Novel fabrication and catalytic application of poly(ethylenimine)-stabilized gold–silver alloy nanoparticles

Novel synthesis of amine-stabilized Au–Ag alloy nanoparticles with controlled composition has been devised using poly(ethylenimine) (PEI) as a reducing and a stabilizing agent simultaneously. The composition of Au–Ag alloy nanoparticles was readily controlled by varying the initial relative amount of HAuCl₄ and AgNO₃. Due to the presence of abundant amine functional groups in PEI, which could act as the dissolving ligand for AgCl, the precipitation problem of Ag⁺ in the presence of Cl⁻ from the gold salt was avoided. On this basis, the relatively high concentrations of HAuCl₄ and AgNO₃ salts were used for the fabrication of Au–Ag alloy nanoparticles. The PEI thus plays triple roles in this study that include the co-reducing agents for HAuCl₄ and AgNO₃, the stabilizing agents for Au–Ag alloy nanoparticles, and even the dissolving agents for AgCl. As a novel material for use in catalysis, the Au–Ag alloy nanoparticles including pure Au and Ag samples were exploited as catalysts for the reduction of 4-nitrophenol in the presence of NaBH₄. As the Au content was increased in the Au–Ag alloy nanoparticles, the rate constant of the reduction was exponentially increased from pure Ag to pure Au.     

Differential mobility analysis of nanoparticles generated by laser vaporization and controlled condensation (LVCC)

Silicon and iron aluminide (FeAl) nanoparticles were synthesized by a laser vaporization controlled condensation (LVCC) method. The particles generated by the laser ablation of solid targets were transported and deposited in the presence of well-defined thermal and electric field in a newly designed flow-type LVCC chamber. The deposition process of nanoparticles was controlled by the balance of the external forces; i.e., gas flow, thermophoretic and electrostatic forces. The size distributions of generated nanoparticles were analyzed using a low-pressure differential mobility analyzer (LP-DMA). The effect of synthesis condition on the size distribution was analyzed by changing the pressure of the carrier gas (20–200 Torr), the temperature gradient in the LVCC chamber (ΔT=0–190°C) and the electric field applied between the LVCC chamber plates (E=0–3000 V/m). It was found that electrostatic field was effective to selectively deposit small size nanoparticles (about 10 nm) with expelling large droplet-like particles.     

Synthesis of composite gold/tin-oxide nanoparticles by nano-soldering

Composite Au–SnO₂ nanoparticles (NPs) are synthesized by nano-soldering of pure Au and SnO₂ NPs. The multi-step process involves synthesis of pure Au and SnO₂ NPs separately by nanosecond pulse laser ablation of pure gold and pure tin targets in deionized water and post-ablation laser heating of mixed solution of Au colloidal and SnO₂ colloidal to form nanocomposite. Transmission Electron Microscopy (TEM) and High-Resolution Transmission Electron Microscopy (HRTEM) were used to study the effect of laser irradiation time on morphology of the composite Au–SnO₂ NPs. The spherical particles of 4 nm mean size were obtained for 5 min of post-laser heating. Increased mean size and elongated particles were observed on further laser heating. UV–vis spectra of Au–SnO₂ nanocomposites show red shift in the plasmon resonance absorption peak and line shape broadening with respect to pure Au NPs. The negative binding energy shift of Au 4f_7/2 peak observed in X-ray Photoelectron Spectra (XPS) indicates charge transfer in the nano-soldered Au–SnO₂ between gold and tin oxide and formation of soldered nanocomposite.     

Sonochemically synthesized core-shell structured Au–Pd nanoparticles supported on γ-Fe2O3 particles

A sample of Au–Pd bimetallic nanoparticles supported on γ-Fe₂O₃ was synthesized in a sonochemically one-pot process. The structural analyses of the synthesized sample were performed by the techniques of X-ray Absorption Fine Structure (XAFS), X-ray Diffraction (XRD), Transmission Electron Microscopy (TEM) and UV–vis spectrometry. Results indicated that the synthesized sample formed a core-shell structure in which a gold core was surrounded by a thin palladium shell. The reaction rate constant for the hydrogenation of cyclohexene of the present sample showed higher value than that of Pd nanoparticles supported on γ-Fe₂O₃ and core-shell structured Au–Pd nanoparticles supported on SiO₂. The present sample is a promising catalyst material which has a high catalytic activity.     

Surface plasmon resonance response of Au–WO3?x composite films

Surface plasmon resonance of metal–dielectric composite thin films formed by noble metal nanoparticles embedded in a dielectric matrix offers a high degree of flexibility and enables many applications such as surface enhanced spectroscopes, and biological and chemical sensing. In this article, Au–WO_3−x composite films of various Au contents and thicknesses were prepared by the pulsed laser deposition technique, and their SPR responses were measured in the Kreschmann geometry, using a polarized light beam at 640 nm wavelength. Theoretical calculation of SPR responses based on the Bruggeman or Maxwell–Garnett model with the MacLeod general characteristic matrix method is in obvious discrepancy with experimental measurements but it is able to predict the trend in term of the dependence of SPR responses on Au content and thickness of the Au–WO_3−x films. The SPR responses of the Au–WO_3−x films when exposed to NO gas molecules were measured and the preliminary results indicated that gas sensing using the SPR responses of metal–dielectric composite films is feasible.     

Synthesis of nanostructured lean-NO x catalysts by direct laser deposition of monometallic Pt-, Rh- and bimetallic PtRh-nanoparticles on SiO2 support

Monometallic Pt and Rh and bimetallic PtRh catalysts with a highly dispersed noble metal weight loading of ca. 1 wt% were produced via the direct deposition of nanoparticles on different SiO₂ supports by means of pulsed ultra-violet (248 nm) excimer laser ablation of Pt, Rh bulk metal and PtRh alloy targets. Backscattered electron microscopy (BSE), energy dispersive X-ray spectroscopy (EDX), and transmission electron microscopy (TEM) were employed to characterize the deposited nanoparticles, which were found to exhibit narrow size distribution centred around 2.5 nm. The catalytic activities for lean NO _x reduction of the monometallic and bimetallic catalyst samples were investigated in a flow reactor setup in the temperature range 100–400°C using a test gas mixture representative of oxygen rich diesel engine exhaust gas. For comparison a Rh/SiO₂ reference catalyst prepared by a conventional impregnation method was also tested. Further experiments were performed in which PtRh nanoparticles were deposited on a Rh/SiO₂ reference catalyst sample to study the possibility for controlled modification of its activity. The catalytic activity measurements revealed that among the samples solely prepared by laser deposition the PtRh–SiO₂ nanoparticle catalyst showed the highest activity for NO _x reduction at low temperatures 100–300°C. In addition, it could be demonstrated that the initially low NO _x reduction activity and the N₂ selectivity of the Rh/SiO₂ reference catalyst sample for temperatures below 250°C can be enhanced by post laser deposition of PtRh nanoparticles.     

Cu<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>Ni<Subscript>1−<Emphasis Type="Italic">x</Emphasis></Subscript> alloy nanoparticles embedded SiO<Subscript>2</Subscript> films: synthesis and structure

Cu–Ni fcc alloy nanoparticles (NPs) of tunable atomic ratios were generated in SiO₂ films. The films were prepared using the Cu(NO₃)₂ and Ni(NO₃)₂ co-doped inorganic–organic hybrid silica sols by single dipping. Transparent, crack-free, glassy SiO₂ films of 310 ± 10 nm in thickness embedded with high mol percent of Cu–Ni alloy NPs were yielded after annealing at 750 °C in 10% H₂-90% Ar atmosphere. Nominal compositions of the films were 20 mol% (Cu–Ni)-80 mol% SiO₂. Optical spectral study of the heat-treated films showed disappearance of Cu plasmon bands due to Cu–Ni alloy formation. Grazing incidence X-ray diffraction (GIXRD) studies revealed the formation of Cu–Ni alloy (2:1, 1:1 and 1:2) NPs inside the SiO₂ film. GIXRD showed a systematic shifting of the diffraction peaks with respect to the fcc Cu–Ni alloy composition, maintaining the nominal ratios. Transmission electron microscopy (TEM) studies of the representative Cu_0.5Ni_0.5-doped film showed existence of homogeneously dispersed Cu–Ni alloy NPs of average size 6.35 nm inside the SiO₂ matrix. The energy dispersive X-ray scattering (EDX) analysis of the individual NPs using the nano-probe (scanning TEM mode) confirmed the presence of both the Cu and Ni with the desired atomic ratio.     

Mono and bimetallic nanoparticles of gold,silver and palladium-catalyzed NADH oxidation-coupled reduction of Eosin-Y

Abstract  

Mono metallic (Au, Ag, Pd) and bimetallic (Au–Ag, Ag–Pd, Au–Pd) with 1:1 mol stoichiometry, nanoparticles are synthesized using one-pot, temperature controlled chemical method using cetyltrimethylammonium bromide (CTAB) as the capping agent. The particle sizes (Au = 5.6, Ag = 5.0, Pd = 6.0, Au–Ag = 9.2, Ag–Pd = 9.6, Au–Pd = 9.4 nm) are characterized by UV–Vis, HRTEM, and XRD measurements, respectively. CTAB bindings onto mono and bimetallic nanoparticles are analyzed by FTIR spectra. The catalytic activities of mono and bimetallic nanoparticles are tested on the reaction between NADH oxidation and Eosin-Y reduction. The effects of base, pH, ionic strength, nature of mono and bimetallic catalysts are studied and the reaction conditions are optimized. Bimetallic nanoparticles exhibited better catalysis than the mono metallic nanoparticles, which may be due to the electronic effects of the core to shell metal atoms.     

Synthesis and photo physical properties of Au @ Ag (core @ shell) nanoparticles disperse in poly vinyl alcohol matrix

Synthesis of core @ shell (Au @ Ag) nanoparticle with varying silver composition has been carried out in aqueous poly vinyl alcohol (PVA) matrix. Core gold nanoparticle (~15 nm) has been synthesized through seed-mediated growth process. Synthesis of silver shell with increasing thickness (~1–5 nm) has been done by reducing Ag⁺ over the gold sol in the presence of mild reducing ascorbic acid. Characterization of Au @ Ag nanoparticles has been done by UV–Vis, High resolution transmission electron microscope (HRTEM) and energy dispersive X-ray (EDX) spectroscopic study. The blue shift of surface plasmon resonance (SPR) band with increasing mole fraction of silver has been interpreted due to dampening of core, i.e. Au SPR by Ag. The dependence of nonlinear optical response of spherical core @ shell nanoparticles has been investigated as a function of relative composition of each metal. Simulation of SPR extinction spectra based on quasi-static theory is done. A comparison of our experimental and the simulated extinction spectra using quasi-static theory of nanoshell suggests that our synthesized bimetallic particles have core @ shell structure rather than bimetallic alloy particles.     

Optical properties and ultrafast electron dynamics in gold–silver alloy and core–shell nanoparticles

Silver and gold are the two most popular metals used for many nanoparticle applications, such as surface enhanced Raman scattering or surface enhanced fluorescence, in which the local field enhancement associated with the excitation of the localized surface-plasmon–polariton resonance (SPR) is exploited. Therefore, tunability of the SPR over a wide energy range is required. For this purpose we have investigated core–shell nanoparticles composed of gold and silver with different shell thicknesses as well as the impact of alloying on these nanoparticles due to a tempering process. The nanoparticles were prepared by subsequent deposition of Au and Ag atoms or vice versa on quartz substrates followed by diffusion and nucleation. Their linear extinction spectra were measured as a function of shell thickness and annealing temperature. It turned out that different gold shell thicknesses on silver cores allow a tuning of the SPR position from 2.79 to 2.05 eV, but interestingly without a significant change on the extinction amplitude. Heating of core–shell nanoparticles up to only 540 K leads to the formation of alloy nanoparticles, accompanied by a back shift of the SPR to 2.60 eV. Calculations performed in quasi-static approximation describe the experimental results quite well and prove the structural assignments of the samples. In additional experiments, we applied the well-established persistent spectral hole burning technique to the alloy nanoparticles in order to determine the ultrafast dephasing time T ₂. We obtained a dephasing time of T ₂=(8.1±1.6) fs, in good agreement with the dephasing time of T _2,∞=8.9 fs, which is already included in the dielectric function of the bulk.     

Nanoparticle formation during laser ablation of metals at different pressures of surrounding noble gases

We demonstrate that the nanoparticle formation during laser ablation of metals by short (of a few tens of ps) laser pulses strongly depends on the concentration of surrounding gas. While, at vacuum conditions, nanoparticle formation shows very “sharp” atomic force microscope images of aggregated clusters, following with clear appearance of plasmon resonance on the absorption spectra of deposited films, an addition of gas particles starts to decrease the probability of cluster formation. This process shows a threshold for both helium (33 torr) and xenon (12 torr) above which no surface plasmon resonance and correspondingly no observable nanoparticles on the deposited surfaces were detected. The destruction of nanoparticle formation was attributed to the negative influence of surrounding gas particles on ablated particles aggregation.     

Plasmonics properties of trimetallic Al@Al2O3@Ag@Au and Al@Al2O3@AuAg nanostructures

Bimetallic and trimetallic nanoparticles have attracted significant attention in recent times due to their enhanced electrochemical and catalytic properties compared to monometallic nanoparticles. The numerical calculations using Mie theory has been carried out for three-layered metal nanoshell dielectric–metal–metal (DMM) system consisting of a particle with a dielectric core (Al@Al₂O₃), a middle metal Ag (Au) layer and an outer metal Au (Ag) shell. The results have been interpreted using plasmon hybridization theory. We have also prepared Al@Al₂O₃@Ag@Au and Al@Al₂O₃@AgAu triple-layered core–shell or alloy nanostructure by two-step laser ablation method and compared with calculated results. The synthesis involves temporal separations of Al, Ag, and Au deposition for step-by-step formation of triple-layered core–shell structure. To form Al@Ag nanoparticles, we ablated silver for 40 min in aluminium nanoparticle colloidal solution. As aluminium oxidizes easily in water to form alumina, the resulting structure is core–shell Al@Al₂O₃. The Al@Al₂O₃ particle acts as a seed for the incoming energetic silver particles for multilayered Al@Al₂O₃@Ag nanoparticles is formed. The silver target was then replaced by gold target and ablation was carried out for different ablation time using different laser energy for generation of Al@Al₂O₃@Ag@Au core–shell or Al@Al₂O₃@AgAu alloy. The formation of core–shell and alloy nanostructure was confirmed by UV–visible spectroscopy. The absorption spectra show shift in plasmon resonance peak of silver to gold in the range 400–520 nm with increasing ablation time suggesting formation of Ag–Au alloy in the presence of alumina particles in the solution.     

Photochemical synthesis of copper nanoparticles incorporated in poly(vinyl pyrrolidone)

The effect of the presence of poly(vinyl pyrrolidone) (PVP) on the copper nanoparticle formation, obtained by UV irradiation of ethanol solution of Cu(acac)₂ (acac = 2,4-pentanedionato), was investigated. At 254 nm, in conditions of light completely absorbed by complex, the PVP exhibited protective and stabilizing effects, as shown by the formation of a colloidal copper solution and by a block of the heterogeneous process, which leads to thin film formation on the quartz walls. The colloidal solution was tested for several months by plasmon position and it was found that it remained unaltered in inert atmosphere, but returned to the starting complex on contact with air. The PVP ability to control the particle size was investigated by carrying out photoreduction sensitized by Hacac at 254 and 300 nm, in the presence of PVP concentration varying from 0 to 0.2 M. In this range it was possible to obtain copper nanoparticles of dimensions decreasing from 30 to 4 nm. Besides this, the PVP (0.005–0.05 M) role as sensitizer was investigated by irradiating solutions of Cu(acac)₂ at 300 nm which is an inactive wavelength for copper reduction by direct light absorption. It was found that the PVP was an efficient sensitizer of the copper photoreduction. The nanoparticles were characterized by plasmon band, Trasmission Electron Microscope (TEM) as well as Dynamic Light Scattering (DSL) analysis. The overall results evidence the advantages of the PVP use in the nanoparticle copper formation through the photochemical technique such as the exclusive formation of colloidal copper, their size control, stable colloidal solution and complete return to the starting complex.     

Energy-filtered electron microscopy for imaging core–shell nanostructures

CuAg core–shell nanoparticles are synthesized by ultra-high vacuum thermal evaporation. We show on this system how the Energy-Filtered Transmission Electron Microscopy (EFTEM) technique allows one to improve the characterization by precisely pointing out the formation of core–shell arrangements in bimetallic nanoparticle assemblies. A criterion to measure the shell thickness from EFTEM images on unique core–shell nanoparticles is defined, that can be used for core–shell nanoparticles of any sizes, with shell thicknesses over 1 nm. It is based on the intensity variation along a line drawn across a core–shell nanoparticle on a EFTEM image. This criterion has been validated by a close comparison of the shell thickness measurements performed in this work and the ones obtained by acoustic micro-Raman spectroscopy. Using this criterion, we report a strong correlation between the size of the Cu cores and the formation of the core–shell arrangements in the nanoparticle assembly studied in this work. The influence of the Cu core shape is also evidenced. The characterisation of such systems using High Resolution TEM (HRTEM) is also discussed.     

Preparation of Pt–CeO2/MWNT nano-composites by reverse micellar method for methanol oxidation

We report the preparation of Pt–CeO₂ nanoparticles on the multi-walled carbon nanotubes (MWNTs) by a reverse micellar method. Transmission electron microscopy (TEM) analysis indicated that well-dispersed small Pt–CeO₂ nanoparticles were formed on the MWCNTs. X-ray diffraction (XRD) analysis confirmed the formation of the Pt–CeO₂ nanoparticles on the MWNTs. Cyclic voltammetry (CV) results demonstrated that the Pt–CeO₂/MWNT exhibited a higher methanol oxidation than did the Pt/MWNT catalyst. The CO stripping test showed that CeO₂ can make CO stripped at a lower potential, which is helpful for CO and methanol electro-oxidation.     

Nanoparticle-Coated Silicon Nanowires

The synthesis of silicon nanowires that are densely coated with silicon nanoparticles is reported. These structures were produced in a two-step process, using a method known as hypersonic plasma particle deposition. In the first step, a Ti–Si nanoparticle film was deposited. In the second step the Ti-source was switched off, and nanoparticle-coated nanowires grew under the simultaneous action of Si vapor deposition and bombardment by Si nanoparticles. Total process time, including both steps, equaled 5 min, and resulted in formation of a dense network of randomly oriented nanowires covering1.5 cm² of substrate area. The nanowires are composed of single-crystal Si. The diameters of the nanowires vary over the range 100–800 nm. Each nanowire has a crystalline TiSi₂ catalyst particle, believed to have been solid during nanowire growth, at its tip.     

Cytotoxicity and ion release of alloy nanoparticles

It is well-known that nanoparticles could cause toxic effects in cells. Alloy nanoparticles with yet unknown health risk may be released from cardiovascular implants made of Nickel–Titanium or Cobalt–Chromium due to abrasion or production failure. We show the bio-response of human primary endothelial and smooth muscle cells exposed to different concentrations of metal and alloy nanoparticles. Nanoparticles having primary particle sizes in the range of 5–250 nm were generated using laser ablation in three different solutions avoiding artificial chemical additives, and giving access to formulations containing nanoparticles only stabilized by biological ligands. Endothelial cells are found to be more sensitive to nanoparticle exposure than smooth muscle cells. Cobalt and Nickel nanoparticles caused the highest cytotoxicity. In contrast, Titanium, Nickel–Iron, and Nickel–Titanium nanoparticles had almost no influence on cells below a nanoparticle concentration of 10 μM. Nanoparticles in cysteine dissolved almost completely, whereas less ions are released when nanoparticles were stabilized in water or citrate solution. Nanoparticles stabilized by cysteine caused less inhibitory effects on cells suggesting cysteine to form metal complexes with bioactive ions in media.     

Synthesis of NiAu alloy and core–shell nanoparticles in water-in-oil microemulsions

NiAu alloy nanoparticles with various Ni/Au molar ratios were synthesized by the hydrazine reduction of nickel chloride and hydrogen tetrachloroaurate in the microemulsion system. They had a face-centered cubic structure and a mean diameter of 6–13 nm, decreasing with increasing Au content. As Au nanoparticles did, they showed a characteristic absorption peak at about 520 nm but the intensity decreased with increasing Ni content. Also, they were nearly superparamagnetic, although the magnetization decreased significantly with increasing Au content. Under an external magnetic field, they could be self-organized into the parallel lines. In addition, the core–shell nanoparticles, Ni₃Au₁@Au, were prepared by the Au coating on the surface of Ni₃Au₁ alloy nanoparticles. By increasing the hydrogen tetrachloroaurate concentration for Au coating, the thickness of Au shells could be raised and led to an enhanced and red-shifted surface plasmon absorption.     

Core–shell nanostructures and nanocomposites of Ag@TiO2: effect of capping agent and shell thickness on the optical properties

Two different shell-forming reagents viz. titanium isopropoxide and titanium hydroxyacylate, have been employed to obtain core–shell nanostructures of Ag@TiO₂. However, nanocomposites were formed when the shell-forming agent, titanium isopropoxide, was added before breaking the micelles. Titanium hydroxyacylate has been used for the first time as a shell-forming agent which resulted in uniform core–shell structures of Ag@TiO₂ with core diameter ranging from 10 to 40 nm and a shell thickness of 10–50 nm. The low rate of hydrolysis of titanium hydroxyacylate than titanium isopropoxide (used in other methods) appears to be responsible for the uniform shell thickness. The presence of capping agent (2-mercaptoethanol) disrupts the formation of a uniform shell structure of Ag@TiO₂. HRTEM, IR, and XPS studies of Ag@TiO₂ synthesized using capping agent show the formation of Ag₂S coated with an amorphous layer of TiO₂. A red shift of 25 and 10 nm was observed in the surface plasmon band of silver for Ag@TiO₂ core–shell structures (compared with that of silver nanoparticles) synthesized using titanium hydroxyacylate and titanium isopropoxide, respectively. The presence of capping agent (2-mercaptoethanol) masks the surface plasmon peak. Photoluminescence studies show an increase in the emission intensity for the core–shell structures when compared to that of TiO₂ nanoparticles.     

Electronic excitations and optical response of metal nanocomposites under heavy ion implantation

The optical transmission and ion-induced luminescence under implantation of copper ions into quartz glass (a-SiO₂) have been measured to study the processes of formation of copper nanoparticles. It is shown that in situ measurements are more informative in comparison with the ordinary approach—investigation of the properties of ion-implanted nanocomposites only after implantation. A series of experiments was performed to prove that the ion-induced luminescence band at 545–550 nm is due to Cu⁺ ions dissolved in a-SiO₂. The combined use of in situ optical techniques makes it possible to monitor the states of implanted copper (metal nanoparticles and dissolved atoms) by the change in the optical absorption near the surface plasmon resonance of nanoparticles and by the intensity of ion-induced luminescence of Cu⁺ states in solid solution. It is shown that the optical bands of defects, dissolved copper, and nanoparticles can be separated within a simple linear approximation. Near the surface plasmon resonance and defect bands, ion-induced transient optical absorption has been revealed. The transient optical absorption near the surface plasmon resonance is explained by the temperature effect. The relationship between the electronic excitation, radiation-induced optical response, and the kinetics of nanoparticle formation is analyzed. Several stages of nanoparticle formation have been established: accumulation of implanted copper in solid solution, nucleation of nanoparticles, coalescence, growth of nanoparticles, and saturation of nanocomposites.