Production of “dichroitic” diffraction gratings in glasses containing silver nanoparticles via particle deformation with ultrashort laser pulses

By repetitive irradiation of pico- or femtosecond laser pulses on glasses containing silver nanoparticles, dichroitic areas can be produced with different optical properties depending on the actual irradiation parameters. This effect, which is nanoscopically caused by permanent deformation of the initially spherical particles to non-spherical shapes and an additional formation of a halo of very small particles, is studied as a function of polarization and number of the applied pulses using two different laser systems (Ti:sapphire, λ=400 nm, t_p=150 fs; Nd:YLF, λ=523.5 nm, t_p=4 ps). A very special diffraction grating produced by this local deformation, which has strongly polarization- and wavelength-dependent features, is introduced and discussed. Received: 20 July 2001 / Published online: 10 October 2001     

A novel method of nanocrystal fabrication based on laser ablation in liquid environment

Metal nanoparticles can be prepared by a novel technique that consists of the laser ablation of a solid target immersed in a water solution of a metal salt. Silicon was chosen as the most adequate target to synthesize silver and gold nanoparticles from a water solution of either AgNO₃ or HAuCl₄. The influence of both the silver nitrate concentrations and the irradiation time of the Si target on the optical properties of the Au and Ag nanoparticles have been investigated. The crystalline nature of the metal nanoparticles has been determined by X-ray diffraction (XRD). Average size and particle size distribution have been measured by means of TEM. The absorbance spectra show the characteristic band of the surface resonant plasmon of silver and gold nanoparticles.     

Ion synthesis of silver nanoparticles in viscous-fluid epoxy resin

A method is described for the ion synthesis of silver nanoparticles in epoxy resin that is in a viscousfluid state (viscosity 30 Pa s) during irradiation. The viscous-fluid or glassy polymer is implanted by 30-keV silver ions at a current density of 4 μA/cm² in the ion beam in the dose range 2.2 × 10¹⁶–7.5 × 10¹⁶ ions/cm². The epoxy layers thus synthesized contain silver nanoparticles, which are studied by transmission electron microscopy and optical absorption spectroscopy. The use of the viscous-fluid state increases the diffusion coefficient of the implanted impurity, which stimulates the nucleation and growth of nanoparticles at low implantation doses and allows a high factor of filling of the polymer with the metal to be achieved.     

Growth fusion of submicron spherical boron carbide particles by repetitive pulsed laser irradiation in liquid media

We studied the fabrication of B₄C submicron particles by laser irradiation of boron nanoparticles dispersed in an organic solvent. The spherical shape of the formed particles suggests that instantaneous melt formation and solidification by quenching are involved in the particle-forming process. B₄C particles gradually became larger with irradiation time at relatively low laser fluence (1.5 J cm⁻² pulse⁻¹) by repetitive melting and fusion of the particles, and the B₄C yield increased with irradiation time to 90% for 600 min of irradiation. At higher laser fluences, the B₄C yield decreased due to the explosive ablation of boron or B₄C to form H₃BO₃, and thus only the larger B₄C particles were observed. The dielectric constant of the organic solvent also affected the generated B₄C particle size, probably due to the degree of particle aggregation. Thus, this technique can provide a new approach for fabricating spherical submicron particles of ceramic materials, such as carbides, with simple and safe processes.     

Laser ablation of silver and gold in liquid ammonia

Laser ablation of a silver (Ag) and/or gold (Au) target was performed in liquid ammonia (l-NH₃) at 233 K using nanosecond laser pulses of 1064, 532 and 355 nm wavelengths. An “in situ” monitoring of the ablation process by UV/vis/NIR spectroscopy has shown the evolution of the surface plasmon extinction band of silver or gold nanoparticles and thus confirmed their formation. While sols of Au nanoparticles in l-NH₃ are quite stable in air, those of Ag nanoparticles undergo oxidation to Ag(I) complexes with NH₃ ligands. On the other hand, formation of solvated electrons, namely of the (e⁻)NH₃ solvates, has not been unequivocally confirmed under the conditions of our laser ablation/nanoparticle fragmentation experiment, since only very weak vis/NIR spectral features of these solvates were observed with a low reproducibility. Reference experiments have shown that the well-known chemical production of these solvates is hindered by the presence of Ag and Au plates. Ag and Au targets can thus possibly act as electron scavengers in our ablation experiments.     

Synthesis and optical properties of silver nanoparticles in ORMOCER

Experimental results on synthesis of metal nanoparticles in ORMOCER by ion implantation are presented. Silver ions were implanted into organic/inorganic matrix at an accelerating energy of 30?keV and doses in the range of 0.25?10¹⁷ to 0.75?10¹⁷?ion/cm². The silver ions form metal nanoparticles, which demonstrate surface plasmon absorption at the wavelength of 425?C580?nm. The nonlinear absorption of new composite materials is measured by Z-scan technique using 150?fs laser pulses at 780?nm wavelength. ORMOCER matrix shows two-photon nonlinear absorption, whereas ORMOCER with silver nanoparticles demonstrates saturated absorption. Some optical applications of these composite materials are discussed.     

Space-selective co-precipitation of silver and gold nanoparticles in femtosecond laser pulses irradiated Ag, Au co-doped silicate glass

We report on space-selective co-precipitation of silver and gold nanoparticles in Ag⁺, Au³⁺ co-doped silicate glasses by irradiation of femtosecond laser pulses and subsequent annealing at high temperatures. The color of the irradiated area in the glass sample changed from yellow to red with the increase of the annealing temperature. The effects of average laser power and annealing temperature on precipitation of the nanoparticles were investigated. A reasonable mechanism was proposed to explain the observed phenomena.     

Self-organization of thin metal films by irradiation with nanosecond laser pulses

Modifications in thin metal films under intensive laser irradiation were studied. Gold, silver, copper, chromium and aluminum films with the thickness of 100 nm were deposited on the glass substrate. Back-side irradiation through the substrate with a burst of nanosecond pulses tightly focused to a line was applied. The film removal threshold with a single pulse F_th was estimated for every material and laser fluence was kept above it in the range of 1.5-3 F_th during experiments. Diverse behavior of the films depending on the metal, the shift between pulses and laser fluence was observed. In chromium, the regular structures were developed in a quite wide range of processing parameters. In gold, three kinds of ripples were observed: transverse (similar to ripples in chromium), longitudinal and a structure of ripples oriented at 60° to each other. The combination of physical properties facilitated the regular assembly of the molten metal in chromium and to some extent in gold.     

Laser ablation of silver in different liquids: Optical and nonlinear optical properties of silver nanoparticles

The optical, structural, and nonlinear optical properties of silver nanoparticles prepared using the method of laser ablation in various liquids at wavelengths of 397, 532, and 795 nm with laser pulses of different duration are studied. An analysis of the dimensional and spectral characteristics of the silver nanoparticles revealed a time dynamics of the nanoparticle size distribution in solutions. It is shown that thermal self-defocusing is observed for the case of nanosecond or shorter pulses generated with a high repetition rate. For picosecond and femtosecond pulses with a low repetition rate, the effects of self-focusing (γ = 3 × 10^?13 cm² W^?1) and saturated absorption (β = ?1.5 × 10^?9 cm W^?1) were observed in the solutions under study. The third-order nonlinear susceptibility of the silver nanoparticles was found to be 5 × 10^?8 esu at a wavelength of 397 nm.     

The effect of the deposition parameters on size, distribution and antimicrobial properties of photoinduced silver nanoparticles on titania coatings

Controlled photodeposition of silver nanoparticles (AgNP) on titania coatings using two different sources of UV light is described. Titania (anatase) thin films were prepared by the sol-gel dip-coating method on silicon wafers. AgNPs were grown on the titania surface as a result of UV illumination of titania films immersed in aqueous solutions of silver nitrate. UV xenon lamp or excimer laser, both operating at the wavelength 351 ± 5 nm, was used as illumination sources. The AFM topography of AgNP/TiO₂ nanocomposites revealed that silver nanoparticles could be synthesized by both sources of illumination, however the photocatalysis carried out by UV light from xenon lamp illumination leads to larger AgNP than those synthesized using the laser beam. It was found that the increasing concentration of silver ions in the initial solution increases the number of Ag nanoparticles on the titania surface, while longer time of irradiation results the growth of larger size nanoparticles. Antibacterial tests performed on TiO₂ covered by Ag nanoparticles revealed that increasing density of nanoparticles enhances the inhibition of bacterial growth. It was also found that antibacterial activity drops by only 10-15% after 6 cycles compared to the initial use.     

Comparison of silver nanoparticles confined in nanoporous silica prepared by chemical synthesis and by ultra-short pulsed laser ablation in liquid

Hexagonally ordered mesoporous silica materials, MCM-41 and SBA-15, have been synthesized and loaded with Ag nanoparticles, utilizing both chemical synthesis and ultra-short pulsed laser ablation in liquid. In laser ablation, a silver target, immersed in aqueous suspension of ordered mesoporous silica SBA-15, was irradiated by ultra-short laser pulses to generate silver nanoparticles. For comparison, samples of similar silver contents were prepared either by incorporating silver into the SBA-15 during a hydrothermal synthesis or by introducing silver in MCM-41 by template ion-exchange. Samples were characterized by XRD, N₂ physisorption, TEM and UV–vis spectroscopy. All preparations contained significant amount of 5–50 nm size silver agglomerates on the outer surface of the silica particles. The laser ablation process did not cause significant destruction of the SBA-15 structure and metallic silver (Ag⁰) nanoparticles were mainly generated. It is demonstrated that by laser ablation in aqueous silica suspension smaller and more uniform metallic silver particles can be produced and loaded on the surface of the silica support than by synthesis procedures. Catalytic properties of the samples have been tested in the total oxidation of toluene. Because of its favorable Ag dispersity, the Ag/SBA-15 catalyst, generated by the laser ablation method, had better catalytic stability and, relative to its Ag load, higher activity than the conventional Ag/SBA-15 preparations.     

Proof‐of‐Concept Studies Directed toward the Formation of Metallic Ag Nanostructures from Ag3PO4 Induced by Electron Beam and Femtosecond Laser

In this work, for the first time, the instantaneous nucleation and growth processes of Ag nanoparticles on Ag₃PO₄ mediated by femtosecond laser pulses are reported and analyzed. The investigated samples are pure Ag₃PO₄ sample, electron‐irradiated Ag₃PO₄ sample, and laser‐irradiated sample. Complete characterization of the samples is performed using X‐ray diffraction (XRD), Rietveld refinements, field emission scanning electron microscopy, and energy dispersive spectroscopy (EDS). XRD confirms that the irradiated surface layer remains crystalline, and according to EDS analysis, the surface particles are composed primarily of Ag nanoparticles. This method not only offers a one‐step route to synthesize Ag nanoparticles using laser‐assisted irradiation with particle size control, but also reports a complex process involving the formation and subsequent growth of Ag nanoparticles through an unexpected additive‐free in situ fabrication process.     

Structural changes induced on strontium barium niobate glass by femtosecond laser irradiation

Localized modification of the optical properties of erbium doped strontium barium niobate (SBN) glass has been performed using femtosecond laser irradiation. The samples, with composition SrO–BaO–Nb₂O₅–B₂O₅ and doped with 5%mol of Er³⁺, were fabricated using a melt-quenching method. The samples were irradiated with different number of pulses per spot (1–50 pulses) at two different laser fluences (2.6 and 5.6 J/cm²) by using an fs laser amplifier operating at 800 nm and generating pulses with a duration of 120 fs. Micro-luminescent microscopy, using an Ar⁺ laser as excitation source, has been used to analyze the modifications of the luminescent properties of the sample upon fs laser exposure. The emissions of the Er³⁺: ⁴I_11/2→⁴I_15/2 and ⁴I_13/2→⁴I_15/2 transitions allow appreciating the structural modifications caused by femtosecond laser exposure. The lifetimes of the levels involved in these transitions were measured inside and outside the laser irradiated region. These measurements have been compared with those obtained in bulk glass ceramic sample, which is obtained from the glass precursor by a thermal treatment in order to estimate the optimal conditions to produce nanocrystals in a localized region by ultrafast laser irradiation.     

Methoxycarbonyl-terminated hyperbranched poly(amine-ester) as templates for synthesis of silver nanoparticles

Highly stable and spherical silver nanoparticles, stabilized by methoxycarbonyl-terminated hyperbranched poly(amine-ester) (HPAE-COOCH₃), were synthesized in water with reducing AgNO₃/HPAE-COOCH₃ using two methods, viz. NaBH₄ and ultraviolet irradiation. HPAE-COOCH₃ was found to play a key role in the formation of nanoparticles. UV–visible absorption, Transmission electron microscopic (TEM), and Fourier transform infrared spectroscopy (FT-IR) had been used to study the structure and characterization of the silver nanoparticles. The absorption peaks of the silver nanoparticles appear at ~420 nm in UV–visible absorption spectra; average particle size reduced by NaBH₄ is ~30 nm, which is ~10 and ~15 nm, respectively, when ultraviolet irradiation time is 12 and 24 h. FT-IR spectra confirm that there is strong interaction between silver nanoparticles and HPAE-COOCH₃. And silver nanoparticles/HPAE-COOCH₃ aqueous solution can keep stable for more than 3 months.     

Erratum to Formation and control of Au and Ag nanoparticles inside borate glasses using femtosecond laser and heat treatment

We report the spectroscopic properties of femtosecond laser-irradiated sodium-alumino-borate glass doped with silver and gold ions. We precipitated gold and silver nanoparticles by laser irradiation and annealing at 400°C for 30 min. The irradiation and annealing treatment produced different absorption and emission characteristics in Au³⁺ doped and Au³⁺, Ag⁺ codoped glasses, and the possible mechanisms of the observed results are discussed. The size of the nanoparticles was estimated by TEM and absorption band analysis.     

Ion synthesis and laser annealing of Cu nanoparticles in Al2O3

Al₂O₃ samples with Cu nanoparticles, synthesised by ion implantation at 40 keV with a dose of 1×10¹⁷ ion/cm² and a current density from 2.5 to 12.5 μA/cm², were annealed using ten pulses from a KrF excimer laser with a single pulse fluence of 0.3 J/cm². The copper depth distribution, formation and modification of metal nanoparticles under the ion implantation and laser treatment were studied by Rutherford backscattering (RBS), energy dispersive X-ray (EDX) analysis, atomic force microscopy (AFM) and optical spectroscopy. It was found that laser annealing leads to a reduction in the nanoparticle size without diffusion of metal atoms into the bulk. The change in particle size and the possibility for oxidation of the copper particles are examined in the framework of Mie theory. Calculations presented show that under excimer laser treatment, Cu nanoparticles are more likely to be reduced in size than to undergo oxidation. Received: 19 April 2001 / Accepted: 7 November 2001 / Published online: 23 January 2002     

Ion synthesis of copper nanoparticles in sapphire and their modification by high-power excimer laser pulses: A review

Composite layers made in sapphire by implantation of 40-keV Cu⁺ ions at a dose of 1 × 10¹⁷ cm⁻² and an ion beam current density varying from 2.5 to 10 μA/cm² are studied. It is shown that ion implantation makes it possible to synthesize a composite layer containing copper nanoparticles at the surface of the insulator. However, the nanoparticle size distribution in this layer is nonuniform. The composite layer is exposed to high-power excimer laser radiation with the aim of modifying the size and size distribution of the metal nanoparticles in it. The resulting structures are examined by Rutherford backscattering, optical reflection spectroscopy, and atomic force microscopy. It is found that the laser irradiation diminishes copper nanoparticles in the composite layer. Experimental data on laser modification may be explained by photofragmentation and/or melting of the nanoparticles in the sapphire matrix under the action of nanosecond laser pulses.     

Enhanced luminescence of silver nanoclusters in mesoporous film

Luminescence of silver nanoparticles photodeposited on titan dioxide nanoparticles of mesoporous film is studied. Luminescence was registered under the two-photon excitation by femtosecond laser pulses of Ti:sapphire laser. It occurs that Ag/TiO₂ mesoporous films have high concentration of bright luminescence spots which reveal stability to degradation under long illumination. Various configurations of silver nanoparticles are analyzed to explain the physics of bright luminescence spots (“hot spots”). Luminescence intensity reveals “hot spots” dependence on excitation laser pulse polarization. Properties of Ag/TiO₂ system show its promising usage for single molecule spectroscopy and biological objects visualization.     

Laser annealing of dielectrics with metal nanoparticles

The effect of nanosecond excimer laser pulses on a composite layer of sodium-calcium silicate glass with silver nanoparticles has been investigated. Nanoparticles were synthesized by ion implantation. Based on measuring the optical absorption and reflection spectra of the composite layers, it is found that an increase in the number of laser pulses leads to a monotonic decrease in the size of silver nanoparticles. However, laser irradiation with a longer duration leads to the growth of nanoparticles with their subsequent destruction. The effects observed are discussed in terms of heating a glass composite layer as a result of the effective absorption of laser radiation.     

The effect of concentration on the thermo-optical properties of colloidal silver nanoparticles

The thermo-optical properties of colloidal silver nanoparticles (AgNPs) are investigated under a low power laser irradiation at 532 nm. Colloidal AgNPs are synthesized by nanosecond pulsed laser ablation of a pure silver plate in distilled water. The morphology and size of the AgNPs are determined by transmission electron microscopy. Closed Z-scan measurements reveal that nonlocal thermo-optic process is responsible for the nonlinear refractive index of colloid containing different concentrations of silver nanoparticles. The Z-scan behavior of the nanoparticle samples has been investigated based on a nonlocal thermo-optic process and it is shown that the aberrant thermal lens model is in excellent agreement with the experimental results. Z-scan measurement fits have allowed the values of nonlinear refractive index (n₂) and thermo-optic coefficients (dn/dt) to be determined at different concentrations of silver nanoparticles. Large enhancement factors were measured for values of n₂ and dn/dt of the colloids at higher silver nanoparticle volume fraction. Our results suggest that nonlocal thermal nonlinear processes will play an important role in the development of photonic applications involving metal nanoparticle colloids.