Alkoxy substituted benzodithiophene-alt-fluorobenzotriazole copolymer as donor in non-fullerene polymer solar cells

A new benzodithiophene(BDT)-alt-fluorobenzotriazole(FBTA) D-A copolymer J40 was designed and synthesized by introducing 2-octyldodecyloxy side chains on its BDT units, for expanding the family of the BDT- alt-FBTA-based copolymers and investigating the side chain effect on the photovoltaic performance of the polymer in non-fullerene polymer solar cells(PSCs).J40 exhibits complementary absorption spectra and matched electronic energy levels with the n-type organic semiconductor(n-OS)(3,9-bis(2-methylene-(3-(1,1-dicyanomethylene)-indanone))-5,5,11,11-tetrakis(4-hexylphenyl)-dithieno[2,3-d:2′,3′-d′]-sindaceno[1,2-b:5,6-b′]dithiophene)(ITIC) acceptor, and was used as polymer donor in the non-fullerene PSCs with ITIC as acceptor. The power conversion efficiency(PCE) of the PSCs based on J40:ITIC(1:1, w/w) with thermal annealing at 120 °C for 10 min reached 6.48% with a higher open-circuit voltage(Voc) of 0.89 V. The high Voc of the PSCs is benefitted from the lower-lying highest occupied molecular orbital(HOMO) energy level of J40. Although the photovoltaic performance of the polymer J40 with alkoxy side chain is lower than that of J60 and J61 with alkylthio-thienyl conjugated side chains, the PCE of6.48% for the J40-based device is still a relatively higher photovoltaic efficiency in the non-fullerene PSCs reported so far. The results indicate that the family of the BDT-alt-FBTA-based D-A copolymers are high performance polymer donor materials for non-fullerene PSCs and the side chain engineering plays an important role in the design of high performance polymer donors in the non-fullerene PSCs.     

The mobility of threaded <Emphasis Type="Italic">α</Emphasis>-cyclodextrins in PR copolymer and its influences on mechanical properties

The methylated polyrotaxane (MePR) copolymer was prepared via the methylation of hydroxyl of threaded α-cyclodextrin (α-CDs) in polyrotaxane (PR) copolymer by CH₃I/NaH. Its structure was characterized by GPC, IR and NMR. The WXRD and TGA measurements showed the destruction of channel-like crystalline structure in MePR copolymer. The sliding of threaded α-CDs along PEG axis in PR and MePR copolymers was demonstrated by their dielectric spectra that also evidenced the presence of rotating of threaded α-CDs around PEG axis in MePR copolymer. The frequent and vigorous molecular mobility in MePR and PR copolymers was also verified by dynamic mechanical analysis (DMA) and rheological measurement, which was possibly assigned to the sliding and rotating of threaded α-CDs. DMA and rheological results showed that the mobility of α-CDs could simultaneously strengthen and toughen PR copolymer proved by stress-stain curves. In this paper, we report the CD mobility in PR and MePR copolymers. The macroscopic behaviors of PR copolymer, such as mechanical properties in solid state, were also found to be benefited from CD mobility.     

Synthesis of water soluble metalloporphyrin-cored amphiphilic star block copolymer photocatalysts for an environmental application

Two series of water-soluble metalloporphyrin-cored amphiphilic star block copolymers were synthesized by controlled radical polymerizations such as atom transfer radical polymerization (ATRP) and reversible addition fragmentation chain transfer (RAFT), which gave eight amphiphilic block copolymer arm chains consisting of poly(n-butyl acrylate-b-poly(ethylene glycol) methyl ether methacylate) (PnBA-b-PEGMEMA, M_n,GPC = 78,000, M_w/M_n = 1.2, 70 wt% of PPEGMEMA) and poly(styrene-b-2-dimethylamino ethyl acrylate) (PS-b-PDMAEA, M_n,GPC = 83,000, M_w/M_n = 1.2, 67 wt% of PDMAEA), yielding porphyrin(Pd)-(PnBA-b-PPEGMEMA)₈ and porphyrin(Pd)-(PS-b-PDMAEA)₈, respectively. Obtained metalloporphyrin polymer photocatalysts were homogeneously solubilized in water to apply to the removal of chlorophenols in water, and was distinguished from conventional water-insoluble small molecular metalloporphyrin photocatalysts. Notably, we found that the water-soluble star block copolymers with hydrophobic–hydrophilic core–shell structures more effectively decomposed the chlorophenol, 2,4,6-trichlorophenol (2,4,6-TCP), in water under visible light irradiation (k = 1.39 h^?1, t_1/2 = 0.5 h) in comparison to the corresponding water-soluble star homopolymer, because the hydrophobic core near the metalloporphyrin effectively captured and decomposed the hydrophobic chlorophenols in water.     

Aggregative behavior of AB and ABC block copolymers in the solid phase and in a nonselective solvent

Effects of the amount of chemically dissimilar blocks (two or three) and their polarity on the aggregative behavior of АВ and АВС linear block copolymers of various compositions that are based on polystyrene, poly(n-butyl acrylate), and either poly(acrylic acid) or poly(tert-butyl acrylate) in bulk and in the nonselective solvent DMF are studied via differential scanning calorimetry and dynamic light scattering. АВ block copolymers composed of two chemically dissimilar blocks in the diluted solution in DMF are fully dispersed into macromolecular coils. However, the simultaneous incorporation of three incompatible blocks of different polarities (polystyrene, poly(acrylic acid), and poly(n-butyl acrylate)) into the copolymer is accompanied by a well-defined segregation of blocks in the nonselective solvent, regardless of the composition of the block copolymer and the length and sequence of blocks. This phenomenon makes itself evident as the formation of intermacromolecular aggregates in diluted solutions with a mean hydrodynamic radius of 60–120 nm that are stable in the range 10–60°C. A decrease in the level of the thermodynamic incompatibility of blocks (replacement of a poly(acrylic acid) polar block with a less polar poly(tert-butyl acrylate) block) or the selective improvement of solvent quality with respect to the polar block (the addition of LiBr to DMF) suppresses the segregation of blocks and may lead to the formation of a molecularly dispersed solution of the block copolymer.     

Rheological behavior and reversible swelling of pH sensitive poly(acrylamide-<Emphasis Type="Italic">co</Emphasis>-itaconic acid) hydrogels

The study involved preparation of poly(acrylamide-co-itaconic acid) hydrogels by radical cross-linking copolymerization. The copolymer hydrogels were characterized through infrared spectroscopy, thermal analysis, swelling measurements and in oscillatory and steady shear rheology. Results showed that more stable copolymers were formed due to the strong interaction in the hydrogels. These hydrogels have shown substantial percent swelling in water and shrinking in saline solution and acidic buffers. The rheological properties were described by the Herschel-Bulkley and power-law models to explore their non-Newtonian behavior. The results showed that higher itaconic acid content raised the polymer viscosity; the degree of shear-thinning and polymer elasticity (G′) were also increased. The transition from the viscous (G′ < G″) to the predominant viscoelastic behavior (G′ > G″) occurs at a crossover frequency ranged from 17.8 rad/s for polyacrylamide to 15.7, 12.8 and 12.5 rad/s for copolymers.     

Emulsifier-free polymerization of <Emphasis Type="Italic">n</Emphasis>-butyl acrylate involving trithiocarbonates based on oligomer acrylic acid

The effect of the chain length of oligomer acrylic acid obtained in the presence of a low-molecularmass trithiocarbonate and the position of trithiocarbonate fragment (within the chain or at the chain end) on the process of emulsion polymerization of n-butyl acrylate and characteristics of the resulting dispersions has been studied for the first time. It has been found that, when using an oligomer with trithiocarbonate group located within the chain in the emulsion polymerization of n-butyl acrylate in a wide range of monomer–water phase compositions, triblock copolymers self-organizing in aqueous medium to give stable particles with the core–shell structure are formed. Oligomers with M _n ～ (5–10) × 10³ are optimal for synthesis of stable dispersions. In this case, block copolymers with the controlled length of hydrophobic block and a rather narrow MWD may be obtained. Thin films formed from these copolymers retain the structure of the initial dispersions on solvent removal. If the trithiocarbonate group in the oligomer is located at the chain end, the main polymerization product is a diblock copolymer. In this case, the formation of polymer–monomer particles occurs during a longer period of time, the control of MWD is weakened, and the dispersions of particles lose the aggregative stability after thin film formation.     

Physicochemical properties of multicomponent polyhydroxyalkanoates: Novel aspects

The physicochemical properties such as the degree of crystallinity and temperature and molecularmass characteristics of a number of polyhydroxyalkanoates of various chemical composition synthesized on a complex carbon substrate by bacteria Cupriavidus eutrophus В10646 have been investigated. Two-, three-, and four-component copolymer samples have different sets and ratios of monomers with various lengths of carbon chains: 3-hydroxybutyrate (3HB), 4-hydroxybutyrate (4HB), 3-hydroxyvalerate (3HV), 3-hydroxyhexanoate (3HH), 3-hydroxy-4-methyl valerate (3H4MV), and diethylene glycol (DEG). It has been shown that weight-average molar mass М _w and polydispersity vary in a wide range with no correlation existing with the composition of copolymer polyhydroxyalkanoates and that thermal stability is preserved in the temperature interval between the melting temperature and the thermal degradation temperature from 100 to 120–140°С. The composition and ratio of monomers most notably affect the degree of crystallinity of polyhydroxyalkanoates. Significant differences between the degrees of crystallinity of three- and four-component polyhydroxyalkanoates have been found for the first time. The degree of crystallinity for copolymers P(3HB/3HV/4HB) is 9–22%, and the degree of crystallinity for copolymers P(3HB/3HV/3HH) and P(3HB/3GV/3H4MV) is 41–63%; this value is close to the degree of crystallinity for diblock copolymers P(3HB)/DEG, which is 56–69%. For the four-component copolymers P(3HB/3GV/4HB/3HH), the degree of crystallinity is 30–41%. The values of М _w for the copolymers P(3HB/DEG) are inhomogeneous and the polymers contain fractions uneven with respect to molecular mass: a high-molecular-mass polymer (М _w from 2700 to 4900 kDa) and a low-molecular-mass polymer (М _w = 46–167 kDa). For the copolymers P(3HB)/DEG and P(3HB/3HV/3H4MV), two peaks are observed in the region of melting with the gap between these peaks being 4–20°С. All of the types of copolymer samples, regardless of the monomer ratio, show an increase in elongation at break against the background of a decrease in tensile stress and Young’s modulus, with these effects being pronounced to different extents. On the whole, the properties of multicomponent polyhydroxyalkanoates differ appreciably.     

Glucose-Mediated Insulin Release Carrier

Polyacrylic acid-co-methacrylamidophenylboronic acid) (PAA-co-PMAAPBA) copolymers were prepared using different concentrations of 3-methacrylamidophenylboronic acid (MAAPBA). The release of insulin from the insulin loaded polymer is dependent on the composition between acrylic acid and MAAPBA in the copolymer. With an increase in concentration of 3-methacrylamidophenylboronic acid, the glucose responsive insulin release from polyacrylic acid-co-methacrylamidophenylboronic acid) polymer at the physiological pH of 7.4 was enhanced. The presence of glucose resulted in disintegration of the polymer leading to release of the loaded insulin.     

Linear-Dendritic Block Copolymers Based on <Emphasis Type="Italic">N</Emphasis>-Isopropylacrylamide and Perfluorinated Polyphenylenegermane: Synthesis and Properties at Various Interfacial Boundaries

It is shown that linear-dendritic block copolymers poly(N-isopropylacrylamide)–block–polyphenylenegermane can be prepared by the polymerization of N-isopropylacrylamide in the presence of bis(pentafluorophenyl)germane followed by activated polycondensation with tris(pentafluorophenyl)germane. The properties of the dilute solutions and Langmuir monolayers of the functional polymers and the linear-dendritic block copolymers of N-isopropylacrylamide are studied.     

Semicontinuous microemulsion copolymerization of vinyl acetate and butyl acrylate: high solid content and effect of monomer addition rate

Vinyl acetate and butyl acrylate were copolymerized in microemulsion under monomer-starved conditions by a semicontinuous process using different monomer addition rates (R _a). A mixture of sodium dodecyl sulfate and polyethylene glycol dodecyl ether (Brij®35) were used as surfactants. Potassium persulfate was the initiator. High copolymer content latexes (around 40 wt.%), average particle diameters (D _p)?M _w) between 180,000 and 760,000. D _p and M _w of the copolymers decrease as R _a is decreased. As R _a increases, a shoulder in the molar mass distribution was observed at high values of M _w, which was ascribed to chain transfer to polymer. Homogeneous copolymer compositions were observed throughout the reaction, which cannot be obtained by the usual batch process.     

<Emphasis Type="Italic">In situ</Emphasis> synthesis of block copolymer nano-assemblies by polymerization-induced self-assembly under heterogeneous condition

Controlled synthesis of amphiphilic block copolymer nanoparticles in a convenient way is an important and interest topic in polymer science. In this review, three formulations of polymerization-induced self-assembly to in situ synthesize block copolymer nanoparticles are briefly introduced, which perform by reversible addition-fragmentation chain transfer (RAFT) polymerization under heterogeneous conditions, e.g., aqueous emulsion RAFT polymerization, dispersion RAFT polymerization and especially the recently proposed seeded RAFT polymerization. The latest developments in several selected areas on the synthesis of block copolymer nano-assemblies are highlighted.     

Controlled radical copolymerization of styrene and <Emphasis Type="Italic">tert</Emphasis>-butyl acrylate in the presence of tri-<Emphasis Type="Italic">n</Emphasis>-butylborane–<Emphasis Type="Italic">p</Emphasis>-quinone catalytic system

Radical copolymerization of styrene with tert-butyl acrylate is studied under different conditions. It is found that the addition of tri-n-butylborane or tri-n-butylborane along with p-quinones (2,3-dimethylbenzoquinone, 2,5-di-tert-butylbenzoquinone) results in changes in the relative activities of monomers. Copolymerization in the presence of tri-n-butylborane and p-quinones proceeds via the mechanism of reversible inhibition and is characterized by the linear increase in number-average molecular weight with conversion and by the capacity of copolymers of reinitiation. The hydrolyzed copolymer samples form more stable films compared to copolymers prepared via conventional radical copolymerization.     

The doubly thermo-responsive triblock copolymer nanoparticles prepared through seeded RAFT polymerization

The doubly thermo-responsive triblock copolymer nanoparticles of polystyrene-block-poly(N-isopropylacrylamide)-block-poly[N,N-(dimethylamino) ethyl methacrylate] (PS-b-PNIPAM-b-PDMAEMA) are successfully prepared through the seeded RAFT polymerization in situ by using the PS-b-PNIPAM-TTC diblock copolymer nanoparticles as the seed. The seeded RAFT polymerization undergoes a pseudo-first-order kinetics procedure, and the molecular weight increases with the monomer conversion linearly. The hydrodynamic diameter (D _h) of the triblock copolymer nanoparticles increases with the extension of the PDMAEMA block. In addition, the double thermo-response behavior of the PS-b-PNIPAM-b-PDMAEMA nanoparticles is detected by turbidity analysis, temperature-dependent 1H-NMR analysis, and DLS analysis. The seeded RAFT polymerization is believed as a valid method to prepare triblock copolymer nanoparticles containing two thermo-responsive blocks.     

Miniemulsion cross-linking: A convenient route to hollow polymeric nanocapsule with a liquid core

Miniemulsion stabilized by poly(2-(dimethylamino) ethyl methacrylate)-block-poly(butyl methylacrylate) (PDMAEMA-b-PBMA) diblock copolymers has been used as liquid templates for the synthesis of polymer nanocapsules via quaternization cross-linking of PDMAEMA segments of the copolymer by 1,2-bis(2-iodoethoxy)ethane (BIEE) crosslinkers. PDMAEMA-b-PBMAs here as a stabilizer in miniemulsion with different molecular weights led to a size variation in diameters of nanocapsules, demonstrating the capsules have potential design capability of this technique. The solution behavior of the capsules has been also investigated in this paper.     

New donor–acceptor copolymers with ultra-narrow band gap for photovoltaic application

Two novel donor–acceptor (D–A) copolymers P1 and P2 with the thiazoloquinoxaline repeating acceptor moiety and different donor moieties of benzo[1,2-b:4,5-b']dithiophene and isomeric benzo[2,1-b:3,4-b']dithiophene have been prepared. The polymers show light absorption at 300–1200 nm and a band gap width of 0.98 and 1.14 eV, respectively. The energies of the HOMO (–5.42 and–5.29 eV) and LUMO (–3.90 and–3.83 eV) levels of polymers P1 and P2 have been determined. The absorption maximum for polymer P1 in the long-wavelength region is red-shifted by 161 nm, which is caused by stronger charge transfer in P1 as compared with P2. This fact indicates that the benzo[1,2-b:4,5-b']dithiophene structural moiety has a higher electron-donating ability than the benzo[2,1-b:3,4-b']dithiophene moiety. The red shift of the absorption spectrum of polymer P1 in comparison with that of P2 indicates that interchain π–π stacking interactions are more efficient in P1 than in P2.     

Controlled synthesis of acrylic homo- and copolymers in the presence of trithiocarbonates as reversible addition-fragmentation chain transfer agents

Formation of homo- and copolymers of various structures (random and block) based on tert-butyl acrylate and n-butyl acrylate via polymerization mediated by trithiocarbonates as reversible addition-fragmentation chain-transfer agents has been studied. The process is found to proceed according to a three-stage mechanism. As a result, it is possible to synthesize symmetric triblock copolymers with the use of polymer trithiocarbonates; the polymer reversible addition-fragmentation chain transfer agent predetermines the composition and molecular mass of end blocks, the composition of the monomer mixture determines the structure of the central block, and the concentration of the agent and the conversion of the monomers define its molecular-mass characteristics. The modification of polymerization products gives rise to amphiphilic copolymers.     

Preparation,characterization and morphological study of poly(<Emphasis Type="Italic">m</Emphasis>-toluidine-<Emphasis Type="Italic">co</Emphasis>-<Emphasis Type="Italic">m</Emphasis>-aminoacetophenone) conductive copolymer

A new series of copolymers of poly(m-toluidine-co-m-aminoacetophenone) were synthesized by the chemical oxidative method in acid medium. The copolymers were characterized by UV–Vis and FTIR spectroscopy. X-ray diffraction analysis revealed the partial crystalline nature of copolymer. The morphological study by SEM analysis indicated that the surface of the copolymer had the granular structure of agglomerated morphology with average particle size of 200 nm. The conductivity of the copolymers ranged from 2 × 10^–4 to 3.3 × 10^–8 S/cm and the conductivity decreased with the increase of comonomer concentration. The resultant copolymers showed an enhanced solubility and an improved processability when compared with pure polyaniline.     

Biodegradable microspheres with poly(<Emphasis Type="Italic">N</Emphasis>-isopropylacrylamide) Enriched surface: Thermo-responsibility,biodegradation and drug release

Microspheres with thermo-responsible surface were fabricated by PCL-b-PEO-b-PNIPAM triblock copolymers. Thermo-responsible morphological changes of PCL-b-PEO-b-PNIPAM microspheres immersed in aqueous solution at temperatures above the LCST (e.g. 37 °C) were observed from porous surface structure to compact surface layer. Enzymatic degradation and in vitro drug release results showed that the thermo-responsible surface layer greatly influenced the degradation of microspheres as well as the drug release behavior from microspheres. With the copolymerization of PNIPAM block into PCL-b-PEO copolymers, the drug release could be well regulated by changing temperatures and microspheres composition, which revealed the great potentials of microspheres with thermo-responsible surface for controlled drug release.     

Micellization and gelation of the double thermoresponsive ABC-type triblock copolymer synthesized by RAFT

A double thermoresponsive ABC-type triblock copolymer(poly(ethyleneglycol)-block-poly(2-(2-methoxyethoxy) ethyl methacrylate)-block-poly(2-(2-methoxy ethoxy) ethyl methacrylate-co-oligo(ethylene glycol) methyl ether methacrylate, PEG-b-PMEO_2MA-b-P(MEO_2MA-co-OEGMA)) was designed and synthesized by reversible additionfragmentation chain transfer polymerization(RAFT). The ABC-type triblock copolymer endowed a thermal-induced twostep phase transition at 29 and 39 °C, corresponding to the thermosensitive properties of PMEO_2 MA and P(MEO_2MA-coOEGMA) segments, respectively. The two-step self-assembly of copolymer solutions was studied by UV transmittance measurement, dynamic light scattering(DLS), transmission electron microscopy(TEM) and so on. The triblock copolymers showed the distinct thermosensitive behavior with respect to transition temperatures, aggregate type and size, which was correlated to the degree of polymerization of thermosensitive blocks and the molar fraction of OEGMA in the P(MEO_2MAco-OEGMA) segments. In addition, micelles could further aggregate to form the hydrogel by the self-associate of PEG chains under the abduction of the concentration and temperature. The transition from sol to gel was investigated by a test tube inverting method and dynamic rheological measurement.     

Ultrasound-assisted synthesis of block copolymers of chitosan and <Emphasis Type="Italic">D</Emphasis>,<Emphasis Type="Italic">L</Emphasis>-lactide: Structure and properties

The block copolymers of chitosan with D,L-lactide are synthesized under UV irradiation of the homogeneous solution of the corresponding homopolymers with the yield of the main product being 96 wt %. The polyblock structure of copolymer chains, in which the size of polylactide blocks is varied in the range of (2.9–22.0) × 10³ depending on the synthesis conditions, is demonstrated. The incorporation of polylactide blocks into the structure of chitosan leads to development of the material structure close to the structure of polylactide. The films of the block copolymers containing 16 wt % polylactide and having a molecular mass of its blocks of 22.0 × 10³ have increased values of breaking stress (47 MPa) and ultimate strain (20%) compared to chitosan (24 MPa and 1.9%, respectively). The obtained block copolymers possess bactericidal properties.