analyte due to molecular imprinting. Chemical sensing was based on changes in the refractive index of the imprinted particles that accompanied swelling due to binding of the targeted analyte, which was detected using surface plasmon resonance (SPR) spectroscopy. Because swelling leads to an increase in the percentage of water in the polymer, the refractive index of the polymer nanospheres decreased as the particles swelled. In the presence of aqueous theophylline at concentrations as low as 10⁻⁶ M, particle swelling is both pronounced and readily detectable. The full scale response of the imprinted particles to template occurs in less than 10 min. Swelling is also reversible and independent of the ionic strength of the solution in contact with the polymer. Replicate precision is less than 10⁻⁴ RI units. By comparison, there is no response to caffeine which is similar in structure to theophylline at concentrations as high as 1 × 10⁻² M. Changes in the refractive index of the imprinted polymer particles, as low as 10⁻⁴ RI units could be readily detected. A unique aspect of the prepared particles is the use of light crosslinking rather than heavy crosslinking. This is a significant development as it indicates that heavy crosslinking is not entirely necessary for selectivity in molecular imprinting with polyacrylamides.     

Determination of molybdenum in environmental samples

Molecular imprinted membrane of indole-3-ethanol (IE) was prepared by hybridization of IE imprinted polymer powder and polysulfone (PSf) membrane. The IE imprinted polymer by covalent imprinting method was synthesized with copolymerization of indole-3-ethyl methacrylate (IEMA) and divinylbenzene (DVB). The cross-linked P(IEMA-co-DVB) was ground to be powders having less than 63 μm size and then hybridized within PSf membrane by using phase inversion process. The resultant imprinted powder showed binding capacities of 1.8, 7.2, 0 and 0 μmol g⁻¹ for IE, indole, 8-hydroxyquinoline and pyrrole in aqueous solution, respectively, and after hybridization with the PSf membrane, the value was 46, 26, 0 and 0 μmol g⁻¹. As a result, it was found that the IE imprinted powder alone showed non-selectively binding to the IE, but, the hybridized powder within the PSf membrane bound selectively the IE. Evidence was presented that hydrophobic interaction of the PSf matrix caused the selective and efficient binding. We also showed separation behavior of the hybrid membranes and discussed on the binding selectivity of the IE molecule. In view point of hybrid effect of the PSf membrane and the cross-linked imprinted powder, the results of the separation of these substrates were considered.     

An optical sensor for the determination of digoxin in serum samples based on a molecularly imprinted polymer membrane

This paper reports the synthesis and testing of a molecularly imprinted polymer membrane for digoxin analysis. Digoxin-specific bulk polymer was obtained by the UV initiated co-polymerisation of methacrylic acid and ethylene glycol dimethacrylate in acetonitrile as porogen. After extracting the template analyte, the ground polymer particles were mixed with plasticizer polyvinyl chloride to form a MIP membrane. A reference polymer membrane was prepared from the same mixture of monomers but with no template. The resultant membrane morphologies were examined by scanning electron microscopy. The imprinted membrane was tested as the recognition element in a digoxin-sensitive fluorescence sensor; sensor response was measured using standard solutions of digoxin at concentrations of up to 4 × 10⁻³ mg L⁻¹. The detection limit was 3.17 × 10⁻⁵ mg L⁻¹. Within- and between-day relative standard deviations RSD (n = 5) were in the range 4.5-5.5% and 5.5-6.5% respectively for 0 and 1 × 10⁻³ mg L⁻¹ digoxin concentrations. A selectivity study showed that compounds of similar structure to digoxin did not significantly interfere with detection for interferent concentrations at 10, 30 and 100 times higher than the digoxin concentration. This simply manufactured MIP membrane showed good recognition characteristics, a high affinity for digoxin, and provided satisfactory results in analyses of this analyte in human serum.     

Comparison of pyrimethanil-imprinted beads and bulk polymer as stationary phase by non-linear chromatography

A pyrimethanil-imprinted polymer (P1) was prepared by iniferter-mediated photografting a mixture of methacrylic acid and ethylene dimethacrylate onto homemade near-monodispersed chloromethylated polydivinylbenzene beads. The chromatographic behaviour of a column packed with these imprinted beads was compared with another column packed with irregular particles obtained by grinding a bulk pyrimethanil-imprinted polymer (P2). The comparison was made using the kinetic model of non-linear chromatography, studying the elution of the template and of two related substances, cyprodinil and mepanipyrim. Extension of the region of linearity, capacity factors for the template and the related substances, column selectivity, binding site heterogeneity, apparent affinity constant (K) and lumped kinetic association (k_a) and dissociation rate constant (k_d) were studied during a large interval of solute concentration, ranging between 1 and 2000 μg/ml. From the experimental results obtained, in the linearity region of solute concentration column selectivity and binding site heterogeneity remained essentially the same for the two columns, while column capacity (at 20 μg/ml, P1 = 23.1, P2 = 11.5), K (at 20 μg/ml, P1 = 8.3 × 10⁶ M⁻¹, P2 = 2.5 × 10⁶ M⁻¹) and k_a (at 20 μg/ml, P1 = 3.5 μM⁻¹ s⁻¹, P2 = 0.47 μM⁻¹ s⁻¹) significantly increased and k_d (at 20 μg/ml, P1 = 0.42 s⁻¹, P2 = 0.67 s⁻¹) decreased for the column packed with the imprinted beads. These results are consistent with an influence of the polymerisation method on the morphology of the resulting polymer and not on the molecular recognition properties due to the molecular imprinting process.     

An electrochemical DNA-sensor developed with the use of methylene blue as a redox indicator for the detection of DNA damage induced by endocrine-disrupting compounds

An electrochemical biosensor capable of indirect detection of DNA damage induced by any one of the three endocrine-disrupting compounds (EDCs) – bisphenol A (BPA), 4-nonylphenol (NP) and 4-t-octylphenol (OP), has been researched and developed. The methylene blue (MB) dye was used as the redox indicator. The glassy carbon electrode (GCE) was modified by the assembled dsDNA/graphene oxide-chitosan/gold nano-particles to produce a dsDNA/GO-CS/AuNPs/GCE sensor. It was characterized with the use of electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and scanning electron microscopy (SEM) techniques. The loading/release of the MB dye by the dsDNA/GO-CS/AuNPs film was investigated, and the results showed that the process was reversible. Based on this, the sensor was used to measure the difference between the loading capabilities of intact and damaged dsDNA in the films. The sensor was then successfully applied to detect DNA damage electrochemically. The differential pulse voltammetry (DPV) peak current ratio for MB, observed before and after DNA damage, increased linearly in the presence the BPA, NP or OP compounds; the treatment range was 10–60 min, and the respective damage rates were 0.0069, 0.0044 and 0.0031 min⁻¹, respectively. These results were confirmed by the binding constants: 2.09 × 10⁶ M⁻¹ (BPA-DNA), 1.28 × 10⁶ M⁻¹ (NP-DNA) and 9.33 × 10⁵ M⁻¹ (OP-DNA), all of which were obtained with the use of differential pulse stripping voltammetry (DPSV).     

Synthesis and characterisation of molecularly imprinted catalytic microgels for carbonate hydrolysis

Novel molecularly imprinted microgels incorporating arginine and tyrosine side chains as functional monomers have been designed and synthesised with percentages of cross-linker ranging from 70 to 90%. Full chemico-physical characterisation including M_r, coil density and size particle determination concluded that all polymer preparations obtained can be classified as microgels. Molecular imprinting using a phosphate template was used to generate catalytic microgels for the hydrolysis of p-nitrophenyl carbonates. Kinetic characterisation of the catalytic activity of the different preparations indicated that values of critical monomer concentration (C_M) and percentage of cross-linker play an important role in determining the catalytic efficiency of the different preparations. Microgels containing 70% cross-linker were the only ones following the Michaelis-Menten saturation model and kinetic parameters were obtained using 4 mg/ml of M397: V_max = 1.34 × 10⁻⁶ M s⁻¹ (S.E. 1.28 × 10⁻⁷) and K_M = 2.38 × 10⁻³ M (S.E. 3.1 × 10⁻⁴).     

Synthesis of nano-sized arsenic-imprinted polymer and its use as As selective ionophore in a potentiometric membrane electrode: Part 1

In this study, a new strategy was proposed for the preparation of As (III)-imprinted polymer by using arsenic (methacrylate)₃ as template. Precipitation polymerization was utilized to synthesize nano-sized As (III)-imprinted polymer. Methacrylic acid and ethylene glycol dimethacrylate were used as the functional monomer and cross-linking agent, respectively. In order to assembly functional monomers around As (III) ion, sodium arsenite and methacrylic acid were heated in the presence of hydroquinone, leading to arsenic (methacrylate)₃. The nano-sized As (III) selective polymer was characterized by FT-IR and scanning electron microscopy techniques (SEM). It was demonstrated that arsenic was recognized as As³⁺ by the selective cavities of the synthesized IIP. Based on the prepared polymer, the first arsenic cation selective membrane electrode was introduced. Membrane electrode was constructed by dispersion of As (III)-imprinted polymer nanoparticles in poly(vinyl chloride), plasticized with di-nonylphthalate. The IIP-modified electrode exhibited a Nernstian response (20.4 ± 0.5 mV decade⁻¹) to arsenic ion over a wide concentration range (7.0 × 10⁻⁷ to 1.0 × 10⁻¹ mol L⁻¹) with a lower detection limit of 5.0 × 10⁻⁷ mol L⁻¹. Unlike this, the non-imprinted polymer (NIP)-based membrane electrode was not sensitive to arsenic in aqueous solution. The selectivity of the developed sensor to As (III) was shown to be satisfactory. The sensor was used for arsenic determination in some real samples.     

Preparation and performance analysis of PE-supported P(AN-co-MMA) gel polymer electrolyte for lithium ion battery application

Copolymer, poly(acrylonitrile-co-methyl methacrylate) (P(AN-co-MMA)), was synthesized by solution polymerization with different mole ratios of monomers, acrylonitrile (AN) and methyl methacrylate (MMA). Polyethylene (PE) supported copolymer and gel polymer electrolyte (GPE) were prepared with this copolymer and their performances were characterized with FTIR, TGA, SEM, and electrochemical methods. It is found that the GPE using the PE-supported copolymer with AN to MMA = 4:1 (mole) exhibits an ionic conductivity of 2.06 × 10⁻³ S cm⁻¹ at room temperature. The copolymer is stable up to 270 °C. The PE-supported copolymer shows a cross-linked porous structure and has 150 wt% of electrolyte uptake. The GPE is compatible with anode and cathode of lithium ion battery at high voltage and its electrochemical window is 5.5 V (vs. Li/Li⁺). With the application of the PE-supported GPE in lithium ion battery, the battery shows its good rate and initial discharge capacity and cyclic stability.     

Development of an optical fibre reflectance sensor for p-aminophenol detection based on immobilised bis-8-hydroxyquinoline

2,2′-(1,4-Phenylenedivinylene)bis-8-hydroxyquinoline (PBHQ), a highly sensitive reagent used for the colorimetric determination of p-aminophenol (PAP), was successfully immobilised on XAD-7 and coupled with optical fibres to investigate a sensor-based approach for determining p-aminophenol. The solid-state sensor is based on the reaction of PAP with PBHQ in presence of an oxidant to produce an indophenol dye. The reflectance measurements were carried out at a wavelength of 647 nm since it yielded the largest divergence different in reflectance spectra before and after reaction with the analyte. The linear dynamic range of PAP was found within the concentration range of 0.1-2.18 mg l⁻¹ with its LOD of 0.02 mg l⁻¹. The sensor response from different probes (n = 7) gave a R.S.D. of 4.4% at 1.09 mg l⁻¹ PAP concentration. The response time of the optical one-shot sensor was 5 min for a stable solution. As this PAP sensor is irreversible, a fresh sensor has to be used for each measurement. All the experimental parameters were optimized for the determination of PAP. Using the optical sensing probe, PAP in pharmaceutical wastewater and paracetamol was determined. The effect of potential interferences such as inorganic and organic compounds was also evaluated. Potential on-site determination of PAP with such sensors can indirectly aid detection of organo-phosphorus nerve agents and pesticides in the field by inhibition of acetylcholine esterase-catalyzed hydrolysis of p-aminophenyl acetate to p-aminophenol.     

Determining the stoichiometry and binding constants of inclusion complexes formed between aromatic compounds and β-cyclodextrin by solid-phase microextraction coupled to high-performance liquid chromatography

The complexation of native β-cyclodextrin (CD) and seven aromatic compounds, namely, phenetole, toluene, m-xylene, naphthalene, biphenyl, fluorene and phenanthrene, has been studied for first time utilizing a solid-phase microextraction (SPME)–high-performance liquid chromatography (HPLC) method. The stoichiometries of the analyte:β-CD complexes were found to be either 1:1 or 1:2. The formation of 1:2 complexes was confirmed for naphthalene, biphenyl, fluorene, and phenanthrene only when utilizing relatively high concentrations of β-CD (up to 6.6 mM). The 1:2 stoichiometries were confirmed using the classical modified Benesi–Hildebrand (BH) method. The calculated binding constants for 1:1 stoichiometries (K₁) using the SPME method varied from 115.3 M⁻¹ for toluene to 3510 M⁻¹ for phenanthrene, whereas the corresponding values to the 1:2 stoichiometries (K₃) varied from 7.30 × 10⁵ M⁻² for biphenyl to 9.03 × 10⁶ M⁻² for naphthalene.     

Bisphenol A-recognition polymers prepared by covalent molecular imprinting

A specific recognition material for bisphenol A (BPA) was prepared by using a covalent imprinting technique. A chloroform solution containing bisphenol A dimethacrylate as a template, ethylene glycol dimethacrylate as a cross-linking agent and 2,2′-azobis(isobutyronitrile) as an initiator was polymerized by UV initiation. When BPA was removed from the resulting polymer by hydrolysis of the ester bonds with aqueous sodium hydroxide, carboxylic acid residues were generated in the polymer. After the polymer was packed into a stainless steel column, retention factors of BPA and related compounds were measured. The imprinted polymer adsorbed BPA and structurally related compounds such as 4,4′-dihydroxybenzophenone, bis(4-hydroxyphenyl)sulfone and 4,4′-dihydroxybiphenyl. A typical association constant (K_a) was calculated to be 1.72×10⁵ M⁻¹ by Scatchard analysis. Interestingly, 17α- and 17β-estradiol were also bound to the imprinted polymer (K_a=1.68×10⁵ M⁻¹), indicating that the polymer could be used as artificial receptors for screening the compounds having estrogenic action.     

Molecular imprinted polymer-based chemiluminescence imaging sensor for the detection of trans-resveratrol

Sensitive, rapid and inexpensive chemiluminescence (CL) imaging has been developed based on molecular imprinted polymer (MIP) sensing elements. Imprinted uniform microspheres were synthesized by precipitation polymerization. Microtiter plates (96 wells) were coated with polymer microspheres imprinted with trans-resveratrol, which were fixed in place using poly(vinyl alcohol) (PVA) as glue. The amount of polymer-bound trans-resveratrol was quantified using imidazole (IMZ)-catalyzed peroxyoxalate chemiluminescence (PO-CL) reaction. The light produced was then measured with a high-resolution CCD camera. Calibration curve corresponding to analyte concentration ranging from 0.3 to 25 μg mL⁻¹ was obtained with a limit of detection 0.1 μg mL⁻¹. These results showed that the MIP-based CL imaging sensor can become a useful analytical tool for quick simultaneous detection of trans-resveratrol in a large number of real samples.     

Surface structure of thin asymmetric PS-b-PMMA diblock copolymers investigated by atomic force microscopy

Asymmetric poly(styrene-b-methyl methacrylate) (PS-b-PMMA) diblock copolymers of molecular weight M_n = 29,700 g mol⁻¹ (M_PS = 9300 g mol⁻¹M_PMMA = 20,100 g mol⁻¹, PD = 1.15, χ_PS = 0.323, χ_PMMA = 0.677) and M_n = 63,900 g mol⁻¹ (M_PS = 50,500 g mol⁻¹, M_PMMA = 13,400 g mol⁻¹, PD = 1.18, χ_PS = 0.790, χ_PMMA = 0.210) were prepared via reversible addition-fragmentation chain transfer (RAFT) polymerization. Atomic force microscopy (AFM) was used to investigate the surface structure of thin films, prepared by spin-coating the diblock copolymers on a silicon substrate. We show that the nanostructure of the diblock copolymer depends on the molecular weight and volume fraction of the diblock copolymers. We observed a perpendicular lamellar structure for the high molar mass sample and a hexagonal-packed cylindrical patterning for the lower molar mass one. Small-angle X-ray scattering investigation of these samples without annealing did not reveal any ordered structure. Annealing of PS-b-PMMA samples at 160 °C for 24 h led to a change in surface structure.     

Absorbance characteristics of a liquid-phase gas sensor based on gas-permeable liquid core waveguides

The absorbance characteristics and influential factors on these characteristics for a liquid-phase gas sensor, which is based on gas–permeable liquid core waveguides (LCWs), are studied from theoretical and experimental viewpoints in this paper. According to theory, it is predicted that absorbance is proportional to the analyte concentration, sampling time, analyte diffusion coefficient, and geometric factor of this device when the depletion layer of the analyte is ignored. The experimental results are in agreement with the theoretical hypothesis. According to the experimental results, absorbance is time-dependent and increasing linearly over time after the requisite response time with a linear correlation coefficient r² > 0.999. In the linear region, the rate of absorbance change (RAC) indicates improved linearity with sample concentration and a relative higher sensitivity than instantaneous absorbance does. By using a core liquid that is more affinitive to the analyte, reducing wall thickness and the inner diameter of the tubing, or increasing sample flow rate limitedly, the response time can be decreased and the sensitivity can be increased. However, increasing the LCW length can only enhance sensitivity and has no effect on response time. For liquid phase detection, there is a maximum flow rate, and the absorbance will decrease beyond the stated limit. Under experimental conditions, hexane as the LCW core solvent, a tubing wall thickness of 0.1 mm, a length of 10 cm, and a flow rate of 12 mL min⁻¹, the detection results for the aqueous benzene sample demonstrate a response time of 4 min. Additionally, the standard curve for the RAC versus concentration is RAC = 0.0267 c + 0.0351 (AU min⁻¹), with r² = 0.9922 within concentrations of 0.5–3.0 mg L⁻¹. The relative error for 0.5 mg L⁻¹ benzene (n = 6) is 7.4 ± 3.7%, and the LOD is 0.04 mg L⁻¹. This research can provide theoretical and practical guides for liquid–phase gas sensor design and development based on a gas-permeable Teflon AF 2400 LCW.     

Creatinine sensor based on a molecularly imprinted polymer-modified hanging mercury drop electrode

Molecularly imprinted polymers (MIP) have been elucidated to work as artificial receptors. In our present study, a MIP was applied as a molecular recognition element to a chemical sensor. We have constructed a creatinine sensor based on a MIP layer selective for creatinine and its differential pulse, cathodic stripping voltammetric detection (DPCSV) on a hanging mercury drop electrode (HMDE). The creatinine sensor was fabricated by the drop coating of dimethylformamide (DMF) solution of a creatinine-imprinted polymer onto the surface of HMDE. The modified-HMDE, preanodised in neutral medium at +0.4 V versus Ag/AgCl for 120 s, exhibited a marked enhancement in DPCSV current in comparison to the less anodised (≤+0.3 V) HMDE. The creatinine was preconcentrated and instantaneously oxidised in MIP layer giving DPCSV response in the concentration range of 0.0025-84.0 μg mL⁻¹ [detection limit (3σ) 1.49 ng mL⁻¹]. The sensor was found to be highly selective for creatinine without any response of interferents viz., NaCl, urea, creatine, glucose, phenylalanine, tyrosine, histidine and cytosine. The non-imprinted polymer-modified electrode did not show linear response to creatinine. The imprinting factor as high as 9.4 implies that the imprinted polymer exclusively acts as a recognition element of creatinine sensor. The proposed procedure can be used to determine creatinine in human blood serum without any preliminary treatment of the sample in an accurate, rapid and simple way.     

Sensing hydrogen peroxide involving intramolecular charge transfer pathway: A boronate-functioned styryl dye as a highly selective and sensitive naked-eye sensor

The synthesis, properties and applications of a novel boronate-functioned styryl dye, BSD, as a colorimetric sensor for hydrogen peroxide is presented. The dye displayed remarkable color change from colorless (λ_max = 391 nm) to deep red (λ_max = 522 nm) in the presence of H₂O₂ and the behavior could be rationalized by the chemoselective H₂O₂-mediated transformation of arylboronate to phenolate, resulting in the release of the merocyanine dye which featured with strong intramolecular charge transfer (ICT) absorption band. The absorption increment of merocyanine at λ_max = 522 nm (? = 87000 L mol⁻¹ cm⁻¹) is linear with the concentration of H₂O₂ in the range of 1.0 × 10⁻⁷-2.5 × 10⁻⁵ mol L⁻¹ with the detection limit of 6.8 × 10⁻⁸ mol L⁻¹ under optimum conditions. There is almost no interference by other species that commonly exist due to the specific deprotection of H₂O₂ towards arylboronate group on BSD. The chromogenic sensor has been applied to the detection of trace amounts of hydrogen peroxide in rain water.     

Construction of a novel molecularly imprinted sensor for the determination of O,O-dimethyl-(2,4-dichlorophenoxyacetoxyl)(3′-nitrophenyl)methinephosphonate

A novel voltammetric sensor for O,O-dimethyl-(2,4-dichlorophenoxyacetoxyl)(3′-nitrophenyl)methinephosphonate (Phi-NO₂) based on molecularly imprinted polymer (MIP) film electrode is constructed by using sol-gel technology. The sensor responds linearly to Phi-NO₂ over the concentration range of 2.0 × 10⁻⁵ to 1.0 × 10⁻⁸ mol L⁻¹ and the detection limit is 1.0 × 10⁻⁹ mol L⁻¹ (S/N = 3). This sensor provides an efficient way for eliminating interferences from coexisting substances in the solution. The high sensitivity, selectivity and stability of the sensor demonstrates its practical application for a simple and rapid determination of Phi-NO₂ in cabbage samples.     

Living radical polymerisation in heterogeneous conditions—suspension polymerisation

Transition metal mediated living radical polymerisation of butyl methacrylate has been demonstrated with a copper(I) halide N-alkyl-2-pyridylmethanimine ligands based catalyst. Optimum conditions were found to be with copper(I) chloride and N-octyl-2-pyridylmethanimine catalyst at 65 °C where conversions of 85% were achieved with polymers of M_n = 8900 g mol⁻¹ (theoretical = 8400 g mol⁻¹) and PDI = 1.23. Both non-ionic and ionic surfactants were employed which were also made by living radical polymerisation. The non-ionic surfactant was a block copolymer of PMMA from a polyethyleneglycol macroinitiator (total M_n = 7600 g mol⁻¹, PDI = 1.20) and the ionic surfactant PDMEAMA-PMMA (total M_n = 8000 g mol⁻¹, PDI = 1.21) with the PDMEAMA block quaternized with MeI (13.8%, 28.4%, 47.7% and 100%). A range of ligands were employed in the suspension polymerisation by varying the alkyl group on the ligand increasing the hydrophobicity (alkyl = propyl (PrMI), pentyl (PMI), octyl (OMI), dodecyl (DMI) and octadecyl (ODMI)). The more hydrophobic ligands were found to be more effective due to lower partitioning into the aqueous phase. Block copolymers of P(EMA)-P(BMA) and P(MMA)-P(BMA) were prepared by first preparing macroinitiators via living radical polymerisation (M_n = 1600 g mol⁻¹ (PDI = 1.23) for P(EMA) and M_n = 1500 g mol⁻¹ (PDI = 1.22) for P(MMA)) and using them for initiation of BMA in suspension polymerisation. Block copolymers had M_n between 12,800 and 13,700 g mol⁻¹ with PDI between 1.33 and 1.54. Block copolymer growth showed excellent linear first order kinetics wrt monomer and demonstrated characteristics expected of a living radical polymerisation. Particle sizes were measured by SEM and DLS with good agreement (1.4-2.8 μm) and SEM showed spherical particles were formed.     

Determination of solubility parameters of cross-linked macromonomeric initiators based on polypropylene glycol

A new type macromonomeric azo initiators also named macroinimers, MIMs, based on polypropylene glycol, PPG, with molecular weight 400 and 2000, were synthesized. Self-condensing radical polymerization of the macroinimers gave cross-linked polypropylene glycols. The solubility parameters of the cross-linked polymers determined using swelling experiments in a series of solvents have been reported. Crosss-linked PPG-400 and cross-linked PPG-2000 indicated the same solubility parameter value. But their swelling ratios were different because of the differences of the chain lengths in between of the cross-points (Mc) of the gels. Therefore, while the largest swelling ratio exhibited by a cross-linked PPG-2000 in tetrahydrofurane was being 19.48, this ratio was 6.84 for the cross-linked PPG-400 in the same solvent. The solubility parameters and constant α for these cross-linked polymers were obtained as δ_{cross-linked PPG-400} = 9.56 (cal cm⁻³)^1/2, α = 0.123 cm³ cal⁻¹ and δ_{cross-linked PPG-2000} = 8.95 (cal cm⁻³)^1/2, α = 0.107 cm³ cal⁻¹ by using the least squares regression method.