Dynamic mechanical properties of polystyrene ionomers containing both carboxylate and sulfonate anionic groups

Polystyrene‐based ionomers possessing sodium methacrylate (MA) and sodium styrenesulfonate (SS) units in each polymer chain [poly(styrene‐co‐methacrylate‐co‐styrenesulfonate) (PSMA‐SS)] were synthesized. The dynamic mechanical properties of PSMA‐SS ionomers were studied and compared with those of styrene ionomers containing only MA (PSMA ionomer) or SS (PSS ionomer) units. It was observed that the ionic moduli of PSMA‐SS ionomers depended directly on the total ion content and that the ionic modulus was highest for the PSMA ionomer and lowest for the PSMA‐SS ionomer. The matrix T_gs of the three ionomer systems were found to be similar to each other; the cluster T_g of PSMA‐SS ionomer was higher than that of PSS ionomer at low SS contents but became closer to each other at high SS contents. In addition, the small‐angle X‐ray scattering study revealed that the multiplet size might be in the following order: PSMA‐SS > PSS > PSMA. This implied that at the same ion content, the fractions of cluster regions were smallest for PSMA‐SS ionomer in comparison with those of PSS or PSMA ionomers. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys, 2012     

Effects of Na‐sulfopropyl groups on the mechanical properties and morphology of polystyrene‐co‐methacrylate ionomers

The dynamic mechanical properties and morphology of poly(styrene‐co?3‐sulfopropyl sodium‐methacrylate) SSPMANa ionomers were investigated. It was found the increasing rate of ionic moduli of the SSPMANa ionomer was very low, and the cluster T_g of the ionomers remained more or less constant with increasing ion content. A well‐developed SAXS peak was seen for low ion content SSPMANa ionomers and the peak position changed slightly with ion content. Thus, it was suggested that the presence of the alkyl ester side chains made the ion pairs form multiplets more easily at their prevalent distances, and the small‐agglomerated multiplets were dispersed in the polymer matrix relatively evenly. The interpretation of ionic moduli using a number of theories implied that the multiplets and clusters acted as effective crosslinks and filler particles, respectively, and the size and shape of the clusters were irregular. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1043–1053     

Layer‐by‐layer ionomer films made from poly(styrene‐co‐styrenesulfonic acid) and poly(methyl methacrylate‐co‐4‐vinylpyridine) in tetrahydrofuran

Thin films were fabricated layer‐by‐layer (LbL) via ionic bonds formed between a cationic ionomer and an anionic ionomer, which were produced via proton transfer from poly(styrene‐co‐styrenesulfonic acid) to poly(methyl methacrylate‐co‐4‐vinylpyridine) in an organic solvent, tetrahydrofuran. Ionic contents of the ionomers were very low down to 5.6 mol %, much lower than usual polyelectrolytes. The build up of the LbL films was demonstrated by UV/vis spectroscopy: the absorbance of the phenyl rings in styrene residues increased with the number of depositions (thus the number of layers). Transmission electron microscopy observation of strained thin films showed unique deformation mode, involving many bands that developed both in the parallel and perpendicular directions to the stress axis. This is quite different from the deformation modes seen for ionomer blend films and for coextruded polystyrene/poly(methyl methacrylate) multilayer tapes. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 50: 101–105, 2012     

Plasticization of a poly(ethyl acrylate) ionomer by an alkyl aniline

The plasticization by 4-decylaniline (4DA) of a microphase-separated poly(ethyl acrylate) ionomer containing sodium carboxylate groups is examined. Dynamic mechanical thermal analysis, supplemented by differential scanning calorimetry, shows that the matrix and cluster glass transitions (T_g's) in the ionomer are both depressed by ca. 1°C/wt % 4DA; this, in turn, is similar to the T_g depression in the blend of the parent poly(ethyl acrylate) (PEA) with 4DA. There is no evidence of 4DA crystallinity in the blend. Small-angle x-ray scattering (SAXS) measurements show that the ionomer peak increases in intensity and decreases in scattering angle with increasing concentration of 4DA in the blend; the corresponding Bragg spacing, initially at 2.3 nm, increases by ca. 0.04 nm/wt % 4DA. These results, supported by preliminary spectroscopic measurements, are attributed to hydrogen bonding interactions between the amine groups of 4DA and the ester groups in PEA and the ionomer, rendering the blend miscible. It is argued that the uniform distribution of 4DA throughout the material plasticizes both phases of the ionomer by adding free volume; this also accounts for the increase in the characteristic spacing detected by SAXS.     

Dynamic melt properties of ionic blends of polystyrene and poly(ethyl acrylate)

Ionic interactions in blends of poly(styrene-co-styrene–sulfonic acid) and poly(ethyl acrylate-co-4-vinylpyridine) result in greatly extended rubbery regions. Measurements of dynamic shear moduli as a function of frequency at various temperatures above the glass transition indicate that time–temperature superposition is applicable in almost all cases. Relative to a blend of pure polystyrene with pure poly(ethyl acrylate), the copolymeric blends strongly resemble one another regardless of either compatibility or ion content. Higher ion content appears to enhance the extension of the rubbery plateau. True flow is not achieved even at temperatures as high as 220°C (0.1 rad/s). Flow is clearly evident in the nonionic blend at 170°C (0.1–1.0 rad/s). It is postulated that the ionic interactions are such that bond breaking and reforming are more rapid than the rate of chain slippage.     

Wettability of poly(styrene‐co‐acrylate) ionomers improved by oxygen‐plasma source ion implantation

The surfaces of poly(styrene‐co‐acrylic acid) copolymers and their Na‐ and Cs‐neutralized ionomers were modified by O₂‐plasma source ion implantation (PSII) treatment to improve the surface wettability. The changes in the surface wettability, composition, and structure upon the PSII treatment were examined with contact‐angle measurements and X‐ray photoelectron spectroscopy. The untreated surfaces of the acid copolymers and ionomers exhibited different surface energies; this implied clearly that the type of ion species affects the surface hydrophilicity. Also, the PSII treatment induced oxygen‐containing groups to reside on the surface and ionic groups to come out toward the surface; this made the surfaces of the ionomers more hydrophilic as compared with that of the acid copolymers. The ionomers also showed slow hydrophobic recovery. Thus, it was suggested that the reduced mobility of the polymer chain because of the presence of ionic aggregates results in restricted reorientation of oxygen‐containing groups. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1791–1797, 2003     

Effect of Na‐ionomer on dynamic rheological,dynamic mechanical and creep properties of acrylonitrile styrene acrylate (ASA)/Na+1 poly (ethylene‐co‐methacrylic acid) ionomer blend

A special class of engineered copolymers, called ionomers, comprising both electrically neutral repeating units and a fraction of ionized units was melt blended to weather resistant acrylonitrile/styrene/acrylate (ASA) terpolymer for improved electrical conductivity, heat sealing ability, direct adhesion to several polymers, glass and metals without affecting the aesthetics and colorability of ASA. The similar chemical nature of one of the components of each blended materials viz. acrylate rubber in ASA and acrylic acid of Na‐ionomer in addition to the presence of ionic crosslinking within Na‐ionomer, polar acrylonitrile group in ASA affects chain dynamics as compared to neat polymers. In this context, dynamic rheological properties, DMA properties, creep behavior and DSC of the newly developed ASA/Na‐ionomer blends were analyzed. Based on Na‐ionomer content, the blend system either forms “mushroom” or “brush” type conformation and formation of ionic crosslinking in “brush regime” leads to three tiers Caylay tree conformation. The different chain topology resulted into characteristic loss modulous (G″) curve during stress relaxation process. The chain conformation as well as ionic crosslinking and ion–dipole interaction between the blend components also affected DSC endotherm peak and glass transition temperature. The tan δ peak temperature from DMA also revealed the similar observation. The creep compliance of the blends was dependent on Na‐ionomer content and with temperature. The Findley model analysis of creep compliance suggested that the creep compliance was depended on Na‐ionomer content and ionic crosslinking controlled the creep. The findings can be utilized to design weather resistant smart polymer using suitable filler system. Copyright © 2014 John Wiley & Sons, Ltd.     

Synthesis of poly[(2‐oxo‐1,3‐dioxolane‐4‐yl) methyl methacrylate‐co‐ethyl acrylate] by incorporation of carbon dioxide into epoxide polymer and the miscibility behavior of its blends with poly(methyl methacrylate) or poly(vinyl chloride)

This study was related to the investigation of the chemical fixation of carbon dioxide to a copolymer bearing epoxide and the application of the cyclic carbonate group containing copolymer‐to‐polymer blends. In the synthesis of poly[(2‐oxo‐1,3‐dioxolane‐4‐yl) methyl methacrylate‐co‐ethyl acrylate] [poly(DOMA‐co‐EA)] from poly(glycidyl methacrylate‐co‐ethyl acrylate) [poly(GMA‐co‐EA)] and CO₂, quaternary ammonium salts showed good catalytic activity. The films of poly(DOMA‐co‐EA) with poly(methyl methacrylate) (PMMA) or poly(vinyl chloride) (PVC) blends were cast from N,N′‐dimethylformamide solution. The miscibility of the blends of poly(DOMA‐co‐EA) with PMMA or PVC have been investigated both by DSC and visual inspection of the blends. The optical clarity test and DSC analysis showed that poly(DOMA‐co‐EA) containing blends were miscible over the whole composition range. The miscibility behaviors were discussed in terms of Fourier transform infrared spectra and interaction parameters based on the binary interaction model. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 1472–1480, 2001     

Rheological and thermal study of delayed crystallization in poly(butylene terephthalate)/ethylene‐co‐ethyl acrylate blends

The effects of the composition and resulting morphology on the crystallization and rheology of blends containing poly(butylene terephthalate) (PBT) and an ethylene‐co‐ethyl acrylate (EEA) copolymer, two immiscible polymers, were studied over the entire range of volume fractions. Differential scanning calorimetry (DSC) thermograms recorded during cooling showed important differences, mainly in terms of the PBT crystallization temperatures, depending on the blend composition. In addition to the classical crystallization peaks of PBT and EEA, a third crystallization peak appeared for blends containing less than 60% PBT. This peak was attributed to a delayed crystallization of PBT. This phenomenon was examined in terms of homogeneous crystallization. Linear viscoelastic measurements allowed the delayed crystallization behavior in these polymer blends to be displayed. Indeed, the variation of the storage modulus with the temperature showed increasing steps during cooling. These sudden increases appeared at temperatures very close to those at which the crystallization peaks were observed in the DSC experiments. This behavior was verified for different blend compositions. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 714–721, 2004     

Tailor‐made poly(ethyl acrylate) by atom transfer radical polymerization

Atom transfer radical polymerization (ATRP) of ethyl acrylate (EA) was carried out using different initiators, CuBr or CuCl as catalyst in combination with different ligands e.g., 2,2′‐bipyridine (bpy) and N,N,N′,N″N″‐pentamethyl diethylenetriamine (PMDETA). Use of PMDETA as ligand resulted in faster polymerization rate (95% conversion in 15 min) than those using bipyridine (～58% conversion in 10.5 h). This is due to the lower reduction potential of copper‐amine than that of copper‐bpy complex, resulting in higher rates of activation of dormant halides. Use of ethylene carbonate as solvent lead to faster polymerization rate and better control in polymerization when compared with p‐xylene as solvent. The reaction temperature had a positive effect on polymerization rate and the optimum reaction temperature was found to be 90 °C. An apparent enthalpy of activation of ～85 kJ/mol was determined for the ATRP of ethyl acrylate, corresponding to an enthalpy of equilibrium of ～64 kJ/mol. By judicious choice of the reaction parameters it was possible to tailor the end group of the final polymer. MALDI‐TOF‐MS analysis and the chain extension experiment of poly(ethyl acrylate) (PEA) prepared using bpy as ligand showed the presence of ? Br as the end group. On the contrary, when PMDETA was used as the ligand, the mass spectra analysis showed hydrogen terminated polymer as the major species towards the end of polymerization. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 1661–1669, 2007     

Synthesis and properties of the ionomer diblock copolymer poly(4‐vinylbenzyl triethyl ammonium bromide)‐b‐polyisobutene

A new amphiphilic diblock copolymer containing an ionomer segment, poly[(4‐vinylbenzyl triethyl ammonium bromide)‐co‐(4‐methylstyrene)‐co‐(4‐bromomethylstyrene)]‐b‐polyisobutene [poly(4‐VBTEAB)‐b‐PIB], was synthesized by the chemical modification of poly(4‐methylstyrene)‐b‐polyisobutene [poly(4‐MSt)‐b‐PIB]. First, the 4‐methylstyrene moiety in poly(4‐MSt)‐b‐PIB was brominated with azobisisobutyronitrile as an initiator at 60 °C in CCl₄, and then the highly reactive benzyl bromide groups were ionized by a reaction with triethylamine in a toluene/isopropyl alcohol (80/20 v/v) mixture at about 85 °C to produce the ionomer diblock copolymer poly(4‐VBTEAB)‐b‐PIB. The solubility of the ionomer block copolymer was quite different from that of the corresponding poly[(4‐methylstyrene)‐co‐(4‐bromomethylstyrene)]‐b‐polyisobutene {poly[(4‐MSt)‐co‐(4‐BrMSt)]‐b‐PIB}. Transmission electron microscopy observations demonstrated that all three diblock copolymers had microphase‐separation structures in which polyisobutene (PIB) domains existed in the continuous phase of the poly(4‐methylstyrene) segment or its derivative segment matrix. Dynamic mechanical thermal analysis measurements showed that poly[(4‐MSt)‐co‐(4‐BrMSt)]‐b‐PIB had two glass‐transition temperatures (T_g's), ?56 °C for the PIB segment and 62 °C for the poly[(4‐MSt)‐co‐(4‐BrMSt)] domain, whereas poly(4‐VBTEAB)‐b‐PIB showed one T_g at ?8 °C of the PIB domain; T_g of the poly[(4‐vinylbenzyl triethyl ammonium bromide)‐co‐(4‐methylstyrene)‐co‐(4‐bromomethylstyrene)] domain was not observable because of the strong ionic interactions resulting in a higher T_g and a retention of modulus up to 124 °C. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2755–2764, 2003     

Synthesis by Emulsion Polymerization of Poly(butyl acrylate-co-silver acrylate) Ionomers and Evaluation of their Possible Applications

The synthesis by emulsion polymerization and the characterization by a battery of techniques of poly(butyl acrylate-co-silver acrylate) [poly(BuAc-co-AgAc)] ionomers are reported here. Reaction rates were fast and conversions around 90% were obtained in less than one hour, regardless of the initial ratio of butyl acrylate and silver acrylate employed (BuAc/AgAc = 90/10, 80/20, 70/30). Particle size was in the range of 176 to 200 nm, depending on the BuAc/AgAc ratio. Ionomers’ formation was corroborated by infrared spectroscopy and inferred by differential scanning calorimetry (DSC). DSC disclosed that the poly(BuAc-co-AgAc) has two glass transition temperatures: one at ca. ?49°C due to relaxation of the ionomer backbone domains rich in BuAc and another ca. 35°C due to the relaxation of the backbone domains where the AgAc-units content was higher. Young moduli increased as the copolymers became richer in AgAc. Antibacterial tests against Escherichia coli with the 90/10 (BuAc/AgAc) ionomer revealed that the bacteria population diminishes from 5 log CFU/mL to less than 0.3 MPN/mL after one hour of contact with the ionomers. Also, we demonstrated that the ionomers are excellent compatibilizers for making semiconductive films of n-dodecylbenzene sulfonic acid-doped polyaniline (PANIDBSA)-poly(BuAc-co-AgAc) and poly(n-butyl methacrylate) (PBMA) blends. The electrical conductivity of the blend films, which were homogeneous, rose as the AgAc content in the films increased.     

Microwave assisted hydroxyalkylamidation of poly(ethylene‐co‐acrylic acid) and formation of grafted poly(ϵ‐caprolactone) side chains

The microwave assisted amidation of poly(ethylene‐co‐acrylic acid) (PEAA) with 2‐(2‐aminoethoxy)ethanol was performed to yield a hydroxy functionalized poly(ethylene) based copolymer (PEAAOH) in a single step. PEAAOH was used as a polyinitiator for the ring‐opening polymerization of ε‐caprolactone. The obtained graft copolymers were studied via ¹H NMR spectroscopy, gel permeation chromatography, differential scanning calorimetry, polarized optical microscopy, and scanning electron microscopy. Microscopy methods show a crystallization behavior of banded spherulites. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3659–3667, 2007     

Photolysis of poly(ethyl acrylate) and poly(n–butyl acrylate) in vacuo

Thin films of poly(ethyl acrylate) and poly(n-butyl acrylate) were decomposed in vacuo by means of a high pressure Hg lamp, and the rate of development of volatile products was measured. The main gaseous products were CO, CO₂, and the alcohol, aldehyde, alkane, and formate derived from the respective ester groups. In addition poly(ethyl acrylate) evolved acetal as well as ethyl propionate, while n-butyl valerate was evolved from poly(n-butyl acrylate) only after prolonged exposure. All products and the principal features of the decomposition are discussed.     

Light-scattering study of the coil-to-globule transition of linear poly(N-isopropylacrylamide) ionomers in water

The coil-to-globule transition of two poly(N-isopropylacrylamide) (PNIPAM) ionomers with different ionic contents (0.8 and 4.5 mol %), but similar weight average molar masses, in deionized water was investigated by a combination of static and dynamic light scattering. In spite of the large difference in their ionic contents, both the ionomers have a nearly same lower critical solution temperature (LCST, ∼ 32.5°C). At temperatures higher than the LCST, the ionomer chains undergo a simultaneous intrachain coil-to-globule transition and interchain aggregation to form nanoparticles thermodynamically stable in water. The average size of the nanoparticles decreases respectively as the ionic content increases and the ionomer concentration decreases. The interchain aggregation can be completely suppressed in an extremely dilute ionomer solution (< ∼ 5 × 10⁻⁶ g/mL), so that the intrachain coil-to-globule transition leads to the collapse of the ionomer chains into individual single-chain nanoparticles. Our results clearly indicate that there is a hysteresis in the colling process (the globule-to-coil transition). © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 1501–1506, 1998     

Preparation and ion conductivities of the plasticized polymer electrolytes based on the poly(acrylonitrile‐ co‐lithium methacrylate)

The polymer electrolytes composed of poly(acrylonitrile‐co‐lithium methacrylate) [P(AN‐co‐LiMA)], ethylene carbonate (EC), and LiClO₄ salts have been prepared. The ion groups in the P(AN‐co‐LiMA) were found to prevent EC from crystallization through their ion–dipole interactions with the polar groups in the EC. This suppression of the EC crystallization could lead to the enhancement of the ion conductivity at subambient temperature. The polymer electrolytes based on the PAN ionomer with 4 mol % ion content exhibited ion conductivities of 2.4 × 10⁻⁴ S/cm at −10°C and 1.9 × 10⁻³ S/cm at 25°C by simply using EC as a plasticizer. In the polymer electrolytes based on the PAN ionomer, ion motions seemed to be coupled with the segmental motions of the polymer chain due to the presence of the ion–dipole interaction between the ion groups in the ionomer and the polar groups in the EC, while the ion transport in the PAN‐based polymer electrolytes was similar to that of the liquid electrolytes. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 247–252, 1999     

Synthesis of an alkali‐swellable emulsion and its effect on the rate of polymer diffusion in poly(vinyl acetate‐butyl acrylate) latex films

We describe the synthesis and characterization of a weakly cross‐linked poly(methacrylic acid‐co‐ethyl acrylate) alkali‐swellable emulsion (ASE), as well as an investigation of its influence on the rate of polymer diffusion in latex films. The films examined were formed from poly(vinyl acetate‐co‐butyl acrylate) latex particles containing a small amount of acrylic acid as a comonomer. Polymer diffusion rates were monitored by the energy transfer technique. We found that the presence of the ASE component, either in the acid form or fully neutralized by ammonia or sodium hydroxide, had very little effect on the polymer diffusion rate. However, in the presence of 2 wt % NH₄‐ASE, there was a small but significant increase in the polymer diffusion rate. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 5632–5642, 2005     

Stereoregularity of radically polymerized poly(alkyl acrylates) and poly(trimethylsilyl acrylates) and the preparation of syndiotactic poly(methyl acrylate)

Nuclear magnetic resonance (NMR) spectroscopy was used to determine the stereoregularity of radically polymerized poly(ethyl acrylates), poly(trimethylsilyl acrylates), and poly(isopropyl acrylate-α,β-d₂). The ethyl acrylate polymers consisted of a random configuration having about 50% of isotactic diads, and their stereoregularities were independent of the polymerization temperature (40 to ?78°C). Poly(trimethylsilyl acrylates) and poly(isopropyl acrylate-α,β-d₂) prepared at low temperatures had a syndiotactic configuration. Syndiotactic poly(methyl acrylate) was derived from syndiotactic poly(trimethylsilyl acrylate). For poly(methyl acrylate), an approximate estimation of the stereoregularity by infrared spectroscopy was proposed.     

Synthesis of superparamagnetic and thermoresponsive hybrid nanoparticles via surface‐mediated RAFT polymerization of di(ethylene glycol) ethyl ether acrylate and (oligoethylene glycol) methyl ether acrylate

A reversible addition‐fragmentation chain transfer (RAFT) agent was directly anchored onto superparamagnetic Fe₃O₄ nanoparticles (SPNPs) in a simple procedure using a ligand exchange reaction of 2‐[(dodecylsulfanylcarbonylthiolsulfanyl) propionic acid] (DCPA) with oleic acid initially present on the surface of Fe₃O₄ nanoparticles. The DCPA‐modified SPNPs were then used for the surface‐mediated RAFT polymerization of di(ethylene glycol) ethyl ether acrylate and (oligoethylene glycol) methyl ether acrylate to fabricate structurally well‐defined hybrid SPNPs with temperature‐responsive poly[di(ethylene glycol) ethyl ether acrylate‐co‐(oligoethylene glycol) methyl ether acrylate] shell and magnetic Fe₃O₄ core. Evidence of a well‐controlled surface‐mediated RAFT polymerization was gained from a linear increase of number‐average molecular weight with overall monomer conversions and relatively narrow polydispersity indices of the copolymers grown from the SPNPs. The resultant hybrid nanoparticles exhibited superparamagnetic property with a saturation magnetization of 55.1–19.4 emu/g and showed a temperature‐responsive phenomenon as the temperature changed between 25 and 40 ^°C. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 3420–3428     

Stable heterocumulene monomer in water; Synthesis and polymerization of (meth)acrylates having an isothiocyanate structure

Novel methacrylate and acrylate monomers having an isothiocyanate structure, 2‐isothiocyanatoethyl methacrylate (ITEMA) and 2‐isothiocyanatoethyl acrylate (ITEA), were synthesized, and their radical polymerizations were examined, respectively. ITEMA and ITEA were synthesized by addition of carbon disulfide to 2‐aminoethyl methacryrate or 2‐aminoethyl acrylate, followed by treatment with ethyl chloroformate. Radical polymerizations of the obtained monomers ( ITEMA , ITEA ) were carried out methyl ethyl ketone using 2,2'‐azobisisobutyronitrile (AIBN) as an initiator to obtain the corresponding polymers. The glass transition temperatures of the poly‐ITEMA and poly‐ITEA were determined to be 55 and 2 °C by differential scanning calorimetry, respectively. The 5 wt % decomposition temperatures of the poly‐ITEMA and poly‐ITEA were determined to be 277 and 269 °C by thermogravimetric analysis, respectively. Isothiocyanato groups in the monomers did not react with water in acetone solution at 60 °C for 24 h to be tolerable to water. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4522–4529