Purification and Characterization of an Organic Solvent-Tolerant Lipase from <Emphasis Type="Italic">Pseudomonas aeruginosa</Emphasis> CS-2

An extracellular lipase secreted by Pseudomonas aeruginosa CS-2 was purified to homogeneity about 25.5-fold with an overall yield of 45.5%. The molecular mass of the lipase was estimated to be 33.9 kDa by SDS-PAGE and 36 kDa by gel filtration. The optimum temperature and pH were 50 °C and 8.0. The lipase was found to be stable at pH 4–10 and below 50 °C. Its hydrolytic activity was highest against p-nitrophenyl palmitate (p-NPP) among p-nitrophenyl esters of fatty acids with various chain lengths. The lipase was activated in the presence of Ca²⁺, while it was inactivated by other metal ions more or less. EDTA significantly reduced the lipase activity, indicating the lipase was a metalloenzyme. Gum Arabic and polyvinyl alcohol 124 enhanced lipase activity but Tween-20, Tween-80, and hexadecyltrimethyl ammonium bromide strongly inhibited the lipase. It exhibited stability in some organic solvents. The lipase was activated in the presence of acetonitrile. Conversely, it was drastically inactivated by methanol and ethanol.     

Characterization of Sol-gel bioencapsulates for ester hydrolysis and synthesis

Candida rugosa lipase was entrapped in silica sol-gel particles prepared by hydrolysis of methyltrimethoxysilane and assayed by p-nitrophenyl palmitate hydrolysis, as a function of pH and temperature, giving pH optima of 7.8 (free enzyme) and 5.0–8.0 (immobilized enzyme). The optimum temperature for the immobilized enzyme (50–55°C) was 19°C higher than for the free enzyme. Thermal, operational, and storage stability were determined with n-butanol and bytyric acid, giving at 45°C a half-life 2.7 times greater for the immobilized enzyme; storage time was 21 d at room temperature. For ester synthesis, the optimum temperature was 47°C, and high esterification conversions were obtained under repeated batch cycles (half-life of 138 h).     

Significantly Improved Expression and Biochemical Properties of Recombinant Serratia marcescens Lipase as Robust Biocatalyst for Kinetic Resolution of Chiral Ester

A lipase gene from Serratia marcescens ECU1010 was cloned into expression vector pET28a, sequenced, and overexpressed as an N terminus His-tag fusion protein in Escherichia coli. Through the optimization of culture conditions in shake flask, the lipase activity was improved up to 1.09 × 10⁵ U/l, which is a great improvement compared to our previous reports. It was purified to homogeneity by Ni-NTA affinity chromatography with an overall yield of 59.4% and a purification factor of 2.4-fold. This recombinant lipase displayed excellent stability below 30 °C and within the pH range of 5.0−6.8, giving temperature and pH optima at 40 °C and pH 9.0, respectively. The lipase activity was found to increase in the presence of metal ions such as Ca²⁺, Cu²⁺, and some nonionic surfactants such as PEG series. In addition, among p-nitrophenyl esters of fatty acids with varied chain length, the recombinant lipase showed the maximum activity on p-nitrophenyl laurate (C₁₂). Using racemic trans-3-(4′-methoxy-phenyl)-glycidyl methyl ester [(±)-MPGM] as substrate, which is a key chiral synthon for production of diltiazem, a 50% conversion yield was achieved after 4 h in toluene–water (100 mM KPB phosphate buffer, pH 7.5) biphasic system (5:5 ml) at 30 °C under shaking condition (160 rpm), affording (−)-MPGM in nearly 100% ee. The K _m and V _max values of the lipase for (±)-MPGM were 222 mM and 1.24 mmol min⁻¹ mg⁻¹, respectively. The above-mentioned features make the highly enantioselective lipase from Serratia marcescens ECU1010 a robust biocatalyst for practical use in large-scale production of diltiazem intermediate.     

Improving Stability and Activity of Cross-linked Enzyme Aggregates Based on Polyethylenimine in Hydrolysis of Fish Oil for Enrichment of Polyunsaturated Fatty Acids

Cross-linking of enzyme aggregates from recombinant Geotrichum sp. lipase based on polyethylenimine (PEI) was applied to hydrolyze fish oil for enrichment of polyunsaturated fatty acids successfully. Through acetone precipitation and cross-linking of physical aggregates using glutaraldehyde in the presence of PEI, firmly cross-linked enzyme aggregates (PEI-CLEAs) were prepared. They could maintain more than 65% of relative hydrolysis degree after incubation in the range of 50–55 °C for 4 h and maintain more than 85% of relative hydrolysis degree after being treated by acetone, tert-butyl alcohol and octane for 4 h. PEI-CLEAs increased hydrolysis degree to 42% from 12% by free lipase. After five batch reactions, PEI-CLEAs still maintained 72% of relative hydrolysis degree. Hydrolysis of fish oil by PEI-CLEAs produced glycerides containing concentrated EPA and DHA in good yield. PEI-CLEAs had advantages over general CLEAs and free lipase in initial reaction rate, hydrolysis degree, thermostability, organic solvent tolerance and reusability.     

Synthesis and colour properties of pigments based on terbium-dopped Mg<Subscript>2</Subscript>SnO<Subscript>4</Subscript>

The main aim of this work was to synthesize the magnesium orthostannate doped by terbium cations and tested whether these materials can be used for colouring of the different materials, e.g. organic binder and ceramic glazes. Initial composition of pigments was counted according the general formula 2MgO(1 − x)SnO₂–xTbO₂, where values of x varied from 0.1 to 0.5 in 0.1 steps. The simultaneous TG/DTA measurements of mixture containing tin oxide, magnesium carbonate hydroxide and terbium oxide showed that the formation of a new compound started at temperature 1,029 °C, but single-phase system was not prepared. Granulometric compositions of samples that were prepared by calcining at temperatures 1,300–1,400 °C are characterized by values of median (d ₅₀) in range 4–8 μm. The calcining temperature 1,500 °C caused the increase of the particle sizes at around 12 μm. The composition of sample 2MgO–1.5SnO₂–0.5TbO₂ and heating temperature 1,500 °C are the most suitable conditions for preparation of colourfully interesting pigment that can be recommended also for colouring of ceramic glazes. Especially, for colouring of decorative lead containing glaze G 07091 containing 5 wt% of PbO and 8 wt% of Al₂O₃.     

Synthesis of electrospun BaSrTiO<Subscript>3</Subscript>/PVP nanofibers

Ba_1−x Sr _x TiO₃(x = 0–0.5, BST) nanofibers with diameters of 150–210 nm were prepared by using electrospun BST/polyvinylpyrrolidone (PVP) composite fibers by calcination for 2 h at temperatures in the range of 650–800 °C in air. The morphology and crystal structure of calcined BST/PVP nanofibers were characterized as functions of calcination temperature and Sr content with an aid of XRD, FT-IR, and TEM. Although several unknown XRD peaks were detected when the fibers were calcined at temperatures less than 750 °C, they disappeared with increasing the temperature (above 750 °C) due to its thermal decomposition and complete reaction in the formation of BST. In addition, the FT-IR studies of BST/PVP fibers revealed that the intensities of the O–H stretching vibration bands (at 3430 and 1425 cm⁻¹) became weaker with increasing the calcination temperature and a broad band at 540 cm⁻¹, Ti–O vibration, appeared sharper and narrower after calcination above 750 °C due to the formation of metal oxide bonds. However, no effect of Sr content on the crystal structure of the composites was detected.     

Characterization of a Thermostable Family 1 Glycosyl Hydrolase Enzyme from <Emphasis Type="Italic">Putranjiva roxburghii</Emphasis> Seeds

A 66-kDa thermostable family 1 Glycosyl Hydrolase (GH1) enzyme with β-glucosidase and β-galactosidase activities was purified to homogeneity from the seeds of Putranjiva roxburghii belonging to Euphorbiaceae family. N-terminal and partial internal amino acid sequences showed significant resemblance to plant GH1 enzymes. Kinetic studies showed that enzyme hydrolyzed p-nitrophenyl β-d-glucopyranoside (pNP-Glc) with higher efficiency (K _cat/K _m = 2.27 × 10⁴ M⁻¹ s⁻¹) as compared to p-nitrophenyl β-d-galactopyranoside (pNP-Gal; K _cat/K _m = 1.15 × 10⁴ M⁻¹ s⁻¹). The optimum pH for β-galactosidase activity was 4.8 and 4.4 in citrate phosphate and acetate buffers respectively, while for β-glucosidase it was 4.6 in both buffers. The activation energy was found to be 10.6 kcal/mol in the temperature range 30–65 °C. The enzyme showed maximum activity at 65 °C with half life of ~40 min and first-order rate constant of 0.0172 min⁻¹. Far-UV CD spectra of enzyme exhibited α, β pattern at room temperature at pH 8.0. This thermostable enzyme with dual specificity and higher catalytic efficiency can be utilized for different commercial applications.     

Characterization of Smallest Active Monomeric Lipase from Novel <Emphasis Type="Italic">Rhizopus</Emphasis> Strain: Application in Transesterification

An extracellular lipase-producing fungus was isolated from oil-rich soil. This fungus belongs to the genus Rhizopus and clades with Rhizopus oryzae. Lipase was purified to homogeneity from this novel fungal source using ammonium sulphate precipitation followed by Q-Sepharose chromatography. The extracellular lipase was purified 8.6–fold, and enzymatic properties were studied. The molecular mass of the purified enzyme was estimated to be 17 kD by sodium dodecyl sulphate-polyacrylamide gel electrophoresis and 16.25 kD by matrix-assisted laser desorption ionization/time-of-flight analysis. The native molecular mass was estimated to be 17.5 kD by gel filtration, indicating the protein to be monomer. The optimum pH and temperature for the enzyme catalysis were 7.0 °C and 40 °C, respectively. Enzyme was stable in pH range 6.0–7.0 and retains 95–100% activity when incubated at 50 °C for 1 h. The pI of the purified lipase was 4.2. Enzyme was stable in the organic solvents such as ethanol, hexane and methanol for 2 h. Purified enzyme was used for transesterification of oleic acid in the presence of ethanol for production of oleic acid ethyl ester with a conversion efficiency of 66% after 24 h at 30 °C.     

XAFS investigation of [Pd(NH<Subscript>3</Subscript>)<Subscript>4</Subscript>][AuCl<Subscript>4</Subscript>]<Subscript>2</Subscript> and its thermolysis products

Thermolysis of double complex salt [Pd(NH₃)₄][AuCl₄]₂ has been studied in helium atmosphere from ambient to 350 °C. The XAFS of Pd K and Au L₃ edges and thermogravimetry measurements have been carried out to characterize the intermediates and the final product. In the temperature range 115–160 °C the complex is decomposed to form Pd(NH₃)₂Cl₂ and AuCl_4−x N _x species with x ranging from 2 to 3. Subsequent heating of the intermediate up to 300 °C leads to the total loss of NH₃. The Au–Cl and Au–Au bonds form the local environment of Au at the stage of decomposition while only four chlorine atoms are around Pd. At the temperature of 330 °C the Au and Pd nanoparticles as well as residues of palladium chloride are detected. The final product consists of separated Au and Pd nanoparticles.     

Study on thermal decomposition of copper(II) acetate monohydrate in air

The thermal decomposition of copper(II) acetate monohydrate (CuAc₂·H₂O) under 500 °C in air was studied by TG/DTG, DTA, in situ FTIR and XRD experiments. The experimental results showed that the thermal decomposition of CuAc₂·H₂O under 500 °C in air included three main steps. CuAc₂·H₂O was dehydrated under 168 °C; CuAc₂ decomposed to initial solid products and volatile products at 168–302 °C; the initial solid products Cu and Cu₂O were oxidized to CuO in air at 302–500 °C. The copper acetate peroxides were found to form between 100 and 150 °C, and the dehydration of these peroxides resulted in the presence of CuAc₂·H₂O above 168 °C. The initial solid products were found to be the admixture of Cu, Cu₂O, and CuO, not simply the single Cu₂O as reported before. Detailed reactions involved in these three steps were proposed to describe the complete mechanism and course of the thermal decomposition of CuAc₂·H₂O in air.     

Effect of heat treatment on electrochromic properties of TiO<Subscript>2</Subscript> thin films

Electrochromic titanium oxide (TiO₂) films were deposited on ITO/glass substrates by chemical solution deposition (CSD). The stock solutions were spin-coated onto substrates and then heated at various temperatures (200–500 °C) in various oxygen concentrations (0–80%) for 10 min. The effects of the processing parameters on the electrochromic properties of TiO₂ films were investigated. X-ray diffraction measurements demonstrated that the amorphous TiO₂ films were crystallized to form anatase films above 400 °C. The electrochromic properties and transmittance of TiO₂ films were measured in 1 M LiClO₄–propylene carbonate (PC) non-aqueous electrolyte. An amorphous 350 nm-thick TiO₂ film that was heated at 300°C in 60% ambient oxygen exhibited the maximum transmittance variation (ΔT%), 14.2%, between the bleached state and the colored state, with a ΔOD of 0.087, Q of 10.9 mC/cm², η of 7.98 cm²/C and x in Li _x ClO₄ of 0.076 at a wavelength (λ) of 550 nm.     

Volumetric Properties of Binary Mixtures of Glycerol + <Emphasis Type="Italic">tert</Emphasis>-Butanol over the Temperature Range 293.15 to 348.15 K at Atmospheric Pressure

Densities of glycerol (1) + tert-butanol (2) mixtures were measured over the temperature range 293.15 to 348.15 K at atmospheric pressure, over the entire composition range, with a vibrating tube densimeter. Excess molar volumes, apparent and partial molar volumes of glycerol and tert-butanol, thermal isobaric expansivities of the mixture and partial molar expansivities of the components were calculated. The excess molar volumes of the mixtures are negative at all temperatures, and deviations from ideality increase with increasing temperature. Excess molar volumes were fitted to the Redlich–Kister equation. Partial molar volumes of glycerol decrease with increasing tert-butanol concentration. The temperature dependence of the partial molar volumes of glycerol is characterized by an inversion at x ₂≈0.7. “Negative expansion” of the limiting partial volumes of glycerol was observed.     

Characterization of Thermo-stable Endoinulinase from a New Strain <Emphasis Type="Italic">Bacillus Smithii</Emphasis> T7

A new thermophilic inulinase-producing strain, which grows optimally at 60 °C, was isolated from soil samples with medium containing inulin as a sole carbon source. It was identified as a Bacillus smithii by analysis of 16s rDNA. Maximum inulinase yield of 135.2 IU/ml was achieved with medium pH7.0, containing inulin 2.0%, (NH₄)H₂PO₄ 0.5%, yeast extract 0.5%, at 50 °C 200 rpm shaker for 72-h incubation. The purified inulinase from the extracellular extract of B. smithii T7 shows endoinulinolytic activity. The optimum pH for this endoinulinase is 4.5 and stable at pH range of 4.0–8.0. The optimum temperature for enzyme activity was 70 °C, the half life of the endoinulinase is 9 h and 2.5 h at 70 °C and 80 °C respectively. Comparatively lower Michaelis–Menten constant (4.17 mM) and higher maximum reaction velocity (833 IU/mg protein) demonstrate the endoinulinase’s greater affinity for inulin substrate. These findings are significant for its potential industrial application.     

Molecular structure and conformation of triphenylsilane from gas-phase electron diffraction and theoretical calculations, and structural variations in H4?nSiPhn molecules (n?=?1–4)

The molecular structure of triphenylsilane has been investigated by gas-phase electron diffraction and theoretical calculations. The electron diffraction intensities from a previous study (Rozsondai B, Hargittai I, J Organomet Chem 334:269, 1987) have been reanalyzed using geometrical constraints and initial values of vibrational amplitudes from calculations. The free molecule has a chiral, propeller-like equilibrium conformation of C ₃ symmetry, with a twist angle of the phenyl groups τ = 39° ± 3°; the two enantiomeric conformers easily interconvert via three possible pathways. The low-frequency vibrational modes indicate that the three phenyl groups undergo large-amplitude torsional and out-of-plane bending vibrations about their respective Si–C bonds. Least-squares refinement of a model accounting for the bending vibrations gives the following bond distances and angles with estimated total errors: r _g(Si–C) = 1.874 ± 0.004 ?, 〈r _g(C–C)〉 = 1.402 ± 0.003 ?, 〈r _g(C–H)〉 = 1.102 ± 0.003 ?, and ∠_aC–Si–H = 108.6° ± 0.4°. Electron diffraction studies and MO calculations show that the lengths of the Si–C bonds in H_4−n SiPh _n molecules (n = 1–4) increase gradually with n, due to π → σ*(Si–C) delocalization. They also show that the mean lengths of the ring C–C bonds are about 0.003 ? larger than in unsubstituted benzene, due to a one hundredth angstrom lengthening of the C_ipso–C_ortho bonds caused by silicon substitution. A small increase of r(Si–H) and decrease of the ipso angle with increasing number of phenyl groups is also revealed by the calculations.     

Acyl iodides in organic synthesis: XIII. Reaction of acyl iodides with nitrogen-containing heteroaromatic compounds

Reactions of acetyl iodide with pyridine at room temperature and with quinoline both at 20–25°C and on cooling to −50°C involve dehydrohalogenation of acetyl iodide with formation of ketene and pyridinium or quinolinium iodides. The reaction of acetyl iodide with pyridine at −5 to −50°C led to the formation of N-acetylpyridinium iodide. Benzoyl iodide reacted with both pyridine and quinoline at both −50°C and at 20–25°C to form stable N-benzoylpyridinium and N-benzoylquinolinium iodides. The reaction of pyrrole with acetyl iodide under analogous conditions was accompanied by polymerization.     

Hydrogels of starch-g-(<Emphasis Type="Italic">tert</Emphasis>-butylacrylate) and starch-g-(<Emphasis Type="Italic">n</Emphasis>-butylacrylate) copolymers

The synthesis, characterization, and hydrogel properties of starch-g-(tert-butylacrylate) and starch-g-(n-butylacrylate) copolymers were studied. The optimum conditions for the grafting process of tert-butylacrylate into 1.0 g of starch were as follows: [tert-butylacrylate] = 0.04 mol/L, [CAN] = 9.0 × 10⁻⁴ mol/L, temperature = 20 °C in 100 mL solution, whereas the results using n-butylacrylate monomer were as follows: [n-butylacrylate] = 0.04 mol/L, [CAN] = 4.0 × 10⁻³ mol/L, temperature = 30 °C in 100 mL solution. The grafting evidences of monomers into starch were done through TG and its derivative DTG for thermal changes and mass losses, scanning electron microscope (SEM) for morphological changes, powder X-ray for crystallinity measurements and FTIR for functional group changes. Acid hydrolysis method was used efficiently to allow the calculations of the viscosity average molecular weight (M _v) of the grafted chains on starch and consequently the real percent of grafting efficiency (i.e. %GY). The capability of starch-g-(n-BAC) hydrogel to absorb water were found 10 times more than starch-g-(tert-BAC) hydrogel, which were clarified through the X-ray and SEM results.     

Structural evolution and magnetic properties of SrFe<Subscript>12</Subscript>O<Subscript>19</Subscript> nanofibers by electrospinning

The SrFe₁₂O₁₉/poly (vinyl pyrrolidone) (PVP) composite fiber precursors were prepared by the sol-gel assisted electrospinning with ferric nitrate, strontium nitrate and PVP as starting reagents. Subsequently, the M-type strontium ferrite (SrFe₁₂O₁₉) nanofibers were derived from calcination of these precursors at 750–1,000 °C.The composite precursors and strontium ferrite nanofibers were characterized by Fourier transform infrared spectroscopy, X-ray diffraction, scanning electron microscopy and vibrating sample magnetometer. The structural evolution process of strontium ferrite consists of the thermal decomposition and M-type strontium ferrite formation. After calcined at 750 °C for 2 h the single M-type strontium ferrite phase is formed by reactions of iron oxide and strontium oxide produced during the precursor decomposition process. The nanofiber morphology, diameter, crystallite size and grain morphology are mainly influenced by the calcination temperature and holding time. The SrFe₁₂O₁₉ nanofibers characterized with diameters of around 100 nm and a necklace-like structure obtained at 900 °C for 2 h, which is fabricated by nanosized particles about 60 nm with the plate-like morphology elongated in the preferred direction perpendicular to the c-axis, show the optimized magnetic property with saturation magnetization 59 A m² kg⁻¹ and coercivity 521 kA m⁻¹. It is found that the single domain critical size for these M-type strontium ferrite nanofibers is around 60 nm.     

Different coordination modes of the dimethyldisulfide ligand in trimethylplatinum(IV) complexes

The reaction of [PtMe₃(bpy)(Me₂CO)](BF₄) (2) (prepared from [PtMe₃I(bpy)] (1) plus Ag(BF₄)) with MeSSMe resulted in the formation of [PtMe₃(bpy)(MeSSMe-κS)](BF₄) (3). A single-crystal X-ray diffraction analysis revealed in the octahedral Pt(IV) complex (configuration index: OC-6-33), a conformation of the monodentately κS bound MeSSMe ligand (C–S–S–C 92.7(4)°) being very close to that in non-coordinated MeSSMe, thus allowing some hyperconjugative interaction stabilizing the S–S bond. The reaction of [K(18C6)][(PtMe₃)₂(μ-I)(μ-pz)₂] (4; 18C6 = 18-crown-6, Hpz = pyrazole) with Ag(BF₄) and MeSSMe resulted in the formation of dinuclear complexes [(PtMe₃)₂(μ-pz)₂(μ-MeSSMe)] existing at room temperature in acetone solution as different fast interconverting isomers. At –40 °C, two isomers with a μ-1κS:2κS (5a) and a μ-1κS:2κS′ (5b) coordinated MeSSMe ligand in the ratio 2:1 could be identified ¹H NMR spectroscopically. DFT calculations of type 5 complexes revealed the existence of two conformers with a μ-MeSSMe-1κS:2κS ligand, which differ mainly in the C–S–S–C dihedral angle (66.4 vs. 180.0° 6a/6a′). They have essentially the same energy and a very low activation barrier in acetone as solvent (1.3 kcal/mol) for their mutual interconversion. A further equilibrium structure was identified to be an isomer having a μ-MeSSMe-1κS:2κS′ ligand (6b) that proved to be only 1.9 kcal/mol higher in energy than 6a/6a′.     

Purification and Biochemical Characterization of a Highly Thermostable Xylanase from <Emphasis Type="Italic">Actinomadura</Emphasis> sp. Strain Cpt20 Isolated from Poultry Compost

An extracellular thermostable xylanase from a newly isolated thermophilic Actinomadura sp. strain Cpt20 was purified and characterized. Based on matrix-assisted laser desorption–ionization time-of-flight mass spectrometry analysis, the purified enzyme is a monomer with a molecular mass of 20,110.13 Da. The 19 residue N-terminal sequence of the enzyme showed 84% homology with those of actinomycete endoxylanases. The optimum pH and temperature values for xylanase activity were pH 10 and 80 °C, respectively. This xylanase was stable within a pH range of 5–10 and up to a temperature of 90 °C. It showed high thermostability at 60 °C for 5 days and half-life times at 90 °C and 100 °C were 2 and 1 h, respectively. The xylanase was specific for xylans, showing higher specific activity on soluble oat-spelt xylan followed by beechwood xylan. This enzyme obeyed the Michaelis–Menten kinetics, with the K _m and k _cat values being 1.55 mg soluble oat-spelt xylan/ml and 388 min⁻¹, respectively. While the xylanase from Actinomadura sp. Cpt20 was activated by Mn²⁺, Ca²⁺, and Cu²⁺, it was, strongly inhibited by Hg²⁺, Zn²⁺, and Ba²⁺. These properties make this enzyme a potential candidate for future use in biotechnological applications particularly in the pulp and paper industry.     

Low-temperature NO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript> Selective Reduction by Hydrocarbons on H-Mordenite Catalysts in Dielectric Barrier Discharge Plasma

Toward achieving selective catalytic reduction of NO _x by hydrocarbons at low temperatures (especially lower than 200 °C), C₂H₂ selective reduction of NO _x was explored on H-mordenite (H-MOR) catalysts in dielectric barrier discharge (DBD) plasma. This work reported significant synergistic effects of DBD plasmas and H-MOR catalysts for C₂H₂ selective reduction of NO _x at low temperatures (100–200 °C ) and across a wide range of O₂ content (0–15%). At 100 °C, NO _x conversions were 3.3, 11.6 and 66.7% for the plasma alone, catalyst alone and in-plasma catalysis (IPC) cases (with a reactant gas mixture of 500 ppm NO, 500 ppm C₂H₂, 10% O₂ in N₂, GHSV = 12,000 h⁻¹ and input energy density of 125 J L ⁻¹), respectively. At 200 °C, NO _x conversions were 3.8, 54.0 and 91.4% for the above three cases, respectively. Also, strong signals of hydrogen cyanide (HCN) byproduct were observed in the catalyst alone system by an on-line mass spectrometer. By contrast, almost no HCN was detected in the IPC system.