循环伏安法研究利福平的电化学行为

采用循环伏安法研究了利福平在多壁碳纳米管修饰电极(MWCNT′s/GCE)上的电化学行为。结果表明:在pH 1.2的0.2mol.L-1硫酸-硫酸钠溶液中,修饰电极对利福平有良好的电催化作用,能够显著提高氧化还原峰电流,还原峰电流与利福平浓度分别在6.6×10-8～6.8×10-6 mol.L-1,6.8×10-6～4.8×10-5 mol.L-1范围内呈线性关系,检出限(3S/N)为3.0×10-8 mol.L-1。对利福平在修饰电极(MWCNT′s/GCE)上的电化学动力学性质进行了研究。     

β-丙氨酸-银复合膜修饰电极用于循环伏安法测定对乙酰氨基酚

制备了β-丙氨酸-银复合膜修饰电极(Ag-Ala/GCE),采用循环伏安法研究了对乙酰氨基酚在修饰电极上的电化学行为。结果表明:在pH 4.0的磷酸盐缓冲液中,对乙酰氨基酚在修饰电极上呈现一对灵敏的氧化还原峰,提出了用循环伏安法测定对乙酰氨基酚的含量。对乙酰氨基酚浓度在6.0×10-7～7.0×10-4 mol.L-1范围内与氧化峰电流呈现线性关系,检出限(3S/N)为2.0×10-7 mol.L-1。修饰电极用于药剂中对乙酰氨基酚的测定,并用标准加入法测得方法的回收率在95.1%～101.6%之间。     

聚拉莫三嗪修饰玻碳电极测定痕量铜(Ⅱ)的研究

在稀H2SO4介质中,采用循环伏安法制备了聚拉莫三嗪膜修饰玻碳电极(PLTG/GCE),将制得的膜修饰电极(PLTG/GCE)在一定电位下选择性预富集Cu(Ⅱ),并用差分脉冲溶出伏安法测定.结果表明,该膜修饰电极对Cu(Ⅱ)的富集作用明显强于裸玻碳电极.对电聚合条件、富集和溶出介质、富集时间及富集电位等实验参数进行了考察,在优化实验条件下,Cu(Ⅱ)的浓度在4.0×10-9～1.3×10-7mol· L-1范围内与溶出峰电流呈线性关系,相关系数为0.9999,检出限为1.5×10-9 mol·L-1.该修饰电极具有较高的灵敏度和选择性,用于实际水样的分析,平均回收率为98.7％.     

芦丁在纳米金修饰玻碳电极上的电化学行为及其测定

采用循环伏安法将纳米金电沉积于玻碳电极表面,制备了纳米金修饰玻碳电极(NG/GCE).在pH3.29的Britton-Robinson(B-R)缓冲溶液中,用循环伏安法研究了芦丁在NG/GCE上的电化学行为.结果表明,NG/GCE对芦丁的氧化还原反应有良好的电催化作用.用方波伏安法测得芦丁的还原峰电流与其浓度在2.0×10-8～2.0×10-6mol/L范围内呈线性关系,检出限为1.0×10-8mol/L(S/N=3).     

用银-色氨酸复合膜修饰玻碳电极循环伏安法测定去甲肾上腺素

在含有1.0mmol.L-1硝酸银、5.58×10-2 mol.L-1色氨酸的溶液中,于-0.8～1.8V(vs.Ag/AgCl)电位下,在玻碳电极表面电沉积一层银-色氨酸复合膜,制得银-色氨酸复合膜修饰玻碳电极(Ag-TRY/GCE)。采用扫描电镜对电极表面的性能进行表征,循环伏安法对其电化学性能进行研究。试验发现:在pH 6.0磷酸盐缓冲溶液中,去甲肾上腺素(NE)在修饰电极出现一对明显的氧化还原峰,氧化峰电位为0.306V,还原峰电位为0.368V,提出了用循环伏安法测定NE的方法。在试验条件下,氧化峰电流与去甲肾上腺素浓度在3.4×10-7～8.3×10-6 mol.L-1和8.3×10-6～1.1×10-4 mol.L-1两段范围内呈线性关系,检出限(3S/N)为4.3×10-8 mol.L-1。修饰电极用于药物中去甲肾上腺素的测定,加标回收率在95.6%～99.4%之间。     

多巴酚丁胺在聚对氨基吡啶化学修饰电极上的电化学行为及其吸附溶出伏安法测定

在玻碳电极(GCE)上制备了聚对氨基吡啶(POAP)修饰膜电极,并研究了多巴酚丁胺(DBTM)在POAP电极上的电化学行为。POAP修饰电极对DBTM的氧化有良好的电催化作用。循环伏安(CV)图上出现两个氧化峰(P1,P2)和一个还原峰(P3)。在最佳实验条件下,P1氧化峰电流与DBTM浓度在9.12×10-10～8.15×10-7mol L和3.19×10-6～3.40×10-5mol L范围内呈良好线性关系,开路富集5min检出限可达9.12×10-11mol L。     

纳米二氧化铈修饰碳糊电极线性扫描伏安法测定苯酚

在0.01mol.L-1硼砂溶液(pH 9.18)中,用纳米二氧化铈修饰碳糊电极作为工作电极,线性扫描伏安法测定苯酚。伏安图上出现一灵敏的氧化峰,其峰电位为+0.56V(vs.SCE),峰电流与苯酚的浓度在1.0×10-7～2.0×10-4 mol.L-1范围内呈线性关系,检出限(3s/k)为5.0×10-8 mol.L-1。富集时间为30s,同时采用线性扫描伏安法研究苯酚在纳米二氧化铈修饰碳糊电极上的氧化还原反应,结果表明此电极反应为一不可逆的吸附过程。     

乙炔黑修饰电极上吡虫啉的电化学行为及测定

制备了乙炔黑修饰电极(AB/GCE),并用循环伏安法(CV)研究了吡虫啉(IDP)在该修饰电极上的循环伏安行为。在pH 9.0的NH3.H2O-NH4Cl缓冲液中,IDP在该电极上出现一不可逆的还原峰。在20～240mV/s扫速范围内,其还原峰电流(Ipc)与扫速平方根(v1/2)呈线性关系,表明该电极过程受扩散控制。计算了电极过程的部分动力学参数:电极有效面积为0.0635cm2,转移电子数为2,扩散系数为3.793×10-3cm2/s。运用方波伏安法测定不同浓度IDP的方波伏安曲线,还原峰电流Ipc与IDP浓度在7.0×10-7～8.0×10-5mol/L范围内呈良好线性关系(r=0.9975),检出限为2.29×10-7mol/L,加标回收率为93.5%～105.3%。     

聚(三聚氰胺)与金纳米粒共修饰玻碳电极用于芦丁的电化学测定

通过电聚合和电沉积方法首次制得聚(三聚氰胺)和金纳米粒共修饰的电极(PMel/Au/GCE),并对修饰电极进行交流阻抗电化学分析。采用循环伏安法研究了芦丁在修饰电极上的电化学行为,发现其氧化峰电流和还原峰电流较裸玻碳电极(GCE)以及聚(三聚氰胺)修饰的电极(PMel/GCE)明显增强,提高了检测的灵敏度。对溶液的pH值、金纳米粒子电沉积时间、三聚氰胺电聚合时间和扫描速率等实验条件进行了优化。采用示差脉冲伏安法对芦丁进行定量分析,芦丁浓度分别在7.8×10-9~1.2×10-6mol/L和1.2×10-6~1.5×10-5mol/L范围内与峰电流呈线性,其相关系数(r2)分别为0.997和0.993,检出限(S/N=3)为5.5×10-9mol/L。将该电极用于市售芦丁片检测,回收率为96.4%~101.8%。     

银掺杂聚L-酪氨酸修饰电极的制备及对尿酸的测定

利用循环伏安法将银和L-酪氨酸聚合修饰在玻碳电极表面,制成银掺杂聚L-酪氨酸(Ag-PLT/GCE)修饰电极,研究了尿酸在该电极上的电化学行为,建立了循环伏安法测定尿酸的新方法。在pH=3.0的磷酸盐缓冲溶液中,扫描速率为100mV/s时,尿酸在该修饰电极上产生一氧化峰,Epa=0.637V(vs.Ag/AgCl)。用循环伏安法进行测定时,峰电流与尿酸浓度在8.0×10-7～1.0×10-5mol/L和1.0×10-5～1.0×10-4mol/L范围内呈良好的线性关系,检出限为3.0×10-7mol/L。方法用于尿样中尿酸的测定,结果满意。     

The Colloidal Stabilization of Carbon with Carbon: Carbon Nanobubbles as both Dispersant and Glue for Carbon Nanotubes

The superior physical properties of carbon nanotubes (CNTs) have led to their broad application. Intrinsically, CNTs tend to agglomerate from hydrophobic interactions, which is highly undesirable for solution processing and device fabrication. Commonly, a stabilizer consisting of organic surfactants or polymers is used to disperse CNTs. Recently, we synthesized nitrogen‐doped carbon hollow nanospheres (25–90 nm), termed carbon “nanobubbles”. They bear superior dispersability in water and distinctive graphitic order. Herein, we describe the nanobubble‐assisted dispersion of CNTs in aqueous solution upon sonication. This process relies on the π–π interaction between the two aromatic carbon nanostructures, which can process their carbon mixture in water into conductive filter membranes, ink, and discs. This stabilization can be extended to other aromatic carbons. In addition, the π–π interaction may create a new type of carbon p–n junction that can be used to improve charge separation.     

一维新型碳的同素异形体:碳链

碳链是一种完全一维的、具有电子轨道sp杂化结构的新型碳的同素异形体.正是由于碳链的独特的一维结构,使其拥有区别于富勒烯、石墨烯和碳纳米管的化学键,从而表现出更加优异的性能,如:理论预言碳链的机械强度是石墨烯的几倍;碳链的导热也类似于石墨烯和碳纳米管;碳链是具有直接带隙的半导体材料,且带隙的大小可以通过其长度来调控,其长...     

Adsorption of Carbon Dioxide on Activated Carbon

The adsorption of CO2 on a raw activated carbon A and three modified activated carbon samples B, C, and D at temperatures ranging from 303 to 333 K and the thermodynamics of adsorption have been investigated using a vacuum adsorption apparatus in order to obtain more information about the effect of CO2 on removal of organic sulfur-containing compounds in industrial gases. The active ingredients impregnated in the carbon samples show significant influence on the adsorption for CO2 and its volumes adsorbed on modified carbon samples B, C, and D are all larger than that on the raw carbon sample A. On the other hand, the physical parameters such as surface area, pore volume, and micropore volume of carbon samples show no influence on the adsorbed amount of CO2. The Dubinin-Radushkevich (D-R) equation was the best model for fitting the adsorption data on carbon samples A and B, while the Preundlich equation was the best fit for the adsorption on carbon samples C and D. The isosteric heats of adsorption on carbon samples A, B, C, and D derived from the adsorption isotherms using the Clapeyron equation decreased slightly increasing surface loading. The heat of adsorption lay between 10.5 and 28.4 kJ/mol, with the carbon sample D having the highest value at all surface coverages that were studied. The observed entropy change associated with the adsorption for the carbon samples A, B, and C (above the surface coverage of 7 ml/g) was lower than the theoretical value for mobile adsorption. However, it was higher than the theoretical value for mobile adsorption but lower than the theoretical value for localized adsorption for carbon sample D.     

Growth of Single-walled Carbon Nanotubes on Substrates Using Carbon Monoxide as Carbon Source

The growth of single-walled carbon nanotubes(SWCNTs) on substrates has attracted great interests because of the potential applications in various fields. Carbon monoxide(CO) was used as the carbon source for the growth of SWCNTs on silicon substrates. Random or oriented SWCNTs can be produced by varying the CO flow rate. When the flow rate of CO was as low as 20 sccm(sccm:standard cubic centimeter per minute), dense SWCNT networks with clean surface were produced. When the flow rate was above 50 sccm, vertically aligned SWCNT(VA-SWCNT) arrays were grown. Well-aligned VA-SWCNT arrays were obtained in the temperature range of 650-800℃ and the content of large-diameter(above 1.7 nm) tubes in the array increased with the temperature. The height of the array was affected by the growth temperature, the CO flow rate, and the growth time. These findings indicate CO can be used as an efficient carbon source for the growth of SWCNTs on substrates under low flow rates.     

埃洛石纳米管模板法一步法制备一维碳纳米管/碳纳米棒混合纳米碳材料

利用埃洛石纳米管(HNTs)特有的中空纳米结构,以及丰富的界面化学性质,以聚乙烯醇(PVA)为碳源,采用浸渍填充纳米孔方法实现了一步制备一维碳纳米管(CNTs)/碳纳米棒(CNRs)混合纳米碳材料。考察模板剂(HNTs)和碳源(PVA)之间的比例关系对混合纳米碳材料的结构影响,利用XRD、FTIR、Raman、N2吸附-脱附测试、TEM、SEM以及电阻率和分散性等表征手段分析混合纳米碳材料的结构变化。结果发现,PVA填充含量的增加将导致产物中CNRs的质量分数增加;当PVA和HNTs质量之比为1∶1时,所制备的CNTs/CNRs的孔体积达到最大值2.142 cm~3·g-1,比表面积达到583 m~2·g-1,并且表现出较好的电导率和分散性,表明低的PVA填充比例制备的混合碳材料中CNTs含量较高。     

二氧化碳与低碳经济发展

由于二氧化碳无色无味,又存在于大气中,因此它在植物生长中的重要性被人类忽略了。其实二氧化碳是光合作用的反应物,是植物生长的重要原料;又是一种新型绿色肥料。人类应该着力开发以二氧化碳为原料的新型肥料发展低碳经济。     

Ni/γ-Al2O3催化剂上CH4-CO2重整体系中积碳-消碳的研究

用动态热重技术和色谱技术联用以及XRD和TEM等表征手段,研究了Ni/γ-Al     

Carbon clusters

Some of the most significant discoveries and achievements concerning the mass spectra and gas phase ion chemistry of carbon clusters are reviewed. These include (1) nanosecond and femtosecond laser ionizations; (2) ion structures through ion/molecule reactions, ion chromatography, and computational methods; (3) carbon cluster cooling through radiative decay, dissociative decay, and thermionic emission; (4) mechanisms and energetics of fragmentation reactions; (5) endohedral fullerenes including recent data on ion beam implantation, and (6) ion chemistry as a function of the fullerene charge state.     

Palladium-Catalyzed Addition of Carbon Monoxide and Carbon Tetrachloride to 1-Octene in Supercritical Carbon Dioxide

The Pd-catalyzed addition of carbon monoxide and carbon tetrachloride to 1-octene gave coadduct [alkyl 2-( 2, 2, 2-trichloroethyl)octanoate] as the major product in supercritical carbon dioxide by using pyridine as the base. It was found that the selectivity and the yield of coadduct were greatly affected by the pressure of carbon dioxide, the reaction temperature and the amounts of alcohol and base used.     

碳纳米管含量对炭炭复合材料组织及力学性能的影响

炭纤维上原位合成了均匀生长且具有伸张形貌的碳纳米管,借助化学气相渗透制备了碳纳米管增强的炭炭复合材料,研究了不同含量的碳纳米管对炭炭复合材料组织和力学性能的影响。结果表明：炭纤维上生长碳纳米管改变了热解炭的沉积行为,诱导了各向同性热解炭的生成,且随着碳纳米管含量的增加,各向同性热解炭的厚度增加,但是复合材料的d002值却明显降低。微量的碳纳米管即可显著提高复合材料的力学强度,随着其含量的增加,复合材料的力学强度和模量迅速提高,但材料的断裂行为却急剧恶化,断裂模式由最初的假塑性断裂转变为脆性断裂。