Impedance studies on the 5-V cathode material,LiCoPO<Subscript>4</Subscript>

Olivine-structured LiCoPO₄ is synthesized by a Pechini-type polymer precursor method. The structure and the morphology of the compounds are studied by the Rietveld-refined X-ray diffraction, scanning electron microscopy, Brunauer, Emmett, and Teller surface area technique, infrared spectroscopy, and Raman spectroscopy techniques, respectively. The ionic conductivity (σ ionic), dielectric, and electric modulus properties of LiCoPO₄ are investigated on sintered pellets by impedance spectroscopy in the temperature range, 27–50 °C. The σ (ionic) values at 27 and 50 °C are 8.8 × 10⁻⁸ and 49 × 10⁻⁸ S cm⁻¹, respectively with an energy of activation (E _a) = 0.43 eV. The electric modulus studies suggest the presence of non-Debye type of relaxation. Preliminary charge–discharge cycling data are presented.     

Synthesis, characterization, and electrical conductivity of new Aurivillius-type oxide-ion conductor

A new oxide-ion conductor of Aurivillius family with a general formula Bi₂Al _x V_{1 − x} O_{5.5 − x − δ}; 0 ≤ x ≤ 0.20 (BIALVOX) was synthesized by the sol-gel citrate route. Powder X-ray diffraction and simultaneous thermogravimetric and differential thermal analyses confirmed that the calcination of BIALVOX xerogels is fully completed at around 500°C after three hours of thermal treatment. It has been found that the β-orthorhombic phase is stabilized with compositions x ≤ 0.07, whereas the stabilization of the γ′-phase takes place for x ≥ 0.10. AC impedance spectroscopic investigation suggested that the charge accumulation at grain boundaries is thermally activated process. However, the maximum electrical conductivity (7.73 × 10⁻⁵ S cm⁻¹) noticed for BIALVOX.13 at 300°C was attributed to the maximum vacancy concentration in the equatorial planes, responsible for the ion diffusion through the structure. This has been further evidenced by the temperature dependence of dielectric permittivity.     

Preparation of a novel polymer gel electrolyte based on N-methyl-quinoline iodide and its application in quasi-solid-state dye-sensitized solar cell

Using poly(acrylonitrile-co-styrene) as polymer host, 1,2-propanediol carbonate, dimethyl carbonate and ethylene carbonate as mixture solvent, N-methyl-quinoline iodide and iodine as the source of I⁻/I₃ ⁻, a novel polymer gel electrolyte with ionic conductivity of 5.12 × 10⁻³ S· cm⁻¹ at 25°C was prepared by sol-gel and hydrothermal methods. Based on the polymer gel electrolyte, a quasi-solid-state dye-sensitized solar cell was fabricated. The solar cell possess better long-term stability and light-to-electrical energy conversion efficiency of 4.04% under irradiation of 100 mW· cm⁻². The influences of polymer host, solvent, N-methyl-quinoline iodide and temperature on ionic conductivity of the polymer gel electrolyte and the performance of the dye-sensitized solar cell was discussed.     

Electrical and electrochemical studies on magnesium ion-based polymer gel electrolytes

The development of polymer gel electrolyte system with high ionic conductivity is the main objective of polymer research. Electrochemical devices based on lithium ion-conducting polymer electrolyte are not safe due to the explosive nature of lithium. An attempt has been made to synthesize magnesium ion-conducting polymeric gel electrolytes, poly (vinylidene fluoride-co-hexafluoropropylene)–propylene carbonate–magnesium perchlorate, PVdF(HFP)-PC–Mg(ClO₄)₂ using standard solution-cast techniques. The maximum room temperature ionic conductivity of the synthesized electrolyte system has been observed to be 5.0 × 10⁻³ S cm⁻¹, which is quite acceptable from a device fabrication point of view. The temperature-dependent conductivity and the dielectric behavior were also analyzed. The pattern of the temperature-dependent conductivity shows the Arrhenius behavior. The dielectric constant ε _r and dielectric loss ε _i increases with temperature in the low-frequency region but almost negligible in the high-frequency region. This behavior can be explained on the basis of electrode polarization effects. The real part M _r and imaginary part M _i versus frequency indicate that the systems are predominantly ionic conductors. Further, the synthesized electrolyte materials have been checked for its suitability in energy storage devices namely redox supercapacitor with conducting polymer polypyrrole as electrode materials, and finally, it was observed that it shows good capacitive behavior in low-frequency region. Preliminary studies show that the overall capacitance of 22 mF cm⁻² which is equivalent to a single electrode specific capacitance of 117 F gm⁻¹ was observed for the above said supercapacitors.     

Conductivity of potassium-cationic solid electrolytes in the K0.85Pb0.075(Fe1 ? xAlx)O2 system

New potassium-conducting solid electrolytes in the mixed ferrite-aluminate system K_0.85Pb_0.075(Fe_{1 − x} Al _x )O₂ are synthesized and studied. The electrolytes exhibit high ionic conductivity in the studied temperature range of 350 to 750°C (approximately 10⁻² S/cm at 400°C and approximately 10⁻¹ S/cm at 700°C). An increase in the conductivity with increasing concentration of iron in the specimens is a general tendency. However, in a wide range of compositions (from x = 0.2 to x = 0.9), the conductivity only slightly depends on x. Possible reasons for the effect of Fe/Al ratio in the structure of solid electrolytes on their transport properties are discussed.     

Preparation and characterization of lithium ion conducting ionic liquid-based biodegradable corn starch polymer electrolytes

Thin films of biodegradable corn starch-based biopolymer electrolytes were prepared by solution casting technique. Lithium hexafluorophosphate (LiPF₆) and 1-butyl-3-methylimidazolium trifluoromethanesulfonate (BmImTf) were employed as lithium salt and ionic liquid, respectively. With reference to the temperature dependence study, Arrhenius relationship was observed. The highest ionic conductivity of (6.00 ± 0.01) × 10⁻⁴ S cm⁻¹ was obtained at 80 °C. Based on x-ray diffraction (XRD) result, the peaks became broader with doping of ionic liquid revealing the higher amorphous region of the biopolymer electrolytes. Ionic liquid-based biopolymer electrolytes exhibited lower glass transition temperature (T _g).     

A polymer electrolyte containing ionic liquid for possible applications in photoelectrochemical solar cells

Various iodide ion conducting polymer electrolytes have been studied as candidate materials for fabricating photoelectrochemical (PEC) solar cells and energy storage devices. In this study, enhanced ionic conductivity values were obtained for the ionic liquid tetrahexylammonium iodide containing polyethylene oxide (PEO)-based plasticized electrolytes. The analysis of thermal properties revealed the existence of two phases in the electrolyte, and the conductivity measurements showed a marked conductivity enhancement during the melting of the plasticizer-rich phase of the electrolyte. Annealed electrolyte samples showed better conductivity than nonannealed samples, revealing the existence of hysteresis. The optimum conductivity was shown for the electrolytes with PEO:salt = 100:15 mass ratio, and this sample exhibited the minimum glass transition temperature of 72.2 °C. For this optimum PEO to salt ratio, the conductivity of nonannealed electrolyte was 4.4 × 10⁻⁴ S cm⁻¹ and that of the annealed sample was 4.6 × 10⁻⁴ S cm⁻¹ at 30 °C. An all solid PEC solar cell was fabricated using this annealed electrolyte. The short circuit current density (I _SC), the open circuit voltage (V _OC), and the power conversion efficiency of the cell are 0.63 mA cm⁻², 0.76 V, and 0.47% under the irradiation of 600 W m⁻² light.     

Rubidium-conducting solid electrolytes in Rb2 ? 2xFe2 ? xVxO4 system

New solid rubidium-conducting electrolytes based on rubidium monoferrite in the system of Rb_{2 − 2x} Fe_2−x V _x O₄ are synthesized and studied. It is found that introduction of V⁵⁺ ions causes a drastic decrease in the electronic conductivity component prevalent in pure RbFeO₂ with a simultaneous increase in the ionic conductivity. The latter becomes predominant at an increase in the concentration of vanadium. The optimum compositions of the studied electrolytes feature a very high cationic rubidium conductivity (∼1.8 × 10⁻² S cm⁻¹ at 200°C, more than 10⁻¹ S cm⁻¹ at 700°C). The results are compared with the data obtained earlier for similar systems based on RbGaO₂ and RbAlO₂.     

Potassium-ionic conduction in the gallate-ferrite solid electrolytes

New potassium-conducting solid electrolytes in the mixed gallate-ferrite systems (1 − x)Ga₂O₃ · xFe₂O₃ · 0.25TiO₂ · K₂O and 1.5[(1 − x)Ga₂O₃ · xFe₂O₃] · TiO₂ · 2K₂O are synthesized and studied. The electrolytes exhibit high ionic conductivity in the test temperature range of 300 to 750°C (above 10⁻² S/cm at 300°C and above 10⁻¹ S/cm at 700°C). An increase in the conductivity with increasing concentration of iron in the specimens is a general tendency. Possible reasons for the effect of Ga/Fe ratio in the structure of solid electrolytes on their transport properties are discussed.     

Sulfurization of polymers

Polyethylene is exhaustively sulfurized by elemental sulfur at 160–365 °C to release hydrogen sulfide and form black lustrous powders (sulfur content ≈80%) that possess electric conductivity (10⁻⁶–10⁻⁸ S cm⁻¹ when doped with I₂). Elemental analysis data, IR spectra, X-ray patterns, DSC-TGA. derivatographic data, electric conductivity, and mass spectrometric characteristics of the polymers synthesized suggest the presence of fused polythienothiophene and polynaphthothienothiophene blocks in the polymers. For Part 1, see Ref. 1 Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 5, pp. 865–871, May, 2000.     

Novel composite polymer electrolytes based on poly(ether-urethane) network polymer and fumed silicas

Novel composite solid polymer electrolytes (CSPEs) and composite gel polymer electrolytes (CGPEs) have been prepared. CSPE consists of poly(ether-urethane) network polymer (PUN), fumed silicas and LiClO₄. The ionic conductivity of CSPEs can be enhanced nearly 20 times in comparison with the plain system without the addition of fumed silicas and can be above 1×10⁻⁵ S/cm at room temperature. The effects of both kinds of fumed silicas, viz. uSiO₂ with hydrophilic groups at the surface and mSiO₂ with hydrophobic groups at the surface on ionic conductivity were investigated. CGPE comprising of the CSPE and LiClO₄–PC solution with good mechanical strength exhibits ionic conductivity in the order of 10⁻³ S/cm at room temperature and above 3×10⁻⁴ S/cm at low temperature −40 °C.     

Enhanced electrochemical properties of polyethylene oxide-based composite solid polymer electrolytes with porous inorganic–organic hybrid polyphosphazene nanotubes as fillers

Solid composite polymer electrolytes consisting of polyethylene oxide (PEO), LiClO₄, and porous inorganic–organic hybrid poly (cyclotriphosphazene-co-4, 4′-sulfonyldiphenol) (PZS) nanotubes were prepared using the solvent casting method. Differential scanning calorimetry and scanning electron microscopy were used to determine the characteristics of the composite polymer electrolytes. The ionic conductivity, lithium ion transference number, and electrochemical stability window can be enhanced after the addition of PZS nanotubes. The electrochemical impedance showed that the conductivity was improved significantly. Maximum ionic conductivity values of 1.5 × 10⁻⁵ S cm⁻¹ at ambient temperature and 7.8 × 10⁻⁴ S cm⁻¹ at 80 °C were obtained with 10 wt.% content of PZS nanotubes, and the lithium ion transference number was 0.35. The good electrochemical properties of the solid-state composite polymer electrolytes suggested that the porous inorganic–organic hybrid polyphosphazene nanotubes had a promising use as fillers in SPEs and the PEO₁₀–LiClO₄–PZS nanotube solid composite polymer electrolyte might be used as a candidate material for lithium polymer batteries.     

Rubidium-cationic conductance in the systems Rb2 ? 2xAl2 ? xAxO4 (A = P, V)

RbAlO₂-based solid solutions are synthesized in the systems Rb_{2 − x} Al_{2 − x} A _x O₄ (A = P, V). Temperature and concentration dependences of their conductance are studied; the rubidium-cationic character of the conductance is corroborated. The high ionic conductivity of the synthesized phases (∼5 × 10⁻³ S cm⁻¹ at 300°C, ∼2 × 10⁻² S cm⁻¹ at 700°C) is caused by (a) formation of rubidium vacancies as a result of the replacing of Al³⁺ ions by fivefold-charged cations of phosphorus or vanadium and (b) disordered crystal structure of γ-KAlO₂ type. The obtained data are compared with the results of the studying of similar systems. Original Russian Text ? G.Sh. Shekhtman, E.I. Volegova, E.I. Burmakin, 2009, published in Elektrokhimiya, 2009, Vol. 45, No. 4, pp. 495–499.     

Improved properties of polymer electrolyte by ionic liquid PP1.3TFSI for secondary lithium ion battery

A new kind of polymer electrolyte is prepared from N-methyl-N-propylpiperidinium bis (trifluoromethanesulfonyl) imide (PP1.3TFSI), polyethylene oxide (PEO), and lithium bis (trifluoromethanesulfonyl) imide (LiTFSI). IR and X-ray diffraction results demonstrate that the addition of ionic liquid decreases the crystallization of PEO. Thermal and electrochemical properties have been tested for the solid polymer electrolytes, the addition of the room temperature molten salt PP1.3TFSI to the conventional P(EO)₂₀LiTFSI polymer electrolyte leads to the improvement of the thermal stability and the ionic conductivity (x = 1.27, 2.06 × 10⁻⁴ S cm⁻¹ at room temperature), and the reasonable lithium transference number is also obtained. The Li/LiFePO₄ cell using this polymer electrolyte shows promising reversible capacity, 120 mAh g⁻¹ at room temperature and 164 mAh g⁻¹ at 55 °C.     

Enabling the Li-ion conductivity of Li-metal fluorosulphates by ionic liquid grafting

Recently unveiled ‘alkali metal fluorosulphate (AMSO₄F)’ class of compounds offers promising electrochemical and transport properties. Registering conductivity value as high as 10⁻⁷ S cm⁻¹ in NaMSO₄F phases, we explored the fluorosulphate group to design novel compounds with high Li-ion conductivity suitable for solid electrolyte applications. In the process, we produced sillimanite-structured LiZnSO₄F by low temperature synthesis (T ≤ 300 °C). Examining this phase, we accidentally discovered the possibility of improving the ionic conductivity of poor conductors by forming a monolayer of ionic liquid at their particle surface. This phenomenon was studied by solid-state NMR, XPS and AC impedance spectroscopy techniques. Further, similar trends were noticed in other fluorosulphate materials like tavorite LiCoSO₄F and triplite LiMnSO₄F. With this study, we propose ‘ionic liquid grafting’ as an interfacial route to enable good Li-ion conductivity in otherwise poor conducting ceramics.     

Structural and electric properties of the Ce0.8(Sm1 ? xCax)0.2O2 ? δ system (x = 0.0–1.0)

CeO₂-based solid solutions with a fluorite structure are promising materials as electrolytes of medium-temperature electrochemical devices. This work presents the results of systematic studies of structural and electric properties and oxygen nonstoichiometry of the Ce_0.8(Sm_{1 − x} Ca _x )_0.2O_{2 − δ} system in a wide range of concentrations of 0 < x < 1 performed in order to establish the causes affecting the system conductivity and its behavior in a reducing medium. It is found that a single-phase solid solution of the fluorite type is formed in the whole concentration range. Parameters of its lattice cells decrease linearly at an increase in the concentration of Ca²⁺. Conductivity in air grows when calcium is added due to a decrease in the grain boundary resistance. The maximum conductivity in air was obtained for the composition of Ce_0.8(Sm_0.8Ca_0.2)_0.2O_{2 − δ} and is 13.71 × 10⁻³ S/cm at 873 K. Studies of the dependence of conductivity of the partial pressure of oxygen showed that electron conductivity is observed at a higher oxygen partial pressure at an increase in the temperature and calcium concentration. The critical partial pressure of oxygen ( p_O2 ^* )\left( {p_{O_2 }^* } \right) for the compositions of Ce_0.8(Sm_{1 − x} Ca _x )_0.2O_{2 − δ} with x = 0; 0.2, and 0.5 is 1.83 × 10⁻¹⁶, 1.73 × 10⁻¹³, and 3.63 × 10⁻¹³ atm at 1173 K, respectively, and 2.76 × 10⁻²¹, 5.05 × 10⁻¹⁸, and 1.31 × 10⁻¹⁸ atm at 1023 K.     

Preparation and ionic conductivity of poly(ethylene oxide) oligomers having thiolate groups on the chain ends

Poly(ethylene oxide) (PEO) oligomers having alkali metal thiolate groups on the chain ends (PEO _m -S⁻M⁺) were prepared as an ion conductive matrix. The molecular weight of the PEO part (m) and the content of the thiolate groups in the molecule were changed to analyze the effect of carrier ion concentration in the bulk. In a series of potassium salt derivatives, PEO₃₅₀-SK showed the highest ionic conductivity of 6.42 × 10⁻⁵ S/cm at 50 °C. In spite of a poor degree of dissociation which was derived from the acidity of the thiolate groups, PEO _m -SM showed quite high ionic conductivity among other PEO/salt hybrids. PEO _m -SM had glass transition temperatures (T _g) 20 °C lower than other PEO/salt hybrids. Lowering the T _g was concluded to be effective in providing higher ionic conductivity for PEO-based polymer electrolytes. Received: 30 April 1999 / Accepted: 20 June 1999     

Synthesis of electrospun BaSrTiO<Subscript>3</Subscript>/PVP nanofibers

Ba_1−x Sr _x TiO₃(x = 0–0.5, BST) nanofibers with diameters of 150–210 nm were prepared by using electrospun BST/polyvinylpyrrolidone (PVP) composite fibers by calcination for 2 h at temperatures in the range of 650–800 °C in air. The morphology and crystal structure of calcined BST/PVP nanofibers were characterized as functions of calcination temperature and Sr content with an aid of XRD, FT-IR, and TEM. Although several unknown XRD peaks were detected when the fibers were calcined at temperatures less than 750 °C, they disappeared with increasing the temperature (above 750 °C) due to its thermal decomposition and complete reaction in the formation of BST. In addition, the FT-IR studies of BST/PVP fibers revealed that the intensities of the O–H stretching vibration bands (at 3430 and 1425 cm⁻¹) became weaker with increasing the calcination temperature and a broad band at 540 cm⁻¹, Ti–O vibration, appeared sharper and narrower after calcination above 750 °C due to the formation of metal oxide bonds. However, no effect of Sr content on the crystal structure of the composites was detected.     

Thermal and dielectric properties of PEO/EC/Pr4N+I− polymer electrolytes for possible applications in photo-electro chemical solar cells

The anion-conducting polymer electrolyte polyethylene oxide (PEO)/ethylene carbonate (EC)/Pr₄N⁺I⁻/I₂ is a candidate material for fabricating photo-electrochemical (PEC) solar cells. Relatively high ionic conductivity values are obtained for the plasticized electrolytes; at room temperature, the conductivity increases from 7.6 × 10⁻⁹ to 9.5 × 10⁻⁵ S cm⁻¹ when the amount of EC plasticizer increases from 0% to 50% by weight. An abrupt conductivity enhancement occurs at the melting of the polymer; above the melting temperature, the conductivity can reach values of the order of 10⁻³ S cm⁻¹. The melting temperature decreases from 66.1 to 45.1 °C when the EC mass fraction is increased from 0% to 50%, and there is a corresponding reduction in the glass transition temperature from −57.6 to −70.9 °C with the incorporation of the plasticizer. The static dielectric constant values, , increase with the mass fraction of plasticizer, from 3.3 for the unplasticized sample to 17.5 for the 50% EC sample. The dielectric results show only small traces of ion-pair relaxations, indicating that the amount of ion association is low. Thus, the iodide ion is well dissociated, and despite its large size and relatively low concentration in these samples, the iodide ion to ether oxygen ratio is 1:68, a relatively efficient charge carrier. A further enhancement of the ionic conductivity, especially at lower temperatures, is however desired for these applications.     

Ionic conductivity of sodium silicates with lovozerite-type structure

The ionic conductivity of Na,Zr and Na,Sn silicates of the lovozerite family (Na_{8 − x} H _x ZrSi₆O₁₈ structural type, space group R $ \bar 3 $ \bar 3 m) was studied in the temperature range of 293–800 K using the impedance spectroscopy method (5−5 × 10⁵ Hz). The compositions of the studied compounds were obtained using the method of hydrothermal synthesis in the MO₂-SiO₂-NaOH-H₂O and MO₂-SiO₂-CaO-NaOH-H₂O (M = Zr, Sn) systems at 573–823 K. The samples for electrophysical studies were prepared according to the ceramic technology. It was found that isovalent cation substitutions of Sn⁴⁺ → Zr⁴⁺ in Na₈M⁴⁺Si₆O₁₈ and Na₆CaM⁴⁺Si₆O₁₈ and H⁺ → Na⁺ in Na_{8 − x} H _x ZrSi₆O₁₈ result in an increase in the ionic conductivity by 2–3 orders of magnitude, without affecting the ionic transport activation energy (0.6–0.7 eV). The best electrolytic characteristics are typical for the Na₅H₃ZrSi₆O₁₈ compound, for which the ionic conductivity value is 5 × 10⁻⁴ S/cm at 573 K.