CMC系列高分子表面活性剂与原油超低界面张力形成机理的研究

采用动态激光光散射及环境扫描电镜研究了羧甲基纤维素系列高分子表面活性剂与大庆原油形成超低界面张力的机理.结果表明,CMC系列高分子表面活性剂具有与低分子量表面活性剂相比拟的表/界面活性,其水溶液的表面张力可达2835mN/m,界面张力达到10^-110mN/m.碱的加入可显著降低高分子表面活性剂与原油的界面张力,在适当条件下界面张力达到超低值(10^-3mN/m),可望作为三次采油的驱油剂.等效烷烃模型研究表明,用碱与原油酸性组分的作用来解释碱能使界面张力下降至超低值的传统观点是不完善的,加入碱能使高分子表面活性剂胶束解缔,胶束数量增多,胶束粒径减小,单分子自由链增加,有利于高分子表面活性剂向界面迁移和排布,这是高分子表面活性剂和碱复配体系与原油界面张力下降至超低值的主要原因.     

植物油酸／Tween－60复配体系与原油间的界面张力

研究了植物油酸及其中和物／Ｔｗｅｅｎ－６０复配体系与大庆原油间界面张力随各种因素的变化规律。结果表明，当０．４０％ＮａＣｌ存在时，植物油酸中和度为０．８５，ＮａＣｌ浓度为０．９０％时，复配以０．１０％Ｔｗｅｅｎ－６０既可使体系兼容，又可使之保持较低界面张力。     

Interactions between synthetic and indigenous naphthenic acids and divalent cations across oil–water interfaces: effects of addition of oil-soluble non-ionic surfactants

Interactions between naphthenic acids and divalent metal cations across model oil–alkaline water interfaces were investigated by correlating changes in dynamic interfacial tension (IFT), to plausible reaction mechanisms. The measurements were carried out by using a CAM 200 optical instrument, which is based on the pendant drop technique. The naphthenic acids used were synthesised model compounds as well as commercial acid mixtures from crude distillation and extracted acid fractions from a North Sea crude oil. The divalent cations involved Ca²⁺, Mg²⁺, Sr²⁺, and Ba²⁺, which are all common in co-produced formation water and naphthenate deposits. The results show that the dynamic IFT strongly depends on naphthenic acid structure, type of divalent cation, and the concentration of the compounds as well as the pH of the aqueous phase. Introducing divalent cations to systems involving saturated naphthenic acids caused mostly a permanent lowering of the IFT. The decline in IFT is due to electrostatic attraction forces across the interface between the cations in the aqueous phase and the carboxylic-groups at the o/w interface, which cause a higher interfacial density of naphthenic acid monomers. The permanent lowering in IFT is likely due to formation of positively charged monoacid complexes, which possess high interfacial activity. On the other hand, in the case of the aromatic model compounds, the cations affected the IFT differently. This is mainly discussed in light of degree of cation hydration and steric conditions. Various oil-soluble non-ionic surfactant mixtures were also introduced to systems involving a model naphthenic acid and Ca²⁺ in order to investigate how the interfacial competition affected the local interactions. Based on the behaviour of dynamic IFT, probable inhibition mechanisms are discussed.Electronic Supplementary Material Supplementary material is available for this article at     

Experimental Study of the Effect of Strong Alkali on Lowering the Interfacial Tension of Oil/Heavy Alkylbenzene Sulfonates System

Experimental studies were conducted to explore the fundamental mechanisms of alkali to lower the interfacial tension of oil/heavy alkylbenzene sulfonates (HABS) system. Sodium hydroxide was used as the strong alkali chemical to investigate the interfacial tension (IFT) of oil/HABS system. The influences of salt and alkali on the interfacial activity were studied by the measurement of interfacial tension and partition coefficient. Moreover, the alkali/surfactant solutions were measured by dynamic laser scattering. The results showed that compared with the salt, the function of alkali to lower the interfacial tension and improve partition coefficient is more significant. The micelles formed by surfactants could be disaggregated because of adding alkali, so the size of micelles decreases and the number of mono‐surfactants increases, then more surfactant molecules move to the interface of oil/surfactant system and the adsorption of surfactants at oil‐water interfaces increases, which can lead to the decrease of IFT.     

Interfacial activity of a novel family of polymeric surfactants

A novel series of polymeric surfactants based on carboxy methyl cellulose and alkyl poly(etheroxy) acrylate were synthesized by ultrasonic irradiation. These polymeric surfactants have exhibit excellent surface activity due to their unique structure. The influences of salt, alcohol and alkali on the interfacial activity of these polymeric surfactants were studied by interfacial tensiometery, dynamic laser scattering (DLS), UV spectroscope and environmental scanning electrical microscope (ESEM). The surface tension and interfacial tension (IFT) properties change little with NaCl added. The formed micelles shrink, their size becomes smaller. Alcohols cause the IFT to decrease a little because a small amount of free chains present in solution. Under the influence of added alkali, the IFT of the polymeric surfactants, in aqueous solution, decreases so much that sometimes it is less than 10⁻² mN/m. Using data from the equivalent alkane scan, one cannot draw the conclusion that the action of alkali with the acidic components in crude oil leads to the ultra-low IFT. The analyses by UV, DLS and ESEM show that the micelles formed by polymeric surfactants could be disaggregated or destroyed sharply by the action of alkali. So the size of micelles decreases greatly and the number of free chains increases. That more polymeric surfactants molecules move to the interface of oil/water and rearrange at the interface of oil/water is believed to be the main reason of the ultra-low IFT (10⁻³ mN/m) that is obtained.     

Effects of a Novel Organic Alkali on the Interfacial Tension and Emulsification Behaviors Between Crude Oil and Water

Experiments have been carried out to investigate the interfacial tension (IFT) and emulsification behaviors between Shengli crude oil and a novel organic alkali (OA). The dynamic IFT and minimum IFT are adopted to characterize the IFT behaviors; the microscopic method, Turbiscan stability index, separated water rate, and laser particle size analysis method are used to show the emulsification behaviors. The dynamic and minimum IFT both decrease continuously with the increase of OA concentration whether surfactant is added or not; because of the synergy of OA and surfactant, the minimum IFT will be reduced to the ultralow value. The synergy is also crucial for the crude oil emulsification. When OA and surfactant are used together, owing to the mosaic and cross-multiple adsorption of OA, surfactant and in situ soap at the interfacial film, the oil can be emulsified more easily, the quantity of emulsified droplets is higher, and the emulsion is more stable with OA concentration increases. The relationship of the minimum IFT and emulsification is investigated; it indicates that the emulsion stability improves, the degree of dispersed homogeneity of oil droplets increases, and the median diameter of emulsified oil droplets decreases with the decline of the minimum IFT.     

Study on the Interfacial Tensions Between Oils and Alkylbenzene Sulfonate Gemini Surfactant Solutions

Interfacial tensions (IFT) of five alkylbenzene sulfonate Gemini surfactants Ia, Ib, Ic, Id, and Ie at different oils/water systems were measured by a spinning drop interfacial tensiometer. And critical micelle concentration (CMC), the interfacial tension at CMC (γ_CMC), maximum interfacial excess concentration (Γ _max) and the surface area per molecule (A_min) were calculated. The results indicated that the CMC values determined with interfacial tension method were lower than those determined with surface tension method. And γ_CMC for Ie is larger than that for Ia, Ib, Ic, and Id. In addition, the effects of temperature and hydrophobic chains on dynamic IFT were also studied. With the increment of temperature, dynamic IFT is easier to reach a stable value. However, with the increment of hydrophobic chains, dynamic IFT is more difficult to reach a stable value. Each Gemini surfactant produces a minimum IFT when measured against a different n-alkane.     

Effect of Polymer on Dynamic Interfacial Tensions of Anionic–nonionic Surfactant Solutions

The dynamic interfacial tensions (IFTs) of enhanced oil recovery (EOR) surfactant/polymer systems against n-decane have been investigated using a spinning drop interfacial tensiometer in this paper. Two anionic–nonionic surfactants with different hydrophilic groups, C₈PO₆EO₃S (6-3) and C₈PO₆EO₆S (6-6), were selected as model surfactants. Partially hydrolyzed polyacrylamide (HPAM) and hydrophobically modified polyacrylamide (HMPAM) were employed. The influences of surfactant concentration, temperature, polymer concentration, and oleic acid in the oil on IFTs have been studied. The experimental results show that anionic–nonionic surfactants can form compact adsorption films and reach ultralow IFT (10^?3 mN/m) under optimum conditions. The addition of polymer has great influence on dynamic IFTs between surfactant solutions and n-decane mainly by the formation of looser mixed films resulting from the penetration of polymer chains into the interface. The compact surfactant film will also be weakened by the competitive adsorption of oleic acid, which results in the increase of IFT. Moreover, the penetration of polymer chains will be further destroyed surfactant/polymer mixed layer and lead to the obvious increase of IFT. On the other hand, polymers show little effect on the IFTs of 6-6 systems than those of 6-3 because of the hindrance of longer EO chain of 6-6 at the interface.     

高盐油藏下两性/阴离子表面活性剂协同获得油水超低界面张力

研究了在高盐油藏中, 利用两性/阴离子表面活性剂的协同效应获得油水超低界面张力的方法. 两性表面活性剂十六烷基磺基甜菜碱与高盐矿化水具有很好的相容性, 但在表面活性剂浓度为0.07%-0.39%(质量分数)范围内仅能使油水界面张力达到10^-2 mN·m^-1量级, 加入阴离子表面活性剂十二烷基硫酸钠后则可与原油达到超低界面张力. 通过探讨表面活性剂总浓度、金属离子浓度、复配比例对油水动态界面张力的影响, 发现两性/阴离子表面活性剂混合体系可以在高矿化度、低浓度和0.04%-0.37%的宽浓度范围下获得10^-5 mN·m^-1量级的超低界面张力, 并分析了两性/阴离子表面活性剂间协同获得超低界面张力的机制.     

Studies of synergism/antagonism for lowering dynamic interfacial tension in surfactant/alkali/acidic oil systems. 3. Synergism/antagonism in surfactant/alkali/acidic model oil systems

Experimental studies have been conducted to elucidate the mechanisms responsible for synergism/antagonism for lowering dynamic interfacial tension (IFT) in surfactant/alkali/hydrocarbon and surfactant/alkali/acidic model oil systems. Dynamic IFTs between hydrocarbon/acidic model oil and alkali/surfactant solutions were measured. We learned from our experimental results that alkali has the function of decreasing n(min) values of surfactant solutions. The synergism/antagonism for lowering the stable values of dynamic IFTs in surfactant/alkali/hydrocarbon and surfactant/alkali/acidic model oil systems depends on factors that can change the EACN/n(min) value, such as the oleic acid in the oil phase and the n(min) values of surfactant and alkali. A new explanation with respect to EACN/n(min) values is provided.     

Ultra-Low Interfacial Tension Between Heavy Oil and Betaine-Type Amphoteric Surfactants

Betaine surfactants with lipophilic groups of different lengths were synthesized in this research and the dynamic interfacial tension (IFT) between solutions of these surfactants and three kinds of crude oil from Shengli Oilfield are measured. The results indicated that, for Gudao and Gudong heavy oil, cetyl dimethyl hydroxyl sulfobetaine (SBET-16) was the most efficient in lowering the IFT in the case of no alkalis, while for Shengtuo heavy oil, cetyl dimethyl carboxymethyl betaine (CBET-16) was best. SBET-16 with the concentration of 0.003–0.1% and 0.005–0.1% can reduce the oil/water IFT to ultra-low for Gudao and Gudong oil respectively, CBET-16 with the concentration of 0.005–0.1% can lower the oil/water IFT to ultra-low for Shengtuo oil. These results showed that for different oils, an oil displacement agent with high capacity to lower the oil/water interfacial tension may be obtained only by changing the molecular structure of betaine surfactant. This study can be used to guide the design of surfactants for alkaline-free combination flooding.     

Study on the Mechanism of Asphaltenes Reducing Oil-Water Interfacial Tension

As high polar components of crude oil, asphaltenes play a significant role in reducing oil-water interfacial tension(IFT). In this paper, the effects of asphaltenes on reducing IFT in the presence of surfactant were compared, and the mechanism of asphaltenes reducing the IFT was studied by the dynamic interfacial tension(DIFT) equation. Whether asphaltenes were added to the oil or 2,5-dimethyl-4-(4-dodecyl) benzene sodium sulfonate(p-S14-4) was added to the water phase, either of all results in the IFT reducing and the IFT is related to the coverage and the mass of asphaltenes adsorption at the interface. In the presence of asphaltenes, the adsorption of the active substances to the interface is not entirely dependent on diffusion, and the process can be divided into three regions. Region I: the IFT rapidly reducing, this process is controlled by diffusion of surfactant; Region II: the IFT reducing slowly, resulted from the lower diffusion rate that is limited due to the aggregates formed by the interaction of asphaltene-asphaltene; Region III: the interaction of asphaltene-asphaltene is broken by the interaction of surfactant-asphaltene. The asphaltene aggregates are reduced and adsorbed rapidly at the interface. Furthermore, the results reveal that the asphaltenes concentration affects the coverage rate and adsorption at the interface.     

油酸-油酸钠水溶液/原油间的瞬时界面张力

羧酸盐表面活性剂以其价格低廉、资源丰富和较高的界面活性而受到重视[1]．我们将廉价的天然核酸盐复配体系用于提高采收率研究，取得良好效果问．据最近报道问，用瞬时界面张力（l）评价驱油体系更符合实际采油过程．本文应用试剂级油酸，试图从理论上探讨不同因素对混合体系瞬时界面张力的影响规律，为驱油体系配方的选择提供依据．1实验部分1．1试剂油酸（R17C00H），分析纯收京长城化学试剂厂产品）．水解聚丙烯酸胶（HPAM），平均分子量为1．7X10’，平均水解度为20％，（美国辉瑞公司产品）．1．2方法按设计量在电子分析天平（精…     

三元复合驱碱/表面活性剂/聚合物模拟原油乳状液稳定动力学特性

基于两相分离的乳状液稳定模型,研究了三元复合驱模拟原油乳状液稳定动力学特性;通过液膜强度和油水界面张力探讨了碱/表面活性剂/聚合物对模拟原油乳状液稳定动力学特性的影响机理。 结果表明,乳状液稳定模型可以很好的评价乳状液的稳定性,并得到乳状液的稳定动力学特性;碱浓度小于900 mg/L有利于乳状液的稳定,碱浓度大于900 mg/L不利于乳状液的稳定;表面活性剂和聚合物浓度的增加使得形成的模拟原油乳状液更加稳定;模拟原油乳状液的稳定作用主要是通过碱、表面活性剂降低油水界面张力并增加油水界面膜强度,聚合物通过提高界面膜强度实现的,三者存在协同效应。     

Model Compounds for Asphaltenes and C80 Isoprenoid Tetraacids. Part I: Synthesis and Interfacial Activities

Three model compounds for asphaltenes and two model compounds for the C₈₀ isoprenoid tetraacids (ARN) have been synthesized and their interfacial and solubility properties were investigated. All compounds exhibit high interfacial activities. The asphaltene models lowered the interfacial tension between toluene and pH 9 to around 5 mN/m at 12.5–35 μM and the tetraacid models gave a drop in the interfacial tension between chloroform and pH 9 to 13 mN/m at only 5 μM, which is consistent with previous findings for the natural occurring C₈₀ tetraacids. A sudden drop in the IFT over a very narrow concentration range was observed for two of three asphaltene models. NIR spectroscopy studies indicated an aggregation most likely a result of polar and hydrogen bond interactions. The IFT results also showed different behavior with only small changes in chemical structure. The tetraacid models have similar interfacial behavior as the C₈₀ tetraacids and will thus be suitable model compounds with their highly UV active and fluorescent properties.     

Enhanced heavy oil recovery by organic alkali combinational flooding solutions

Although alkaline/surfactant/polymer (ASP) flooding is successfully applied in oil fields, some disadvantages such as scales, corrosion effects, and viscosity reductions of polymer solutions appear. Usage of organic alkalis can avoid or decrease these disadvantages. In this paper, the physicochemical properties, including interfacial tension (IFT), and viscosity, of organic alkali combinational flooding solutions and their effectiveness as enhanced oil recovery agents are investigated. Monoethanolamine (MEA) is the optimal one for decreasing the IFT among the three organic alkalis studied in this paper. Although MEA cannot decrease the IFT as low as NaOH does, it has good compatibility with both surfactant and the polymer hydrolyzed polyacrylamide (HPAM). MEA not only helps a surfactant solution or HPAM/surfactant mixture attain ultralow IFT values, but can also promote better viscosity stability for HPAM or HPAM/surfactant solutions compared to NaOH. Moreover, core flood experiments show that adding MEA can obtain additional tertiary oil recovery of 6%–10% original oil in place (OOIP) on the top of HPAM or HPAM/surfactant flooding, although MEA has a lower enhanced oil recovery than NaOH. The experimental results show that MEA is a good choice to replace NaOH in enhancing heavy oil recovery.     

新型磺基甜菜碱/聚丙烯酰胺体系表面及界面性能

采用自制的新型磺基甜菜碱两性表面活性剂与相对分子质量2500万的聚丙烯酰胺进行复配,考察了不同温度和矿化度条件下,聚合物对复配溶液表面、界面性能的影响。 采用滴体积法测定了溶液的表面张力,结果表明,加入聚合物使溶液的临界胶束浓度增大,且复配溶液的表面张力大于单独表面活性剂溶液的表面张力。 当聚合物浓度一定,增大溶液矿化度时,体系表面张力增大。 用旋滴型界面张力仪测定了溶液的界面张力,结果表明,增大聚合物浓度,油水界面张力增大,增大溶液矿化度,油水界面张力有所升高。 聚合物质量浓度为1.5 g/L,表面活性剂质量浓度为0.3 g/L时,可使胜利油田孤岛原油和孤东原油的油水界面张力达到超低数量级（10-3 mN/m）。 用分水时间法测定了溶液的乳化性能,结果表明,聚合物浓度增大,分水时间延长,并考察了75、85和95 ℃条件下体系的乳化性能,温度越高,分水时间越短。     

Synergistic effect of mixed anionic and cationic surfactant systems on the interfacial tension of crude oil-water and enhanced oil recovery

Surfactant based enhanced oil recovery (EOR) is an interesting area of research for several petroleum researchers. In the present work, individual and mixed systems of anionic and cationic surfactants consisting of sodium dodecyl sulphate (SDS) and cetyltrimethylammonium bromide (CTAB) in different molar ratios were tested for their synergistic effect on the crude oil-water interfacial tension (IFT) and enhanced oil recovery performance. The combination of these two surfactant systems showed a higher surface activity as compared to individual surfactants. The effect of mixed surfactant systems on the IFT and critical micellar concentration (CMC) is strongly depends on molar ratios of the two surfactant. Much lower CMC values were observed in case of mixed surfactant systems prepared at different molar ratios as compared to individual surfactant systems. The lowest CMC value was found when the molar concentration of SDS was higher than the CTAB. When the individual and mixed surfacant systems were tested for EOR performance through flooding experiments, higher ultimate oil recovery was obtained from mixed surfactant flooding compared to individual surfactants. Combination of SDS and CTAB or probably other anionic-cationic surfactants show synergism with substantial ability to reduce crude oil water IFT and can be a promising EOR method.     

The relative role of coalescence and interfacial tension in controlling dispersed phase size reduction during the compatibilization of polyethylene terephthalate/polypropylene blends

The breaking thread and the sessile drop methods have been used to evaluate the interfacial tension between a polypropylene (PP) and a polyethylene-terephthalate (PET). An excellent correlation was found between the two. The breaking thread technique was then used to evaluate the interfacial tension of these blends at various levels of a styrene-ethylene butylene-styrene grafted with maleic anhydride (SEBS-g-MA) compatibilizer. In order to evaluate the relative roles of coalescence and interfacial tension in controlling dispersed phase size reduction during compatibilization, the morphology of PP/PET 1/99 and 10/90 blends compatibilized by a SEBS-g-MA were studied and compared. The samples were prepared in a Brabender mixer. For the 10/90 blend, the addition of the compatibilizer leads to a typical emulsification curve, and a decrease in dispersed phase size of 3.4 times is observed. For the 1/99 blend, a 1.7 times reduction in particle size is observed. In the latter case, this decrease can only be attributed to the decrease of the interfacial tension. It is evident from these results that the drop in particle size for the 10/90 PP/PET blend after compatibilization is almost equally due to diminished coalescence and interfacial tension reduction. These results were corroborated with the interfacial tension data in the presence of the copolymer. A direct relationship between the drop in dispersed phase size for the 1/99 PP/PET blend and the interfacial tension reduction was found for this predominantly shear mixing device. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35 : 2271–2280, 1997     

Studies of synergism for lowering dynamic interfacial tension in sodium alpha-(n-alkyl) naphthalene sulfonate/alkali/acidic oil systems

Alkylnaphthalene sulfonates with high purity were selected as model components to research synergism for lowering interfacial tension (IFT) in surfactant/alkali/acidic oil systems. The dynamic IFTs between alkylnaphthalene sulfonates with different alkyl chain length and n-decane, oleic acid model oil, or Shengli crude oil were measured. The results showed that the alkylnaphthalene sulfonates with different alkyl chain lengths had different synergism with different acidic components and their ionized acids under the same conditions. The synergism for lowering dynamic IFT in alkylnaphthalene sulfonate/alkali/acidic oil systems was controlled by alkylnaphthalene sulfonate concentration, alkyl chain length, alkali concentration, alkali type, and oleic acid concentration: optimal physicochemical conditions were necessary to the best synergism. This indicates that the synergism among added surfactant acidic components in crude oil and their ionized acids is controlled by the ratio of their interfacial concentrations.