五氧化二钽纳米柱的水热合成和光催化性能（英文）

以聚乙烯醇(PEG)为结构导向剂,利用水热法合成了形貌可控的Ta2O5纳米柱.采用X射线衍射、扫描电镜、透射电镜、漫反射紫外-可见光谱和光致发光光谱对所制备样品进行了表征.考察了结晶时间和Ta2O5/Sr(OH)2摩尔比等合成参数对样品形貌的影响,并在此基础上对Ta2O5纳米粒可能的生长机理进行了推测.结果表明,在PEG和Sr(OH)2存在条件下可以合成形貌可控的Ta2O5纳米柱.研究了紫外光下Ta2O5纳米柱降解罗丹明B的光催化性能,发现Ta2O5的形貌对光催化性能有很大影响,Ta2O5纳米柱的光催化性能与其长度和直径比成线性关系.催化降解反应的表观速率常数最高可达0.156 min–1,且经多次循环使用后,样品仍然保持较高的催化性能.     

K1.9Na0.1Ta2O6·2H2O的形貌可控合成及光催化性能

钽酸盐光催化材料往往具有较高的光催化活性.近年报道的钽酸盐光催化剂主要采用传统高温固相法制备,该方法不可避免地导致高温烧结,使合成的钽酸盐颗粒较大,比表面积较小,而且该方法具有不可克服的晶体转变、结晶度差、分解、挥发和纯度低等缺点,使制备的光催化剂活性较低.而纳米材料由于粒径小,提高了电子和空穴的扩散速度,大大降低了电子和空穴在材料内的复合几率,从而使光催化材料活性大幅提高.此外,粒径减小也使表面原子迅速增多,减小了光的漫反射,同时也使光吸收不易达到饱和,有利于提高光吸收效率.因此,制备纳米材料是提高半导体光催化剂活性的有效手段.目前,采用湿化学的溶液合成方法能在较低温度下获得粒度小且均匀、计量比准确的光催化剂粉末,但是合成钽酸盐光催化剂的水溶性钽前体即乙醇钽(或氯化钽)价格昂贵,而且对潮湿极端敏感易水解,使产物纯度降低,不适合工业化生产.近年来,尽管有文献报道以Ta2O5为原料利用水热、溶胶-凝胶和共沉淀等方法制备钽酸盐,但其合成条件苛刻,合成步骤复杂,合成周期较长,耗能大,产物产量较低且不均匀,很难实现产物的形貌控制来筛选出适合光催化反应的材料.目前关于纳米钽酸盐光催化材料形貌控制方面的研究鲜有报道,主要是由于Ta2O5极难溶解,很难实现液相合成.因此,纳米钽酸盐光催化材料的可控制备是研究的难点.我们发展了熔盐-水热制备钽酸盐新方法,实现了K1.9Na0.1Ta2O6·2H2O的可控制备.利用熔盐法制备一种可溶性钽酸盐前驱体,再通过水热法在液相进一步反应制得纳米钽酸盐光催化材料K1.9Na0.1Ta2O6·2H2O,通过控制反应条件实现了纳米钽酸盐K1.9Na0.1Ta2O6·2H2O的形貌调控,得到了纳米球、微球、去顶八面体形貌和类似榴莲形貌等不同形貌,而利用其它制备方法很难控制钽酸盐的形貌.另外,研究了制备材料吸附和光催化降解罗丹明B的性能,发现该材料光催化活性与形貌直接相关.表征结果表明,制备样品的X射线衍射(XRD)谱图尖锐,结晶较好,其各衍射峰位置均与K2Ta2O6一致,为纯相烧绿石结构,属于立方晶系,空间群为Fd3m.通过分析合成材料的元素组成及含量,确定K：Na：Ta比例近似为1.9：0.1：2.为了进一步研究属于烧绿石型化合物K1.9Na0.1Ta2O6·2H2O的结构,对不同形貌材料进行了红外光谱测试,所有样品在450–1000 cm–1的谱峰可归属于(K, Na)–O和Ta–O键的振动,3300 cm–1左右为晶体结构中水的羟基伸缩振动峰,1720 cm–1左右是晶体结构中水的弯曲振动峰.可以看出,不同形貌材料的红外谱图吸收带宽度和位置十分相似,只存在小的偏移和变化,进一步表明不同形貌的材料具有相似的晶体结构,与XRD结果一致.差热-热重分析确定了结构中所含结晶水数量近似为2.光催化性能测试结果表明,具有纳米球形貌的材料比表面积较大,因而光催化活性最高.     

K_(1.9)Na_(0.1)Ta_2O_6·2H_2O的形貌可控合成及光催化性能（英文）

钽酸盐光催化材料往往具有较高的光催化活性.近年报道的钽酸盐光催化剂主要采用传统高温固相法制备,该方法不可避免地导致高温烧结,使合成的钽酸盐颗粒较大,比表面积较小,而且该方法具有不可克服的晶体转变、结晶度差、分解、挥发和纯度低等缺点,使制备的光催化剂活性较低.而纳米材料由于粒径小,提高了电子和空穴的扩散速度,大大降低了电子和空穴在材料内的复合几率,从而使光催化材料活性大幅提高.此外,粒径减小也使表面原子迅速增多,减小了光的漫反射,同时也使光吸收不易达到饱和,有利于提高光吸收效率.因此,制备纳米材料是提高半导体光催化剂活性的有效手段.目前,采用湿化学的溶液合成方法能在较低温度下获得粒度小且均匀、计量比准确的光催化剂粉末,但是合成钽酸盐光催化剂的水溶性钽前体即乙醇钽(或氯化钽)价格昂贵,而且对潮湿极端敏感易水解,使产物纯度降低,不适合工业化生产.近年来,尽管有文献报道以Ta2O5为原料利用水热、溶胶-凝胶和共沉淀等方法制备钽酸盐,但其合成条件苛刻,合成步骤复杂,合成周期较长,耗能大,产物产量较低且不均匀,很难实现产物的形貌控制来筛选出适合光催化反应的材料.目前关于纳米钽酸盐光催化材料形貌控制方面的研究鲜有报道,主要是由于Ta2O5极难溶解,很难实现液相合成.因此,纳米钽酸盐光催化材料的可控制备是研究的难点.我们发展了熔盐-水热制备钽酸盐新方法,实现了K1.9Na0.1Ta2O6·2H2O的可控制备.利用熔盐法制备一种可溶性钽酸盐前驱体,再通过水热法在液相进一步反应制得纳米钽酸盐光催化材料K1.9Na0.1Ta2O6·2H2O,通过控制反应条件实现了纳米钽酸盐K1.9Na0.1Ta2O6·2H2O的形貌调控,得到了纳米球、微球、去顶八面体形貌和类似榴莲形貌等不同形貌,而利用其它制备方法很难控制钽酸盐的形貌.另外,研究了制备材料吸附和光催化降解罗丹明B的性能,发现该材料光催化活性与形貌直接相关.表征结果表明,制备样品的X射线衍射(XRD)谱图尖锐,结晶较好,其各衍射峰位置均与K2Ta2O6一致,为纯相烧绿石结构,属于立方晶系,空间群为Fd3m.通过分析合成材料的元素组成及含量,确定K:Na:Ta比例近似为1.9:0.1:2.为了进一步研究属于烧绿石型化合物K1.9Na0.1Ta2O6·2H2O的结构,对不同形貌材料进行了红外光谱测试,所有样品在450–1000 cm–1的谱峰可归属于(K,Na)–O和Ta–O键的振动,3300 cm–1左右为晶体结构中水的羟基伸缩振动峰,1720 cm–1左右是晶体结构中水的弯曲振动峰.可以看出,不同形貌材料的红外谱图吸收带宽度和位置十分相似,只存在小的偏移和变化,进一步表明不同形貌的材料具有相似的晶体结构,与XRD结果一致.差热-热重分析确定了结构中所含结晶水数量近似为2.光催化性能测试结果表明,具有纳米球形貌的材料比表面积较大,因而光催化活性最高.     

简单低温水浴法合成鳞片状氧化铜/四针状氧化锌晶须复合光催化剂(英文)

以硝酸铜为原料,聚乙二醇(PEG,Mw=400)为稳定剂和模板剂,采用简单的低温水浴合成法成功合成了四针状氧化锌晶须(T-ZnOw)表面负载鳞片状CuO的纳米复合光催化剂,系统研究了复合催化剂样品的晶体结构和形貌,通过荧光发光光谱(PL)和紫外光照射的条件下样品对阳离子污染物(亚甲蓝,MB)和阴离子污染物(甲基橙,MO)的光催化降解效率表征了样品的光催化性能,同时采用ICP-AES详细分析了PEG 400浓度对T-ZnOw表面负载CuO纳米颗粒数量的影响.结果表明,T-ZnOw表面有序地沉积了大量鳞片状CuO纳米颗粒,随着PEG 400浓度增加,T-ZnOw表面沉积的CuO纳米片数量逐渐增多,且CuO纳米片在T-ZnOw表面的排列更加有序.同时,PEG 400浓度的变化对合成样品特征发光峰的强度也有一定影响,当PEG 400浓度小于0.60 mol/L时,合成样品特征发光峰强度随着PEG 400浓度增大而减小;当PEG 400浓度大于0.60 mol/L时,样品的特征发光峰强度随之有所增加.在紫外光照射条件下,CuO/T-ZnOw纳米复合催化剂样品对MB和MO水溶液的降解均表现出优异的光催化活性,当PEG 400浓度≤0.60 mol/L时,样品的光催化活性随着PEG 400浓度的增大而增加;而当PEG 400浓度大于0.60 mol/L时,样品的光催化活性反而有所降低.此外,在相同条件下,所有样品对MB水溶液的降解效率明显高于对MO水溶液的降解效率.     

立方晶型Sb2O3纳米晶的合成及光催化性能

采用沉淀法合成了立方晶型Sb2O3纳米晶,通过X射线衍射(XRD)、扫描电镜(SEM)、透射电镜(TEM)、紫外-可见漫反射光谱(UV-Vis DRS)和电子自旋共振谱(ESR)等对样品进行了详细的表征。以紫外光光催化降解甲基橙为反应模型评价了样品的光催化性能。结果表明:沉淀法合成的立方晶型Sb2O3纳米晶颗粒小,表现出良好的光催化性能。对立方晶型Sb2O3纳米晶光催化降解甲基橙的原因进行了探讨,并提出了降解甲基橙的反应机理。     

花状Cu2O/Cu的水热合成及其光催化性能

以硝酸铜为前驱体, 不采用任何模板, 通过逐步水热法合成了花状Cu2O/Cu复合纳米材料. 用扫描电镜(SEM)、X射线衍射(XRD)和紫外-可见漫反射光谱(DRS)对样品进行表征. 结果表明, 花状纳米Cu2O/Cu材料是由长为300-500 nm, 宽为30-70 nm的带状花瓣构成, 在可见光区域有很强的吸收. 复合材料中Cu的含量可以通过反应时间进行调控. 对染料Procion Red MX-5B(PR)的可见光催化降解, Cu能明显提高Cu2O的光催化性能. 当Cu质量分数为27%-71%时, 复合材料Cu2O/Cu的催化活性明显高于单相Cu2O. 与立方体形貌的Cu2O/Cu复合材料相比, 花状纳米Cu2O/Cu复合材料对染料PR有更高的催化降解性能. 且该复合材料有较高的循环回收利用率.     

Ag修饰的Fe_3O_4/TiO_2复合磁性纳米纤维的制备及光催化性能

通过静电纺丝法制备了含有Fe3O4纳米粒子的TiO2纳米纤维,采用水热法对该纤维表面进行纳米Ag修饰,制备出具有较强磁性和较好光催化性能的复合纤维.采用X射线衍射(XRD)、扫描电子显微镜(SEM)、透射电子显微镜(TEM)和紫外-可见光谱(UV-Vis)等对样品的结构和形貌进行表征,并以罗丹明B(Rh B)水溶液降解为模型反应,考察样品在紫外光照射下的光催化性能.结果表明,所制备的TiO2为锐钛矿结构,Fe3O4纳米粒子均匀分布在TiO2纤维中,Ag纳米颗粒比较均匀地分散在磁性TiO2纤维表面.经过纳米Ag修饰后,材料的光吸收能力大为增强,吸收带红移并扩展到可见光区.在紫外光照射40 min后,合成样品对Rh B的降解率达到99.5%.此外,Fe3O4纳米粒子的存在使该材料具有较强的磁性,可通过外加磁场将其分离回收.     

层状、花形和棒状钛酸铋纳米结构的可控合成及光催化性能

通过可控水热法,制备出层状、花形和棒状钛酸铋(Bi4Ti3O12,BIT)纳米结构。通过X射线衍射(XRD)和场发射扫描电子显微镜(FESEM)观测其结构和形貌特征。XRD图显示,所制备的样品为层状钙钛矿结构。FESEM结果表明,通过控制水热过程的反应参数可以得到不同形貌的纳米粉体。紫外-可见漫反射光谱(UV-Vis DRS)表明BIT样品的带隙能约为2.63～2.95 eV。利用可见光(λ>420 nm)照射下的甲基橙降解实验评价了BIT样品的光催化性能。结果表明,BIT的光催化活性比掺氮TiO2(N-TiO2)高得多。所制备的层状BIT纳米结构光催化效率最高,经可见光照射360 min,甲基橙溶液的降解率可达95.0%。同时还研究了结构和形貌对不同条件下制备的BIT样品光催化活性的影响。     

F~-离子对C掺杂Nb_2O_5纳米粒子生长及光催化性能的影响

在合成C掺杂Nb2O5的基础上,通过引入F-离子合成出具有更高光催化活性的C,F共掺杂Nb2O5光催化材料,对合成样品进行了分析、表征并测试了其光降解罗丹明B的活性,研究了F-离子对C掺杂Nb2O5纳米粒子生长及光催化性能的影响.结果表明,在合成过程中引入F-离子能够促进Nb2O5纳米晶的生长,尤其是沿[001]方向的生长.实验结果还表明,F未进入Nb2O5纳米晶的晶格内部,而是以F-离子的形式分散在Nb2O5纳米结构中,通过促进Nb2O5表面·OH自由基的产生,起到提高合成样品光催化活性的作用.     

复合半导体MoS_2/Cu_2O的制备及其光催化性能研究

采用两步法制备了MoS_2/Cu_2O催化剂,对其催化降解甲基橙(MO)性能进行了研究.首先,通过液相剥离和梯度离心获得少数层MoS_2纳米片,然后采用水热还原法在MoS_2纳米片上合成Cu_2O纳米颗粒,形成MoS_2/Cu_2O复合半导体,并分别通过扫描电子显微镜(SEM)、X射线衍射(XRD)、X射线光电子能谱(XPS)、UV-Vis紫外可见漫反射光谱(DRS)等手段对催化剂的结构进行表征.在可见光下,MoS_2/Cu_2O复合半导体降解MO的效率明显高于纯MoS_2和Cu_2O.为了获得最佳光催化活性,探究了MoS_2质量分数(5%、10%、20%、30%、40%、50%)对MoS_2/Cu_2O复合半导体光催化降解MO的影响.最后,经过5次循环实验,MoS_2/Cu_2O降解率下降为82.5%,循环稳定性有待进一步提高.     

Synthesis of hexagonal BaTa2O6 nanorods and influence of defects on the photocatalytic activity

Hexagonal barium tantalate (BaTa2O6) nanorods were synthesized by a hydrothermal method based on the reaction of concentrated Ba(OH)2 solution and Ta2O5. BaTa2O6 samples show a uniform cylindrical structure with diameters of 5-30 nm and the lengths of 50-200 nm. The formation of BaTa2O6 nanorods follows a dissolution-recrystallization mechanism and is governed by hydrothermal temperature and time. BaTa2O6 nanorod samples prepared at 270 degrees C for 72 h have exhibited the highest photocatalytic activity in the degradation of Rhodamine B (RhB) in aqueous solution under UV radiation. Hydrogen-related defects were detected in BaTa2O6 nanorods, which originate from the oxygen octahedron. The number of defects was dependent on the hydrothermal temperature, and the photocatalytic activities of BaTa2O6 nanorods increase with the decrease of defect amounts. On the basis of the experiment results, the difference in photocatalytic activities for samples is mainly caused by lattice defects, which can act as inactivation centers.     

Mapping the Compositions of Zinc Tantalate for Optimum Photocatalytic Performance in Degradation of Organic Pollutants

This work aims at mapping the compositions of zinc tantalate for optimum photocatalytic performance in degradation of organic pollutants. Three zinc tantalates, low-temperature form ZnTa2O6 (LT-ZnTa2O6), high-temperature form ZnTa2O6 (HT-ZnTa2O6), and Zn3Ta2O8 were prepared by solid state method. Photocatalytic activities of these zinc tantalates were tested for the degradation of methyl orange under UV irradiation and compared with Sr2Ta2O7, an efficient catalyst previously reported. It is found that the photocatalytic activity of these tantalates follows such a sequence: LT-ZnTa2O6 > Sr2Ta2O7 > HT-ZnTa2O6 > Zn3Ta2O8, in which LT-ZnTa2O6 shows an optimum activity at least twice higher than Sr2Ta2O7. This photocatalytic performance was revealed to primarily originate from the formation of ·OH radicals as indicated by photo- luminescence measurements. The synergistic effects of chemical compositions, crystal structure, and band structure on photocatalytic performances were discussed.     

Synthesis of magnesium oxychloride nanorods with controllable morphology and their transformation to magnesium hydroxide nanorods via treatment with sodium hydroxide

In this paper, the formation of magnesium oxychloride (Mg_x(OH)_yCl_z·nH₂O) nanorods from the system MgO-MgCl₂-H₂O is investigated thoroughly. By systematically changing the adding amounts of the three starting materials, short nanorods (<1 μ) or long nanorods (up to 20 μ) were obtained readily with the aspect ratio in the range of 10–70. The mechanism of the crystal growth and the change of the crystal phase from 5Mg(OH)₂·MgCl₂·8H₂O (phase 5) to 3Mg(OH)₂·MgCl₂·8H₂O (phase 3) is also discussed. The products were characterized by transmission electron microscopy X-ray diffraction, energy-dispersive X-ray spectroscopy, and thermogravimetric analysis. The resulting magnesium oxychloride nanorods were further transformed to magnesium hydroxide (Mg(OH)₂) nanorods with the shape remained by treating with NaOH at room temperature. The results shown in this paper indicate a facile pathway to produce magnesium oxychloride or magnesium hydroxide nanorods with controllable morphology on large scale.     

Polymer-assisted growth of molybdenum oxide whiskers via a sonochemical process

Whiskers of molybdenum oxides with high aspect ratios were synthesized from peroxomolybdate precursor solutions in the presence of small amounts of poly(ethylene glycol) (PEG) via a sonochemical process at temperatures of 25-70 degrees C. Irradiation with ultrasound reduces the time needed for the growth of micrometer-sized whiskers from weeks to a few hours. The simplicity of the sonochemical approach also compares favorably to a hydrothermal/solvothermal process. The morphology, crystal structure, and other characteristics of the whiskers were characterized by scanning electron microscopy, transmission electron microscopy, selective area electron diffraction, energy-dispersive X-ray spectroscopy, wide-angle X-ray diffraction, Raman spectroscopy, thermogravimetric analysis, differential scanning calorimetry, and the Brunauer-Emmett-Teller method. The surface area of the calcified molybdenum oxide whiskers (55.4 m2/g) was found to be much higher than those of molybdenum oxide nanofibers (35 m2/g) or nanorods (13.4 m2/g) The growth rate of various crystal faces could be postulated to be controlled by the binding of peroxomolybdate ions to pseudo-crown ether cavities formed by PEG. The reduction of molybdenum oxide to produce mixed-valent oxides and their growth could also be controlled by the reducing ability of PEG. The aspect ratio of the molybdenum oxide whiskers increased with decreasing concentration in the initial peroxomolybdate precursor solution. Whether the precursor solution species was H2Mo2O3(O2)4(H2O)2, H2MoO2(O2)2, or MoO2(OH)(OOH), the peroxide group in all the species disproportionates to give the final product MoO3 by a catalytic process. On the basis of experimental evidence of the dual role of glycols, a mechanism for the growth of the molybdenum oxide whiskers is proposed.     

Hierarchical nanostructures of fluorinated and naked Ta2O5 single crystalline nanorods: hydrothermal preparation, formation mechanism and photocatalytic activity for H2 production

The hydrolysis of H(2)TaF(7) when it slowly forms via etching Ta powders with HF and H(2)O(2) under hydrothermal conditions produces hierarchical nanostructures of fluorinated and naked Ta(2)O(5) single-crystalline nanorods, which exhibit a far greater photocatalytic activity for H(2) production than commercial Ta(2)O(5) particles.     

球磨-溶剂热诱导法合成WS2纳米棒及其摩擦性能

采用行星式高能球磨机，将WS₂与S粉末混合球磨，得到纳米片状结构的前驱体，然后添加分散剂聚乙二醇(PEG)用溶剂热诱导的方法使纳米片状前驱体发生结构转变，制备了棒状结构的WS₂纳米材料。用XRD、SEM、TEM等方法对WS₂纳米棒进行了形貌和结构表征，并对其作为润滑油添加剂的摩擦性能进行了初步的研究。     

有机胺柱类钙钛矿型钽酸盐的制备与表征

采用分步交换法，合成了新型的正丙胺、正丁胺柱层状类钙钛矿型钽酸盐C3H7NH3-Sr2Ta3O10与C4H9NH3-Sr2Ta7O10，采用X射线衍射(XRD)、扫描电镜(SEM)、红外光谱(IR)对该类化合物的结构与形貌进行了表征，并测定了其比表面积。     

Matrix isolation infrared spectroscopic and theoretical studies on the reactions of niobium and tantalum mono- and dioxides with methane

The reactions of niobium and tantalum monoxides and dioxides with methane have been investigated using matrix isolation infrared spectroscopic and theoretical calculations. The niobium and tantalum oxide molecules were prepared by laser evaporation of Nb(2)O(5) and Ta(2)O(5) bulk targets. The niobium monoxide molecule interacted with methane to form the ONb(CH(4)) complex, which was predicted to have C(3)(v)() symmetry with the metal atom coordinated to three hydrogen atoms of the methane molecule. The ONb(CH(4)) complex rearranged to the CH(3)Nb(O)H isomer upon 300 nm < lambda < 580 nm irradiation. The analogous OTa(CH(4)) complex was not observed, but the CH(3)Ta(O)H molecule was produced upon UV irradiation. The niobium and tantalum dioxide molecules reacted with methane to form the O(2)Nb(CH(4)) and O(2)Ta(CH(4)) complexes with C(s)() symmetry, which underwent photochemical rearrangement to the CH(3)Nb(O)OH and CH(3)Ta(O)OH isomers upon ultraviolet irradiation.     

氧化锌纳米棒的水热合成及其光催化性能

以分析纯ZnO作为锌源、NaOH为矿化剂、盐酸为反应溶液pH调节剂,利用水热反应制备了花状ZnO纳米棒;采用扫描电子显微镜和X射线衍射仪分析了产物的形貌和结构,考察了水热温度以及Zn2+和OH-浓度比对产物形貌的影响;以甲基橙为目标降解物,采用紫外-可见分光光度计研究了ZnO纳米棒的光催化性能.结果表明,在水热反应温度80℃、Zn2+/OH-浓度比1∶7.5条件下所得ZnO纳米棒呈花状聚合,直径约为200nm,长度约为2μm,具有六方纤锌矿结构.当甲基橙初始浓度为30 mg.L-1、ZnO纳米棒的投放量为1.5g.L-1时,以300W紫外灯照射150min,甲基橙的降解率可达90%.     

(Ba, Sr)TiO3纳米棒的反相微乳法制备与表征

在氢氧化钡和氢氧化锶水溶液/Triton X-100/环己烷/正己醇四元W/O型反相微乳液中制备了钛酸锶钡纳米棒, 研究了ω₀值(水与表面活性剂Triton X-100的物质的量之比)、反应物浓度、陈化时间对产品形貌和尺寸的影响, 用TEM, SAED, SEM, EDS和XRD等技术对产品进行了表征. 结果表明, 所得Ba_0.7Sr_0.3TiO₃纳米棒长约500～1200 nm、直径约为50～120 nm; 具有立方相单晶结构. 产品中钡、锶、钛的物质的量之比约为0.7∶0.3∶1.