Crosslinking induced by in‐situ coordination in acrylonitrile butadiene rubber/poly(vinyl chloride) alloy,filled with anhydrous copper sulfate particles

Acrylonitrile butadiene rubber (NBR)/poly(vinyl chloride) (PVC) alloy, filled with anhydrous copper sulfate (CuSO₄) particles, was investigated for the first time. The material could be crosslinked in the existence of CuSO₄ by heat pressing, without any other crosslink agents. The crosslinking in the material was induced by in situ coordination between nitrile groups of NBR and solid CuSO₄ particles, which is thoroughly different from the traditional vulcanization of rubber materials. The coordination crosslinking is formed during heat pressing, other than in solutions, which is valuable for practical applications. The resulting material showed excellent tensile properties, and the maximum strength was close to 90 MPa. The CuSO₄ particles act not only as crosslink agents, but also as reinforcing fillers in the polymer matrix. In this work, dynamic mechanical analysis, differential scanning calorimetry, Fourier transform infrared spectrum, X‐ray photoelectron spectroscopy, scanning electron microscope, energy‐dispersive X‐ray spectrum, equilibrium swelling method, and tensile test were performed for the characterization of the material. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 378–386, 2006     

Novel in situ coordination copper sulfate/ acrylonitrile–butadiene rubber composite

A novel rubber composite of acrylonitrile–butadiene rubber (NBR) filled with anhydrous copper sulfate (CuSO₄) particles was investigated. Dynamic mechanical analysis, differential scanning calorimetry, X‐ray photoelectron spectroscopy, tensile testing, and an equilibrium swelling method were used for the characterization of this novel CuSO₄/NBR composite. The results indicated that the composite had wonderful mechanical properties, which profited from the in situ coordination crosslinking interactions between the nitrile groups (? CN) of NBR and solid CuSO₄ particles. Scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, and transmission electron microscopy results showed that CuSO₄ particles played two roles, acting as both crosslink agents and reinforcing fillers in the matrix. The double actions of CuSO₄ gave the CuSO₄/NBR composites their excellent mechanical properties. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 571–576, 2007     

Crosslinking behavior and enhanced mechanical properties of acrylonitrile‐butadiene rubber composites by incorporating aluminum ammonium sulfate particles

The crosslinked structure formed by the metal coordination bonding provides excellent and new properties for rubber materials. Herein, the crosslinking of acrylonitrile‐butadiene rubber (NBR) is induced by introducing aluminum ammonium sulfate (NH₄Al(SO₄)₂·12H₂O) particles. The crosslinking behavior, morphology, mechanical properties, and the Akron abrasion resistance of NBR/NH₄Al(SO₄)₂·12H₂O composites were fully explored. The results show that the three‐dimensional crosslinking structure is held together by metal–ligand coordination bonds between the nitrile group and AI(III). The coordination crosslink density exhibits a considerable increase with the addition of NH₄Al(SO₄)₂·12H₂O. Thus, the mechanical properties and abrasion resistance of the obtained composites are better than that of NBR/sulfur system. Interestingly, the elongation at break for NBR/NH₄Al(SO₄)₂·12H₂O composites is over 2000% due to the nature of coordination bonds. The abrasion volume loss decreases to 0.4 cm³ for NBR/NH₄Al(SO₄)₂·12H₂O composites with 20 phr NH₄Al(SO₄)₂·12H₂O particles as compared to 0.75 cm³ for NBR/sulfur system. The obtained NBR composites with facile preparation and excellent mechanical properties make the composites based on metal coordination bonding attractive for practical use. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 879–886     

(NBR/PVC)/CuSO_4复合材料中配位交联反应的研究

采用差示扫描量热法(DSC)和傅立叶转换红外光谱(FT-IR)对丁腈橡胶/聚氯乙烯合金/无水硫酸铜((NBR/PVC)/CuSO4)混合物的配位交联反应进行了研究.结果表明,(NBR/PVC)/CuSO4共混物在升温过程中出现两个放热峰,分别归因于腈基(—CN)和CuSO4之间的配位交联反应和体系中NBR/PVC的自交联反应.通过对共混物配位交联反应动力学参数的计算发现,混合物中CuSO4含量的多少并未对体系配位交联反应的进行产生影响.同时共混物中PVC的存在促进了配位交联反应的进行,降低了铜离子(Cu2+)与—CN之间配位交联反应的表观活化能Ea.     

Cure behavior of diglycidylether of bisphenol A/trimethylolpropane triglycidylether epoxy blends initiated by thermal latent catalyst

Cure behaviors of diglycidylether of bisphenol A (DGEBA)/trimethylolpropane triglycidylether (TMP) epoxy blends initiated by 1 wt % N‐benzylpyrazinium hexafluoroantimonate (BPH) as a cationic latent catalyst were investigated using DSC and rheometer. This system showed more than one type of reaction and BPH could be excellent thermal latent catalyst without any co‐initiator. The cure activation energy (E_a) obtained from Kissinger method using dynamic DSC data was higher in DGEBA/TMP mixtures than in pure DGEBA. Rheological properties of the blend system were investigated under isothermal condition using a rheometer. The gel time was obtained from the analysis of storage modulus (G′), loss modulus (G″) and damping factor (tanδ). The crosslinking activation energy (E_c) was also determined from the Arrhenius equation based on the gel time and curing temperature. As a result, the crosslinking activation energy showed a similar behavior with that obtained from Kissinger method. And the gel time decreased with increasing TMP content, which could be resulted from increasing the activated sites by trifunctional epoxide groups and decreasing the viscosity of DGEBA/TMP epoxy blend in the presence of TMP. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 2114–2123, 2000     

Thermorheological analysis of PVC blends

The effect of temperature on dynamic viscoelastic measurements of miscible poly (vinyl chloride) (PVC)/ethylene‐vinyl acetate–carbon monoxide terpolymer (EVA‐CO) and immiscible PVC/high‐density polyethylene (HDPE) and PVC/chlorinated polyethylene (CPE) molten blends is discussed. PVC plasticized with di(2 ethyl hexyl) phthalate (PVC/DOP) and CaCO₃ filled HDPE (HDPE/CaCO₃) are also considered for comparison purposes. Thermorheological complexity is analyzed using two time–temperature superposition methods: double logarithmic plots of storage modulus, G′, vs. loss modulus, G″, and loss tangent, tan δ, vs. complex modulus, G*, plots. Both methods reveal that miscible PVC/EVA‐CO and PVC/DOP systems are thermorheologically complex, which is explained by the capacity of PVC to form microdomains or crystallites during mixing and following cooling of the blends. For immiscible PVC/HDPE and PVC/CPE blends the results of log G′ vs. log G″ show temperature independence. However, when tan δ vs. log G* plots are used, the immiscible blends are shown to be thermorheologically complex, indicating that the morphology observed by microscopy and constitued by a PVC phase dispersed in a HDPE or CPE matrix, is reflected by this rheological technique. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 469–477, 2000     

COORDINATION CROSSLINKING OF NITRILE RUBBER FILLED WITH COPPER SULFATE PARTICLES

By incorporating copper sulfate(CuSO_4)particles into acrylonitrile butadiene rubber(NBR)followed by heat pressing,a novel vulcanization method is developed in rubber through the formation of coordination crosslinking.This method totally differs from traditional covalent or non-covalent vulcanization approaches of rubber.No other vulcanizing agent or additional additive is involved in this process.By analyzing the results of DMA,XPS and FT-IR,it is found that the crosslinking of CuSO_4 particles filled NBR was induced by in situ coordination between nitrogen atoms of nitrile groups (-CN)and copper ions(Cu~(2 ))from CuSO_4.SEM and EDX results revealed the generation of a core(CuSO_4 solid particle)- shell(adherent NBR)structure,which leads to a result that the crosslinked rubber has excellent mechanical properties. Moreover,poly(vinyl chloride)(PVC)and liquid acrylonitrile-butadiene rubber(LNBR)were used as mobilizer to improve the coordination crosslinking of CuSO_4/NBR.The addition of PVC or LNBR could lead to higher crosslink density and better mechanical properties of coordination vulcanization.In addition,crystal water in CuSO_4 played a positive role to coordination crosslinking of rubber because it decreased the metal point of CuSO_4 and promoted the metal ionization.     

Dynamic mechanical behavior of acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) blends

The dynamic mechanical behavior of uncrosslinked (thermoplastic) and crosslinked (thermosetting) acrylonitrile butadiene rubber/poly(ethylene‐co‐vinyl acetate) (NBR/EVA) blends was studied with reference to the effect of blend ratio, crosslinking systems, frequency, and temperature. Different crosslinked systems were prepared using peroxide (DCP), sulfur, and mixed crosslink systems. The glass‐transition behavior of the blends was affected by the blend ratio, the nature of crosslinking, and frequency. sThe damping properties of the blends increased with NBR content. The variations in tan δ_max were in accordance with morphology changes in the blends. From tan δ values of peroxide‐cured NBR, EVA, and blends the crosslinking effect of DCP was more predominant in NBR. The morphology of the uncrosslinked blends was examined using scanning electron and optical microscopes. Cocontinuous morphology was observed between 40 and 60 wt % of NBR. The particle size distribution curve of the blends was also drawn. The Arrhenius relationship was used to calculate the activation energy for the glass transition of the blends, and it decreased with an increase in the NBR content. Various theoretical models were used to predict the modulus of the blends. From wide‐angle X‐ray scattering studies, the degree of crystallinity of the blends decreased with an increasing NBR content. The thermal behavior of the uncrosslinked and crosslinked systems of NBR/EVA blends was analyzed using a differential scanning calorimeter. © 2002 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 40: 1556–1570, 2002     

Dynamic mechanical and solid-state NMR determination of molecular-scale heterogeneity in a raw elastomer,a microcrystalline polymer,and their blend

Dynamic mechanical and solid-state ¹³C nuclear magnetic resonance (NMR) analyses have been used to assess a molecular-scale heterogeneity in a raw elastomer (butadiene-acrylonitrile copolymer elastomer, NBR), a microcrystalline polymer (poly(vinyl chloride), PVC), and their 50/50 blend. The presence of the microcrystalline heterogeneity in PVC and in the blend was characterized by the temperature dependence of the frequency-swept dynamic mechanical behavior. The NMR T_1ρ relaxation experiments with cross-polarization (CP) and magic-angle spinning (MAS) revealed that (1) NBR contained a substantial fraction (ca. 27%) of a molecular-scale heterogeneity identified as butadiene blocks, (2) the fraction of microcrystallites in PVC was ca. 14%, (3) pure phases of both component polymers were present in the blend, dispersed in the mixed matrix, (4) the upper limit of the heterogeneous domains was estimated to be ca. 2.4 nm, and (5) fractions of heterogeneity tend to increase upon blending, indicating that the solubility of the butadiene block and syndiotactic PVC block decreases in the blend. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys, 35: 709–716, 1997     

Modification of poly(vinyl chloride). XXIX. Cross linking of poly(vinyl chloride) with 2-dibutylamino-4,6-dithiol-s-triazine and MGO

Thermal crosslinking of poly(vinyl chloride) (PVC) with 2-dibutylamino-4,6-dithiol-s-triazine (DB) and MgO has been studied to determine the kinetic parameters such as induction period (t₀), rate constant (k), and activation energy (E), and to elucidate the structure of crosslink and the crosslinking mechanism. The thermal crosslinking was treated as a pseudo-first-order reaction. In the crosslinking, k and t₀ were about 0.075 min^?1 and 6.8 min at 180°C, respectively, and E was 16.6 and 14.2 kcal/mole for k and 1/t₀, respectively. The structure of crosslink was confirmed to be indicated as the following scheme (I) from the results of model reactions and IR spectra of crosslinked products The crosslinking reaction was found to proceed through the following three processes: (1) formation of DB-Mg from DB and MgO; (2) formation of DB-Mg pendants by the reaction of PVC with DB-Mg; and (3) formation of crosslink by the reaction of PVC with DB-Mg pendants.     

硫酸铜含量对硫酸铜与丁腈橡胶之间配位交联反应的影响

利用丁腈橡胶(NBR)的可配位侧基——腈基(—CN)与金属盐硫酸铜(CuSO4)的铜离子(Cu2+)之间的配位反应制备了一种配位交联CuSO4/NBR.影响该配位交联反应的因素众多,如热压温度、热压时间、增塑剂等等,考察了CuSO4含量对其的影响.通过X射线光电子能谱(XPS)、动态力学分析(DMA)、差示扫描量热分析(DSC)等手段对CuSO4与NBR之间的配位交联反应进行了分析,并对所得配位交联的CuSO4/NBR进行了交联密度及力学性能的测试.结果发现,随CuSO4含量的不断增加,CuSO4与NBR的配位交联程度逐渐增强,且所得配位交联CuSO4/NBR显示出从典型橡胶到韧性塑料再到脆性塑料的力学转变特性.另外,通过扫描电子显微镜(SEM)及X射线能谱仪(EDX)对材料的微观结构进行了分析,发现CuSO4在聚合物基体中不仅充当交联剂的角色,而且还起着增强填料的作用.     

Increasing Reduction Potentials of Type 1 Copper Center and Catalytic Efficiency of Small Laccase from Streptomyces coelicolor through Secondary Coordination Sphere Mutations

The key to type 1 copper (T1Cu) function lies in the fine tuning of the Cu^II/I reduction potential (E°′_T1Cu) to match those of its redox partners, enabling efficient electron transfer in a wide range of biological systems. While the secondary coordination sphere (SCS) effects have been used to tune E°′_T1Cu in azurin over a wide range, these principles are yet to be generalized to other T1Cu-containing proteins to tune catalytic properties. To this end, we have examined the effects of Y229F, V290N and S292F mutations around the T1Cu of small laccase (SLAC) from Streptomyces coelicolor to match the high E°′_T1Cu of fungal laccases. Using ultraviolet-visible absorption and electron paramagnetic resonance spectroscopies, together with X-ray crystallography and redox titrations, we have probed the influence of SCS mutations on the T1Cu and corresponding E°′_T1Cu. While minimal and small E°′_T1Cu increases are observed in Y229F- and S292F-SLAC, the V290N mutant exhibits a major E°′_T1Cu increase. Moreover, the influence of these mutations on E°′_T1Cu is additive, culminating in a triple mutant Y229F/V290N/S292F-SLAC with the highest E°′_T1Cu of 556 mV vs. SHE reported to date. Further activity assays indicate that all mutants retain oxygen reduction reaction activity, and display improved catalytic efficiencies (k_cat/K_M) relative to WT-SLAC.     

Dynamic and Isothermal Thermogravimetric Degradation of Poly(vinyl Chloride)/Chlorinated Poly(ethylene) Blends

The thermal degradation of poly(vinyl chloride)/chlorinated poly(ethylene) (PVC/CPE) blends of different compositions was investigated by means of dynamic and isothermal thermogravimetric analysis in flowing atmosphere of nitrogen. Kinetic parameters (the apparent activation energy E, and pre-exponential factor Z) were calculated after Flynn-Wall-Ozawa method for the first stage of dynamic degradation of PVC/CPE blends, and after Flynn method for the isothermal degradation. In both cases, there is the compensation dependence between the values E and logZ. The values of compensation ratios as well as the characteristics of TG and DTG curves, confirm the stabilizing effect of CPE on PVC dehydrochlorination. This revised version was published online in July 2006 with corrections to the Cover Date.     

Influence of hyperbranched against linear architecture on crystallization behavior of poly(ε‐caprolactone)s in binary blends with poly(vinyl chloride)

Nonisothermal and isothermal crystallization behaviors of the hyperbranched poly(ε‐caprolactone) (HPCL)/poly(vinyl chloride) (PVC) and linear poly(ε‐caprolactone) (LPCL)/(PVC) blends were characterized with various blend composition such as 100/0, 95/5, 90/10, and 80/20, respectively. HPCL was synthesized through polycondensation of AB₂ macromonomer while LPCL and PVC were commercially purchased. The architectural characterization performed on ¹H NMR spectra revealed that HPCL consisted of about 3 AB₂ units and the linear segments consisted of 25 ε‐CL units. Through the nonisothermal crystallization analyses by modified Avrami approach with DSC crystallization exotherms, it was found that the crystallization rate was retarded by the increase in the noncrystallizable component (PVC) in the blends. This is in good agreement with the results of the isothermal crystallization analyses where time resolved small angle light scattering (SALS) and polarized optical microscopy (POM) were used. The effect of molecular architectural difference between HPCL and LPCL on the crystallization of their binary blends with PVC was elucidated by comparing the crystallization kinetic parameters. Both the nonisothermal and isothermal crystallization analyses showed that the crystallization rates of HPCL/PVC blends was faster than LPCL/PVC blends at given blend compositions. The faster crystallization of the HPCL/PVC blends is ascribed to the two specific architectural characteristics of HPCL; the branched structure and the incorporated long linear segments. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 577–589, 2007     

Synthesis,crystal structure,spectroscopy, and electrochemistry of a uranium complex

A uranium coordination compound with pyridine-2,6-dicarboxylic acid in deionized water has been synthesized and characterized by IR, UV, XPS, and X-ray single-crystal diffraction. The crystal belongs to the monoclinic system, space group C2/c with a?=?1.8427(4)?nm, b?=?0.6886(16)?nm, c?=?1.5442(4)?nm, α?=?90°, β?=?94.082(2)°, γ?=?90°, Z?=?4, and V?=?1.9544(8)?nm³. The structure shows an eight-coordinate uranium forming a hexagonal bi-pyramidal 3-D geometry with pyridine-2,6-dicarboxylate as building units. Fluorescent studies show several strong emissions. Cyclic voltammetric measurement of the compound reveals that uranium(VI) is reduced irreversibly at E _1/2?=?927?mV with ΔE _p?=?77?mV, E _1/2?=??289?mV with ΔE _p?=?113?mV. The electron transfer number (n) involved in reduction processes could be calculated to be approximately two and one, which corresponded to the unusual U(VI)/U(IV) and U(IV)/U(III) couples.     

On-Line Coupling of High-Performance Liquid Chromatography to Atmospheric Pressure Chemical Ionization Mass Spectrometry (HPLC/APCI-MS and MS/MS). The Pollen Analysis of Hippeastrum x hortorum (Amaryllidaceae)

A H₂O/MeOH extract of the pollen of Hippeastrum x hortorum (Amaryllidaceae) was analyzed. A mixture of different compounds (at the most 84) was found, namely the geometrically ((E,E), (E,Z), (Z,E), and (Z,Z) and structurally isomeric N,N′-dicoumaroyl (=N,N′-bis[3-(4-hydroxyphenyl)prop-2-enoyl]), N,N′-diferuloyl (=N,N′-bis[3-(4-hydroxy-3-methoxyphenyl)prop-2-enoyl]), N,N′-disinapoyl (=N,N′-bis[3-(4-hydroxy-3,5-dimethoxyphenyl)prop-2-enoyl]), N-coumaroyl-N′-feruloyl, and N-feruloyl-N′-sinapoyl derivatives of spermidine (=4-azaoctane-1,8-diamine=N-(3-aminopropyl)butane-1,4-diamine). Their structures were proven by using on-line-coupled high-performance liquid chromatography and atmospheric-pressure chemical-ionization mass spectrometry (HPLC-UV(DAD)/APCI-MS and MS/MS), UV-induced (E)⇌(Z) photoisomerization, and catalytic hydrogenation, as well by comparing their spectra and chromatographic behavior with those of synthetic standards. According to the physicochemical properties of these natural compounds, a proposed biological function is discussed.     

The relationship between the structures of Cu(II) complexes and their chemical transformations

The paper reports an attempt to correlate the structures of hydrates of copper(II) sulphate with some characteristic features of the kinetics of their thermal decompositions. Non-isothermal thermogravimetric measurements were employed to obtain values of experimental activation energy and entropy for the dehydration of CuSO₄ · 5 H₂O, CuSO₄ · 3 H₂O and CuSO₄ · H₂O. The values ofE ^* andΔS ^* for the dehydration of CuSO₄ · 3 H₂O were found to be only little affected by the mode of preparation of this compound. On the other hand, the values ofE ^* andΔS ^* for the dehydration of CuSO₄ · ·H₂O are strongly dependent on whether this compound was prepared by thermal decomposition of CuSO₄ · 5 H₂O or CuSO₄ · 3 H₂O, or by crystallization from solution. As regards the crystalline hydrates of copper(II) sulphate, the greatest energetic hindrance for dehydration was observed for CuSO₄ · 3 H₂O. The experimental results are also discussed with respect to the present opinions concerning the possibilities of using thermal analyses to obtain information on the relationship between the structures and reactivities of solids.     

Double‐crosslinked reversible redox‐responsive hydrogels based on disulfide–thiol interchange

We present novel redox‐responsive hydrogels based on poly(N‐isopropylacrylamide) or poly(acrylamide), consisting of a reversible disulfide crosslinking agent N,N′‐bis(acryloyl)cystamine and a permanent crosslinking agent N,N′‐methylenebisacrylamide for microfluidic applications. The mechanism of swelling/deswelling behavior starts with the cleavage and reformation of disulfide bonds, leading to a change of crosslinking density and crosslinking points. Raman and ultraviolet‐visible spectroscopy confirm that conversion efficiency of thiol–disulfide interchange up to 99%. Rheological analysis reveals that the E modulus of hydrogel is dependent on the crosslinking density and can be repeatedly manipulated between high‐ and low‐stiffness states over at least 5 cycles without significant decrease. Kinetic studies showed that the mechanical strength of the gels changes as the redox reaction proceeds. This process is much faster than the autonomous diffusion in the hydrogel. Moreover, cooperative diffusion coefficient (D_coop) indicates that the swelling process of the hydrogel is affected by the reduction reaction. Finally, this reversibly switchable redox behavior of bulky hydrogel could be proven in microstructured hydrogel dots through short‐term photopatterning process. These hydrogel dots on glass substrates also showed the desired short response time on cyclic swelling and shrinking processes known from downsized hydrogel shapes. Such stimuli‐responsive hydrogels with redox‐sensitive crosslinkers open a new pathway in exchanging analytes for sensing and separating in microfluidics applications. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019 , 57, 2590–2601     

结晶水对硫酸铜与丁腈橡胶之间配位交联反应的影响

利用动态力学分析(DMA)、差示扫描量热分析(DSC)、扫描电子显微镜(SEM)、平衡溶胀法、力学性能测试等分析手段, 通过研究五水硫酸铜(CuSO4·5H2O)填充的NBR考察了结晶水对CuSO4与NBR之间配位交联反应的影响. 结果表明, 结晶水的存在可以促进该配位交联反应.     

Studies on curing kinetics of a novel combined liquid crystalline epoxy containing tetramethylbiphenyl and aromatic ester‐type mesogenic group with diaminodiphenylsulfone

The curing kinetics of a novel liquid crystalline epoxy resin with combining biphenyl and aromatic ester‐type mesogenic unit, diglycidyl ether of 4,4′‐bis(4‐hydroxybenzoyloxy)‐3,3′,5,5′‐tetramethyl biphenyl (DGE‐BHBTMBP), and the curing agent diaminodiphenylsulfone (DDS) was studied using the advanced isoconvensional method (AICM). DGE‐BHBTMBP/DDS curing system was investigated the curing behavior by means of differential scanning calorimetry (DSC) during isothermal and nonisothermal processes. Only one exothermal peak appeared in isothermal DSC curves. A variation of the effective activation energy with the extent of conversion was obtained by AICM. Three different curing stages were confirmed. In the initial curing stage, the value of E_a is dramatically decreased from ～90 to ～20 kJ/mol in the conversion region 0–0.2 for the formation of LC phase. In the middle stage, the value of E_a keeps about ～80 kJ/mol for cooperative effect of reaction mechanism and diffusion control. In the final stage, a significant increase of E_a from 84 to 136 kJ/mol could be caused by the mobility of longer polymer chains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3922–3928, 2007