Effect of Initial Cell Concentration on Ethanol Production by Flocculent Saccharomyces cerevisiae with Xylose-Fermenting Ability

Different initial cell concentrations of a recombinant flocculent Saccharomyces cerevisiae MA-R4 were evaluated for their effects on xylose fermentation and glucose–xylose cofermentation. A high initial cell concentration greatly increased both the substrate utilization and ethanol production rates. During xylose fermentation, the highest rates of xylose consumption (2.58 g/L h) and ethanol production (0.83 g/L h) were obtained at an initial cell concentration of 13.1 g/L. During cofermentation, the highest rates of glucose consumption (14.4 g/L h), xylose consumption (2.79 g/L h), and ethanol production (6.68 g/L h) were obtained at an initial cell concentration of 12.7 g/L. However, a high initial cell density had no positive effect on the maximum ethanol concentration and ethanol yield mainly due to the increased amount of by-products including xylitol. The ethanol yield remained almost constant (0.34 g/g) throughout xylose fermentation (initial cell concentration range, 1.81–13.1 g/L), while it was slightly lower at high initial cell concentrations (9.87 and 12.7 g/L) during cofermentation. The determination of the appropriate initial cell concentration is necessary for the improvement of substrate utilization and ethanol yield.     

Characterization of a Recombinant Flocculent Saccharomyces cerevisiae Strain That Co-Ferments Glucose and Xylose: II. Influence of pH and Acetic Acid on Ethanol Production

The inhibitory effects of pH and acetic acid on the co-fermentation of glucose and xylose in complex medium by recombinant flocculent Saccharomyces cerevisiae MA-R4 were evaluated. In the absence of acetic acid, the fermentation performance of strain MA-R4 was similar between pH?4.0?C6.0, but was negatively affected at pH?2.5. The addition of acetic acid to batch cultures resulted in negligible inhibition of several fermentation parameters at pH?6.0, whereas the interactive inhibition of pH and acetic acid on the maximum cell and ethanol concentrations, and rates of sugar consumption and ethanol production were observed at pH levels below 5.4. The inhibitory effect of acetic acid was particularly marked for the consumption rate of xylose, as compared with that of glucose. With increasing initial acetic acid concentration, the ethanol yield slightly increased at pH?5.4 and 6.0, but decreased at pH values lower than 4.7. Notably, ethanol production was nearly completely inhibited under low pH (4.0) and high acetic acid (150?C200?mM) conditions. Together, these results indicate that the inhibitory effects of acetic acid and pH on ethanol fermentation by MA-R4 are highly synergistic, although the inhibition can be reduced by increasing the medium pH.     

Effect of Fermentation Conditions on the Flocculation of Recombinant Saccharomyces cerevisiae Capable of Co-fermenting Glucose and Xylose

Flocculation is a desirable property in industrial yeasts and is particularly important in the fuel ethanol industry because it provides a simple and cost-free way to separate yeast cells from fermentation products. In the present study, the effect of pH and lignocellulose-derived sugars on yeast flocculation was investigated using a flocculent Saccharomyces cerevisiae, MA-R4, which has been recombinantly engineered to simultaneously co-ferment glucose and xylose to ethanol with high productivity. The flocculation level of MA-R4 dramatically decreased at pH values below 3.0 during co-fermentation of glucose and xylose. Sedimentation and microscopic observation revealed that flocculation was induced in MA-R4 when it fermented glucose, a glucose/xylose mixture, or mannose, whereas attempts to ferment xylose, galactose, and arabinose led to the loss of flocculation. MA-R4 fermented xylose and galactose more slowly than glucose and mannose. Therefore, the various flocculation behaviors shown by MA-R4 should be useful in the control of ethanol fermentation processes.     

Efficient Non-sterilized Fermentation of Biomass-Derived Xylose to Lactic Acid by a Thermotolerant Bacillus coagulans NL01

Xylose is the major pentose and the second most abundant sugar in lignocellulosic feedstock. Its efficient utilization is regarded as a technical barrier to the commercial production of bulk chemicals from lignocellulosic biomass. This work aimed at evaluating the lactic acid production from the biomass-derived xylose using non-sterilized fermentation by Bacillus coagulans NL01. A maximum lactic acid concentration of about 75 g/L was achieved from xylose of 100 g/L after 72 h batch fermentation. Acetic acid and levulinic acid were identified as important inhibitors in xylose fermentation, which markedly reduced lactic acid productivity at 15 and 1.0 g/L, respectively. But low concentrations of formic acid (<2 g/L) exerted a stimulating effect on the lactic acid production. When prehydrolysate containing total 25.45 g/L monosaccharide was fermented with B. coagulans NL01, the same preference for glucose, xylose, and arabinose was observed and18.2 g/L lactic acid was obtained after 48 h fermentation. These results proved that B. coagulans NL01 was potentially well-suited for producing lactic acid from underutilized xylose-rich prehydrolysates.     

Fermentation kinetics of ethanol production from glucose and xylose by recombinant Saccharomyces 1400(pLNH33)

Fermentation kinetics of ethanol production from glucose, xylose, and their mixtures using a recombinant Saccharomyces 1400 (pLNH33) are reported. Single-substrate kinetics indicate that the specific growth rate of the yeast and the specific ethanol productivity on glucose as the substrate was greater than on xylose as a substrate. Ethanol yields from glucose and xylose fermentation were typically 95 and 80% of the theoretical yield, respectively. The effect of ethanol inhibition is more pronounced for xylose fermentation than for glucose fermentation. Studies on glucose-xylose mixtures indicate that the recombinant yeast co-ferments glucose and xylose. Fermentation of a 52.8 g/L glucose and 56.3 g/L xylose mixture gave an ethanol concentration of 47.9 g/L after 36 h. Based on a theoretical yield of 0.51 g ethanol/g sugars, the ethanol yield from this experiment (for data up to 24 h) was calculated to be 0.46 g ethanol/g sugar or 90% of the theoretical yield. The specific growth rate of the yeast on glucose-xylose mixtures was found to lie between the specific growth rate on glucose and the specific growth rate on xylose. Kinetic studies were used to develop a fermentation model incorporating the effects of substrate inhibition, product inhibition, and inoculum size. Good agreements were obtained between model predictions and experimental data from batch fermentation of glucose, xylose, and their mixtures.     

Improvement of Solvent Production from Xylose Mother Liquor by Engineering the Xylose Metabolic Pathway in Clostridium acetobutylicum EA 2018

Xylose mother liquor (XML) is a by-product of xylose production through acid hydrolysis from corncobs, which can be used potentially for alternative fermentation feedstock. Sixteen Clostridia including 13 wild-type, 1 industrial strain, and 2 genetically engineered strains were screened in XML, among which the industrial strain Clostridium acetobutylicum EA 2018 showed the highest titer of solvents (12.7 g/L) among non-genetic populations, whereas only 40 % of the xylose was consumed. An engineered strain (2018glcG-TBA) obtained by combination of glcG disruption and expression of the d-xylose proton-symporter, d-xylose isomerase, and xylulokinase was able to completely utilize glucose and l-arabinose, and 88 % xylose in XML. The 2018glcG-TBA produced total solvents up to 21 g/L with a 50 % enhancement of total solvent yield (0.33 g/g sugar) compared to that of EA 2018 (0.21 g/g sugar) in XML. This XML-based acetone–butanol–ethanol fermentation using recombinant 2018glcG-TBA was estimated to be economically promising for future production of solvents.     

Fermentation of xylose into acetic acid by Clostridium thermoaceticum

For optimum fermentation, fermenting xylose into acetic acid by Clostridium thermoaceticum (ATCC 49707) requires adaptation of the strain to xylose medium. Exposed to a mixture of glucose and xylose, it preferentially consumesxylose over glucose. The initial concentration of xylose in the medium affects the final concentration and the yield of acetic acid. Batch fermentation of 20 g/L of xylose with 5g/L of yeast extract as the nitrogen source results in a maximum acetate concentration of 15.2 g/L and yield of 0.76 g of acid/g of xylose. Corn steep liquor (CLS) is a good substitute for yeast extract and results in similar fermentation profiles. The organism consumes fructose, xylose, and glucose from a mixture of sugars in batch fermentation. Arabinose, mannose, and galactose are consumed only slightly. This organism loses viability on fed-batch operation, even with supplementation of all the required nutrients. In fed-batch fermentation with CSL supplementation, d-xylulose (an intermediate in the xylose metabolic pathway) accumulates in large quantities.     

Production of Xylose from Meranti Wood Sawdust by Dilute Acid Hydrolysis

Xylitol production by bioconversion of xylose can be economically interesting if the raw material can be recovered from a cheap lignocellulosic biomass (LCB). Meranti wood sawdust (MWS) is a renewable and low-cost LCB that can be used as a promising and economic source of xylose, a starting raw material for the manufacture of several specialty chemicals, especially xylitol. This study aimed to optimize the hydrolysis process of MWS and to determine the influence of temperature, H₂SO₄ concentration, and residence time on xylose release and on by-product formation (glucose, arabinose, acetic acid, furfural, hydroxymethylfurfural (HMF), and lignin degradation products (LDPs)). Batch hydrolysis was conducted under various operating conditions, and response surface methodology was adopted to achieve the highest xylose yield. Xylose production was highly affected by temperature, acid concentration, and residence time. The optimum temperature, acid concentration, and time were determined to be 124 °C, 3.26 %, and 80 min, respectively. Under these optimum conditions, xylose yield and selectivity were attained at 90.6 % and 4.05 g/g, respectively.     

Ethanol Production Using Whole Plant Biomass of Jerusalem Artichoke by Kluyveromyces marxianus CBS1555

Jerusalem artichoke is a low-requirement sugar crop containing cellulose and hemicellulose in the stalk and a high content of inulin in the tuber. However, the lignocellulosic component in Jerusalem artichoke stalk reduces the fermentability of the whole plant for efficient bioethanol production. In this study, Jerusalem artichoke stalk was pretreated sequentially with dilute acid and alkali, and then hydrolyzed enzymatically. During enzymatic hydrolysis, approximately 88 % of the glucan and xylan were converted to glucose and xylose, respectively. Batch and fed-batch simultaneous saccharification and fermentation of both pretreated stalk and tuber by Kluyveromyces marxianus CBS1555 were effectively performed, yielding 29.1 and 70.2 g/L ethanol, respectively. In fed-batch fermentation, ethanol productivity was 0.255 g ethanol per gram of dry Jerusalem artichoke biomass, or 0.361 g ethanol per gram of glucose, with a 0.924 g/L/h ethanol productivity. These results show that combining the tuber and the stalk hydrolysate is a useful strategy for whole biomass utilization in effective bioethanol fermentation from Jerusalem artichoke.     

Improved Ethanol and Reduced Xylitol Production from Glucose and Xylose Mixtures by the Mutant Strain of <Emphasis Type="Italic">Candida shehatae</Emphasis> ATCC 22984

A mutant Cs3512, which showed better fermentation of xylose and the mixtures of xylose and glucose, was obtained through mutation of Candida shehatae ATCC 22984 and screening with a medium containing antimycin A and TTC (2,3,5-triphenyltetrazolium chloride). Cs3512 produced 44.4 g/l of ethanol from 121.3 g/l of xylose, which was 13% higher than that by ATCC 22984. At the same time, xylitol production was reduced by 38% to 10.2 g/l from 16.3 g/l by ATCC 22984. Cs3512 also showed 8% increase in ethanol yield from 0.39 to 0.42 g/g comparing to ATCC 22984 when fermenting the sugar mixture composed of 52.9 g/l glucose and 21.2 g/l xylose. When Cs3512 was used in the simultaneous saccharification and fermentation of lime pretreated rice straw via CaCCO (calcium capturing by carbonation) process, it produced ethanol at 77% of the theoretical yield. The results imply that Cs3512 is a potential non-recombinant yeast strain for ethanol production from lignocellulosic biomass.     

Evaluation of Ethanol Production from Corncob Using Scheffersomyces (Pichia) stipitis CBS 6054 by Volumetric Scale-up

In scale-up, the potential of ethanol production by dilute sulfuric acid pretreatment using corncob was investigated. Pretreatments were performed at 170 °C with various acid concentrations ranging from 0% to 1.656% based on oven dry weight. Following pretreatment, pretreated biomass yield ranged from 59% to 67%. More than 90% of xylan was removed at 0.828% of sulfuric acid. At same pretreatment condition, the highest glucose yield obtained from pretreated biomass by enzymatic hydrolysis was about 76%, based on a glucan content of 37/100 g. In hydrolysate obtained by pretreatment, glucose concentration was low, while xylose concentration was significantly increased above 0.368% of sulfuric acid. At 1.656% of sulfuric acid, xylose and glucose concentration was highest. In subsequent, fermentation with hydrolysate, maximal ethanol yield was attained after 24 h with 0.368% of sulfuric acid. The fermentation efficiency of hydrolysate obtained by enzymatic hydrolysis reached a maximum of 75% at an acid charge of 0.368%.     

Fermentation performance assessment of a genomically integrated xylose-utilizing recombinant of Zymomonas mobilis 39676

In pH-controlled batch fermentations with pure sugar synthetic hardwood hemicellulose (1% [w/v] glucose and 4% xylose) and corn stover hydrolysate (8% glucose and 3.5% xylose) lacking acetic acid, the xyloseutilizing, tetracycline (Tc)-sensitive, genomically integrated variant of Zymomonas mobilis ATCC 39676 (designated strain C25) exhibited growth and fermentation performance that was inferior to National Renewable Energy Laboratory's first-generation, Tc-resistant, plasmid-bearing Zymomonas recombinants. With C25, xylose fermentation following glucose exhaustion wasmarkellyslower, and the ethanol yield (based on sugars consumed) was lower, owing primarily to an increase in lactic acid formation. There was an apparent increased sensitivity to acetic acid inhibition with C25 compared with recombinants 39676:pZB4L, CP4:pZB5, and ZM4:pZB5. However, strain C25 performed well in continous ferm entation with nutrient-rich synthetic corn stover medium over the dilution range 0.03–0.06/h, with a maximum provess ethanol yield at D=0.03/h of 0.46 g/g and a maximum ethanol productivity of 3 g/(L·h). With 0.35% (w/v) acetic acid in the medium, the process yield at D=0.04/h dropped to 0.32 g/g, and the maximum productivity decreased by 50% to 1.5 g/(L·h). Under the same operating conditions, rec Zm Zm 4:pZB5 performed better; however, the medium contained 20 mg/L of Tc to constantly maintain selective pressure. The absence of any need for antibiotics and antiboitic resistance genes makes the chromosomal integrant C25 more com patible with current regulatory specifications for biocatalysts in large-scale commercial operations.     

Improving fermentation performance of recombinant zymomonas in acetic acid-containing media

In the production of ethanol from lignocellulosic biomass, the hydrolysis of the acetylated pentosans in hemicellulose during pretreatment produces acetic acid in the prehydrolysate. The National Renewable Energy Laboratory (NREL) is currently investigating a simultaneous saccharification and cofermentation (SSCF) process that uses a proprietary metabolically engineered strain ofZymomonas mobilis that can coferment glucose and xylose. Acetic acid toxicity represents a major limitation to bioconversion, and cost-effective means of reducing the inhibitory effects of acetic acid represent an opportunity for significant increased productivity and reduced cost of producing fermentation fuel ethanol from biomass. In this study, the fermentation performance of recombinant Z.mobilis 39676:pZB4L, using a synthetic hardwood prehydrolysate containing 1% (w/v) yeast extract, 0.2% KH₂PO₄, 4% (w/v) xylose, and 0.8% (w/v) glucose, with varying amounts of acetic acid was examine. To minimize the concentration of the inhibitory undissociated form of acetic acid, the pH was controlled at 6.0. The final cell mass concentration decreased linearly with increasing level of acetic acid over the range 0-0.75% (w/v), with a 50% reduction at about 0.5% (w/v) acetic acid. The conversion efficiency was relatively unaffected, decreasing from 98 to 92%. In the absence of acetic acid, batch fermentations were complete at 24 h. In a batch fermentation with 0.75% (w/v) acetic acid, about two-thirds of the xylose was not metabolized after 48 h. In batch fermentations with 0.75% (w/v) acetic acid, increasing the initial glucose concentration did not have an enhancing effect on the rate of xylose fermentation. However, nearly complete xylose fermentation was achieved in 48 h when the bioreactor was fed glucose. In the fed-batch system, the rate of glucose feeding (0.5 g/h) was designed to simulate the rate of cellulolytic digestion that had been observed in a modeled SSCF process with recombinant Zymomonas. In the absence of acetic acid, this rate of glucose feeding did not inhibit xylose utilization. It is concluded that the inhibitory effect of acetic acid on xylose utilization in the SSCF biomass-to-ethanol process will be partially ameliorated because of the simultaneous saccharification of the cellulose.

     

Ethanol production from glucose and xylose by immobilized Zymomonas mobilis CP4 (pZB5)

Fermentation of glucose-xylose mixtures to ethanol was investigated in batch and continuous experiments using immobilized recombinant Zymomonas mobilis CP4(pZB5). This microorganism was immobilized by entrapment in κ-carrageenan beads having a diameter of 1.5–2.5 mm. Batch experiments showed that the immobilized cells cofermented glucose and xylose to ethanol and that the presence of glucose improved the xylose utilization rate. Batch fermentation of rice straw hydrolysate containing 76 g/L of glucose and 33.8 g/L of xylose gave an ethanol concentration of 44.3 g/L after 24 h, corresponding to a yield of 0.46 g of ethanol/g of sugars. Comparable results were achieved with a synthetic sugar control. Continuous fermentation experiments were performed in a laboratory-scale fluidized-bed bioreactor (FBR). Glucose-xylose feed mixtures were pumped through the FBR at residence times of 2–4 h. Glucose conversion to ethanol was maintained above 98% in all experiments. Xylose conversion to ethanol was highest at 91.5% for a feed containing 50 g/L of glucose and 13 g/L of xylose at a dilution rate of 0.24/h. The xylose conversion to ethanol decreased with increasing feed xylose concentration, dilution rate, and age of the immobilized cells. Volumetric ethanol productivities in the range of 6.5–15.3 g/L·h were obtained. The improved productivities achieved in the FBR compared to other bioreactor systems can help in reducing the production costs of fuel ethanol from lignocellulosic sugars. This article has been authored by a contractor of the US go vernment under contract DE-AC05-96OR22464. Accordingly, the US government retains a nonexclusive, royaltyfree license to publish or reproduce the published form of the contribution, or allow others to do so, for US government purposes.     

Characterization of a high-productivity recombinant strain of Zymomonas mobilis for ethanol production from glucose/xylose mixtures

The fermentation characteristics of a recombinant strain of Zymomonas mobilis ZM4(pZB5) capable of converting both glucose and xylose to ethanol have been further investigated. Previous studies have shown that the strain ZM4(pZB5) was capable of converting a mixture o 65 g/L of glucose and 65 g/L of xylose to 62 g/L of ethanol in 48 h with an overall yield of 0.46 g/g. Higher sugar concentrations (e.g., 75/75 g/L) resulted in incomplete xylose utilization (80 h). In the present study, further kinetic evaluations at high sugar levels are reported. Acetate inhibition studies and evaluation of temperature and pH effects indicated increased maximum specific uptake rates of glucose and xylose under stressed conditions with increased metabolic uncoupling. A high-productivity system was developed that involved a membrane bioreactor with cell recycling. At sugar concentrations of approx 50/50 g/L of glucose/xylose, an ethanol concentration of 50 g/L, an ethanol productivity of approx 5 g/(L·h), and a yield (Y _p/s) of 0.50 g/g were achieved. Decreases in cell viability were found in this system after attainment of an initial steady state (40–60 h); a slow bleed of concentrated cells may be required to overcome this problem.     

The effect of lactic acid on fuel ethanol production byZymomonas

Efficient utilization of the pentosan fraction of hemicellulose from lignocellulosic feedstocks offers an opportunity to increase the yield and to reduce the cost of producing fuel ethanol. During prehydrolysis (acid hydrolysis or autohydrolysis of hemicellulose), acetic acid is formed as a consequence of the deacetylation of the acetylated moiety of hemicellulose. Recombinant Escherichia coli B (ATCC 11303), carrying the plasmid pLO1297 with pyruvate decarboxylase and alcohol dehydrogenase II genes from Zymomonas mobilis (CP4), converts xylose to ethanol with a product yield that approaches theoretical maximum. Although other pentose-utilizing microorganisms are inhibited by acetic acid, the recombinant E. coli displays a high tolerance for acetic acid. In xylose fermentations with a synthetic medium (Luria broth), where the pH was controlled at 7, neither yield nor productivity was affected by the addition of 10.7 g/L acetic acid. Nutrient-supplemented, hardwood (aspen) hemicellulose hydrolysate (40.7 g/L xylose) was completely fermented to ethanol (16.3 g/L) in 98 h. When the acetic acid concentration was reduced from 5.6 to 0.8 g/L, the fermentation time decreased to 58 h. Overliming, with Ca(OH)₂ to pH 10, followed by neutralization to pH 7 with sulfuric acid and removal of insolubles, resulted in a twofold increase in volumetric productivity. The maximum productivity was 0.93 g/L/h. The xylose-to-ethanol conversion efficiency and productivity in Ca(OH)₂-treated hardwood prehydrolysate, fortified with only mineral salts, were 94% and 0.26 g/L/h, respectively. The recombinant E. coli exhibits a xylose-to-ethanol conversion efficiency that is superior to that of other pentose-utilizing yeasts currently being investigated for the production of fuel ethanol from lignocellulosic materials.     

Optimizing Dilute-Acid Pretreatment of Rapeseed Straw for Extraction of Hemicellulose

Biological conversion of biomass into fuels and chemicals requires hydrolysis of the polysaccharide fraction into monomeric sugars prior to fermentation. Hydrolysis can be performed enzymatically or with mineral acids. In this study, dilute sulfuric acid was used as a catalyst for the pretreatment of rapeseed straw. The purpose of this study is to optimize the pretreatment process in a 15-mL bomb tube reactor and investigate the effects of the acid concentration, temperature, and reaction time. These parameters influence hemicellulose removal and production of sugars (xylose, glucose, and arabinose) in the hydrolyzate as well as the formation of by-products (furfural, 5-hydroxymethylfurfural, and acetic acid). Statistical analysis was based on a model composition corresponding to a 3³ orthogonal factorial design and employed the response surface methodology to optimize the pretreatment conditions, aiming to attain maximum xylan, mannan, and galactan (XMG) extraction from hemicellulose of rapeseed straw. The obtained optimum conditions were: H₂SO₄ concentration of 1.76% and temperature of 152.6 °C with a reaction time of 21 min. Under these optimal conditions, 85.5% of the total sugar was recovered after acid hydrolysis (78.9% XMG and 6.6% glucan). The hydrolyzate contained 1.60 g/L glucose, 0.61 g/L arabinose, 10.49 g/L xylose, mannose, and galactose, 0.39 g/L cellobiose, 0.94 g/L fructose, 0.02 g/L 1,6-anhydro-glucose, 1.17 g/L formic acid, 2.94 g/L acetic acid, 0.04 g/L levulinic acid, 0.04 g/L 5-hydroxymethylfurfural, and 0.98 g/L furfural.     

Comparative ethanol productivities of different Zymomonas recombinants fermenting oat hull hydrolysate

Iogen Corporation of Ottawa, Canada, has recently built a 50 t/d biomass-to-ethanol demonstration plant adjacent to its enzyme production facility. Iogen has partnered with the University of Toronto to test the C6/C5 cofermentation performance characteristics of National Renewable Energy Laboratory's metabolically engineered Zymomonas mobilis using its biomass hydrolysates. In this study, the biomass feedstock was an agricultural waste, namely oat hulls, which was hydrolyzed in a proprietary two-stage process involving pretreatment with dilute sulfuric acid at 200–250°C, followed by cellulase hydrolysis. The oat hull hydrolysate (OHH) contained glucose, xylose, and arabinose in a mass ratio of about 8:3:0.5. Fermentation media, prepared from diluted hydrolysate, were nutritionally amended with 2.5 mL/L of corn steep liquor (50% solids) and 1.2 g/L of diammonium phosphate. The estimated cost for large-scale ethanol production using this minimal level of nutrient supplementation was 4.4c/gal of ethanol. This work examined the growth and fermentation performance of xyloseutilizing, tetracycline-resistant, plasmid-bearing, patented, recombinant Z. mobilis cultures: CP4:pZB5, ZM4:pZB5, 39676:pZB4L, and a hardwood prehydrolysate-adapted variant of 39676:pZB4L (designated asthe “adapted” strain). In pH-stat batch fermentations with unconditioned OHH containing 6% (w/v) glucose, 3% xylose, and 0.75% acetic acid, rec Zm ZM4:pZB5 gave the best performance with a fermentation time of 30h, followed by CP4:pZB5 at 48h, with corresponding volumetric productivities of 1.4 and 0.89 g/(L·h), respectively. Based on the available glucose and xylose, the process ethanol yield for both strains was 0.47 g/g (92% conversion efficiency). At 48 h, the process yield for rec Zm 39676:pZB4L and the adapted strain was 0.32 and 0.34 g/g, respectively. None of the test strains was able to fermentarabinose. Acetic acid tolerance appeared to be a major determining factor in cofermentation performance.     

The combined effects of acetic acid, formic acid, and hydroquinone on Debaryomyces hansenii physiology

The combined effects of inhibitors present in lignocellulosic hydrolysates was studied using a multivariate statistical approach. Acetic acid (0–6 g/L), formic acid (0–4.6 g/L) and hydroquinone (0–3 g/L) were tested as model inhibitors in synthetic media containing a mixture of glucose, xylose, and arabinose simulating concentrated hemicellulosic hydrolysates. Inhibitors were consumed sequentially (acetic acid, formic acid, and hydroquinone), alongside to the monosaccharides (glucose, xylose, and arabinose). Xylitol was always the main metabolic product. Additionally, glycerol, ethanol, and arabitol were also obtained. The inhibitory action of acetic acid on growth, on glucose consumption and on all product formation rates was found to be significant (p≤0.05), as well as formic acid inhibition on xylose consumption and biomass production. Hydroquinone negatively affected biomass productivity and yield, but it significantly increased xylose consumption and xylitol productivity. Hydroquinone interactions, either with acetic or formic acid or with both, are also statistically signficant. Hydroquinone seems to partially lessen the acetic acid and amplify formic acid effects. The results clearly indicate that the interaction effects play an important role on the xylitol bioprocess.     

Cofermentation of glucose,xylose, and arabinose by mixed cultures of two genetically engineeredZymomonas mobilis strains

Cofermentation of xylose and arabinose, in addition to glucose, is critical for complete bioconversion of lignocellulosic biomass, such as agricultural residues and herbaceous energy crops, to ethanol. A factorial design experiment was used to evaluate the cofermentation of glucose, xylose, and arabinose with mixed cultures of two genetically engineeredZymomonas mobilis strains (one ferments xylose and the other arabinose). The pH range studied was 5.0-6.0, and the temperature range was 30-37°C The individual sugar concentrations used were 30 g/L glucose, 30 g/L xylose, and 20 g/L arabinose. The optimal cofermentation conditions obtained by data analysis, using Design Expert software, were pH 5.85 and temperature 31.5°C. The cofermentation process yield at optimal conditions was 72.5% of theoritical maximum. The results showed that neither the arabinose strain nor arabinose affected the performance of the xylose strain; however, both xylose strain and xylose had a significant effect on the performance of the arabinose strain. Although cofermentation of all three sugars is achieved by the mixed cultures, there is a preferential order of sugar utilization. Glucose is used rapidly, then xylose, followed by arabinose.