Wholly aromatic thermotropic liquid crystalline polyesters of 3,3′-bis(phenyl)-4,4′-biphenol with 4,4′-benzophenone dicarboxylic acid

A series of wholly aromatic, thermotropic polyesters, derived from 3,3′-bis(phenyl)-4,4′-biphenol (DPBP), nonlinear 4,4′-benzophenone dicarboxylic acid (4,4′-BDA), and various linear comonomers, were prepared by the melt polycondensation reaction and characterized for their thermotropic properties by a variety of experimental techniques. The homopolymer of DPBP with 4,4′-BDA had a fusion temperature (T_f) at 265°C, exhibited a nematic phase, and had a liquid crystalline range of 105°C. All of the copolyesters of DPBP with 4,4′-BDA and either 30 mol % 4-hydroxybenzoic acid (HBA), 6-hydroxy-2-naphthoic acid (HNA), or 50 mol % terephthalic acid (TA), 2,6-naphthalenedicarboxylic acid (2,6-NDA) had low T_f values in the range of 220–285°C, exhibited a nematic phase, and had accessible isotropization transitions (T_i) in the range of 270–420°C, respectively. Their accessible T_i values would enable one to observe a biphase structure. Each of the copolymers with HBA or HNA had a much broader range of liquid crystalline phase. In contrast, each of the copolymers with TA or 2,6-NDA had a relatively narrow range of liquid crystalline phase. Each of these polyesters had a glassy, nematic morphology that was confirmed with the DSC, PLM, WAXD, and SEM studies. As expected, they had higher glass transition temperatures (T_g) in the range of 161–217°C than those of other liquid crystalline polyesters, and excellent thermal stabilities (T_d) in the range of 494–517°C, respectively. Despite their noncrystallinity, they were not soluble in common organic solvents with the exception that the homopolymer and its copolymer with TA had limited solubility in CHCl₃. However, they were soluble in the usual mixture of p-chlorophenol/1,1,2,2-tetrachloroethane (60/40 by weight) with the exception of the copolymer with 2,6-NDA. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 769–785, 1997     

A synchrotron SAXS study of miscible blends of semicrystalline poly(vinylidenefluoride) and semicrystalline poly(1,4‐butylene adipate). II. Crystallization,morphology, and PBA inclusion in PVF2 spherulites

The incorporation of poly(1,4‐butylene adipate) (PBA) and its crystallization behavior within poly(vinylidenefluoride) (PVF₂) spherulites in miscible PVF₂/PBA blends have been further studied with small‐angle X‐ray synchrotron scattering (SAXS). The incorporation of PBA into the PVF₂ interlamellar region was found to be dependent on the PVF₂ crystallization conditions. In our previous work, where the blends were crystallized by a one‐step quenching process directly from 190 (a single‐phase region) to 20 °C (a three‐phase region), the transition from PBA inclusion in the PVF₂ interlamellar region to interlamellar exclusion occurred at a PBA weight fraction of ∼ 0.5. In this case, where the blends were first quenched from 190 (a single‐phase region) to 130 °C (a two‐phase region) and then further quenched to 20 °C (a three‐phase region), the transition occurred at a PBA weight fraction of less than 0.3. That is, when a blend is crystallized under different conditions, different amounts of the PBA component are incorporated into the PVF₂ interlamellar phase. The thickness of the PVF₂ interlamellar phase, in turn, may affect the PBA crystalline structure in the interlamellar region. Time‐resolved SAXS was used to probe the crystallization dynamics of both PVF₂ and PBA components in a blend containing 60 wt % PBA. The blend was quenched from the single‐phase region at 190 to 130 °C to crystallize the PVF₂ component and was then further quenched to 20 °C to crystallize the PBA component. This study, together with our earlier results, shows that the time dependence of the PVF₂ crystallization rate and crystalline lamellar thickness is a function of the PBA content in the blend. The glass‐transition temperature of the blend and the PBA diffusion process are the two dominant factors that control the PVF₂ crystallization dynamics. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2296–2308, 2000     

Elastic modulus of the crystalline regions of chitin and chitosan

The elastic moduli E_l of the crystalline regions of α‐chitin and chitosan in the direction parallel to the chain axis were measured by X‐ray diffraction. The E_l values were 41 GPa for α‐chitin, and 65 GPa for chitosan, respectively, at 20°C. The contracted skeletons of α‐chitin and chitosan are the key factor for the low E_l values compared with that (138 GPa) of cellulose I. The E_l value of α‐chitin was constant at 41 GPa both at −190°C and 150°C, which indicates that the molecular chain of α‐chitin is stable against heat within the temperature and stress range studied. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1191–1196, 1999     

Copolymerization of hexafluoropropylene and tetrafluoroethylene: Effect on chain conformation and crystal structure

A series of new copolymers of tetrafluoroethylene (TFE) and hexafluoropropylene (HFP) containing up to 50 mol % of the hexafluoropropylene comonomer have been investigated with respect to chain conformation and crystal structure using wide-angle X-ray diffraction (WAXD). Increasing HFP content leads to significant departures from the highly ordered crystalline structure of the homopolymer PTFE; the helical conformation of the chain relaxes and untwists to accommodate the larger  CF₃ pendant group in the HFP unit. Simultaneously the lateral hexagonal packing of the helices becomes less ordered and the a-dimension of the hexagonal cell increases. The above effects are progressive with increasing HFP content. At 50 mol % HFP incorporation the structure is a disordered crystalline phase. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 2811–2819, 1998     

Morphology,crystal structure,and orientation of poly-p-oxybenzoate on mica

Polymerization of p-acetoxybenzoic acid between mica sheets, from both the melt and dilute solution, in a wide range of polymerization temperatures (180–400°C) yields an epitaxial-like overgrowth of PpOBA on the mica cleavage surface. The PpOBA overgrowth forms long rows by lateral aggregation of ribbon crystals situated in three substrate directions rotated by 60°. The c-axes of the PpOBA phase I and II lattices are parallel to the 001 plane of the mica, coinciding with the a-axes of the mica hexagonal structure. The a_I- and b_II-axes lie predominantly on the mica surface. The surface-orienting effect is tentatively attributed to surface steps and or/polar effects; lattice matching does not occur. The recrystallization of bulk polymer samples previously prepared also leads to ordering between mica like that in melt or solution polymerization. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 1807–1820, 1997     

Crystalline structure of polyamide 12 as revealed by solid‐state 13C NMR and synchrotron WAXS and SAXS

The crystalline structure of polyamide‐12 (PA12) was studied by solid‐state ¹³C nuclear magnetic resonance (NMR) as well as by synchrotron wide‐ and small‐angle X‐ray scattering (WAXS and SAXS). Isotropic and oriented PA12 showed different NMR spectra ascribed to γ‐ and γ′‐crystalline modifications, respectively. On the basis of the position of the first diffraction peak, the isotropic γ‐form and the oriented γ′‐form were shown to be with hexagonal crystalline lattice at room temperature. When heated, the two PA12 polymorphs demonstrated different behaviors. Above 140 °C, the isotropic γ‐PA12 partially transformed into α‐modification. No such transition was observed with the oriented γ′‐PA12 phase even after annealing at temperatures close to melting. A γ′–γ transition was observed here only after isotropization by melting point. Various structural parameters were extracted from the WAXS and SAXS patterns and analyzed as a function of temperature and orientation: the degree of crystallinity, the d‐spacings, the Bragg's long spacings, the average thicknesses of the crystalline (l_c) and amorphous (l_a) phases, and the linear crystallinity x_cl within the lamellar stacks. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3720–3733, 2005     

Orientation of uniaxially stretched poly(ethylene naphthalene 2,6‐dicarboxylate) films by polarized infrared spectroscopy

Poly(ethylene naphthalene‐2,6‐dicarboxylate) has been uniaxially stretched at different draw ratios and at two different temperatures below and above its glass transition (T_g ～ 120 °C) respectively, at 100 and 160 °C. Crystallinity has been evaluated from calorimetric analyses and compared to the values deduced by FTIR spectroscopic data. As expected, the obtained results are quite similar and show that films stretched at lower temperature (100 °C) are more crystalline than those stretched at 160 °C. Optical anisotropy associated with orientation has been evaluated by birefringence and show that films stretched at 100 °C are more birefringent than those stretched at 160 °C as a result of a higher chain relaxation above T_g. Polarized FTIR was also performed to evaluate the individual orientation of amorphous and crystalline phases by calculating dichroic ratios R and orientation functions 〈P₂(cos θ)〉 and also show that amorphous and crystalline phases are more oriented in the case of films stretched below T_g. Nevertheless, the orientation of the amorphous phase is always weaker than that of the crystalline phase. Films stretched at 100 °C show a rapid increase in orientation (and crystallinity) with draw ratio and 〈P₂(cos θ)〉 reaches a limit value when draw ratio becomes higher than 3.5. Films drawn at 160 °C are less oriented and their orientation is increasing progressively with draw ratio without showing a plateau. A careful measurement of the IR absorbance was necessary to evaluate the structural angles of the transition moments to the molecular chain axis. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1950–1958, 2007     

Studies on the synthesis and properties of ferroelectric side chain liquid crystalline polyoxetanes

Two series of novel ferroelectric liquid crystalline (FLC) monomers were derived from 3-(hydroxymethyl)-3-methyloxetane, used as the backbone unit, and 2-(S)-[2-(S)-methylbutoxy]propionic acid, as a chiral moiety. The corresponding polyoxetanes were prepared by ring-opening polymerization using BF₃ · OEt₂ as an initiator. In addition to the structure identification, their liquid crystal phase behavior and electrical properties are also studied. Before their connection to the chiral molecular moiety, two series of carboxylic acids, 4-(6-[(3-methyloxetan-3-yl)methoxy]alkoxy)-benzoic acids and 4,4′-[6-(3-methyloxetan-3-yl)alkoxy]biphenylcarboxylic acids, show the phase sequence K Sc I and K Sc N I, respectively. After connection, the phase behavior of the corresponding chiral monomers is changed from K Sc I to K Sc* N* I as well as from K Sc N I to K Sc* Sa I. Only the phase sequence K Sc* Sa I is observed in both series of polyoxetanes. All of the synthesized monomers exhibited enantiotropic chiral smectic C(Sc*) phase. The monomers, with the biphenyl unit linked directly with a chiral center, possessed higher spontaneous polarization (P_s) values. Polyoxetanes possess a wide temperature range for the liquid crystal phase, about 120°C, and the Sc* phase range can be up to 95°C. However, the position of the biphenyl unit will not affect the spontaneous polarization of the synthesized side chain FLC polyoxetanes. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35 : 2843–2855, 1997     

Influence of molecular arrangement on the γ-ray-irradiation solid-state polymerization of 1-octadecyl vinyl ether with a characteristic polymorphism

The polymorphic behavior of 1-octadecyl vinyl ether was investigated by DSC and X-ray diffraction measurements under various temperatures. In DSC measurement of 1-octadecyl vinyl ether in the temperature range of −30 to approximately 50°C, four transition peaks were observed on heating, whereas three transition peaks appeared on cooling. The phase-transition behavior was investigated by the repeating scanning DSC measurements. It was concluded that this compound exhibited four crystalline modifications: α, sub α, β₀, and β₁. It was confirmed by the temperature-controlled X-ray diffraction measurement that these phase transitions are attributed to the change of crystal systems from hexagonal packing (α form) to a distorted orthorhombic (O⟂′) system (β₁ form) via orthorhombic (O⟂) (sub α form) and intermediate β₀ form, although the β₀ form has not yet been clarified. In the γ-ray-irradiation solid-state polymerization for these crystal forms of this compound, the polymerizability of the sub α form is higher than that of other forms, and that of the α form is lowest. The polymerizability demonstrated an unusual increase at a temperature of −83.6°C, probably because the cationic polymerization mechanism is dominant over that of the free radical. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 3845–3853, 1999     

Characterization and degradation of poly(methylphenylsiloxane)–poly(methyl methacrylate) interpenetrating polymer networks

Poly(methylphenylsiloxane)–poly(methyl methacrylate) interpenetrating polymer networks (PMPS–PMMA IPNs) were prepared by in situ sequential condensation of poly(methylphenylsiloxane) with tetramethyl orthosilicate and polymerization of methyl methacrylate. PMPS–PMMA IPNs were characterized by infrared (IR), differential scanning calorimetry (DSC), and ²⁹Si and ¹³C nuclear magnetic resonance (NMR). The mobility of PMPS segments in IPNs, investigated by proton spin–spin relaxation T₂ measurements, is seriously restricted. The PMPS networks have influence on the average activation energy E_a,av of MMA segments in thermal degradation at initial conversion. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1717–1724, 1999     

Effect of annealing on the structure and properties of poly(vinylidene fluoride) β‐form films

Oriented poly(vinylidene fluoride) (PVDF) films consisting of β crystals were prepared by the solid‐state coextrusion (SC) of a gel film near the melting temperature (T_m) and by conventional cold tensile drawing (TD) of a melt‐quenched film. These films were annealed over the temperature range of 75–190 °C (below and above the static T_m) while the sample length was kept constant or constant loads were applied. After annealing with the sample length kept constant, the dynamic Young's modulus markedly decreased because of the relaxation of oriented amorphous chains, as shown by infrared spectroscopy. In contrast, annealing under a constant load improved the chain orientation in both the crystalline and amorphous regions, resulting in an increase in the modulus from an initial 10.5 to 14.3 GPa for the SC and from an initial 3.3 to 4.8 GPa for the TD. The SC, annealed at 190 °C with a constant load corresponding to an initial tension of 200 MPa, exhibited an extreme crystalline‐chain orientation of 0.998 and a modulus of 14.3 GPa, among the highest values ever reported for PVDF. Although the remanent polarization (P_r) of the TD increased slightly from the initial 62 to 68 mC/m², P_r of the SC stayed constant at 100 mC/m² independently of the annealing conditions. This suggests that the P_r value of 100 mC/m² approached the equilibrium value for this PVDF sample containing 3.5 mol % structural defects. Therefore, although the modulus and P_r of the TD increased slightly with annealing, the maximum values achieved by annealing were markedly lower than those of the SC and annealed SC. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1701–1712, 2003     

Nylon 6 9 can crystallize with hydrogen bonding in two and in three interchain directions

Nylon 6 9 has been shown to have structures with interchain hydrogen bonds in both two and in three directions. Chain-folded lamellar crystals were studied using transmission electron microscopy and sedimented crystal mats and uniaxially oriented fibers studied by X-ray diffraction. The principal room-temperature structure shows the two characteristic (interchain) diffraction signals at spacings of 0.43 and 0.38 nm, typical of α-phase nylons; however, nylon 6 9 is unable to form the α-phase hydrogen-bonded sheets without serious distortion of the all-trans polymeric backbone. Our structure has c and c^* noncoincident and two directions of hydrogen bonding. Optimum hydrogen bonding can only occur if consecutive pairs of amide units alternate between two crystallographic planes. The salient features of our model offer a possible universal solution for the crystalline state of all odd–even nylons. The nylon 6 9 room-temperature structure has a C-centered monoclinic unit cell (β = 108°) with the hydrogen bonds along the C-face diagonals; this structure bears a similarity to that recently proposed for nylons 6 5 and X3. On heating nylon 6 9 lamellar crystals and fibers, the two characteristic diffraction signals converge and meet at 0.42 nm at the Brill temperature, T_B · T_B for nylon 6 9 lamellar crystals is slightly below the melting point (T_m), whereas T_B for nylon 6 9 fibers is ≅ 100°C below T_m. Above T_B, nylon 6 9 has a hexagonal unit cell; the alkane segments exist in a mobile phase and equivalent hydrogen bonds populate the three principal (hexagonal) directions. A structure with perturbed hexagonal symmetry, which bears a resemblance to the reported γ-phase for nylons, can be obtained by quenching from the crystalline growth phase (above T_B) to room temperature. We propose that this structure is a “quenched-in” perturbed form of the nylon 6 9 high-temperature hexagonal phase and has interchain hydrogen bonds in all three principal crystallographic directions. In this respect it differs importantly from the γ-phase models. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1153–1165, 1998     

Effects of molecular characteristics and processing conditions on melt‐drawing behavior of ultrahigh molecular weight polyethylene

The effects of molecular characteristics and processing conditions on melt‐drawing behavior of ultrahigh molecular weight polyethylene (UHMW‐PE) are discussed, based on a combination of in situ X‐ray measurement and stress–strain behavior. The sample films of metallocene‐ and Ziegler‐catalyzed UHMW‐PEs with a similar viscosity average MW of ～10⁷ were prepared by compression molding at 180 °C. Stress profiles recorded at 160 °C above the melting temperature of 135 °C exhibited a plateau stress region for both films. The relative change in the intensities of the amorphous scattering recorded on the equator and on the meridian indicated the orientation of amorphous chains along the draw axis with increasing strain. However, there was a substantial difference in the subsequent crystallization into the hexagonal phase, reflecting the molecular characteristics, that is, MW distribution of each sample film. Rapid crystallization into the hexagonal phase occurred at the beginning point of the plateau stress region in melt‐drawing for metallocene‐catalyzed UHMW‐PE film. In contrast, gradual crystallization into the hexagonal phase occurred at the middle point of the plateau stress region for the Ziegler‐catalyzed film, suggesting an ease of chain slippage during drawing. These results demonstrate that the difference in the MW distribution due to the polymerization catalyst system dominates the phase development mechanism during melt‐drawing. The effect of the processing conditions, that is, the including strain rate and drawing temperature, on the melt‐drawing behavior is also discussed. The obtained results indicate that the traditional temperature–strain rate relationship is effective for transient crystallization in to the hexagonal phase during melt‐drawing, as well as for typically oriented crystallization during ultradrawing in the solid state. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2455–2467, 2006     

Fully aromatic thermotropic liquid crystalline polyesters of 3-phenyl-4,4′-biphenol with 4,4′-benzophenone dicarboxylic acid

A series of fully aromatic, thermotropic polyesters, derived from 3-phenyl-4,4′-biphenol (MPBP), nonlinear 4,4′-benzophenone dicarboxylic acid (4,4′-BDA), and various other comonomers was prepared by the melt polycondensation method and characterized for their thermotropic liquid crystalline behavior by a variety of experimental techniques. The homopolymer of MPBP with 4,4′-BDA had a fusion temperature (T_f) at 240°C, exhibited a nematic liquid crystalline phase, and had a narrow liquid crystalline range of 60°C. All of the copolyesters of MPBP with 4,4′-BDA and either 30 mol % 4-hydroxybenzoic acid (HBA), 6-hydroxy-2-naphthoic acid (HNA) or 50 mol % terephthalic acid (TA), 2,6-naphthale-nedicarboxylic acid (2,6-NDA) and low T_f values in the range of 210–230°C, exhibited a nematic phase, and had accessible isotropization transitions (T_i) in the range of 320–420°C, respectively. As expected, each of them had a broader range of liquid crystalline phase than the homopolymer. They had a “frozen” nematic, glassy order as determined with the wide-angle X-ray diffraction (WAXD) studies. The morphology of each of the “as-made” polyesters had a fibrous structure as determined with the scanning electron microscopy (SEM), which arises because of the liquid crystalline domains. Moreover, they had higher glass transition temperatures (T_g) in the range of 167–190°C than those of other liquid crystalline polyesters, and excellent thermal stabilities (T_d) in the range of 500–533°C, respectively. © 1995 John Wiley & Sons, Inc.     

Conformational variation and crystalline phase transformation of low syndiotactic polypropylene films in stretched and stress‐relaxed states

Low syndiotactic polypropylene (sPP; rrrr = 80%) films were isothermally crystallized at 0 °C (sample S₀) and 90 °C (sample S₉₀) for 65 h, respectively. Fourier transform infrared spectroscopy, differential scanning calorimetry, and wide‐angle X‐ray diffraction were used to characterize the structure transformation and orientation behavior of samples S₀ and S₉₀ at both stretched and stress‐relaxed states. It was found that stretching (λ = 0–700%) induces the transformation of the chain conformation from helical to trans‐planar form for both S₀ and S₉₀ films. The stretched S₀ and S₉₀ samples show well oriented trans‐planar chains as well as partially retained helices. Simultaneously, crystalline phase transformation occurs during the stretching and relaxing processes of the investigated sPP samples, i.e., stable form I crystals can be transformed into metastable form III or mesophase by stretching samples, and vice versa. For stretched S₀ sample, form III with trans‐planar conformation, which generally exists in highly stretched sPP, cannot be observed, even at higher strains. For sample S₉₀, however, stretching might induce the formation of both the form III crystals and mesophase with trans‐planar chains; releasing the tension, form III again gets converted into trans‐planar mesophase and form I crystals. In the stretched and stress‐relaxed states of samples S₀ and S₉₀, the difference of the delicate orientation behavior and relative content of chain conformation and crystalline form can be attributed to the different heat‐treating methods of the low syndiotacticity sPP. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2924–2936, 2005     

Crystallization kinetics of a thermotropic liquid crystalline polyimide derived from 1,3-bis[4-(4′-aminophenoxy) cumyl] benzene

We have studied the nonisothermal and isothermal crystallization kinetics of an aromatic thermotropic liquid crystalline polyimide synthesized from 1,2,4,5-benzenetetracarboxylic dianhydride (PMDA) and 1,3-bis[4-(4′-aminophenoxy) cumyl] benzene (BACB) by means of differential scanning calorimetry (DSC). Polarized light microscopy (PLM) and wide-angle X-ray diffraction (WAXD) results confirm that this polyimide exhibits a smectic texture. Nonisothermal crystallization showed two strong and one weak exothermic peaks during cooling. The phase transition from isotropic melt to liquid crystalline state is extremely fast which completes in several seconds. The mesophase transition has a small Avrami parameter, n, of approximate 1. The isothermal crystallization of 253–258°C has been examined. The average value n is about 2.6 and the temperature-dependent rate constant k changes about two orders of magnitude in the crystallization temperature range of 6°C. The slope of ln k versus 1/(T_cΔT) is calculated to be −2.4 × 10⁵, which suggests nucleation control, via primary and/or secondary nucleation for the crystallization process. During the annealing process, a new phase (slow transition) is induced, which grows gradually with annealing time. At lower annealing temperatures (220–230°C), the slow transition process seems not to be influenced by the crystals formed during cooling process and its Avrami parameter n is ca. 0.3–0.4. However, the slow transition was hindered by the crystals formed during cooling process when annealed at higher temperature (230–240°C). © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1679–1694, 1998     

Morphology of polylactic acid crystallized during annealing after uniaxial deformation

Uniaxial deformation of amorphous L -polylactic acid films was performed at two different temperatures at which thermal degradation was minimal, 70 °C or T_g + 10 and 90 °C or T_g + 30. Samples were annealed postdeformation for long times (either 15 or 45 min) to approach equilibrium conditions. Samples deformed and annealed at 70 °C showed low crystallinity and poor crystalline order or crystal size, as determined by wide-angle X-ray diffraction. At 90 °C, high crystallinity and order parameters were observed. In addition, once the oriented chains had crystallized at this temperature, nonoriented chains also underwent crystallization, and a small fraction of nonordered crystal phase was therefore observed after long annealing times. These observations are explained on the basis of different morphologies in samples drawn at the two temperatures. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2013     

Synthesis of comb‐type polycarbosilanes via nucleophilic substitution reactions on the main‐chain silicon atoms

A series of comb‐type polycarbosilanes of the type [Si(CH₃)(OR)CH₂]_n {where R = (CH₂)_mR′, R′ = ? O‐p‐biphenyl? X [X = H (m = 3, 6, 8, or 11) or CN (m = 11)], and R′ = (CF₂)₇CF₃ (m = 4)} were prepared from poly(chloromethylsilylenemethylene) by reactions with the respective hydroxy‐terminated side chains in the presence of triethylamine. The product side‐chain polymers were typically greater than 90% substituted and, for R′ = ? O‐p‐biphenyl? X derivatives, they exhibited phase transitions between 27 and 150 °C involving both crystalline and liquid‐crystalline phases. The introduction of the polar p‐CN substituent to the biphenyl mesogen resulted in a substantial increase in both the isotropization temperature and the liquid‐crystalline phase range with respect to the corresponding unsubstituted biphenyl derivative. For R = (CH₂)₁₁? O‐biphenyl side chains, an analogous side‐chain liquid‐crystalline (SCLC) polysiloxane derivative of the type [Si(CH₃)(O(CH₂)₁₁? O‐biphenyl)O]_n was prepared by means of a catalytic dehydrogenation reaction. In contrast to the polycarbosilane bearing the same side chain, this polymer did not exhibit any liquid‐crystalline phases but melted directly from a crystalline phase to an isotropic liquid at 94 °C. Similar behavior was observed for the polycarbosilane with a fluorocarbon chain, for which a single transition from a crystalline phase to an isotropic liquid was observed at ?0.7 °C. The molecular structures of these polymers were characterized by means of gel permeation chromatography and high‐resolution NMR studies, and the crystalline and liquid‐crystalline phases of the SCLC polymers were identified by differential scanning calorimetry, polarized optical microscopy, and X‐ray diffraction. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 984–997, 2003     

Lateral thermal expansion of cellulose Iβ and IIII polymorphs

Measurements of the thermal expansion coefficients (TECs) of cellulose crystals in the lateral direction are reported. Oriented films of highly crystalline cellulose I_β and III_I were prepared and then investigated with X‐ray diffraction at specific temperatures from room temperature to 250 °C during the heating process. Cellulose I_β underwent a transition into the high‐temperature phase with the temperature increasing above 220–230 °C; cellulose III_I was transformed into cellulose I_β when the sample was heated above 200 °C. Therefore, the TECs of I_β and III_I below 200 °C were measured. For cellulose I_β, the TEC of the a axis increased linearly from room temperature at α_a = 4.3 × 10^?5 °C^?1 to 200 °C at α_a = 17.0 × 10^?5 °C^?1, but the TEC of the b axis was constant at α_b = 0.5 × 10^?5 °C^?1. Like cellulose I_β, cellulose III_I also showed an anisotropic thermal expansion in the lateral direction. The TECs of the a and b axes were α_a = 7.6 × 10^?5 °C^?1 and α_b = 0.8 × 10^?5 °C^?1. The anisotropic thermal expansion behaviors in the lateral direction for I_β and III_I were closely related to the intermolecular hydrogen‐bonding systems. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1095–1102, 2002     

Maximizing the grain growth rate during the disorder‐to‐order transition in block copolymer melts

The factors controlling grain growth during the disorder‐to‐order transition in a polystyrene‐block‐polyisoprene copolymer melt were studied with time‐resolved depolarized light scattering. The ordered phase consisted of hexagonally packed polyisoprene cylinders, and the order–disorder‐transition temperature of the block copolymer (T_ODT) was 132 ± 1 °C. Our objective was to identify the temperature at which the grain growth rate was maximized (T_max) and compare it with theoretical predictions. We conducted seeded grain growth experiments, which comprised two steps. In the first step, which lasted for 43 min, the sample was cooled from the disordered state to 124 °C. This resulted in the formation of a small number of ordered grains or seeds. This was followed by a second step in which the sample was heated to temperatures between 124 and 132 °C and the seeds grew with time. Our objective was to study grain growth at different temperatures starting from the same initial condition. The value of T_max obtained experimentally was 128 °C. The theoretically predicted value of T_max, based entirely on the rheological properties of the disordered sample and T_ODT, was also 128 °C. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2231–2242, 2001