Spectroscopic study of the penetration depth of grafted polystyrene onto poly(tetrafluoroethylene‐co‐perfluoropropylvinylether) substrates. 1. Effect of grafting conditions

This study concerns the radiation grafting of styrene onto poly(tetrafluoroethylene‐co‐perfluoropropylvinylether) (PFA) substrates and the penetration depth of the graft. Grafting was obtained by the simultaneous irradiation method, and the spectroscopic analysis was made with the micro‐Raman technique. Effects of grafting conditions such as the type of solvent, dose rate, and irradiation dose on the grafting yield were investigated. Of the different solvents used, the most efficient in terms of increasing grafting yield were dichloromethane, benzene, and methanol, respectively. A mixture of methanol and dichloromethane used as a solvent for styrene achieved a higher degree of grafting and concentration of grafted polystyrene onto the surface of PFA substrates than solutions of the monomer in the separate solvents. The degree of grafting increased with increasing radiation dose up to 500 kGy, stabilizing above this dose. However, the grafting yield decreased with an increase in the dose rate. The increase in the overall grafting yield was accompanied by a proportional increase in the penetration depth of the grafts into the substrate. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3191–3199, 2002     

Pre‐Irradiation Grafting of Styrene/Divinylbenzene onto Poly(tetrafluoroethylene‐co‐hexafluoropropylene) from Non‐Solvents

Pre‐irradiation grafting of styrene/divinylbenzene (DVB) onto poly(tetrafluoroethylene‐co‐hexafluoropropylene) (FEP) films was studied with respect to the influence of solvent. Particularly favorable grafting conditions with long radical lifetimes and reasonably high polymerization rates were achieved with solvents that are precipitants for the newly formed polystyrene, e.g., low‐molecular‐mass alcohols like ⁱPrOH, AcOH, their mixtures with H₂O, and H₂O/surfactant systems. Using one of these solvents significantly extended the range of accessible graft levels, and a specific degree of grafting was obtained at a much lower monomer concentration and irradiation dose than with grafting in a good solvent such as toluene. As practical consequences, the monomer was used more efficiently, and the radiation damage of the perfluorinated base material was reduced with the result of improved mechanical properties of the grafted films.     

壳聚糖与N-异丙基丙烯酰胺接枝共聚凝胶的辐射合成及性能研究

采用γ辐射技术引发壳聚糖与N异丙基丙烯酰胺进行接枝共聚,制备了温度及pH敏感水凝胶.研究了单体浓度、辐射剂量等对接枝率和接枝效率的影响,并用13CCPMASNMR和TG表征了接枝物的结构.研究结果表明,用γ射线引发壳聚糖接枝异丙基丙烯酰胺具有较高的接枝率和接枝效率,接枝的聚合物具有明显的温度及pH敏感的特点.     

Grafting of hydroxymethylacrylamide and acrylic acid copolymer onto polyvinylidene fluoride membrane by supercritical carbon dioxide and its application in dye separation

We report a thermally induced graft copolymerization of acrylic acid and N‐hydroxymethylacrylamide onto polyvinylidene fluoride microporous membrane by using supercritical carbon dioxide as a solvent and carrier agent. The effects of monomer mole ratio, pressure, reaction temperature, time, and initiator concentration on the degree of grafting were investigated. The morphology of the grafted membrane was studied via scanning electron microscopy. Attenuated total reflectance infrared spectroscopy spectroscopy and X‐ray diffraction proved the existence of grafting monomers. The results of contact angle measurement and water filtration at different pH levels indicated pronounced pH‐sensitive behavior and increased hydrophilicity of the polyvinylidene fluoride grafted membrane. In particular, the grafted membrane was applied to the removal of methylene blue with a relative rejection of 98.1% compared with 30.5% of rejection observed from the pristine polyvinylidene fluoride membrane. Copyright © 2014 John Wiley & Sons, Ltd.     

Graft Copolymerization of 2‐Acrylamido‐2‐methyl Propane Sulfonic Acid on Dimethyl Sulfoxide Pretreated Poly(Ethylene Terephthalate) Films Using Cerium Ammonium Nitrate as Initiator

Abstract

In this study, graft polymerization of 2‐acrylamido‐2‐methyl propane sulfonic acid (AMPS) on poly(ethylene terephthalate) (PET) films using cerium ammonium nitrate (CeAN) as an initiator was investigated. Before the polymerization reaction was carried out, films were swelled in dimethyl sulfoxide (DMSO) at 140°C for 1 h. The effect of polymerization temperature, time, initiator, and monomer concentrations on the graft yield were investigated. It was observed that the graft yield was initially increased with increasing temperature, monomer, and initiator concentrations; and then decreased. Graft yield was found to increase with increasing polymerization time up to 5 h, then remain constant. The effects of monomer and initiator inclusions on the grafting yield were also examined. Optimum conditions for grafting were found to be [AMPS] = 1.0 M, [Ce⁴⁺] = 1.5 × 10^?2 M, T = 85°C and t = 5 h. The rate of grafting was found to be proportional to the 0.1 and 0.4 powers of monomer and initiator concentrations, respectively. The overall activation energy for the grafting was calculated to be 11.4 kcal mol^?1. The effect of grafting on PET film properties such as intrinsic viscosity and water absorption capacity were determined. The grafted PET films were characterized with FTIR spectroscopy and scanning electron microscopy (SEM).     

Kinetic study of preirradiation grafting of acrylic acid onto poly(tetrafluoroethylene–perfluorovinyl ether) copolymer

A kinetic study has been made on the preirradiation grafting of acrylic acid (AAc) onto poly(tetrafluoroethylene–perfluorovinyl ether) (PFA) film. The effect of grafting conditions was investigated. The dependences of the grafting rate on preirradiation dose and monomer concentration was found to be of the order of 0.5 and 1.3, respectively. The final degree of grafting was found to increase with dose and monomer concentration. However, it decreases as the grafting temperature increase. The overall activation energy for the graft polymerization was calculated from Arrhenius plots to be 5.6 kcal/mol. The activation energy for this grafting system was found to be independent of preirradiation dose used in the range from 10 to 100 kGy. The relationship between the grafting rate and film thickness gave a negative first-order dependence. The results suggest that the grafting proceeds by radical mechanism with bimolecular termination of growing chain radicals. It was reasonable concluded that this grafting proceeds from the surface to the center of film with progressive monomer diffusion through the grafted layer which swells in the monomer solution.     

Polymers from renewable resources. II. A study in the radio chemical grafting of poly(styrene‐alt‐maleic anhydride) onto cellulose extracted from pine needles

A binary mixture of styrene and maleic anhydride has been graft copolymerized onto cellulose extracted from Pinus roxburghii needles. The reaction was initiated with gamma rays in air by the simultaneous irradiation method. Graft copolymerization was studied under optimum conditions of total dose of radiation, amount of water, and molar concentration previously worked out for grafting styrene onto cellulose. Percentage of total conversion (Pg), grafting efficiency (%), percentage of grafting (Pg), and rates of polymerization (R_p), grafting (R_g), and homopolymerization (R_h) have been determined as a function of maleic anhydride concentration. The high degree of kinetic regularity and the linear dependence of the rate of polymerization on maleic anhydride concentration, along with the low and nearly constant rate of homopolymerization suggest that the monomers first form a complexomer which then polymerizes to form grafted chains with an alternating sequence. Grafting parameters and reaction rates achieve maximum values when the molar ratio of styrene to maleic anhydride is 1 : 1. Further evidence for the alternating monomer sequence is obtained from quantitatively evaluating the composition of the grafted chains from the FT‐IR spectra, in which the ratio of anhydride absorbance to aromatic (CC) absorbance for the stretching bands assigned to the grafted monomers remained constant and independent of the feed ratio of maleic anhydride to styrene. Thermal behaviour of the graft copolymers revealed that all graft copolymers exhibit single stage decomposition with characteristic transitions at 161–165°C and 290–300°C. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1763–1769, 1999     

Polymer–Metal Complexes Obtained by Radiation‐Induced Grafting Process onto Polyester Fabrics

Abstract

This paper reports the preparation of chelating copolymers via grafting of acrylic acid, and/or acrylamide onto polyester microfiber (PETMF) fabrics using a γ‐radiation technique. The effect of monomer concentration on the grafting process at irradiation dose 20?kGy was studied. The prepared graft chains (PETMF‐g‐AA), (PETMF‐g‐AAm), and (PETMF‐g‐PAAc/PAAm) acted as chelating sites for some selected transition metal ions. The effect of grafting on mechanical properties of PETMF and its copolymer–metal complexes was investigated. The prepared chelating copolymers and their metal complexes were characterized using x‐ray (energy dispersive x‐ray, EDX), differential scanning calorimeter (DSC), color parameters, and electrical conductivity measurements. The possibility of practical uses for such prepared graft copolymer–metal complexes was discussed and determined. The observed results showed that the electrical conductivity of the grafted copolymers and their metal complexes are thermally activated. Moreover, the degree of grafting enhanced the conductivity values of the grafted and non‐complexed copolymer up to three orders of magnitude, on the other hand, the conductivity of the copolymer–metal complexes slightly increased.     

Graft copolymerization kinetics of acrylic acid onto the poly(ethylene terephthalate) surface by atmospheric pressure plasma inducement

After one atmospheric pressure plasma treatment of poly(ethylene terephthalate) (PET) film, acrylic acid (AAc) in aqueous solution was successfully graft‐copolymerized onto PET films. The effects of reaction time, AAc monomer concentration and reaction temperature on grafting behavior of AAc were systematically studied. Possible reaction kinetics of plasma‐induced graft copolymerization, starting from initial hydroperoxide decomposition, were proposed. Through the Arrhenius analysis about graft copolymerization kinetics of AAc monomers on PET surface, it was revealed that the activation energies of decomposition, propagation and termination were 98.4, 63.5, and 17.5 kJ/mol, respectively. The temperature around 80 °C was favorable not only for the formation of oxide radicals through the thermal decomposition of hydroperoxide on PET surface but also for the extension of graft copolymer chain through direct polymer grafting. Poly(acrylic acid) (PAAc) grains grafted onto PET surfaces possessed relatively uniform size and both PAAc grain size and surface roughness increased with increasing the grafting degree of AAc. The increase of grain size with increasing grafting degree results from the possibility of forming long chain graft copolymers and their shielding of reactive sites. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1594–1601, 2008     

Potassium diperiodatonickelate‐initiated graft copolymerization of methyl acrylate onto organophilic montmorillonite

Using potassium diperiodatonickelate (Ni (IV)) as an efficient initiator, the graft copolymerization of methyl acrylate (MA) onto organophilic montmorillonite (OMMT) was successfully performed in an alkaline medium. Three grafting parameters were systematically evaluated as functions of the temperature, the initiator concentration, reaction time, pH value, and the ratio of MA to OMMT substrate. The structure of the titled graft copolymers (OMMT‐g‐PMA) were confirmed by Fourier transform infrared spectroscopy (FTIR), X‐ray diffraction (XRD), differential scanning calorimetry (DSC), and thermo‐gravimetric analysis (TGA). It was found that Ni (IV) was a highly efficient initiator for graft copolymerization of the MA onto OMMT, i.e., grafting efficiency is as high as 95% and grafting percentage can be facilely controlled within 700% in this study. In addition, the highest grafting efficiency and grafting percentage were obtained when temperature adopted was over 40°C and pH was about 10.3. A single‐electron‐transfer mechanism was proposed to illustrate the formation of radicals and the initiation reaction. Copyright © 2008 John Wiley & Sons, Ltd.     

聚四氟乙烯强酸性阳离子交换纤维的制备研究

采用共辐射引发将苯乙烯接枝到聚四氟乙烯(PTFE)纤维上,然后磺化制备出强酸性和超强酸性离子交换纤维,接枝率随苯乙烯单体浓度和辐射剂量增加而提高,随辐射剂量率的增加而降低,当接枝率为20%左右时,PTFE-co-St-SO3H离子交换纤维的Hammett酸度函数低于-11.99,呈现出超强酸性。     

Characterization of N-isopropyl acrylamide/acrylic acid grafted polypropylene nonwoven fabric developed by radiation-induced graft polymerization

Radiation-induced graft copolymerization of N-isopropylacrylamide (NIPAAm) and acrylic acid (AA) mixture was carried out on polypropylene nonwoven fabric to develop a thermosensitive material and has been found to affect the thermal and physical characteristics of fabric. The grafted fabrics with different monomer ratios were characterized by thermal gravimetric analysis (TGA), fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), X-ray diffraction (XRD), contact angle and atomic force microscopy (AFM). Results of FTIR clearly indicated that poly(acrylic acid) and poly(N-isopropyl acrylamide) were successfully grafted onto the membrane surface. TGA results showed that the thermal stability of PP fabric increased after grafting of NIPAAm/AA. The crystallinity values from DSC and XRD were found to decrease with increase in degree of grafting because of the addition of grafted chains within the noncrystalline region. The decrease in contact angles of the grafted fabric with an increase of the degree of grafting shows that PNIPAAm/PAA exists as the hydrophilic component. The increase in surface roughness after grafting was observed by AFM.     

Synthesis of perfluorinated cation exchange membranes by preirradiation grafting of acrylic acid onto ethylene-tetrafluoroethylene films

Hydrophilic carboxyl-containing fluoromembranes were obtained by preirradiation grafting of acrylic acid onto ethylene-tetrafluoroethylene film. The dependence of the grafting reaction on temperature, monomer concentration, nature and concentration of inhibitor, crosslinking agent, solvent, and on the preirradiation dose was investigated. The grafting rates increase with temperature, whereas the saturation degree of grafting (SDG) decreases. Addition of inhibitor minimizes homopolymerization and at the same time hinders the grafting reaction. The SDG increases markedly with monomer concentration until it reaches a maximum and thereafter decreases. The grafting rates increase with preirradiation dose. Addition of crosslinking agent initially decreases the SDG, and thereafter increases. The highest grafting rates are obtained using water as solvent followed by methanol and ethanol. The results are discussed on the basis of various parameters: interaction between monomer diffusibility and the viscosity of the monomer bath, the mutual reactivity of monomer, and the crosslinking agent. An agreement is observed between the values of the electrical resistance and the saturation degree of grafting. © 1996 John Wiley & Sons, Inc.     

Preirradiation grafting of N-vinyl-2-pyrrolidone onto poly(tetrafluoroethylene) and poly(tetrafluoroethylene-hexafluoropropylene) films

Preirradiation grafting of N-vinylpyrrolidone (NVP) onto poly(tetrafluoroethylene) (PTFE) and poly(tetrafluoroethylene-hexafluoropropylene) (FEP) films was investigated. The influence of grafting parameters such as preirradiation dose, monomer concentration, and grafting temperature on the rate and grafting yield was studied. Different solvents were used for diluting the monomer and it was found that the aqueous monomer solution at a concentration of 80 wt% was suitable for this grafting system. However, the graft polymerization of NVP in benzene terminated within a short time without significant grafting yield. The dependence of the grafting rate on preirradiation dose and monomer concentration was 1.2 and 1.07 order, respectively, for grafting onto PTFE films and 1.1 and 1.2 order, respectively, for grafting onto FEP films. Arrhenius plots for grafting onto PTFE films showed a breaking point at ca. 35°C and the overall activation energies were calculated as 23.6 and 9.0 Kcal/mol below and above 35°C, respectively. For grafting onto FEP films, however, no break was observed in the Arrhenius plots; the overall activation energy was 11.9 Kcal/mol. The swelling behavior and electric resistance of the grafted materials were investigated.     

Functionalization of polyesters with maleic anhydride by reactive extrusion

Maleic anhydride (MAn) was grafted onto aliphatic and aromatic/aliphatic copolyesters by reactive extrusion in the presence of a free radical initiator using a twin‐screw extruder. The grafting reaction was confirmed by spectroscopic analyses. The presence of succinic anhydride groups was shown by FT‐IR spectroscopy, and NMR spectra indicate that the grafts consist of single succinic anhydride units. The 2D ¹H‐NMR spectra (COSY) indicate that grafting reactions take place at aliphatic dicarboxylic acid units of copolyesters. The graft content was determined by a nonaqueous titration method. The effects of concentration of initiator and monomer and reaction temperature on the graft content and intrinsic viscosity were studied. The low percentage grafting in poly(lactic acid) was observed due to the presence of limited free radical sites in the polymer backbone. Temperature and monomer and initiator concentrations affect the graft content, and the desired graft content with minimal degradation can be obtained by controlling these factors. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 1693–1702, 1999     

Grafting vinyl monomers onto wool fibers. III. Graft copolymerization of methyl methacrylate onto wool using hexavalent chromium ion

The use of hexavalent chromium to initiate graft copolymerization of methyl methacrylate onto wool fibers has been investigated. The rate of grafting was determined by varying monomer, chromium(VI), temperature, acidity of the medium, nature of wool, reaction medium, and redox system. The graft yield increases with increasing monomer concentration up to 0.65M, and, with further increase of monomer the graft yield decreases. The graft yield increases with increasing chromium(VI) concentration. The grafting is considerably influenced by chemical modification of wool prior to grafting. The effect of certain inorganic salt and anionic surfactant on the rate of grafting has been investigated. The graft yield is influenced by thiourea concentration; it decreases with increasing thiourea concentration.     

Analysis and Characterization of Microwave Irradiation–Induced Graft Copolymerization of Methyl Methacrylate onto Delignified Grewia Optiva Fiber

Grafting of methyl methacrylate (MMA) onto delignified Grewia optiva fiber using ascorbic acid/H₂O₂ as an initiator was carried out under microwave irradiation. The effects of varying the microwave power, exposure time, and concentration of initiator and monomer of graft polymerization were studied to obtain maximum grafting percentage (26.54%). The experimental results showed that the optimal conditions for grafting were: exposure time, 10min; microwave power, 110 W; ascorbic acid concentration, 3.74mol/L × 10^?2; H₂O₂ concentration, 0.97mol/L × 10^?1; monomer concentration, 1.87mol/L × 10^?1. The graft copolymers were characterized by Fourier transform-infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM), and thermogravimetric analysis (TGA).     

Graft copolymerizations of gaseous vinyl chloride and vinylidene chloride on preirradiated polypropylene

The graft copolymerizations onto the preirradiated polypropylene fibers of gaseous vinyl chloride and also of gaseous vinylidene chloride were carried out. The fibers were preirradiated with γ-rays from a ⁶⁰Co source at ?78°C. in air to a total dose of 8 X 10⁵ rad, and were thus presumed to contain peroxide radicals which were active in grafting at ordinary temperature. The volume decrease of monomers at constant pressures due to the sorption and the grafting reaction was followed automatically at temperatures ranging from ?10 to 80°C. The net monomer consumption through the grafting process was estimated by subtracting the volume change due to the sorption from the total volume change of monomers. In general, the extent of grafting was lower at the higher grafting temperature and the decrease of the grafting activity of fibers was also accelerated. The grafting was found to increase almost linearly with the logarithm of the reaction time and the logarithm of the radiation of the radiation dose to the fibers. The extent of grafting was also proportional to the vapor pressure of monomer at a given reaction temperature and was supposed to be controlled by the amount of the monomer adsorbed. Raising the irradiation temperature higher than 0°C. brought about a marked decrease in the activity of preirradiated polypropylene. The grafting activity was successfully retained by the polymer for at least a fortnight at ?78°C.     

Graft copolymerization onto rubber. V. Graft copolymerization of methyl methacrylate onto rubber using potassium peroxydiphosphate as initiator

The graft copolymerization of methyl methacrylate onto natural rubber (NR) is investigated using potassium peroxydiphosphate as the initiator. The rate of grafting is determined by varying monomer concentration, peroxydiphosphate concentration, and temperature. The graft yield increased with an increase in monomer concentration up to 1.4082M/L and thereafter the graft yield decreases. The graft yield increases significantly with an increase of peroxydiphosphate concentration up to 150 X 10^-1M/L and thereafter the graft yield decreases. The grafting reaction is temperature dependent. A suitable kinetic scheme is proposed and the rate equation is evaluated.     

Radiation-induced grafting of styrene vapor to polyethylene

The radiation-induced grafting of styrene vapor to low-density polyethylene film of 0.063 mm thickness was studied at 23°C at a dose rate of 1.98 × 10⁴ rad/hr. The concentration C of monomer in the film was measured as a function of pre-irradiation exposure time to monomer vapor. The concentration-dependent diffusion coefficient of styrene in polyethylene was calculated to be 4.9 × 10^?9 exp {2.0C/C₀} cm²/sec, where C₀ is the saturation concentration of styrene in the film, and a linear boundary diffusion coefficient for styrene vapor into polyethylene film was found to be 2.0 × 10^?7 cm/sec. The rate of grafting was determined as a function of the concentration of styrene absorbed in the film. The maximum graft yield was obtained with an initial styrene concentration in the film of 4 wt-%. Under conditions of low initial monomer concentration, the grafting rate increases with irradiation time. The results are compared with previously published data on grafting of polyethylene from methanol–styrene solutions. They are explained in terms of the viscosity of the amorphous region as a function of styrene content and the resistance to the diffusion of monomer at the film–vapor interface.