Spray pyrolysis-deposited TiO<Subscript>2</Subscript> thin films as high-performance lithium ion battery anodes

Focusing on additive-free electrodes, thin films are of typical interest as electrodes for lithium ion battery application. Herein, we report the fabrication of TiO₂ thin films by spray pyrolysis deposition technique. X-ray diffraction and transmission electron microscopic analysis confirms the formation of anatase TiO₂. Electrochemical evaluation of these sub-micron TiO₂ thin films exhibits high-rate performance and long cycling stability. At 1C rate (1C?=?335 mA/g), the electrode delivered discharge capacity of 247 mAh/g allowing about 0.74 lithium into the structure. The electrodes also delivered specific capacities of 122 and 72 mAh/g at 10 and 30C rates, respectively. Without conductive additives, this excellent performance can be attributed to the nanosize effect of TiO₂ particles combined with the uniform porous architecture of the electrode. Upon cycling at high rates (10 and 30C), the electrode exhibited excellent cycling stability and retention, specifically only <?0.6% capacity loss per cycle over 2500 cycles.     

Effect of deposition time on structural and physical properties of Cu<Subscript>2</Subscript>CdSnS<Subscript>4</Subscript> thin films prepared by spray pyrolysis technique: experimental and ab initio study

Cu₂CdSnS₄ (CCdTS) thin films were synthesized using chemical spray pyrolysis deposition technique. The effect of various deposition times (20, 40, 60 min) on growth of these films was investigated. The as-synthesized Cu₂CdSnS₄ thin films were characterized by X-ray diffraction (XRD), ultraviolet–visible (UV–Vis) spectroscopy, Raman spectroscopy and Hall Effect measurements. The XRD pattern of Cu₂CdSnS₄ structured in stannite phase with preferential orientations along (112) planes. Raman spectrum revealed very strong peak at about 333 cm^?1. The films have the direct optical band gaps of 1.39–1.5 eV. The optimum hole mobility was found to be 3.212 × 10¹ cm² v^?1 s^?1 for the film deposited on 60 min. The electronic structure and optical properties of the stannite structure Cu₂CdSnS₄ were obtained by ab initio calculations using the Korringa–Kohn–Rostoker method combined with the Coherent Potential Approximation (CPA), as well as CPA confirms our results.     

The effect of argon gas pressure on structural,morphological and photoluminescence properties of pulsed laser deposited KY<Subscript>3</Subscript>F<Subscript>10</Subscript>:Ho<Superscript>3+</Superscript> thin films

KY₃F₁₀:Ho³⁺ thin films were deposited by a pulsed laser deposition technique with Nd–YAG laser radiation (λ = 266 nm) on (100) silicon substrate. The XRD and FE-SEM results show improved crystalline structure for the film deposited at a pressure of 1 Torr. The AFM results show that the RMS roughness of the films increases with rise in argon gas pressure. The EDS elemental mapping shows Y-excess for all the films deposited under all pressures, and this is attributed to its higher mass and low volatility as compared to K and F. XPS analysis further confirmed Y-excess in the deposited films. Green PL emission at 540 nm was investigated at three main excitation wavelengths, namely 362, 416 and 454 nm. The PL emission peaks increase with rise in background argon gas pressure for all excitation wavelengths. The highest PL intensity occurred at excitation of 454 nm for all the thin films. In addition, faint red (near infrared) emission was observed at 750 nm for all the excitations. The green emission at 540 nm is ascribed to the ⁵F₄–⁵I₈ and ⁵S₂–⁵I₈ transitions, and the faint red emission at 750 nm is due to the ⁵F₄–⁵I₇ and ⁵S₂–⁵I₇ transitions of Ho³⁺.     

Nanocrystalline Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> electrodes for supercapattery application

Nanocrystalline Li₂TiO₃ was successfully synthesized using solid-state reaction method. The microstructural and electrochemical properties of the prepared material are systematically characterized. The X-ray diffraction pattern of the prepared material exhibits predominant (002) orientation related to the monoclinic structure with C2/c space group. HRTEM images and SAED analysis reveal the well-developed nanostructured particles with average size of ～40 nm. The electrochemical properties of the prepared sample are carried out using cyclic voltammetry (CV) and chronopotentiometry (CP) using Pt//Li₂TiO₃ cell in 1 mol L^?1 Li₂SO₄ aqueous electrolyte. The Li₂TiO₃ electrode exhibits a specific discharge capacity of 122 mAh g^?1; it can be used as anode in Li battery within the potential window 0.0–1.0 V, while investigated as a supercapacitor electrode, it delivers a specific capacitance of 317 F g^?1 at a current density of 1 mA g^?1 within the potential range ?0.4 to +0.4 V. The demonstration of both anodic and supercapacitor behavior concludes that the nanocrystalline Li₂TiO₃ is a suitable electrode material for supercapattery application.     

Studies of Nanosized Iron-Doped TiO<Subscript>2</Subscript> Photocatalysts by Spectroscopic Methods

Iron-doped TiO₂ nanoparticles with iron content in the range of 0.005 < Fe/Ti < 0.3 were prepared using the flame spray pyrolysis method and investigated with CW X-band electron paramagnetic resonance (EPR), X-ray diffraction, and Fourier transform infrared spectroscopy. This allowed for the clarification of the internal organization of Fe–TiO₂ nanoparticles. Different types of Fe(III) centers were distinguished in the samples: isolated high-spin paramagnetic Fe(III) ions (S = 5/2) in rhombic ligand fields state at 0.005 < Fe/Ti < 0.05, and Fe(III) ferromagnetic clusters at Fe/Ti < 0.1. All Fe-doped samples had rather high activity for the photocatalytic mineralization of oxalic acid under visible light illumination (λ > 400 nm) at 25 °C. Correlations were made between EPR and photocatalytic activity results. The specific surface area [S] data allowed us to deduce that the isolated Fe(III) centers were responsible for the photomineralisation of oxalic acid, while the Fe(III) ferromagnetic aggregates decreased the total efficiency of the system.     

Optical and structural properties of PbI<Subscript>2</Subscript> thin film produced via chemical dipping method

PbI₂ thin films were deposited on glass substrates via chemical bath deposition. The characteristics of PbI₂ thin films were examined through their structural and optical properties. X-ray diffraction spectra showed the presence of rhombohedral structure and atom planes were subject to change with the pH of the bath. Scanning electron microscope indicated uniform distribution of grains. Optical properties were examined via UV–VIS; optical spectrum of the thin films was measured at the range of 200–1100 nm wavelength. Optimum pH levels for producing thin films were found to be pH 4–5. It has been observed that transmission and optical band gap (E _g) increased with the pH of the bath, which varied between 66–95 and 2.24–2.50 %, respectively; on the other hand film thickness of PbI₂ thin films was decreased with the pH of the bath. Energy-dispersive X-ray spectroscopy analysis were in accordance with theoretical value of PbI₂ at pH = 4 and 5. Refractive index was negatively correlated with pH of the chemical bath; it has been calculated as 1.97, 1.40, 1.29 and 1.24 for the films produced at pH 2, 3, 4 and 5. The results of the study were compared with similar studies in the literature.     

Gamma irradiation effects on structural and optical properties of amorphous and crystalline Nb<Subscript>2</Subscript>O<Subscript>5</Subscript> thin films

The structural and optical properties of RF sputtered Nb₂O₅ thin films are studied before and after gamma irradiation. The films are subjected to structural and surface morphological analyses by using X-ray (XRD) and field emission scanning electron microscope techniques. In the wavelength range of 300–2000 nm, the optical parameters for amorphous and crystalline Nb₂O₅ thin films are estimated at differently exposed γ-irradiation doses (0, 50, 100 and 200 kGy). The optical constants, such as optical energy band gap, absorption coefficient, refractive index and oscillators parameters of amorphous and crystalline Nb₂O₅ thin films are calculated. The optical band gaps of γ-irradiated amorphous and crystalline Nb₂O₅ thin films are determined. In the non-absorbing region, the real part of the refractive index of amorphous and crystalline Nb₂O₅ thin films slightly increases with the increase in the exposed γ-irradiation dose.     

Thickness dependent optical properties of titanium oxide thin films

TiO₂ thin films of different thickness were prepared by the Electron Beam Evaporation (EBE) method on crystal silicon. A variable angle spectroscopic ellipsometer (VASE) was used to determine the optical constants and thickness of the investigated films in the spectral range from 300 to 800 nm at incident angles of 60°, 70°, and 75°, respectively. The whole spectra have been fitted by Forouhi–Bloomer (FB) model, whose best-fit parameters reveal that both electron lifetime and band gap of TiO₂ thin film have positive correlation to the film thickness. The refractive indices of TiO₂ thin film increase monotonically with an increase in film thickness in the investigated spectral range. The refractive index spectra of TiO₂ thin films have maxima at around 320 nm and the maxima exhibit a marginally blue-shift from 327.9 to 310.0 nm with an increase in film thickness. The evolution of structural disorder in the TiO₂ thin film growth can be used to explain these phenomena.     

High-temperature complex impedance and modulus spectroscopic studies of doped Na<Subscript>0.5</Subscript>Bi<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript>-BaTiO<Subscript>3</Subscript> ferroelectric ceramics

Lead-free Na_0.5Bi_0.5TiO₃ (NBT) and (1 ? x)Na_0.5Bi_0.5TiO₃ + xBaTiO₃ with x = 0.1 and 0.2 (where x = 0.1 and 0.2 are named as NBT1 and NBT2, respectively), (1 ? y)Na_0.5Bi_0.5TiO₃ + yBa_0.925Nd_0.05TiO₃ with y = 0.1 and 0.2 (where y = 0.1 and 0.2 are named as NBT3 and NBT4, respectively)-based relaxor ferroelectric ceramics were prepared using the sol-gel method. The crystal structure was investigated by X-ray diffraction (XRD) at room temperature (RT). The XRD patterns confirmed the presence of the rhombohedral phase in all the samples. The electrical properties of the present NBT-based samples were investigated by complex impedance and the modulus spectroscopy technique in the temperature range of RT–600 °C. The AC conductivity was found to increase with the substitution of Ba²⁺ ions to the NBT sample whereas it significantly decreased with the addition of Nd³⁺ ions. The more anion vacancies in Ba-added samples and the lower anion vacancies in Nd-added samples were found to be responsible for higher and lower conductivities, respectively.     

Fast electrochromic response of porous-structured cobalt oxide (Co<Subscript>3</Subscript>O<Subscript>4</Subscript>) thin films by novel nebulizer spray pyrolysis technique

Electrochromic effect of cobalt oxide thin films was studied as a function of substrate temperature (573–673 K). Tricobalt tetraoxide (Co₃O₄) thin films were deposited on glass and fluorine-doped tin oxide (FTO) substrates by nebulized spray technique using cobalt nitrate as precursor material. The XRD patterns indicated (311) plane was dominant for all the films irrespective of the deposition temperature. Williamson-Hall (W-H) analysis was made to understand the strain variation in the prepared Co₃O₄ films under different deposition temperature by employing uniform deformation model (UDM). Scanning electron microscopy images revealed porous morphology for the film prepared at 623 K. The optical parameters such as refractive index (n), extinction coefficient (k), and band gap were derived from UV-visible spectra of Co₃O₄ films. The electrochromic performance of the deposited Co₃O₄ films was analyzed through cyclic voltammetry, chronocoulometry, chronoamperometry, and iono-optical studies.     

Semiconducting SnO<Subscript>2</Subscript>-TiO<Subscript>2</Subscript> (S-T) composites for detection of SO<Subscript>2</Subscript> gas

SnO₂-TiO₂ (S-T) composites with different molar ratios were prepared by mechanical mixing followed by sintering at 700 °C for 4 h in air. The structural and microstructural properties of the composites were investigated using powder X-ray diffraction (PXRD) and scanning electron microscopy (SEM). S-T composites were investigated by introducing SO₂ to test their chemical stability using PXRD and SEM coupled with energy dispersive X-ray (EDX) analysis. The sensing performance was measured at different temperatures using various SO₂ concentrations (10–100 ppm). A composite comprising 25 mol% of SnO₂ and 75 mol% TiO₂ (S25-T75) exhibited the highest sensitivity comparing to other S-T composites studied under the presently investigated conditions. t ₉₀ (90 % of response time) was found to be ～5 min for thick pellet (~2 mm in thickness). SO₂ sensing mechanism has been explained through the band structure model.     

Anatase TiO<Subscript>2</Subscript> nanoparticles for lithium-ion batteries

Anatase TiO₂ nanoparticles were prepared by a simple sol-gel method at moderate temperature. X-ray powder diffraction (XRD) and Raman spectroscopy revealed the exclusive presence of anatase TiO₂ without impurities such as rutile or brookite TiO₂. Thermogravimetric analysis confirmed the formation of TiO₂ at about 400 °C. Particle size of about 20 nm observed by transmission electron microscopy matches well with the dimension of crystallites calculated from XRD. The electrochemical tests of the sol-gel-prepared anatase TiO₂ show promising results as electrode for lithium-ion batteries with a stable specific capacity of 174 mAh g^?1 after 30 cycles at C/10 rate. The results show that improvement of the electrochemical properties of TiO₂ to reach the performance required for use as an electrode for lithium-ion batteries requires not only nanosized porous particles but also a morphology that prevents the self-aggregation of the particles during cycling.     

Photoactivity passivation of TiO<Subscript>2</Subscript> nanoparticles using molecular layer deposited (MLD) polymer films

Pigment-grade anatase TiO₂ particles (160 nm) were passivated using ultra-thin insulating films deposited by molecular layer deposition (MLD). Trimethylaluminum (TMA) and ethylene glycol (E.G) were used as aluminum alkoxide (alucone) precursors in the temperature range of 100–160 °C. The growth rate varied from 0.5 nm/cycle at 100 °C to 0.35 nm/cycle at 160 °C. Methylene blue oxidation tests indicated that the photoactivity of pigment-grade TiO₂ particles was quenched after 20 cycles of alucone MLD film, which was comparable to 70 cycles of Al₂O₃ film deposited by atomic layer deposition (ALD). Alucone films would decompose in the presence of water at room temperature and would form a more stable composite containing aluminum, which decreased the passivation effect on the photoactivity of TiO₂ particles.     

Influence of nanocrystalline structure and composition on hardness of thin films based on TiO<Subscript>2</Subscript>

In this work, the influence of Tb-doping on structure, and especially hardness of nanocrystalline TiO₂ thin films, has been described. Thin films were formed by a high-energy reactive magnetron sputtering process in a pure oxygen atmosphere. Undoped TiO₂-matrix and TiO₂:Tb (2 at. % and 2.6 at. %) thin films, had rutile structure with crystallite sizes below 10 nm. The high-energy process produces nanocrystalline, homogenous films with a dense and close packed structure, that were confirmed by X-ray diffraction patterns and micrographs from a scanning electron microscope. Investigation of thin film hardness was performed with the aid of a nanoindentation technique. Results of measurements have shown that the hardness of all manufactured nanocrystalline films is above 10 GPa. In the case of undoped TiO₂ matrix, the highest hardness value was obtained (14.3 GPa), while doping with terbium results in hardness decreasing down to 12.7 GPa and 10.8 GPa for TiO₂:(2 at. % Tb) and TiO₂:(2.6 at. % Tb) thin films, respectively. Incorporation of terbium into TiO₂-matrix also allows modification of the elastic properties of the films.     

Ion beam sputter deposition of TiO<Subscript>2</Subscript> films using oxygen ions

TiO₂ thin films were grown by ion beam sputter deposition (IBSD) using oxygen ions, with the ion energy and geometrical parameters (ion incidence angle, polar emission angle, and scattering angle) being varied systematically. Metallic Ti and ceramic TiO₂ served as target materials. The thin films were characterized concerning thickness, growth rate, surface topography, structural properties, mass density, and optical properties. It was found that the scattering geometry has the main impact on the film properties. Target material, ion energy, and ion incidence angle have only a marginal influence. Former studies on reactive IBSD of TiO₂ using Ar and Xe ions reported equivalent patterns. Nevertheless, the respective ion species distinctively affects the film properties. For instance, mass density and the refractive index of the TiO₂ thin films are remarkably lower for sputtering with oxygen ions than for sputtering with Ar or Xe ions. The variations in the thin film properties are tentatively attributed to the angular and the energy distribution of the film-forming particles, especially, to those of the backscattered primary particles.     

Nanostructured TiO<Subscript>2</Subscript> Films with a Mixed Phase for Perovskite Solar Cells

A series of thin films made with TiO₂ nanoparticles with a varied anatase/rutile phase ratio is prepared on conducting glass substrates using a spin-coating method. The structure, morphology, and optical properties of TiO₂ nanopowders and thin films fabricated are studied using powder X-ray diffraction, scanning electron microscopy, and optical spectroscopy. The TiO₂ nanostructured films created are used as photoelectrodes for the fabrication of perovskite solar cells (PSCs). The photovoltaic characteristics of PSCs under AM1.5 light illumination (1000 W/m²) under ambient conditions are studied. It is shown that the best efficiency of solar-to-electrical energy conversion, namely, 9.3%, is obtained for the PSC with a photoelectrode based on a TiO₂ film with an anatase/rutile mixed phase ratio of 86/14%.     

Photocatalytic properties of nanocrystalline TiO<Subscript>2</Subscript> thin films doped with Tb

In this work photocatalytic properties of TiO₂ thin films doped with different amount of Tb have been described. Thin films were prepared by high energy reactive magnetron sputtering process. Comparable photocatalytic activity has been found for all doped TiO₂ thin films, while different amounts of Tb dopant (0.4 and 2.6 at. %) results in either an anatase or rutile structure. It was found that the terbium dopant incorporated into TiO₂ was also responsible for the amount of hydroxyl groups and water particles adsorbed on the thin film surfaces and thus photocatalytic activity was few times higher in comparison with results collected for undoped TiO₂ thin films.     

Novel nanocomposite membranes based on polybenzimidazole and Fe<Subscript>2</Subscript>TiO<Subscript>5</Subscript> nanoparticles for proton exchange membrane fuel cells

In this work, Fe₂TiO₅ nanoparticles were used for improving the proton conductivity, and water and acid uptake of polybenzimidazole (PBI)-based proton exchange membranes. The nanocomposite membranes have been prepared using different amounts of Fe₂TiO₅ nanoparticles and dispersed into a PBI membrane with the solution-casting method. The prepared membranes were then physico-chemically and electrochemically characterized for use as electrolytes in high-temperature PEMFCs. The PBI/Fe₂TiO₅ membranes (PFT) showed a higher acid uptake and proton conductivity compared with the pure PBI membranes. The highest acid uptake (156 %) and proton conductivity (78 mS/cm at 180 °C) were observed for the PBI nanocomposite membranes containing 4 wt% of Fe₂TiO₅ nanoparticles (PFT₄). The PFT₄ composite membrane showed 380 mW/cm² power density and 760 mA/cm² current density in 0.5 V at 180 °C at dry condition. The above results indicated that the PFT₄ nanocomposite membranes could be utilized as proton exchange membranes for high-temperature fuel cells.     

Low-temperature one-step solid-phase synthesis of carbon-encapsulated TiO<Subscript>2</Subscript> nanocrystals as anode materials for lithium-ion batteries

A simple and highly efficient method is developed for in situ one-step preparation of carbon co-encapsulated anatase and rutile TiO₂ nanocrystals (TiO₂@C) with core-shell structure for lithium-ion battery anode. The synthesis is depending on the solid-phase reaction of titanocene dichloride with ammonium persulfate in an autoclave at 200 °C for 30 min. The other three titanocene complexes including bis(cyclopentadienyl)dicarbonyl titanium, cyclopentadienyltitanium trichloride, and cyclopentadienyl(cycloheptatrienyl)titanium are used instead to comprehensively investigate the formation mechanism and to improve the microstructure of the product. The huge heat generated during the explosive reaction cleaves the cyclopentadiene ligands into small carbon fragments, which form carbon shell after oxidative dehydrogenation coating on the TiO₂ nanocrystals, resulting in the formation of core-shell structure. The TiO₂ nanocrystals prepared by titanocene dichloride have an equiaxed morphology with a small diameter of 10–55 nm and the median size is 30.3 nm. Hundreds of TiO₂ nanocrystals are encapsulated together by the worm-like carbon shell, which is amorphous and about 20–30 nm in thickness. The content of TiO₂ nanocrystals in the nanocomposite is about 31.1 wt.%. This TiO₂@C anode shows stable cyclability and retains a good reversible capacity of 400 mAh g^?1 after 100 cycles at a current density of about 100 mA g^?1, owing to the enhanced conductivity and protection of carbon shell.     

Effects of γ rays irradiation on structure and property of TiO2 thin films

TiO₂ thin films were deposited on a glass substrate by the radio frequency magnetron sputtering method, and annealed for 2 h at temperatures of 550°C. Then, ⁶⁰Co γ rays with different doses were used to irradiate the resulting TiO₂ thin films. The surface features of films before and after irradiation were observed by scanning electron microscope (SEM). Simultaneously, the crystal structure and optical properties of films before and after irradiation were studied by X-ray diffraction (XRD), UV–VIS transmission spectrum and Photoluminescence (PL) spectrum, respectively. The SEM analysis shows that the film is smooth with tiny particles on the film surface, and non-crystallization trend was clear after irradiated with γ rays. The XRD results indicated that the structure of the film at the room temperature mainly exists in the form of amorphous and mixed crystal at a sputtering power of 200 W, and non-crystallinity was more obvious after irradiation. Obvious difference can be found for the transmissibility of the irradiated and pre irradiation TiO₂ films by the UV-VIS spectra. The color becomes light yellow, and the new absorption edge also appeared at about 430 nm. PL spectra and photocatalysis experiments indicate that the photocatalysis degradation rate of the TiO₂ films on methylthionine chloride solution irradiated with the maximum dose can be increased to 90%.