首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 843 毫秒
1.
在600℃温度下,采用液相燃烧法合成了Sr2+、Eu2+和Mn2+三掺的BaMgAl10O17(BAM)蓝绿荧光粉。用XRD、SEM和荧光光谱仪分别分析和表征该荧光粉的物相、形貌和光致发光性能。结果表明,液相燃烧法合成BAM的温度明显低于传统的高温固相合成法;合成的纳米棒均匀、无团聚现象;荧光光谱仪分析表明Eu2+、Mn2+离子间存在能量传递,且Sr2+能有效提高BAM的发光强度,约为固相法制备荧光强度的1.8倍。BAM:0.1Eu2+,0.04Mn2+,0.05Sr2+色坐标为(0.146,0.250),属于蓝绿光。  相似文献   

2.
通过高温固相反应合成了新型的蓝色荧光粉Sr7Zr(PO4)6xEu2+。通过X射线粉末衍射(XRD)、紫外可见(UV-Vis)吸收光谱、荧光光谱研究了Sr7Zr(PO4)6xEu2+材料的相纯度及荧光性质。结果表明,Eu2+掺杂获得的Sr7Zr(PO4)6xEu2+荧光粉为纯相,且200~400 nm范围内的近紫外(NUV)光均能对其进行有效的激发。在315 nm的激发下,Sr7Zr(PO4)6xEu2+荧光粉发射出峰值位于415 nm左右的蓝光,且Eu2+在Sr7Zr (PO4)6基质中的最佳掺杂浓度为0.05,相应的CIE色度坐标为(0.164,0.021),比商用BaMgAl10O17∶Eu2+(BAM)蓝色荧光粉具有更高的色纯度。  相似文献   

3.
以α-Si3N4,SrCO3,Eu2O3为原料,采用碳热还原氮化法制备了Sr2Si5N8∶Eu2+荧光粉。研究了材料的结构与光谱特性,分析了影响材料发光性能的工艺因素。结果表明,石墨粉含量和助熔剂的用量对Sr2Si5N8相的形成和发光性能有重要影响。当nC/nSr=1.5,助熔剂用量为4wt%时,合成样品的主晶相为正交晶系Sr2Si5N8,在400~550 nm可见光激发下,可发射峰值波长位于609 nm荧光。激发带的位置与Eu2+离子浓度无关,为400~550 nm之间的宽带激发;但发射强度随Eu2+离子浓度的增加而增加,Eu2+离子浓度达到5mol%时发射强度达最大值,在Eu2+离子浓度为2mol%~5mol%之间,观察到发射峰的红移现象。  相似文献   

4.
采用共沉淀法及1 200 ℃后续煅烧4 h,成功制备了CaSb2O6:Bi3+,Eu3+荧光粉,并对其结构及发光性能进行了研究。所制备荧光粉颗粒为六边形类圆饼状,平均尺寸在100~600 nm之间。对CaSb2O6:Bi3+,Eu3+发光的机理分析表明,Bi3+对Eu3+的发光存在高效的敏化与能量传递。当Bi3+和Eu3+的掺杂浓度分别为0.5%和8%,Eu3+位于580 nm(5D07F0 )处的荧光发射显著增强,Bi3+,Eu3+共掺样品的荧光强度是CaSb2O6:Eu3+的10倍左右。调节Bi3+/Eu3+离子掺杂比,色坐标呈现了从蓝、白光到红光的变化,表明该荧光粉可分别作为蓝或红色荧光粉使用,甚至可实现从蓝、白光到红光的自由调控,这为白光LED荧光粉的发展提供了参考。  相似文献   

5.
本文介绍了一种新颖的方法合成碱土硅酸盐长余辉发光材料Sr3MgSi2O8:Eu2+,Dy3+。采用正硅酸乙酯(TEOS)和无机粉末在乙醇体系中,通过冰醋酸调整溶液体系pH值控制正硅酸乙酯(TEOS)的水解。前驱体形貌,晶体结构和光谱特征分别通过透射电镜(TEM),X射线粉末衍射仪(XRD)和荧光分光光度计表征。通过透射电镜照片可观察到前驱体具有核壳结构和准球形的形貌。与高温固相法相比,纳米包覆的方法具有较低的合成温度,并且具有较好的发光强度和余辉性能。  相似文献   

6.
对SrAl2O4∶Eu2+,Dy3+长余辉材料在100~500 K温度之间的发光性能进行研究。实验结果表明,材料的荧光及余辉强度在特定温度区间内呈线性变化,在热释峰所在温度范围具有较好的发光性能。其变化规律表明SrAl2O4∶Eu2+,Dy3+长余辉材料内部陷阱中电子的释放包括瞬时释放和延时释放两种类型,其中电子瞬时释放进而跃迁发光是荧光的组成部分,延时释放产生的跃迁则导致余辉发光。陷阱和电子的复合与陷阱中电子释放过程均随温度升高而增强,但温度过高时会发生热猝灭。材料荧光强度与余辉强度在特定温度区间内随温度呈线性变化关系表明其可以作为一种光纤温度传感材料。  相似文献   

7.
采用水热-均匀共沉淀法制备了纳米SrAl2O4∶Eu2+,Dy3+长余辉发光材料。通过XRD、TEM、荧光光谱、热释光谱对其结构和性能进行分析。XRD结果表明所制备的SrAl2O4∶Eu2+,Dy3+纳米发光材料为单相,属单斜晶系。TEM测试表明纳米SrAl2O4∶Eu2+,Dy3+发光材料为规则的球状粒子,粒径为50~80 nm,且分散性良好。激发和发射光谱测试表明,样品的激发光谱是峰值在356 nm的连续宽带谱,发射光谱是峰值位于512 nm的宽带谱,与SrAl2O4∶Eu2+,Dy3+粗晶材料相比,激发和发射光谱都出现了“蓝移”现象。样品的热释光峰值位于358 K,适合于产生长余辉。  相似文献   

8.
采用溶胶凝胶法制得高纯的B2O3-CaO∶Eu3+荧光粉。用XRD、IR对不同退火温度下所得样品的结构进行表征,结果发现随退火温度的变化,能形成不同结构的硼酸盐基质。通过对以不同结构硼酸盐为基质荧光粉的激发、发射谱图及荧光衰减曲线的分析,探讨了材料的发光性能和发光机理。结果表明,在不同结构硼酸盐基质中,Eu3+都处于无反演对称中心格位,以(5D0F2)电偶极跃迁为主,所以材料主要发红光;且900℃退火所得高纯相的CaB2O4基质最有利于发光、对应的荧光衰减时间最长,这都因在此荧光粉中Eu3+更易取代Ca2+,并形成相对较多的p-n结和陷阱所致。  相似文献   

9.
以B2O3为助熔剂,在1 350 ℃、还原性气氛下成功制备了SrAl2O4单相粉末样品。用同样的方法制备了系列单相Sr1-x-yAl2O4:Eu2+x,Dy3+y·nB2O3(0.005≤x≤0.07, 0.01≤y≤0.05,0.05≤n≤0.25)样品并表征了其长余辉发光特性。结果表明,最佳的Eu2+含量为0.02。辅助激活离子Dy3+在Sr0.98Al2O4:Eu2+0.02中的掺杂在一定范围内可以显著提高亮度和余辉时间,最佳Dy3+含量为0.03。研究不同B2O3含量对Sr0.95Al2O4:Eu2+0.02,Dy3+0.03发光性能的影响,结果说明最佳的B2O3含量为n=0.1,余辉肉眼可见(≥0.32 mcd·m-2)时间达4 000 min。利用正电子湮灭技术和热释光技术,研究和讨论了B2O3对Sr0.95Al2O4:Eu2+0.02,Dy3+0.03的发光和余辉性能的影响,结果表明B2O3的添加有助于Dy3+在晶格中形成深度合适、有益于余辉的空位缺陷。  相似文献   

10.
采用微波固相法制备了CaWO4xEu3+,ySm3+,zLi+红色荧光粉。测量样品的XRD图、激发谱、发射谱及发光衰减曲线,研究并分析了Eu3+、Sm3+、Li+的掺杂浓度,对样品微结构、光致发光特性、能量传递及能级寿命的影响。结果表明,Eu3+、Sm3+、Li+掺杂并未引起合成粉体改变晶相,仍为CaWO4单一四方晶系结构。Eu3+、Sm3+共掺样品中,Sm3+掺杂为3%时,Sm3+对Eu3+的能量传递最有效。Li+掺杂起到了助熔剂和敏化剂的作用,使样品发光更强。在394 nm激发下,与CaWO4:3%Eu3+样品比较,3%Eu3+、3%Sm3+共掺CaWO4及3%Eu3+、3%Sm3+、1%Li+共掺CaWO4样品的发光分别增强2倍及2.4倍。同一激发波长下,单掺Eu3+样品寿命最短,Sm3+、Eu3+共掺样品随Sm3+浓度增加,寿命先减小后增加,且掺杂了Li+的样品比不掺Li+的样品5D0能级寿命有所增加。  相似文献   

11.
Single crystals of Ca2+, Sr2+, Ba2+, and Pb2+ beta″ alumina were prepared from sodium beta″ alumina by ion exchange. The ionic conductivities of Ca2+, Sr2+, and Ba2+ beta″ alumina are comparable, about 3 × 10?2 (ohm-cm)?1 at 300°C. Surprisingly, Pb2+ beta″ alumina is much more conductive, 1.5 × 10?1 (ohm-cm)?1 at 300°C and 4.6 × 10?3 (ohm-cm)?1 at 40°C. Its conductivity approaches that of sodium beta″ alumina at temperatures below 25°C. The diffusion coefficient for Sr2+ in beta″ alumina at 600°C was estimated from radiotracer experiments. It is consistent with that expected from conductivity measurements.  相似文献   

12.
13.
14.
15.
16.
The solubility polytherms in the systems for which the cryoscopic data are lacking were measured. The structural models of the electrolyte solutions were discussed on the basis of the solubility polytherms.__________Translated from Zhurnal Prikladnoi Khimii, Vol. 78, No. 3, 2005, pp. 413–417.Original Russian Text Copyright © 2005 by Pestova, Myund, Khripun, Prigaro.  相似文献   

17.
The B3LYP/6-311++G (d,p) density functional approach was used to study the gas-phase metal affinities of Guanosine (ribonucleoside) for the Li+, Na+, K+, Mg2+, Ca2+, Zn2+, and Cu+ cations. In this study we determine coordination geometries, binding strength, absolute metal ion affinities, and free energies for the most stable products. We have also compared the results for Guanosine, with our previously reported results for 2′-Deoxyguanosine. Based on the results, it is obvious that MIA is strongly dependent on the charge-to-size ratio of the cation. Guanosine interacts more strongly with Zn2+ than do with Mg2+, Ca2+, and Cu+ and therefore stronger interactions lead to higher MIA. In both free molecules and their complexes, the Syn orientation of the base is stabilized by an intramolecular O5′–H···N3 hydrogen bond and the anti orientation of the base is stabilized by an intramolecular C–H···O hydrogen bond formed between the (C8-H8) and the O5′ atom of the sugar moiety. It is also interesting to mention that linear correlation between calculated MIA values and the atomic numbers (Z) of the metal ions of Li+, Na+, and K+ were found. Furthermore, the influences of metal cationization on the strength of the N-glycosidic bond, torsion angles, angle of pseudorotation (P), and intramolecular C–H···O and O–H···O hydrogen bonds have been studied. Natural bond orbital (NBO) analysis was performed to calculate the charge transfer and natural population analysis of the complexes. Quantum theory of atoms in molecules (QTAIM) was also applied to determine the nature of interactions.  相似文献   

18.
Zusammenfassung Es wurde eine neue metallochrome Substanz, das 2-Bis(carboxymethyl)-aminomethyl-4(p-sulfophenyl)azo-naphthol synthetisiert, Methylnaphtholorange genannt. Ihre konsekutiven Dissoziationskonstanten wurden bestimmt, optimale Bedingungen ihrer Reaktion mit Ti4+, Sm3+ und UO 2 2+ aufgefunden, die Zusammensetzung der entstehenden Metallkomplexe festgestellt und die Bildungs- als auch Stabilitätskonstanten berechnet.
Summary A new metallochromic compound, 2-Bis(carboxymethyl)-aminomethyl-4(p-sulphophenyl)-azonaphthol, (named methylnaphthol orange) has been synthezised. Its consecutive dissociation constants have been determined, optimal conditions of its reactions with Ti4+, Sm3+ and UO 2 2+ worked out, the composition of the metal complexes identified and the constants of formation and stability have been computed.


Für technische Hilfe hei dieser Arbeit bin ich Herrn K. Haas dankbar.  相似文献   

19.
20.
Synthesis of fourteen new complexes of meso-tetrakis(4-alkoxyphenyl) porphyrins with Co2+, Cu2+, Zn2+, Pb2+ were presented in this paper.Meso-tetrakis (4-alkoxyphenyl) porphyrins were prepared by condensation of 4-alkoxybenzaldehydes with pyrrole, then treated with corresponding metallic acetate to produce mentioned complexes, IR, UV, 1H NMR, MS and elementary analysis were explored to confirm the structures of all theses new complexes.Characteristic spectrometric data of IR, UV, 1H NMR related to these complexes have been systematically summarized.Ten of the fourteen complexes were found to exhibit liquid crystal properties.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号