ET-AAS in the Analysis of high-purity mercury

ET-AAS is investigated for the analysis of high purity mercury. Two possibilities are proposed: ET-AAS determination of trace analytes in the presence of high mercury concentrations or after matrix separation by reduction. The ET-AAS analysis of high-purity mercury under optimal instrumental parameters permits fast and reproducible determination of 0.03 gg^–1 Al, Cd and Mn; 0.05 gg^–1 Cu, Co, Cr, Fe, Ni and Pb and 0.2 gg^–1 V. Preliminary mercury matrix reductive separation with ascorbic acid allows determination of 0.005 gg^–1 Cd, 0.02 gg^–1 Cu, Cr and Mn, 0.03 g g^–1 Co, Ni and Pb, 0.05 g g^–1 Al and Fe and 0.1 gg^–1 V, but the reproducibility is lower. The main advantage of the second procedure is that it avoids laboratory and instrument pollution with toxic mercury.     

Spectrophotometric determination of mercury with 5,10,15,20-tetrakis(3-chloro-4-sulfophenyl)porphine by flow injection analysis

5,10,15,20-tetrakis(3-chloro-4-sulfophenyl)porphine (m-Cl-TPPS₄) was synthesized and used for the Spectrophotometric determination of mercury by flow injection analysis. A pseudo-first-order reaction kinetic mechanism was proposed with a rate constant of 0.8 min^–1 for Hg(II) withm-Cl-TPPS₄ in the presence of 8-hydroxyquinoline in a medium of 1.0M acetic acid and sodium acetate buffer solution (pH 6.22). In the optimum conditions of reaction temperature (85 ° C), stopped-flow time (60 s) and sampling volume (100 l), the method's relative standard deviation was 0.82% (n = 12) at 5.0 g ml^–1 mercury, with a linear range of 0–12.0 g ml^–1 and an analytical frequency of 60h^–1. The detection limit (3) was 0.025 g ml^–1. Interference studies showed that most metal ions co-existing with Hg²⁺ could be tolerated at 100-fold excess levels, but Zn²⁺, Cu²⁺ and Mn²⁺ needed to be masked. The method has been applied to the analysis of water samples with satisfactory results.     

Simultaneous determination of neodymium and erbium in rare earth mixture with 5,7-dibromo-8-hydroxyquinoline and TX-100 by third-derivative spectrophotometry

The absorption spectra of 4f electron transitions of the complexes of neodymium and erbium with 5,7-dibromo-8-hydroxyquinoline in the presence of octylphenol poly(ethyleneglycol)ether have been studied by normal and third-derivative spectrophotometry. The proposed method is free of interference of other rare earths. The calibration graphs were linear up to 18 g/ml of neodymium and 21 g/ml of erbium (in the final solution). The derivative molar absorptivities are 395 l.mol^–1.cm^–1 for neodymium and 3421.mol^–1.cm^–1 for erbium. The corresponding values of Sandell's sensitivity were 0.36 and 0.49 g.cm^–1, respectively. The relative standard deviations evaluated from ten independent determinations of 2.5 g/ml of neodymium and erbium are 1.5 and 3.8% for neodymium and 1.8 and 4.1% for erbium in absence and presence of 70 g of lanthanum, respectively. The detection limits (signal to noise ratio=2) are 0.23 g/ml for neodymium and 0.30 g/ml for erbium. The method has been used for the determination of neodymium and erbium in mixed rare earths with satisfactory results.     

A toxic reagent-free method for normal-phase matrix solid-phase dispersion extraction and reversed-phase liquid chromatographic determination of aldrin,dieldrin, and DDTs in animal fats

A method for the determination of aldrin, dieldrin, DDT, DDE, and DDD contamination in animal fats (beef tallow, lard, and chicken fat) without using toxic reagents is developed, that uses high-performance liquid chromatography after the sample has been prepared by matrix solid-phase dispersion (MSPD) with acidic alumina oxide. A reversed-phase C₁-silica column with a mobile phase of 50% (v/v) ethanol solution (in water) and a photo-diode array detector were used for the determination. Average recoveries of the target compounds (0.2–5.0 g g^–1) ranged from 84–98%, with coefficients of variation of <5%. The limits of quantitation were 0.16 g g^–1 for AD, 0.10 g g^–1 for DD, 0.06 g g^–1 for DDT, 0.07 g g^–1 for DDE, and 0.05 g g^–1 for DDD. No toxic reagents were used at all.     

Assessment of the essential element and heavy metal content of edible fish muscle

The aim of this work was to determine the concentrations of some essential and toxic elements in the muscle of ten species of commercial fish consumed in Portugal. We combined two different techniques for determination of the elements—energy-dispersive X-ray fluorescence (EDXRF) was used to quantify K, Ca, Fe, Zn, Se, Rb, and Sr and flame atomic-absorption spectrometry for analysis of Cr, Ni, Cu, Cd, Hg, and Pb. The latter technique was used because of its higher sensitivity, because these elements were not detected by EDXRF. The results obtained show a similar pattern for the trace elements. K and Ca are present at the highest concentrations in all the samples studied, from 0.6–1.3% and from 0.04–0.08%, respectively, followed by Zn, Fe, Sr, Se, and Rb. Sr is present at higher concentrations than Rb in all the species studied except meagre. Concentrations of the elements in octopus do not follow this pattern—Fe is present at a higher concentration than Zn. Low concentrations of Cr (0.66–1.5 g g^–1), Ni (0.11–0.24 g g^–1), Cd (0.01–0.08 g g^–1), Hg (0.49–2.74 g g^–1), and Pb (0.02–0.06 g g^–1) were observed in all the samples analysed. The concentration of Hg was highest in Helicolenus dactylopterus—5.4 g g^–1 in one sample.     

Thorium in man and environment uptake and clearance

The intake and tissue distribution of thorium (^{2 3 2}Th) was studied in an urban (Bombay) population in India. From the analysis of 16 whole diet samples, the average daily intake through food was found to be 2 g (range 0.8–4.3 g·d^–1). The estimated intake through drinking water and inhalation comes out to be 0.03 and 0.02 g per day. From the analysis of human autopsy tissue samples it is observed that the concentration ranges in lungs and bone are 1.5–16 g/kg and 0.2–9.0 g/kg fresh weight respectively. The average urinary concentration is 12 ng/1 (range 7–22 ng/l for 10 samples). Among the different body tissues, pulmonary lymph nodes were found to contain the highest concentration (geometric mean 53.4 g/kg, range 31.4–85.5 g/kg for 6 samples). Analysis of the samples was done by the neutron activation technique. 311.8 keV gamma photons of^{2 3 3}Pa which is the activation product of^{2 3 2}Th, were counted after chemical separation. A 54 cm³ intrinsic Ge detector coupled to 1024-channel analyser was used. Using the average lung content and the daily average intake values of thorium through inhalation, the clearance half-time from lung was estimated.     

Multi-residue procedure for the analysis of pesticides in groundwater: Application to samples from the comunidad Valenciana,Spain

Summary A simple multi-residue procedure has been developed and applied to the analysis of pesticides in groundwater samples from the Comunidad Valenciana, a predominantly agricultural area on the Mediterranean coast of Spain. The procedure includes a liquid-liquid extraction, after addition of NaCl on the samples, and a subsequent analysis by capillary gas chromatography using a dual detection system with electron capture and nitrogen-phosphorous detectors. This allows the determination of more than 30 compounds (organophosphorous, organochlorine and pyrethroid pesticides) at the low ppb (g l^–1) levels. Detection limits obtained varied between 0.01 g l^–1 (lindane, fonofos) and 0.5 g l^–1 (cypermethrin). An additional injection of the sample extracts into a gas chromatograph equipped with a column of different polarity and electron capture detector is used for the confirmation of chromatographic peaks. The recommended procedure has been applied to 66 ground water samples. Pesticides, including organophosphorus and organochlorine compounds were detected in 31 of them, in levels ranging from 0.02 to 0.7 g l^–1.     

Determination of traces of heavy metals in positively charged inorganic colloids in fresh waters

Summary Determination of Traces of Heavy Metals in Positively Charged Inorganic Colloids in Fresh Waters After removal of suspended particulate matter by centrifugation followed by filtration through 0.4-m membrane filters, humic substances and other negatively charged species are sorbed on a small column of macroreticular weak-base anion exchanger DEAE-Sephadex A-25 at fast flow rates. Positively charged inorganic colloids pass through the column and are collected on a 0.015-m membrane filter, which is then ultrasonically treated with 1M nitric acid for the determination of copper, lead and cadmium by differential pulse anodic stripping voltammetry with a static mercury drop electrode. Up to O.2g 1^–1 of the heavy metals are found in positively charged inorganic colloids in river, pond and tap waters.     

Method comparison study on soot-selective techniques

In a long-term field study at two locations with different air pollution levels several soot-selective measurement techniques were compared with a thermochemical method which measures non-extractable carbon (NEC) detecting the evolved CO₂ by means of coulometric titration. The attenuation measurement technique (aethalometer) and the aerosol photoemission method showed good correlations to NEC for concentrations ranging from 1.6g/m³ to 40.8g/m³. The specific mass absorption coefficient of black carbon with respect to NEC varied between 8.4m²/g and 13.7m²/g with respect to the measurement sites, but the value was found to remain constant at each site independent of seasonal or meteorological variations. The ratio of photoelectric signal to NEC varied between 16 fA·(g/m³)^–1 and 33 fA·(g/m³)^–1 depending on the age of the aerosol. The diurnal variations of that ratio showed strong similarities to the traffic patterns. Additionally a slight temperature dependence of this ratio was found for the aged aerosol with a proportionality factor of – 0.35 fA·(K·g/m³)^–1. With the reflectance measurement technique (smoke shade method) reliable NEC determination was not possible for NEC concentrations 5 g/m³.     

Stripping voltammetric determination of trace amounts of mercury using a carbon paste electrode modified with 2-mercapto-4(3H)-quinazolinone

A carbon paste electrode modified with 2-mercapto-4(3H)-quinazolinone was used for the voltammetric determination of mercury(II). Mercury was preconcentrated onto the surface of the modified electrode only by the complexing effect of the modifier without application of potential (i.e. in open-circuit conditions). After exchange of the medium, the accumulated amount of mercury(II) was determined by differential pulse anodic stripping voltammetry. The response depended on the concentration of mercury in the bulk solution, preconcentration time, and other parameters. The detection limit was 0.1 g 1^–1 Hg(II) for a preconcentration time of 15 min. Preconcentration for suitable times yielded a linear calibration graph from 0.5 to 6000 g 1^–1 Hg(II). For multiple determinations (5 runs), the relative standard deviation was 5% for a concentration of 100 g 1^–1 Hg(II). The proposed procedure was used to determine trace mercury in plant and sewage sludge samples with good results.On leave from Hainan University, Hainan Peoples Republic of China     

Characterization of airborne particulates by laser microprobe mass analysis

Summary Laser microprobe mass analysis (LAMMA) was applied to characterize aerosol particles collected and separated from 16m to 0.06m by a low pressure cascade impactor. Positive ion LAMMA spectra showed characteristic molecular peaks such as PbCl⁺, a series of Si₂O⁺–Si₂O₄ ⁺ and NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, and TiO⁺ in 0.06–0.12m, 0.5–1m and 4–8m fraction, respectively. In the negative ion LAMMA spectra, it was observed that the fragment peaks of sulfate ions were deficient above 2m and those of nitrate ions were deficient under 2m. LAMMA allows remarkable insights into the chemical nature of aerosol particles.

---

Charakterisierung luftgetragener Teilchen durch Laser-Microprobe-Massenspektrometrie

Zusammenfassung Laser-Microprobe-Spektrometrie (LAMMS) wurde zur Analyse atmosphärischen Aerosols herangezogen, welches im Korngrößenbereich zwischen 16m und 0.06m mit einem Niederdruckkaskadenimpaktor fraktioniert gesammelt wurde. Positive LAMMS-Spektren zeigten charakteristische molekulare Peaks, wie etwa PbCl⁺, eine Serie von Si₂O⁺–Si₂O₄ ⁺ und NaAl₂Si₂O₂ ⁺–NaAl₂Si₂O₅ ⁺, sowie TiO⁺ in der 0,06–0,12-m,- 0,5–1–m- bzw. 4–8-m-Fraktion. In den negativen LAMMS-Spektren konnten über 2m keine Fragmentpeaks für Sulfationen, unter 2m. keine für Nitrationen beobachtet werden. LAMMS ermöglicht eine bemerkenswerte Einsicht in die chemische Natur von Aerosolteilchen.

     

Tail-end purification of americium from plutonium loading effluents using a mixture of octyl (phenyl)-N,N-diisobutylcarbamoylmethylphosphine oxide and tri-N-butyl phosphate

The tail-end purification of Am from Pu loading effluents in 7.5M HNO₃ containing 160 mg l^–1 Am and 1.2 mg l^–1 Pu has been carried out. With 0.2M CMPO+1.2M TBP in dodecane as the extractant and stripping by 0.04M HNO₃+0.05M NaNO₂, the Pu level is brought down to 31.2 g l^–1. When the acidity was reduced to 4.2M HNO₃, one contact with 20% TLA/dodecane and subsequent extraction by a mixture of CMPO and TBP and stripping with 0.04M HNO₃+0.05M NaNO₂ gave Am samples without any detectable amounts of Pu. The recovery of Am was 90% by the first procedure and 98% by the second one.     

Mercury determination by CV-AAS in wastewater and sewage sludge from a stabilization pond system

The mercury concentrations in wastewater and sewage sludge of a stabilization pond system have been evaluated. The system is built by three parallel facultative ponds followed by two systems of three maturation ponds in series. The samples of wastewater and sludge were digested using nitric acid and placed into a Parr-type bomb for 4 h at 110° C. Mercury was measured by Cold Vapour Atomic Absorption Spectrometry (CV-AAS) at 253.7 nm with sodium tetrahydroborate as reductant. The methodologies were checked with an USEPA quality control sample, a standard reference material from NIST and with another method of mineralization (cold mineralization) showing good results. Concentrations of mercury in wastewater between 1.47 ± 0.75 gl^–1 have been found at the entrance of the system and 0.74 ± 0.0 gl^–1 at the exit, while in sludge the results were between 0.29 ± 0.12 gkg^–1 in the facultative pond and 0.04 ± 0.02 gkg^–1 in the second maturation pond (exit).     

Thiolactame als Reagenzien in der quantitativen Analyse. IX

Zusammenfassung Thiocaprolactam (T) eignet sich zur Goldbestimmung im Konzentrationsbereich 10 bis 130 g Au/ml mit einem Fehler von ±0,5g. Thiocaprolactam bildet mit [AuCl₄]^– eine Verbindung im molaren Verhältnis TAuCl=112, mit [AuJ₄]^– im molaren Verhältnis TAuJ=213. Dagegen bilden sich im System T:Au:Br zwei verschiedene Verbindungen: Ein Bromidkomplex mit höherem Goldgehalt TAu=12, der mit Chloroform extrahierbar ist, und eine sich als Niederschlag ausscheidende Verbindung mit dem Verhältnis TAuBr=112.

---

Thiolactams as reagents in quantitative analysis. IX

Summary Thiocaprolactam (T) is suitable for the determination of gold in the concentration range 10–130g Au/ml with an error of ±0.5g. Thiocaprolactam yields with [AuCl₄]^– a compound in the molar ratio TAuCl=112, with [Aul₄]^– in the molar ratio TAuI=213. On the other hand various compounds result in the system TAu Br. The molar ratio in the case of the bromide complex has a higher gold content, namely TAu=12; this product is extractable with chloroform and a compound that comes down as a precipitate shows the ratioT Au Br=112.

---

---

Herrn Dr.K. Czerepko möchte ich hiermit meinen Dank für die Diskussion der Ergebnisse aussprechen.     

Application of l-cysteine-capped nano-ZnS as a fluorescence probe for the determination of proteins

Nanometer-sized l-cysteine-capped ZnS particles have been synthesized and used as a fluorescence probe to investigate the effect of proteins on fluorescent intensity. With =190 nm, maximum and constant synchronous fluorescence enhancement was produced at 267 nm and pH 5.12 in the presence of proteins. A highly sensitive synchronous fluorescence method for the rapid determination of proteins has been developed. Under optimum conditions, calibration graphs are linear over the range 0.03–8.0 g mL^–1 for bovine serum albumin (BSA), 0.01–6.0 g mL^–1 for human serum albumin (HSA), 0.05–8.0 g mL^–1 for -globulin (-G), and 0.04–4.0 g mL^–1 for ovalbumin, respectively. The relative standard deviations of seven replicate measurements were 1.75% for 1.0 g mL^–1 BSA, 1.90% for 1.0 g mL^–1 HSA, 1.65% for 1.0 g mL^–1 -G, and 2.32% for 1.0 g mL^–1 ovalbumin.     

Extraction-spectrophotometric determination of nickel as Ni-(PAR)2-(CTAB)2 complex in polymetallic sea-bed nodules and steels

A red, water-soluble complex of nickel with PAR can be extracted into chloroform with CTAB at pH 7.0. The system obeys Beer's law upto 0.5 g/ml with a molar absorptivity of 45 200 L·mol^–1·cm^–1 at 540 nm. Job's method of continuous variations revealed that the composition of the extracting species is 1:2:2 for nickel:PAR:CTAB. Based on this extraction, a highly sensitive and selective spectrophotometric method for the determination of nickel in polymetallic sea-bed nodules and in steels, after prior separation of iron and manganese, was developed. The standard deviation was 0.04–0.127 g for 5–25 g of nickel.     

Protonation of Os3(μ-H)(CO)9(μ3-σ,η2-C≡C-R) clusters (R=CMe2OH,C(Me)=CH2)

Protonation of triosmium clusters Os₃(-H)(CO)₉(₃-,²-CC-R) (R=CMe₂OH, C(Me)=CH₂) affords a cationic complex containing a six-electron propargyl ligand which has been detected for the first time.Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1144–1145, June, 1993.     

Determination of heavy metals in sea water and in marine organisms by flameless atomic absorption spectrophotometry

Summary In natural waters, heavy metals such as Cd may be present in bound form. It is, therefore, important to consider chemical speciation, especially at low concentrations of the metal where a significant part can be bound by other trace constituents so tightly that it escapes several forms of its determination. It has been demonstrated that even the very strong complexant APDC is unable to leach out all of the heavy metal present in several coastal water samples from the German Bight.This paper describes a new micro method for the determination of total Cd in natural waters. First a small sample is dried in a polypropylene vial. Then the salt residue is heated to 90° C with a mixture of sulphuric and nitric acid for digestion of organic trace constituents (and oxidation of sulphides if present). After dilution subsamples are neutralized using an excess of NaHCO₃ buffer solution. Extraction results are then independent from the possible slight variations of pH. The extractant, a solution of APDC in CCl₄ is stable for weeks, and even the extract is stable for at least 16h. Precision is in the range of 7% at a concentration of 0.066 g Cd l^–1; the detection limit is below 0.002 g l^–1 and can be lowered, if necessary, by enlargement of the original sample. According to the sensitivity of the method the typical blank of 0.022 g Cd l^–1 is high, but it is rather constant (mean variation from the mean: 0.0024 g l^–1).Teil XI: Fresenius Z. Anal. Chem. 299, 206–207 (1979)     

Determination of medecamycin by adsorptive stripping voltammetry with an activated electrode

The adsorptive and electrochemical behaviors of medecamycin were investigated on a glassy carbon electrode (GCE) pretreated by anodic oxidation at +1.8 V for 5 min in 0.025 mol l^–1 NH₃-NH₄Cl (pH 8.6) solution. An adsorptive stripping voltammetric method for the determination of medecamycin at the pretreated glassy carbon electrode has been developed. Medecamycin was accumulated in NH₃-NH₄Cl buffer (pH 9.0) at a potential of –0.7 V (vs. saturated calomel electrode (SCE)) for a certain time, and then determined by second-order differential anodic stripping voltammetry. The second-order differential anodic stripping peak current at +0.72 V was proportional to the concentration of medecamycin in the range 2.0 g ml^–1 to 50.0 g ml^–1. The detection limit (three times the signal-to-noise) was 1.0 g ml^–1 and the relative standard deviation of the results was 3.28% for eight successive determinations of 10.0 g ml^–1 medecamycin. This method has been applied to the direct determination of medecamycin in commercial tablets and spiked urine samples with satisfactory results.     

Platinum concentration in silicone breast implant material and capsular tissue by ICP-MS

Inductively coupled plasma-mass spectrometry (ICP-MS) was used to determine the concentration of platinum (Pt) in silicone breast implant gel (range, 0.26–48.90 g g^–1 Pt; n=15), elastomer (range, 3.05–28.78 g g^–1 Pt; n=7), double lumen (range, 5.79–125.27 g g^–1 Pt; n=7), foam (range, 5.79–8.36 g g^–1 Pt; n=2), and capsular tissue (range, 0.003–0.272 g g^–1 Pt; n=15). The results show that very high levels of Pt are present in the encasing elastomer, double lumen, and foam envelope materials. Silicone breast implants can be a source of significant Pt exposure for individuals with these implants.