Ethanol production from corn starch in a fluidized-bed bioreactor

The production of ethanol from industrial dry-milled corn starch was studied in a laboratory-scale fluidized-bed bioreactor using immobilized biocatalysts. Saccharification and fermentation were carried out either simultaneously or separately. Simultaneous saccharification and fermentation (SSF) experiments were performed using small, uniform κ-carrageenan beads (1.5–2.5 mm in diameter) of co-immobilized glucoamylase and Zymomonas mobilis. Dextrin feeds obtained by the hydrolysis of 15% drymilled corn starch were pumped through the bioreactor at residence times of 1.5–4h. Single-pass conversion of dextrins ranged from 54–89%, and ethanol concentrations of 23–36 g/L were obtained at volumetric productivities of 9–15 g/L-h. Very low levels of glucose were observed in the reactor, indicating that saccharification was the rate-limiting step. In separate hydrolysis and fermentation (SHF) experiments, dextrin feed solutions of 150–160 g/L were first pumped through an immobilized-glucoamylase packed column. At 55°C and a residence time of 1 h, greater than 95% conversion was obtained, giving product streams of 162–172 g glucose/L. These streams were then pumped through the fluidized-bed bioreactor containing immobilized Z. mobilis. At a residence time of 2 h, 94% conversion and ethanol concentration of 70 g/L were achieved, resulting in an overall process productivity of 23 g/L-h. Atresidence times of 1.5 and 1 h, conversions of 75 and 76%, ethanol concentrations of 49 and 47 g/L, and overall process productivities of 19 and 25 g/L-h, respectively, were achieved.     

Continuous culture studies of xylose-fermentingZymomonas mobilis

The continuous cofermentation performance of xylose-fermentingZymomonas mobilis at 30°C and pH 5.5 was characterized using a pure-sugar feed solution that contained 8 g/L glucose and 40 g/L xylose. Successful chemostat start up resulted in complete utilization of glucose and greater than 85% utilization of xylose, but was only reproducibly achieved using initial dilution rates at or less than 0.04/h; once initiated, cofermentation could be maintained at dilution rates of 0.04 to 0.10/h. Whereas xylose and cell-mass concentrations increased gradually with increasing dilution rate, ethanol concentrations and ethanol yields on available sugars remained approximately constant at 20–22 g/L and 80–90% of theoretical, respectively. Volumetric and specific ethanol productivities increased linearly with increasing dilution rate, rising from approx 1.0 each (g/L/h or g/g/h) at a dilution rate of 0.04/h to approx 2.0 each (g/L/h or g/g/h) at a dilution rate of 0.10/h. Similarly, specific sugar-utilization rates increased from approx 2.0 g/g/h at dilution rate 0.04/h to approx 3.5 g/g/h at dilution rate of 0.10/h. The estimated values of 0.042 g/g for the maximum Z.mobilis cell-mass yield on substrate and 1.13 g/g/h for the minimum specific substrate utilization rate required for cellular maintenance energy are within the range of values reported in the literature. Results are also presented which suggest that long-term adaptation in continuous culture is a powerful technique for developing strains with higher tolerance to inhibitory hemicellulose hydrolyzates.     

Ethanol Production from Wet-Exploded Wheat Straw Hydrolysate by Thermophilic Anaerobic Bacterium Thermoanaerobacter BG1L1 in a Continuous Immobilized Reactor

Thermophilic ethanol fermentation of wet-exploded wheat straw hydrolysate was investigated in a continuous immobilized reactor system. The experiments were carried out in a lab-scale fluidized bed reactor (FBR) at 70°C. Undetoxified wheat straw hydrolysate was used (3–12% dry matter), corresponding to sugar mixtures of glucose and xylose ranging from 12 to 41 g/l. The organism, thermophilic anaerobic bacterium Thermoanaerobacter BG1L1, exhibited significant resistance to high levels of acetic acid (up to 10 g/l) and other metabolic inhibitors present in the hydrolysate. Although the hydrolysate was not detoxified, ethanol yield in a range of 0.39–0.42 g/g was obtained. Overall, sugar efficiency to ethanol was 68–76%. The reactor was operated continuously for approximately 143 days, and no contamination was seen without the use of any agent for preventing bacterial infections. The tested microorganism has considerable potential to be a novel candidate for lignocellulose bioconversion into ethanol. The work reported here also demonstrates that the use of FBR configuration might be a viable approach for thermophilic anaerobic ethanol fermentation.     

Development of new ethanologenic Escherichia coli strains for fermentation of lignocellulosic biomass

Two new ethanologenic strains (FBR4 and FBR5) of Escherichia coli were constructed and used to ferment corn fiber hydrolysate. The strains carry the plasmid pLO1297, which contains the genes from Zymomonas mobilis necessary for efficiently converting pyruvate into ethanol. Both strains selectively maintained the plasmid when grown anaerobically. Each culture was serially transferred 10 times in anaerobic culture with sugar-limited medium containing xylose, but noselective antibiotic. An average of 93 and 95% of the FBR4 and FBR5 cells, respectively, maintained pLO1297 in anaerobic culture. The fermentation performances of the repeatedly transferred cultures were compared with those of cultures freshly revived from stock in pH-controlled batch fermentations with 10% (w/v) xylose. Fermentation results were similar for all the cultures. Fermentations were completed within 60 h and ethanol yields were 86–92% of theoretical. Maximal ethanol concentrations were 3.9–4.2% (w/v). The strains were also tested for their ability to ferment corn fiber hydrolysate, which contained 8.5% (w/v) total sugars (2.0% arabinose, 2.8% glucose, and 3.7% xylose). E. coli FBR5 produced more ethanol than FBR4 from the corn fiber hydrolysate. E. coli FBR5 fermented all but 0.4% (w/v) of the available sugar, whereas strain FBR4 left 1.6% unconsumed. The fermentation with FBR5 was completed within 55 h and yielded 0.46 g of ethanol/g of available sugar, 90% of the maximum obtainable. Author to whom all correspondence and reprint requests should be addressed. Names are necessary to report factually on available data. However, the USDA neither guarantees nor warrants the standard of the product, and the use of the name by USDA im plies no approval of the product to the exclusion of others that may also be suitable.     

Characterization of a high-productivity recombinant strain of Zymomonas mobilis for ethanol production from glucose/xylose mixtures

The fermentation characteristics of a recombinant strain of Zymomonas mobilis ZM4(pZB5) capable of converting both glucose and xylose to ethanol have been further investigated. Previous studies have shown that the strain ZM4(pZB5) was capable of converting a mixture o 65 g/L of glucose and 65 g/L of xylose to 62 g/L of ethanol in 48 h with an overall yield of 0.46 g/g. Higher sugar concentrations (e.g., 75/75 g/L) resulted in incomplete xylose utilization (80 h). In the present study, further kinetic evaluations at high sugar levels are reported. Acetate inhibition studies and evaluation of temperature and pH effects indicated increased maximum specific uptake rates of glucose and xylose under stressed conditions with increased metabolic uncoupling. A high-productivity system was developed that involved a membrane bioreactor with cell recycling. At sugar concentrations of approx 50/50 g/L of glucose/xylose, an ethanol concentration of 50 g/L, an ethanol productivity of approx 5 g/(L·h), and a yield (Y _p/s) of 0.50 g/g were achieved. Decreases in cell viability were found in this system after attainment of an initial steady state (40–60 h); a slow bleed of concentrated cells may be required to overcome this problem.     

Fermentation performance characteristics of a prehydrolyzate-adapted xylose-fermenting recombinant Zymomonas in batch and continuous fermentations

Long-term (149 d) continuous fermentation was used to adapt a xylose-fermenting recombinant Zymomonas mobilis, strain 39676:pZB 4L, to conditioned (overlimed) dilute-acid yellow poplar hemicellulose hydrolyzate (“prehydrolyzate”). An “adapted” variant was isolated from a chemostat operating at a dilution rate of 0.03/h with a 50% (v/v) prehydrolyzate, corn steep liquor, and sugar-supplemented medium, at pH 5.75. The level of xylose and glucose in the medium was kept constant at 4% (w/v) and 0.8% (w/v), respectively. These sugar concentrations reflect the composition of the undiluted hardwood prehydrolyzate. The level of conditioned hardwood prehydrolyzate added to the medium was increased in 5% increments startingata level of 10%. At the upper level of 50% prehydrolyzate, the acetic-acid concentration was about 0.75% (w/v). The adapted variant exhibited improved xylose-fermentation performance in a pure-sugar, synthetic hardwood prehydrolyzate medium containing 4% xylose (w/v), 0.8% (w/v) glucose, and acetic acid in the range 0.4–1.0% (w/v). The ethanol yield was 0.48–0.50 g/g; equivalent to a sugar-to-ethanol conversion efficiency of 94–96% of theoretical maximum. The maximum growth yield and maintenance energy coefficients were 0.033 g dry cell mass (DCM)/g sugars and 0.41 g sugars/g DCM/h, respectively. The results confirm that long-term continuous adaptation is a useful technique for effecting strain improvement with respect to the fermentation of recalcitrant feedstocks.     

Characterization of a Recombinant Flocculent Saccharomyces cerevisiae Strain that Co-ferments Glucose and Xylose: I. Influence of the Ratio of Glucose/Xylose on Ethanol Production

Glucose/xylose mixtures (90 g/L total sugar) were evaluated for their effect on ethanol fermentation by a recombinant flocculent Saccharomyces cerevisiae, MA-R4. Glucose was utilized faster than xylose at any ratio of glucose/xylose, although MA-R4 can simultaneously co-ferment both sugars. A high percentage of glucose can increase cell biomass production and therefore increase the rate of glucose utilization (1.224 g glucose/g biomass/h maximum) and ethanol formation (0.493 g ethanol/g biomass/h maximum). However, the best ratio of glucose/xylose for the highest xylose consumption rate (0.209 g xylose/g biomass/h) was 2:3. Ethanol concentration and yield increased and by-product (xylitol, glycerol, and acetic acid) concentration decreased as the proportion of glucose increased. The maximum ethanol concentration was 41.6 and 21.9 g/L after 72 h of fermentation with 90 g/L glucose and 90 g/L xylose, respectively, while the ethanol yield was 0.454 and 0.335 g/g in 90 g/L glucose and 90 g/L xylose media, respectively. High ethanol yield when a high percentage of glucose is available is likely due to decreased production of by-products, such as glycerol and acetic acid. These results suggest that ethanol selectivity is increased when a higher proportion of glucose is available and reduced when a higher proportion of xylose is available.     

Comparative ethanol productivities of different Zymomonas recombinants fermenting oat hull hydrolysate

Iogen Corporation of Ottawa, Canada, has recently built a 50 t/d biomass-to-ethanol demonstration plant adjacent to its enzyme production facility. Iogen has partnered with the University of Toronto to test the C6/C5 cofermentation performance characteristics of National Renewable Energy Laboratory's metabolically engineered Zymomonas mobilis using its biomass hydrolysates. In this study, the biomass feedstock was an agricultural waste, namely oat hulls, which was hydrolyzed in a proprietary two-stage process involving pretreatment with dilute sulfuric acid at 200–250°C, followed by cellulase hydrolysis. The oat hull hydrolysate (OHH) contained glucose, xylose, and arabinose in a mass ratio of about 8:3:0.5. Fermentation media, prepared from diluted hydrolysate, were nutritionally amended with 2.5 mL/L of corn steep liquor (50% solids) and 1.2 g/L of diammonium phosphate. The estimated cost for large-scale ethanol production using this minimal level of nutrient supplementation was 4.4c/gal of ethanol. This work examined the growth and fermentation performance of xyloseutilizing, tetracycline-resistant, plasmid-bearing, patented, recombinant Z. mobilis cultures: CP4:pZB5, ZM4:pZB5, 39676:pZB4L, and a hardwood prehydrolysate-adapted variant of 39676:pZB4L (designated asthe “adapted” strain). In pH-stat batch fermentations with unconditioned OHH containing 6% (w/v) glucose, 3% xylose, and 0.75% acetic acid, rec Zm ZM4:pZB5 gave the best performance with a fermentation time of 30h, followed by CP4:pZB5 at 48h, with corresponding volumetric productivities of 1.4 and 0.89 g/(L·h), respectively. Based on the available glucose and xylose, the process ethanol yield for both strains was 0.47 g/g (92% conversion efficiency). At 48 h, the process yield for rec Zm 39676:pZB4L and the adapted strain was 0.32 and 0.34 g/g, respectively. None of the test strains was able to fermentarabinose. Acetic acid tolerance appeared to be a major determining factor in cofermentation performance.     

Fermentation kinetics of ethanol production from glucose and xylose by recombinant Saccharomyces 1400(pLNH33)

Fermentation kinetics of ethanol production from glucose, xylose, and their mixtures using a recombinant Saccharomyces 1400 (pLNH33) are reported. Single-substrate kinetics indicate that the specific growth rate of the yeast and the specific ethanol productivity on glucose as the substrate was greater than on xylose as a substrate. Ethanol yields from glucose and xylose fermentation were typically 95 and 80% of the theoretical yield, respectively. The effect of ethanol inhibition is more pronounced for xylose fermentation than for glucose fermentation. Studies on glucose-xylose mixtures indicate that the recombinant yeast co-ferments glucose and xylose. Fermentation of a 52.8 g/L glucose and 56.3 g/L xylose mixture gave an ethanol concentration of 47.9 g/L after 36 h. Based on a theoretical yield of 0.51 g ethanol/g sugars, the ethanol yield from this experiment (for data up to 24 h) was calculated to be 0.46 g ethanol/g sugar or 90% of the theoretical yield. The specific growth rate of the yeast on glucose-xylose mixtures was found to lie between the specific growth rate on glucose and the specific growth rate on xylose. Kinetic studies were used to develop a fermentation model incorporating the effects of substrate inhibition, product inhibition, and inoculum size. Good agreements were obtained between model predictions and experimental data from batch fermentation of glucose, xylose, and their mixtures.     

Operability and feasibility of ethanol production by immobilizedZymomonas mobilis in a fluidized-bed bioreactor

Studies have been carried out using immobilized Z.mobilis in fluidized-bed bioreactors and have emphasized operation during high productivity and conversion. The bacteria are immobilized within small uniform beads (~1 to 1.5-mm diam) of K-carrageenan at cell loadings of 15-50 g (dry wt)/L. Conversion and productivity were measured under a variety of conditions, including feedstocks, flow rates, temperature, pH, and column sizes (up to 2.5 m tall). Volumetric productivities of 50-120 g EtOH/h-L reactor volume have been achieved. Productivities of 60 g/h-L are demonstrated from a 15% feed with residual glucose concentrations of less than 0.1% and 7.4% EtOH in the tallest fermentor. Among feeds of 10, 15, and 20% dextrose, the 15% gave the highest productivity and avoided substrate inhibition. A temperature of 30°C and pH 5 were the optimum conditions. The ethanol yield was shown to be nearly constant at 0.49 g EtOH/g glucose, or 97% of the theoretical under a variety of conditions and transients. The biocatalyst beads have been shown to remain active for two months. Nonsterile feed has been used for weeks without detrimental contamination. The advantages of this advanced bioreactor system over conventional batch technology are discussed.     

Production of Butyric Acid from Glucose and Xylose with Immobilized Cells of <Emphasis Type="Italic">Clostridium tyrobutyricum</Emphasis> in a Fibrous-bed Bioreactor

Butyric acid has many applications in chemical, food, and pharmaceutical industries. In the present study, Clostridium tyrobutyricum ATCC 25755 was immobilized in a fibrous-bed bioreactor to evaluate the performance of butyrate production from glucose and xylose. The results showed that the final concentration and yield of butyric acid were 13.70 and 0.46 g g⁻¹, respectively, in batch fermentation when 30 g L⁻¹ glucose was introduced into the bioreactor. Furthermore, high concentration 10.10 g L⁻¹ and yield 0.40 g g⁻¹ of butyric acid were obtained with 25 g L⁻¹ xylose as the carbon source. The immobilized cells of C. tyrobutyricum ensured similar productivity and yield from repeated batch fermentation. In the fed-batch fermentation, the final concentration of butyric acid was further improved to 24.88 g L⁻¹ with one suitable glucose feeding in the fibrous-bed bioreactor. C. tyrobutyricum immobilized in the fibrous-bed bioreactor would provide an economically viable fermentation process to convert the reducing sugars derived from plant biomass into the final bulk chemical (butyric acid).     

Influence of inhibitory compounds and minor sugars on xylitol production by <Emphasis Type="Italic">Debaryomyces hansenii</Emphasis>

To obtain in-depth information on the overall metabolic behavior of the new good xylitol producer Debaryomyces hansenii UFV-170, batch bioconversions were carried out using semisynthetic media with compositions simulating those of typical acidic hemicellulose hydrolysates of sugarcane bagasse. For this purpose, we used media containing glucose (4.3–6.5 g/L), xylose (60.1–92.1 g/L), or arabinose (5.9–9.2 g/L), or binary or ternary mixtures of them in either the presence or absence of typical inhibitors of acidic hydrolysates, such as furfural (1.0–5.0 g/L), hydroxymethylfurfural (0.01–0.30 g/L), acetic acid (0.5–3.0 g/L), and vanillin (0.5–3.0 g/L). D. hansenii exhibited a good tolerance to high sugar concentrations as well as to the presence of inhibiting compounds in the fermentation media. It was able to produce xylitol only from xylose, arabitol from arabinose, and no glucitol from glucose. Arabinose metabolization was incomplete, while ethanol was mainly produced from glucose and, to a lesser less extent, from xylose and arabinose. The results suggest potential application of this strain in xyloseto-xylitol bioconversion from complex xylose media from lignocellulosic materials.     

Continuous Production of Oxytetracycline in Fluidized Bed Bioreactor by Immobilized Cells of Streptomyces varsoviensis MTCC-1537: Effect of Dilution and Glucose Loading Rates

Oxytetracycline (OT) production using glutaraldehyde cross-linked calcium alginate immobilized cells of Streptomyces varsoviensis in continuous fluidized bed reactor (FBR) was investigated. Initially, batch experiments were carried in stirred tank reactor (STR) and FBR using calcium alginate immobilized cells. Higher OT production of 0.45 gm/L was achieved by FBR when compared with 0.33 g/L of OT in STR. All subsequent studies were carried out in continuous mode of operation in FBR. During 21 days of operation, effect of glucose concentration and different dilution rates were studied. A maximum of 0.75 g/L OT was achieved in the medium having 10 g/L of glucose concentration. The highest OT concentration of 0.92 g/L and the highest yield of OT with respect to biomass at 0.1713 g/g were obtained at the dilution rate of 0.25 day⁻¹.     

Model compound studies

The influence of other hemicellulosic sugars (arabinose, galactose, mannose, and glucose), oxygen limitation, and initial xylose concentration on the fermentation of xylose to xylitol was in vestigated using experimental design methodology. Oxygen limitation and initial xylose concentration had strong influences on xylitol production by Candida tropicalis ATCC 96745. Under semiaerobic conditions, xylitol yield was highest (0.62 g/g), whereas under aerobic conditions volumetric productivity was highest (0.90g/[L·h]). In the presence of glucose, xylose utilization was strongly repressed and sequential sugar utilization was observed. Ethanol produced from the glucose caused a 50% reduction in xylitol yield when the ethanol con centration exceeded 30 g/L. When complex synthetic hemicellulosic sugars were fermented, glucose was initially consumed followed by a simultaneous uptake of the other sugars. The highest xylitol yield (0.84 g/g) and volumetric productivity (0.49 g/[L·h]) were obtained for substrates containing high arabinose and low glucose and mannose contents.     

Production of ethanol from starch by co-immobilizedZymomonas mobilis-glucoamylase in a fluidized-bed reactor

The production of ethanol from starch was studied in a fluidized-bed reactor (FBR) using co-immobilizedZymomonas mobilis and glucoamylase. The FBR was a glass column of 2.54 cm in diameter and 120 cm in length. TheZ. mobilis and glucoamylase were co-immobilized within small uniform beads (1.2-2.5 mm diameter) of κ-carrageenan. The substrate for ethanol production was a soluble starch. Light steep water was used as the complex nutrient source. The experiments were performed at 35κC and pH range of 4.0-5.5. The substrate concentrations ranged from 40 to 185 g/L, and the feed rates from 10 to 37 mL/min. Under relaxed sterility conditions, the FBR was successfully operated for a period of 22 d, during which no contamination or structural failure of the biocatalyst beads was observed. Volumetric productivity as high as 38 g ethanol/(Lh), which was 74% of the maximum expected value, was obtained. Typical ethanol volumetric productivity was in the range of 15-20 g/(Lh). The average yield was 0.49 g ethanol/g substrate consumed, which was 90% of the theoretical yield. Very low levels of glucose were observed in the reactor, indicating that starch hydrolysis was the rate-limiting step.     

Fermentation performance assessment of a genomically integrated xylose-utilizing recombinant of Zymomonas mobilis 39676

In pH-controlled batch fermentations with pure sugar synthetic hardwood hemicellulose (1% [w/v] glucose and 4% xylose) and corn stover hydrolysate (8% glucose and 3.5% xylose) lacking acetic acid, the xyloseutilizing, tetracycline (Tc)-sensitive, genomically integrated variant of Zymomonas mobilis ATCC 39676 (designated strain C25) exhibited growth and fermentation performance that was inferior to National Renewable Energy Laboratory's first-generation, Tc-resistant, plasmid-bearing Zymomonas recombinants. With C25, xylose fermentation following glucose exhaustion wasmarkellyslower, and the ethanol yield (based on sugars consumed) was lower, owing primarily to an increase in lactic acid formation. There was an apparent increased sensitivity to acetic acid inhibition with C25 compared with recombinants 39676:pZB4L, CP4:pZB5, and ZM4:pZB5. However, strain C25 performed well in continous ferm entation with nutrient-rich synthetic corn stover medium over the dilution range 0.03–0.06/h, with a maximum provess ethanol yield at D=0.03/h of 0.46 g/g and a maximum ethanol productivity of 3 g/(L·h). With 0.35% (w/v) acetic acid in the medium, the process yield at D=0.04/h dropped to 0.32 g/g, and the maximum productivity decreased by 50% to 1.5 g/(L·h). Under the same operating conditions, rec Zm Zm 4:pZB5 performed better; however, the medium contained 20 mg/L of Tc to constantly maintain selective pressure. The absence of any need for antibiotics and antiboitic resistance genes makes the chromosomal integrant C25 more com patible with current regulatory specifications for biocatalysts in large-scale commercial operations.     

Continuous Production of Ethanol from Starch Using Glucoamylase and Yeast Co-Immobilized in Pectin Gel

This work presents a continuous simultaneous saccharification and fermentation (SSF) process to produce ethanol from starch using glucoamylase and Saccharomyces cerevisiae co-immobilized in pectin gel. The enzyme was immobilized on macroporous silica, after silanization and activation of the support with glutaraldehyde. The silica–enzyme derivative was co-immobilized with yeast in pectin gel. This biocatalyst was used to produce ethanol from liquefied manioc root flour syrup, in three fixed bed reactors. The initial reactor yeast load was 0.05 g wet yeast/ml of reactor (0.1 g wet yeast/g gel), used in all SSF experiments. The enzyme concentration in the reactor was defined by running SSF batch assays, using different amount of silica–enzyme derivative, co-immobilized with yeast in pectin gel. The chosen reactor enzyme concentration, 3.77 U/ml, allowed fermentation to be the rate-limiting step in the batch experiment. In this condition, using initial substrate concentration of 166.0 g/l of total reducing sugars (TRS), 1 ml gel/1 ml of medium, ethanol productivity of 8.3 g/l/h was achieved, for total conversion of starch to ethanol and 91% of the theoretical yield. In the continuous runs, feeding 163.0 g/l of TRS and using the same enzyme and yeast concentrations used in the batch run, ethanol productivity was 5.9 g ethanol/l/h, with 97% of substrate conversion and 81% of the ethanol theoretical yield. Diffusion effects in the extra-biocatalyst film seemed to be reduced when operating at superficial velocities above 3.7 × 10⁻⁴ cm/s.     

Xylitol production from wood hydrolyzates by entrapped Debaryomyces hansenii and Candida guilliermondii cells

Debaryomyces hansenii cells were entrapped in Ca-alginate beads and used for producing xylitol from wood hydrolyzates. Batch experiments showed that bioconversion was severely hindered when Ca-alginate beads were hardened with Al³⁺ solutions. As an alternative to Al³⁺ hardening, the improvements in both mechanical stability of bioparticles and fermenting ability of the immobilized system derived from using increased concentrations of sodium alginate were assessed. The best results were obtained using a 4% (w/v) Na-alginate solution in the gelification step. This concentration was selected to perform continuous fermentations in a packed-bed reactor using raw or charcoal-treated hydrolyzates (15.5 g of xylose/L) with two different yeasts: Candida guilliermondii and Debaryomyces hansenii. With a final cell concentration of about 50 g of cells/L (0.075 g of cells/g of beads), the volumetric productivities reached with these yeasts in media made from charcoal-treated hydrolyzates were 0.58 and 0.91 g/L·h, respectively.     

Continuous fermentation studies with xylose-utilizing recombinant Zymomonas mobilis

This study examined the continuous cofermentation performance characteristics of a dilute-acid “prehydrolysate-adapted” recombinant Zymomonas 39676:pZB4L and builds on the pH-stat batch fermentations with this recombinant that we reported on last year. Substitution of yeast extract by 1% (w/v) corn steep liquor (CSL) (50% solids) and Mg (2 mM) did not alter the coferm entation performance. Using declared assumptions, the cost of using CSL and Mg was estimated to be 12.5c/gal of ethanol with a possibility of 50% cost reduction using fourfold less CSL with 0.1% diammonium phosphate. Because of competition for a common sugar transporter that exhibits a higher affinity for glucose, utilization of glucose was complete whereas xylose was always present in the chemostat effluent. The ethanol yield, based on sugar used, was 94% of theoretical maximum. Altering the sugar ratio of the synthetic dilute acid hardwood prehydrolysate did not appear to significantly change the pattern of xylose utilization. Using a criterion of 80% sugar utilization for determining the maximum dilution rate (D _max), changing the composition of the feed from 4% xylose to 3%, and simultaneously increasing the glucose from 0.8 to 1.8% shifted D _max from 0.07 to 0.08/h. With equal amounts of both sugars (2.5%), D _max was 0.07/h. By comparison to a similar investigation with rec Zm CP4:pZB5 with a 4% equal mixture of xylose and glucose, we observed that at pH 5.0, the D _max was 0.064/h and shifted to 0.084/h at pH 5.75. At a level of 0.4% (w/v) acetic acid in the CSL-based medium with 3% xylose and 1.8% glucose at pH 5.75, the D _max for the adapted recombinant shifted from 0.08 to 0.048/h, and the corresponding maximum volumetric ethanol productivity decreased 45%, from 1.52 to 0.84 g/(L·h). Under these conditions of continuous culture, linear regression of a Pirt plot of the specific rate of sugar utilization vs D showed that 4 g/L of acetic acid did not affect the maximum growth yield (0.030 g dry cell mass/g sugar), but did increase the maintenance coefficient twofold, from 0.46 to 1.0 g of sugar/(g of cell·h).     

A Novel Technique that Enables Efficient Conduct of Simultaneous Isomerization and Fermentation (SIF) of Xylose

Of the sugars recovered from lignocellulose, d-glucose can be readily converted into ethanol by baker’s or brewer’s yeast (Saccharomyces cerevisiae). However, xylose that is obtained by the hydrolysis of the hemicellulosic portion is not fermentable by the same species of yeasts. Xylose fermentation by native yeasts can be achieved via isomerization of xylose to its ketose isomer, xylulose. Isomerization with exogenous xylose isomerase (XI) occurs optimally at a pH of 7–8, whereas subsequent fermentation of xylulose to ethanol occurs at a pH of 4–5. We present a novel scheme for efficient isomerization of xylose to xylulose at conditions suitable for the fermentation by using an immobilized enzyme system capable of sustaining two different pH microenvironments in a single vessel. The proof-of-concept of the two-enzyme pellet is presented, showing conversion of xylose to xylulose even when the immobilized enzyme pellets are suspended in a bulk solution whose pH is sub-optimal for XI activity. The co-immobilized enzyme pellets may prove extremely valuable in effectively conducting “simultaneous isomerization and fermentation” (SIF) of xylose. To help further shift the equilibrium in favor of xylulose formation, sodium tetraborate (borax) was added to the isomerization solution. Binding of tetrahydroxyborate ions to xylulose effectively reduces the concentration of xylulose and leads to increased xylose isomerization. The formation of tetrahydroxyborate ions and the enhancement in xylulose production resulting from the complexation was studied at two different bulk pH values. The addition of 0.05 M borax to the isomerization solution containing our co-immobilized enzyme pellets resulted in xylose to xylulose conversion as high as 86% under pH conditions that are suboptimal for XI activity. These initial findings, which can be optimized for industrial conditions, have significant potential for increasing the yield of ethanol from xylose in an SIF approach.