On-line coupling of liquid chromatography,capillary gas chromatography and mass spectrometry for the determination and identification of polycyclic aromatic hydrocarbons in vegetable oils

Summary An on-line combination of liquid chromatography, gas chromatography and mass spectrometry has been realized by coupling a quadrupole mass spectrometer to an LC-GC apparatus. Liquid chromatography was used for sample pretreatment of oil samples of different origin. The appropriate LC fraction, containing polycyclic aromatic hydrocarbons, was transferred to the gas chromatograph using a loop-type interface. After solvent evaporation through the solvent vapour exit and subsequent GC separation, the compounds were introduced into the mass spectrometer for detection and identification. The GC column was connected to a short piece of deactivated fused silica that protruded into the ion source. The total analytical set-up allowed the direct analysis of oil samples after dilution in n-pentane without any sample clean-up. Detection limits are about 40 pg in the full scan mode and about 1 pg with selective ion monitoring, i.e. 20 ppb and 0.5 ppb respectively.     

色谱／质谱联用技术分析测定贻贝中的多环芳烃

介绍了ＧＣ－ＭＳ联用技术－物质征离子选择法测定贻贝中多环芳烃的分析方法，并就定性定量离子的选择，以及方法的准确度和精密度进行了探讨。结果表明，本方法适用于海洋生物贻贝，牡蛎中ＰＡＨｓ的分析测定。     

复杂基体中痕量多环芳烃分析测定方法的研究进展

介绍了环境样品（水和土壤）以及植物油中痕量多环芳烃的分析检测方法。对样品的预处理过程和分析方法做了评价。采用一些新的预处理方法（包括液相色谱法、固相萃取法、超临界二氧化碳萃取法）,并结合色谱-质谱在线联用分析检测方法能够获得比较理想的分析结果。引用文献52篇。     

Clean-up methods for polycyclic aromatic hydrocarbons analyses by capillary gas chromatography

Summary Comparative results of pre-treatment methods for the extracts of polycyclic aromatic hydrocarbons (PAHs) from airborne particulate matter for quantitative determination by gas chromatography (GC) are presented. The first method included liquid-liquid extraction and column liquid adsorption chromatography. In the second procedure the extract was fractionated by liquid-liquid chromatography and liquid adsorption chromatography. In the last procedure two different solid phase extraction (SPE) cartridges examined makes it possible to separate PAHs and remove paraffinic compounds which is very important for the quantitative GC analysis of the PAHs. Recoveries of PAH standards and some their derivatives were determined and the contents of 15 of the most important PAHs, were compared. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Identification of oxygenated polycyclic aromatic hydrocarbons in diesel particulate matter by capillary gas chromatography and capillary gas chromatography/mass spectrometry

Summary Using a two-step liquid chromatographic separation on normalphase cartridges, crude extracts of diesel particulate matter can be separated without time-consuming sample handling into special fractions which mainly contain slightly-polar oxygenated polycyclic aromatic hydrocarbons (oxy-PAH) and nitrated polycyclic aromatic hydrocarbons (nitro-PAH). Subsequent analysis was by fused-silica capillary gas chromatography on a SE54 column along with flame-ionisation (GC/FID) and positive-ion electron-impact mass spectrometric detection (GC/MS) respectively. A number of individual oxy-PAH belonging to four different chemical classes (ketones, quinones, anhydrides and aldehydes) and several individual nitro-PAH were characterized by their retention times and mass spectra. Presented at the 15th International Symposium on Chromatography, Nürnberg, October 1984     

全二维气相色谱-飞行时间质谱联用技术分析重馏分油中芳烃组成

通过对升温速度、二维补偿温度、调制周期等关键实验参数的优化,建立了全二维气相色谱-飞行时间质谱(GC×GC-TOF MS)分析重馏分油中芳烃组分的方法,得到了重馏分油芳烃组分按环数分布的二维点阵图。根据谱库检索、标准化合物对照及文献报道,对重馏分油芳烃组分中菲、甲基菲及芘、苯并蒽等常见多环芳烃(PAH)进行了准确定性,并将该方法应用到重馏分油加氢处理工艺研究中,对菲、芘的加氢处理产物进行了定性分析。该研究为重馏分油芳烃组分的准确定性提供了新的技术手段,为加深对油品加氢规律的认识提供了技术支持。全二维气相色谱与普通一维色谱对比,在重馏分油的芳烃组分分析上体现了极大优势。     

Automated clean-up, separation and detection of polycyclic aromatic hydrocarbons in particulate matter extracts from urban dust and diesel standard reference materials using a 2D-LC/2D-GC system

A multidimensional, on-line coupled liquid chromatographic/gas chromatographic system was developed for the quantification of polycyclic aromatic hydrocarbons (PAHs). A two-dimensional liquid chromatographic system (2D-liquid chromatography (LC)), with three columns having different selectivities, was connected on-line to a two-dimensional gas chromatographic system (2D-gas chromatography (GC)). Samples were cleaned up by combining normal elution and column back-flush of the LC columns to selectively remove matrix constituents and isolate well-defined, PAH enriched fractions. Using this system, the sequential removal of polar, mono/diaromatic, olefinic and alkane compounds from crude extracts was achieved. The LC/GC coupling was performed using a fused silica transfer line into a programmable temperature vaporizer (PTV) GC injector. Using the PTV in the solvent vent mode, excess solvent was removed and the enriched PAH sample extract was injected into the GC. The 2D-GC setup consisted of two capillary columns with different stationary phase selectivities. Heart-cutting of selected PAH compounds in the first GC column (first dimension) and transfer of these to the second GC column (second dimension) increased the baseline resolutions of closely eluting PAHs. The on-line system was validated using the standard reference materials SRM 1649a (urban dust) and SRM 1975 (diesel particulate extract). The PAH concentrations measured were comparable to the certified values and the fully automated LC/GC system performed the clean-up, separation and detection of PAHs in 16 extracts in less than 24 h. The multidimensional, on-line 2D-LC/2D-GC system eliminated manual handling of the sample extracts and minimised the risk of sample loss and contamination, while increasing accuracy and precision.

Sample preparation procedure for the determination of polycyclic aromatic hydrocarbons in petroleum vacuum residue and bitumen

This paper describes a novel method of sample preparation for the determination of trace concentrations of polycyclic aromatic hydrocarbons (PAHs) in high-boiling petroleum products. Limits of quantitation of the investigated PAHs in materials of this type range from tens of nanograms per kilogram to <20 μg/kg. The studies revealed that in order to separate most of interferences from the analytes without a significant loss of PAHs, it is necessary to use size exclusion chromatography as the first step of sample preparation, followed by adsorption using normal-phase liquid chromatography. The use of orthogonal separation procedure described in the paper allows the isolation of only a group of unsubstituted and substituted aromatic hydrocarbons with a specific range of molar mass. The lower the required limit of quantitation of PAHs, the larger is the scale of preparative liquid chromatography in both steps of sample preparation needed. The use of internal standard allows quantitative results to be corrected for the degree of recovery of PAHs during the sample preparation step. Final determination can be carried out using HPLC-FLD, GC-MS, or HPLC-UV–VIS/DAD. The last technique provides a degree of identification through the acquired UV–VIS spectra.     

超高效液相色谱法检测土壤中的多环芳烃

采用二极管阵列(PDA)检测器,建立了超高效液相色谱(UPLC)定性定量分析土壤中16种多环芳烃(PAHs)的方法。并将该方法与传统高效液相色谱(HPLC)的分析性能进行了详细的比较。研究结果表明,采用UPLC法分析16种PAHs具有分析速度快(13.5 min)、检出限低(2～20 pg)、灵敏度高等优点。     

GC�CMS Determination of PAHs in Fish Samples Following Salting-out-Assisted Solvent Extraction-Gel Permeation Chromatography

A fast and effective sample cleanup procedure for the quantification of polycyclic aromatic hydrocarbons (PAHs) in fish samples is presented. The procedure involved extraction of fish samples using acetonitrile and cleanup by an automated gel-permeation chromatography (GPC) following liquid?Cliquid partition into n-hexane. The extracted samples were analyzed by gas chromatography-mass spectrometry (GC?CMS). Electron ionization was employed in a single analysis for the determination of PAHs in the selected ion monitoring mode. Three different solvents were studied for the extraction step: acetonitrile/n-hexane, methanol/n-hexane and acetone/n-hexane. The best solvent was found to be acetonitrile/n-hexane. The cleanup technique resulted in a good separation of analytes from co-extractive matrix compounds.     

In-source fragmentation of partially oxidized mono- and polycyclic aromatic hydrocarbons in atmospheric pressure chemical ionization mass spectrometry coupled to liquid chromatography

Partially oxidized derivatives of polycyclic aromatic hydrocarbons (PAHs) are known to be important environmental pollutants. For the identification of these substances in complex mixtures, e.g. atmospheric aerosol samples, liquid chromatography/mass spectrometry with atmospheric pressure chemical ionization (LC/APCI-MS) has been found to be a suitable analytical technique. In this study 31 derivatives of mono- and polycyclic aromatic hydrocarbons with up to five condensed aromatic rings carrying different functional groups (carboxyl, dicarboxylic anhydride, lactone, hydroxyl, and carbonyl) were characterized by LC/APCI-MS. Each substance was measured in positive and negative ion detection mode at four different fragmentor voltages (90 to 190 V). For the first time, the results show that characteristic and well-interpretable fragmentation patterns can be obtained for these classes of compounds by in-source collision-induced dissociation in a single quadrupole LC/APCI-MS system. For each class of compounds typical spectral features and optimum measurement conditions are reported, and fragmentation pathways are proposed. The study demonstrates the applicability of LC/APCI-MS for the determination of most of the investigated compounds at trace levels, and it provides a database for the identification of unknown partially oxidized aromatic hydrocarbons. Copyright 1999 John Wiley & Sons, Ltd.     

Trace-level analysis of polychlorinated biphenyls,organochlorine pesticides and polycyclic aromatic hydrocarbons in human plasma or serum by dispersive liquid–liquid microextraction and gas chromatography–tandem mass spectrometry

A method to determine 8 polychlorinated biphenyls (PCBs), 23 organochlorine pesticides (OCPs) and 16 polycyclic aromatic hydrocarbons (PAHs) was described using dispersive liquid–liquid microextraction (DLLME) of a small amount of plasma or serum sample and gas chromatography–tandem mass spectrometry (GC–MS/MS). The appropriate selection of the extraction solvent and dispersing solvent contributes to a high extraction yield and a clean extract. To verify the developed method, the interference, linearity of the calibration curve, detection limit, precision and accuracy were evaluated. The calibration curves were linear by 2–3 orders of magnitude with correlation coefficients above 0.997 in all cases. The LODs of PCBs, OCPs and PAHs were measured in the ranges of 0.0006–0.0029, 0.001–0.029 and 0.0002–0.012 ng/mL. The intraday precision achieved by this method was 2.19–10.3% (PCBs), 1.65–14.3% (OCPs) and 0.91–12.8% (PAHs), and the intraday accuracy 1.56–7.37% (PCBs), 2.34–19.6% (OCPs) and 1.49–15.7% (PAHs). The advantage of this method is that the analysis of PCBs, OCPs, and PAHs can be performed in a single chromatographic run, and the low detection limit enables monitoring of target substances in low exposure general public samples, and the analysis procedure is relatively simple and fast.     

Supersonic molecular beam-hyperthermal surface ionisation coupled with time-of-flight mass spectrometry applied to trace level detection of polynuclear aromatic hydrocarbons in drinking water for reduced sample preparation and analysis time

Analysis of sub-ppb levels of polynuclear aromatic hydrocarbons (PAHs) in drinking water by high performance liquid chromatography (HPLC) fluorescence detection typically requires large water samples and lengthy extraction procedures. The detection itself, although selective, does not give compound identity confirmation. Benchtop gas chromatography/mass spectrometry (GC/MS) systems operating in the more sensitive selected ion monitoring (SIM) acquisition mode discard spectral information and, when operating in scanning mode, are less sensitive and scan too slowly. The selectivity of hyperthermal surface ionisation (HSI), the high column flow rate capacity of the supersonic molecular beam (SMB) GC/MS interface, and the high acquisition rate of time-of-flight (TOF) mass analysis, are combined here to facilitate a rapid, specific and sensitive technique for the analysis of trace levels of PAHs in water. This work reports the advantages gained by using the GC/HSI-TOF system over the HPLC fluorescence method, and discusses in some detail the nature of the instrumentation used.     

Determination of polycyclic aromatic hydrocarbons in edible oils and fats by on-line donor-acceptor complex chromatography and high-performance liquid chromatography with fluorescence detection

Various off-line methods for clean-up and sample enrichment are available for the analysis of polycyclic aromatic hydrocarbons (PAHs) in edible oils and fats. These methods consist of laborious and time consuming procedures. This study reports an on-line method using LC-LC coupling. After clean-up of the sample on a donor-acceptor complex chromatography (DACC) column the PAHs are transferred to and separated on an analytical HPLC column. Quantification is carried out with fluorescence detection. The DACC column clean-up is fast and is carried out during the HPLC run of the previous sample. Compared to the traditional methods this automated on-line method saves considerable time and significantly reduces the amount of solvent waste. The method uses common HPLC equipment and its performance has been evaluated.     

Analysis of polycyclic aromatic hydrocarbons (PAHs) in environmental samples: a critical review of gas chromatographic (GC) methods

Polycyclic aromatic hydrocarbons (PAHs) are frequently measured in the atmosphere for air quality assessment, in biological tissues for health-effects monitoring, in sediments and mollusks for environmental monitoring, and in foodstuffs for safety reasons. In contemporary analysis of these complex matrices, gas chromatography (GC), rather than liquid chromatography (LC), is often the preferred approach for separation, identification, and quantification of PAHs, largely because GC generally affords greater selectivity, resolution, and sensitivity than LC. This article reviews modern-day GC and state-of-the-art GC techniques used for the determination of PAHs in environmental samples. Standard test methods are discussed. GC separations of PAHs on a variety of capillary columns are examined, and the properties and uses of selected mass spectrometric (MS) techniques are presented. PAH literature on GC with MS techniques, including chemical ionization, ion-trap MS, time-of-flight MS (TOF-MS), and isotope-ratio mass spectrometry (IRMS), is reviewed. Enhancements to GC, for example large-volume injection, thermal desorption, fast GC, and coupling of GC to LC, are also discussed with regard to the determination of PAHs in an effort to demonstrate the vigor and robustness GC continues to achieve in the analytical sciences.     

Screening and confirmation of PAHs in vegetable oil samples by use of supercritical fluid extraction in conjunction with liquid chromatography and fluorimetric detection

A fast, simple, non-destructive method for the direct screening of polycyclic aromatic hydrocarbons (PAHs) in vegetable oil samples is proposed. The method uses a supercritical fluid extraction (SFE) system coupled on-line with a fluorimetric detector to determine PAHs. This special assembly avoids the main problems encountered in the determination of PAHs in complex matrices such as vegetable oils. PAHs are selectively extracted by using silica gel in the thimble and cleaned up by passage through a C18 column. Interferences are preferentially retained by the silica gel during the SFE process while PAHs are adsorbed in the C18 column and the remainder of the matrix is sent to waste. Finally, the C18 column is purged to remove residual CO₂ gas and adsorbed PAHs are recovered by desorption with a solvent. The extracts from positive samples are subsequently analyzed by liquid chromatography (LC) with fluorescence detection. The proposed method allows the confirmation of vegetable oil safety and hence provides a new tool for consumer protection.     

Quantification of 16 polycyclic aromatic hydrocarbons in cigarette smoke condensate using stable isotope dilution liquid chromatography with atmospheric‐pressure photoionization tandem mass spectrometry

A stable isotope dilution liquid chromatography tandem mass spectrometry method for the analysis of 16 polycyclic aromatic hydrocarbons in cigarette smoke condensate was developed and validated. Compared with previously reported methods, this method has lower limits of detection (0.04–1.35 ng/cig). Additionally, the proposed method saves time, reduces the number of separation steps, and reduces the quantity of solvent needed. The new method was applied to evaluate polycyclic aromatic hydrocarbon content in 213 commercially available cigarettes in China, under the International Standardization Organization smoking regime and the Health Canadian intense smoking regime. The results showed that the total polycyclic aromatic hydrocarbon content was more than two times higher in samples from the Health Canadian intense smoking regime than in samples from the International Standardization Organization smoking regime (1189.23 versus 2859.50 ng/cig, p < 0.05). Meanwhile, the concentration of individual polycyclic aromatic hydrocarbons (and total polycyclic aromatic hydrocarbons) increased with labeled tar content in both of the tested smoking regimes. There was a positive correlation between total polycyclic aromatic hydrocarbons under the International Standardization Organization smoking regime with that under the Health Canadian intense smoking regime. The proposed liquid chromatography tandem mass spectrometry method is satisfactory for the rapid, sensitive, and accurate quantitative evaluation of polycyclic aromatic hydrocarbon content in cigarette smoke condensate, and it can be applied to assess potential health risks from smoking.     

Structure-type separation of diesel fuels by solid phase extraction and identification of the two- and three-ring aromatics by capillary GC-mass spectrometry

A simple and effective solid phase extraction (SPE) method using silica gel micro glass columns has been developed for the separation of diesel fuel into groups of aliphatic, and mono-, di- and polyaromatic hydrocarbons. It is based on a stepwise gradient of dichloromethane in n-pentane. The resulting fractions were analyzed by capillary gas chromatography with a flame ionization detector and coupled gas chromatography-mass spectrometry. Commercially available standards, and retention indices and mass spectra were used for identification of individual aromatic compounds. The principal polycyclic aromatic hydrocarbons (PAHs) in diesel fuel are naphthalene, biphenyl, fluorene, phen-anthrene and their alkylated derivatives. Sulfur-containing PAHs are mainly represented by methyl-substituted dibenzo-thiophenes.     

Simple calibration procedure for comprehensive two-dimensional gas chromatography

Mass transfer from the first-dimension to the second-dimension column in comprehensive two-dimensional gas chromatography (GC x GC) is normally quantitative, which means that the peak areas produced by GC x GC are equal to those obtained in one-dimensional gas chromatography (GC). In view of this relationship, it was investigated whether normal GC calibration could be used to quantify compounds analysed by GC x GC. Quantification of polycyclic aromatic hydrocarbons (PAHs) in sediment was used as a test case. It was concluded that more laborious and time-consuming GC x GC area calibration can be replaced by GC area calibration if separation quality and quantity prerequisites are met.     

The study of properties of HPLC determination of polycyclic aromatic nitrogen heterocycles

The study of the separation of polycyclic aromatic nitrogen heterocycles (PANHs) by reverse-phase liquid chromatography with an octadecyl stationary phase is presented. The retention behaviour of a mixture of PANHs was studied under different chromatographic conditions. A mixture of phosphate buffer/acetonitrile was used as mobile phase in isocratic and gradient modes. The effect of different pH mobile phase in the range from 2.5 to 6.5 has been investigated to describe retention changes of PANHs as a function of their acid/base properties. Different concentrations of phosphate buffer as a component of the mobile phase were used to study the effect of ionic strength. Very good RP-HPLC separation of 24 PANHs and 16 EPA polycyclic aromatic hydrocarbons (PAHs) was obtained without a pre-separation step in a test mixture and the extract of a real soil sample. Limits of detection of PANHs obtained by two detection techniques, ultraviolet-diode array detection (UV-DAD) and fluorescence detector (FD), are compared. The proposed method is tested with a real soil sample.