Electrodeposited polyaniline as a fiber coating for solid-phase microextraction of organochlorine pesticides from water

The study on the performance of polyaniline as a fiber coating for solid-phase microextraction (SPME) purposes has been reported. Polyaniline coatings were directly electrodeposited on the surface of a stainless steel wire and applied for the extraction of some organochlorine pesticides (OCPs) from water samples. Analyses were performed using GC-electron capture detection (GC-ECD). The results obtained show that polyaniline fiber coating is suitable for the successful extraction of organochlorine compounds. This behavior is most probably due to the porous surface structure of polyaniline film, which provides large surface areas and allowed for high extraction efficiency. Experimental parameters such as adsorption and desorption conditions were studied and optimized. The optimized method has an acceptable linearity, with a concentration range of 1-5000 ng/L. Single fiber repeatability and fiber-to-fiber reproducibility were less than 12 and 17%, respectively. High environmental resistance and lower cost are among the advantages of polyaniline fibers over commercially available SPME fibers. The developed method was applied to the analysis of real water samples from Yangtse River and Tianmu Lake.     

Preparation of a polyacrylonitrile/multi-walled carbon nanotubes composite by surface-initiated atom transfer radical polymerization on a stainless steel wire for solid-phase microextraction

We report on the fabrication and performances of a solid-phase microextraction (SPME) fiber based on a stainless steel wire coated with a covalently attached polyacrylonitrile (PAN)/multi-walled carbon nanotubes (MWCNTs) composite. This new coating is obtained by atom transfer radical polymerization (ATRP) of acrylonitrile mixed with MWCNTs. ATRP is initiated from 11-(2-bromo-2-methylpropionyloxy)-undecyl-phosphonic acid molecules grafted on the wire surface via the phosphonic acid group. The extraction performances of the fibers are assessed on different classes of compounds (polar, non-polar, aromatic, etc.) from water solutions by headspace extraction. The optimization of the parameters affecting the extraction efficiency of the target compounds was studied as well as the reproducibility and the repeatability of the fiber. The fibers sustain more than 200 extractions during which they remain chemically stable and maintain good performances (detection limits lower than 2 μg/l, repeatability, etc.). Considering their robustness together with their easy and inexpensive fabrication, these fibers could constitute promising alternatives to existing products.     

Ultrafine grain formation and coating mechanism arising from a blast coating process: A transmission electron microscopy analysis

This article examines the substrate/coating interface of a coating deposited onto mild steel and stainless steel substrates using an ambient temperature blast coating technique known as CoBlast. The process uses a coincident stream of an abrasive blast medium and coating medium particles to modify the substrate surface. The hypothesis for the high bond strength is that the abrasive medium roughens the surface while simultaneously disrupting the passivating oxide layer of the substrate, thereby exposing the reactive metal that then reacts with the coating medium. The aim of this study is to provide greater insight into the coating/substrate bonding mechanism by analysing the interface between a hydroxyapatite coating on both mild and stainless steel substrates. The coating adhesion was measured via a tensile test, and bond strengths of approximately 45 MPa were measured. The substrate/coating interface was examined using transmission electron microscopy and selected area diffraction. The analysis of the substrate/coating interface revealed the presence of ultrafine grains in both the coating and substrate at interface associated with deformation at the interface caused by particle impaction during deposition. The chemical reactivity resulting from the creation of these ultrafine grains is proposed to explain the high adhesive strength of CoBlast coatings.     

Preparation and characterization of porous carbon material-coated solid-phase microextraction metal fibers

Two kinds of porous carbon materials, including carbon aerogels (CAs), wormhole-like mesoporous carbons (WMCs), were synthesized and used as the coatings of solid-phase microextraction (SPME) fibers. By using stainless steel wire as the supporting core, six types of fibers were prepared with sol-gel method, direct coating method and direct coating plus sol-gel method. Headspace SPME experiments indicated that the extraction efficiencies of the CA fibers are better than those of the WMC fibers, although the surface area of WMCs is much higher than that of CAs. The sol-gel-CA fiber (CA-A) exhibited excellent extraction properties for non-polar compounds (BTEX, benzene, toluene, ethylbenzene, o-xylene), while direct-coated CA fiber (CA-B) presented the best performance in extracting polar compounds (phenols). The two CA fibers showed wide linear ranges, low detection limits (0.008-0.047μgL(-1) for BTEX, 0.15-5.7μgL(-1) for phenols) and good repeatabilities (RSDs less than 4.6% for BTEX, and less than 9.5% for phenols) and satisfying reproducibilities between fibers (RSDs less than 5.2% for BTEX, and less than 9.9% for phenols). These fibers were successfully used for the analysis of water samples from the Pearl River, which demonstrated the applicability of the home-made CA fibers.     

Facile fabrication of novel cobalt-based carbonaceous coatings on nickel-titanium alloy fiber substrate for selective solid-phase microextraction

Fabrication of selective adsorption coatings plays a crucial role in solid-phase microextraction(SPME).Herein, new strategies were developed for the in-situ fabrication of novel cobalt-based carbonaceous coatings on the nickel-titanium alloy(Ni Ti) fiber substrate using ZIF-67 as a precursor and template through the chemical reaction of ZIF-67 with glucose, dopamine(DA) and melamine, respectively. The adsorption performance of the resulting coatings was evaluated using representative aromatic co...     

Electrophoretic Deposition of Hydroxyapatite Coatings on Metal Substrates: A Nanoparticulate Dual-Coating Approach

Hydroxyapatite coatings can be readily deposited on metal substrates by electrophoretic deposition. However, subsequent sintering is highly problematic owing to the fact that temperatures in excess of 1100°C are required for commercial hydroxyapatite powders to achieve high density. Such temperatures damage the metal and induce metal-catalysed decomposition of the hydroxyapatite. Furthermore, the firing shrinkage of the hydroxyapatite coating on a constraining metal substrate leads to severe cracking. The present study has overcome these problems using a novel approach: the use of aged nanoparticulate hydroxyapatite sols (lower sintering temperature) and a dual coating strategy that overcomes the cracking problem. Dual layers of uncalcined hydroxyapatite (HAp) powder were electrophoretically coated on Ti, Ti6Al4V and 316L stainless steel metal substrates, sintered at 875–1000°C, and characterised by SEM and XRD, and interfacial shear strength measurement. Dual coatings on stainless steel had an average high bond strength (about 23 MPa), and dual coatings on titanium and titanium alloy had moderate strengths (about 14 and 11 MPa, respectively), in comparison with the measured shear strength of bone (35 MPa). SEM and XRD demonstrated that the second layer blended seamlessly with the first and filled the cracks in the first. The superior result on stainless steel is attributed to a more appropriate thermal expansion match with hydroxyapatite, the thinner oxide layer, or a combination of these factors.     

Are metal-organic frameworks able to provide a new generation of solid-phase microextraction coatings? – A review

Solid-phase microextraction (SPME) is a powerful technique commonly used in sample preparation for extraction/preconcentration of analytes from a wide variety of samples. Among the trends in improving SPME applications, current investigations are focused on the development of novel coatings able to improve the extraction efficiency, sensitivity, and thermal and mechanical stability, within other properties, of current commercial SPME fibers. Metal-organic frameworks (MOFs) merit to be highlighted as promising sorbent materials in SPME schemes. MOFs are porous hybrid materials composed by metal ions and organic linkers, presenting the highest surface areas known, with ease synthesis and high tuneability, together with adequate chemical and thermal stability. For MOF based-SPME fibers, it results important to pretreat adequately the SPME supports to ensure the correct formation of the MOF onto the fiber or the attachment MOF-support. This, in turn, will increase the final stability of the fiber while generating uniform coatings. This review provides a critical overview of the current state of the use of MOFs as SPME coatings, not only highlighting the advantages of these materials versus commercial SPME coatings in terms of stability, selectivity, and sensitivity; but also insightfully describing the current methods to obtain reproducible MOF-based SPME coatings.     

石墨烯层层键合固相微萃取纤维的制备及对多环芳烃的检测

通过3-巯基丙基三甲氧基硅烷处理银层包裹的不锈钢纤维,得到Si-OH功能化的纤维,氧化石墨烯被层层键合到Si-OH功能化的纤维上,还原氧化石墨烯得到石墨烯层层键合的固相微萃取纤维。该方法制备的新型石墨烯层层键合的固相微萃取纤维具有制备简单,机械性能强,萃取涂层牢固,萃取能力强等优势。建立具有较宽线性范围(5~200μg/L)、较低检测限(0.007~0.09μg/L)的固相微萃取-气相色谱分析方法,用该方法测定河水和雨水中多环芳烃的含量。所制备的新型纤维重现性好、稳定性高、萃取能力强,可实现对多环芳烃的痕量检测。     

固相微萃取中高分子涂层的研究

聚甲基乙烯基硅氧烷首次被用作固相微萃取（ＳＰＭＥ）装置的固相涂层,通过顶空固相微萃取气相色谱分析（ＨＳ－ＳＰＭＥ－ＧＣ）对使用聚甲基乙烯基硅氧烷固相涂层的ＳＰＭＥ装置进行了评价。对其使用厚度、温度及选择性进行了较深入的研究,找到了它的最佳使用条件和适用范围,并与商品化的ＳＰＭＥ涂层作了比较。对ＨＳ－ＳＰＭＥ－ＧＣ和ＨＳ－ＧＣ两种方法也作了比较,指出两者的适用范围不同。     

Preparation and Characterization of Metolachlor Molecularly Imprinted Polymer Coating on Stainless Steel Fibers for Solid-Phase Microextraction

A molecularly imprinted polymer (MIP) with metolachlor as the template molecule was first coated on the surface of stainless steel fibers through chemical bonding. Despite 12 times repeated coating procedures, a homogenous, porous, and highly cross-linked MIP coating was obtained with thickness of 17.4 µm (RSD of 6.1%). The specific selectivity of MIP coating to metolachlor and three metabolites could be concluded with 4.4, 4.1, 3.9, and 2.9 times higher extraction amounts of metolachlor, hydroxymetolachlor, deschlorometolachlor, and desmethylmetolachlor than that of the NIP coating, respectively, and good extraction capabilities for chloroacetanilide herbicides were found with the MIP-coated SPME stainless steel fiber. For validation, the fiber was applied for the extraction of metolachlor, propisochlor, and butachlor in spiked corn and soybean samples, and the recoveries of 90.7–92.6%, 86.4–87.9, and 85.4–87.5% were obtained, respectively.     

A novel strategy to increase performance of solid‐phase microextraction fibers: Electrodeposition of sol‐gel films on highly porous substrate

In the present work, the effect of substrate porosity for preparation of solid‐phase microextraction (SPME) fibers was investigated. The fibers were prepared by electrodeposition of sol‐gel coatings using negative potentials on porous Cu wire and compared with previous reported technique for preparation of SPME fibers using positive potentials on smooth gold wire. Porous substrate was prepared by electrodeposition of a thin layer of Cu on a Cu wire. The extraction capability of prepared fibers was evaluated through extraction of some aromatic hydrocarbons from the headspace of aqueous samples. The effect of substrate porosity and some operating parameters on extraction efficiency was optimized. The results showed that extraction efficiency of SPME fibers highly depends on porosity of the substrate. The LOD ranged from 0.005 to 0.010 ng/mL and repeatability at the 1 ng/mL was below 12%. Electrodeposited films were characterized for their surface morphology and thermal stability using SEM and thermogravimetric analysis, respectively. SEM analysis revealed formation of porous substrate and subsequently porous coating on the wire surface and thermogravimetric analysis showed high thermal stability of the prepared fiber.     

Multiwalled Carbon Nanotube Coated on Stainless Steel Wire for Solid-Phase Microextraction of Organochlorine Pesticides in Water

A novel solid-phase microextraction (SPME) fiber was prepared by coating multiwalled carbon nanotube (MWCNTs) on a stainless steel wire, and its characteristics were studied. To evaluate the MWCNTs coating, the fiber was used for the extraction of some organochlorine pesticides (OCPs) from water samples by Headspace SPME (HS-SPME) mode. Potential factors affecting the extraction efficiency such as extraction time, extraction temperature, agitation, ionic strength, desorption temperature, and time were also optimized. Several experiments were carried out by water spiked with target compounds to evaluate the analytical characteristics of the proposed method under optimized conditions. The linearity was from 0.1 to 10 ug/L with the linear correlation coefficients (r) ranging from 0.9956 to 0.9995. The limits of detection (LOD, S/N = 3) for these pesticides were between 0.43 and 2.13 ng/L and the precision (RSD, n = 5) was 2.53–12.25%. When this method was applied for the spiked real river sample, the relative recoveries ranged from 72.4% to 134.7% for the tested OCPs.     

In vitro evaluation of new biocompatible coatings for solid-phase microextraction: Implications for drug analysis and in vivo sampling applications

A new line of solid-phase microextraction (SPME) coatings suitable for use with liquid chromatography applications was recently developed to address the limitations of the currently available coatings. The proposed coatings were immobilized on the metal fiber core and consisted of a mixture of proprietary biocompatible binder and various types of coated silica (octadecyl, polar embedded and cyano) particles. The aim of this research was to perform in vitro assessment of these new SPME fibers in order to evaluate their suitability for drug analysis and in vivo SPME applications. The main parameters examined were extraction efficiency, solvent resistance, preconditioning, dependence of extraction kinetics on coating thickness, carryover, linear range and inter-fiber reproducibility. The performance of the proposed coatings was compared against commercial Carbowax-TPR (CW-TPR) coating, when applicable. The fibers were evaluated for the extraction of drugs of different classes (carbamazepine, propranolol, pseudoephedrine, ranitidine and diazepam) from plasma and urine. The analyses were performed using liquid chromatography-tandem mass spectrometry. The results show that the fibers perform very well for the extraction of biological fluids with no sample pre-treatment required and can also be used for in vivo sampling applications of flowing blood. A coating thickness of 45 μm was found to be a good compromise between extraction capacity and extraction kinetics. Due to the high extraction efficiency of these coatings, pre-equilibrium SPME with very short extraction times (2 min) can be employed to increase sample throughput. Inter-fiber reproducibility was ≤11% R.S.D. (n = 10) for model drugs examined in plasma, which is a significant improvement over polypyrrole coatings reported in literature, and permits single fiber use for in vivo applications.     

Hydroxyfullerene as a novel coating for solid-phase microextraction fiber with sol-gel technology

Hydroxyfullerene (fullerol) as a novel coating for solid-phase microextraction (SPME) fiber was first prepared by a sol-gel technology. The coating procedure involving sol solution composition and conditioning process was presented. A fullerene polysiloxane surface-bonded porous coating on the fused-silica fiber surface was obtained and confirmed by IR spectra and scanning electron microscopy. The coating has stable performance at high temperature (even to 360 degrees C) and solvents (organic and inorganic) because of the properties of fullerene and the chemical binding between the coating and the fiber surface. The extraction properties of the new coatings to less volatile organic compounds, such as polychlorinated biphenyls (PCBs), polycyclic aromatic hydrocarbons and polar aromatic amines were investigated using headspace SPME coupled with GC-electron-capture detection and GC-flame ionization detection. In addition, compared with commercial SPME stationary phases, the new coatings showed higher sensitivity, faster velocities of mass transfer for aromatic compound, and possessed planarity molecular recognition for PCBs. Moreover, this fiber was firm, inexpensive, durable and can be prepared simply. The fiber-to-fiber reproducibility was very good.     

Development of relatively selective, chemically and mechanically robust solid-phase microextraction fibers based on methacrylic acid-trimethylolpropanetrimethacrylate co-polymers

A versatile, relatively selective, chemically and mechanically robust solid-phase microextraction (SPME) fiber based on methacrylic acid-trimethylolpropanetrimethacrylate (MAA/TRIM) co-polymers was developed in a simple way and directly coupled with gas chromatography. Thus, using a glass capillary as a "mold", MAA/TRIM co-polymers were immobilized on a stainless steel wire base as a novel coating for SPME. The extraction performance of the MAA/TRIM-coated fiber was evaluated in detail using four triazines as model compounds, and several typical and important species of chemical compounds including opioids, xanthic alkaloids and phenoxyacetic acid herbicides were selected as additional examples to further illustrate the extraction mechanism and applicability of the fiber. The fiber showed high extraction efficiency for highly functionalized molecules (typically containing multiple amino, hydroxy, carbonyl and carboxy groups) via a hydrogen-bonding extraction mechanism. The maximum extraction ability and selectivity of the fiber could be obtained only in non-polar (aprotic) organic solvents, which are effective for the hydrogen-bonding interaction. The inherent chemical stability of MAA/TRIM co-polymers and the mechanical strength of the stainless steel wire as the fiber support made the MAA/TRIM-coated fiber highly durable in practical use.     

Nafion/活性炭涂层固相微萃取探头的制备与应用研究

采用Nafion和活性炭粉末作为固相涂层在不锈钢丝上交替涂制了固相微萃取探头(SPME),研究了它的特性,并与商品类似探头和单纯的Nafion探头作了比较。该探头可比商品探头(SPME)的富集率高1个数量级。由于Nafion有很强的极性,因此它对极性化合物有很强的萃取能力,适合萃取醇等物质。用该探头测定了醇类、酯类物质,检出限低于10ng/mL,相对标准偏差RSD<6 3%。     

Determination of parabens in cosmetic products by solid-phase microextraction of poly(ethylene glycol) diacrylate thin film on fibers and ultra high-speed liquid chromatography with diode array detector

The fabrication of a solid-phase microextraction (SPME) fiber through UV-induced polymerization of poly(ethylene glycol) diacrylate (PEG-DA) for determination of parabens in cosmetic products is presented in this work. The PEG-DA polymer coating was covalently attached to the fiber by introducing a surface modification with 3-(trichlorosilyl)propyl methacrylate (TPM). The PEG-DA polymer thin film coated on the fiber was homogeneous and wrinkled, which led to an increase of the surface area and high extraction efficiency. The extraction performances of the prepared SPME fibers were assessed by preconcentration of parabens including methylparaben, ethylparaben, propylparaben and benzylparaben from cosmetic products. The analysis was performed on an ultra high-speed liquid chromatography with diode array detector. The prepared SPME fibers exhibited good repeatability (for one fiber) and reproducibility (fiber-to-fiber) with RSDs of 5.4 and 6.9%, respectively. The optimized SPME method supported a wide linear range of 0.50-160 μg/mL and the detection limits for parabens were in the range of 0.12-0.15 μg/mL (S/N=3). The developed method was successfully applied for determination of parabens in cosmetic products with different natures.     

A highly thermal-resistant electrospun-based polyetherimide nanofibers coating for solid-phase microextraction

A high-temperature-resistant solid-phase microextraction (SPME) fiber was prepared based on polyetherimide (PEI) by the electrospinning method. The PEI polymeric solution was converted to nanofibers using high voltages and directly coated on a stainless steel SPME needle. The scanning electron microscopy images of PEI coating showed fibers with diameter range of 500–650 nm with a homogeneous and smooth surface morphology. The SPME nanofibers coating was optimized for PEI percentage, electrospinning voltage, and time. The extraction efficiency of the coating was investigated for headspace SPME of some environmentally important polycyclic aromatic hydrocarbons from aqueous samples followed by gas chromatography–mass spectrometry measurement. In addition, the important extraction parameters including extraction temperature, extraction time, ionic strength, as well as desorption temperature and time were investigated and optimized. The detection limits of the method under optimized conditions ranged from 1 to 5 ng L^?1 using time-scheduled selected ion monitoring mode. The relative standard deviations of the method were between 1.1 and 7.1 %, at a concentration level of 500 ng L^?1. The calibration curves of polycyclic aromatic hydrocarbons showed linearity in the range of 5–1000 ng L^?1. The developed method was successfully applied to real water samples and the relative recovery percentages obtained from the spiked water samples were from 84 to 98 % for all the selected analytes except for acenaphthene which was from 75 to 106 %.     

Atmosphere effects in the processing of silicon carbide and silicon oxycarbide thin films and coatings

Silicon carbide and silicon oxycarbide films were prepared from solutions of polycarbosilane and methyldimethoxysilane + tetraethoxysilane, respectively, and deposited on different substrates (Si wafers, stainless steel plates, sapphire and SiC fibers). The coatings were heated at different temperatures and in different atmospheres, such as regular grade argon, ultra high purity and argon vacuum. The films were characterized using different techniques (FT-IR, XRD, SIMS, Ellipsometry).The influence of the processing parameters (heat treatment temperature and atmosphere) on the final microstructure of the coatings is discussed in this article.     

Substrate-independent dip-pen nanolithography based on reactive coatings

We report that nanostructuring via dip-pen nanolithography can be used for modification of a broad range of different substrates (polystyrene, Teflon, stainless steel, glass, silicon, rubber, etc.) without the need for reconfiguring the underlying printing technology. This is made possible through the use of vapor-based coatings that can be deposited on these substrates with excellent conformity, while providing functional groups for subsequent spatially directed click chemistry via dip-pen nanolithography. Pattern quality has been compared on six different substrates demonstrating that this approach indeed results in a surface modification protocol with potential use for a wide range of biotechnological applications.