等离子体条件Cu/SiO2对甲烷偶联的催化作用

It has been reported that methane coupling by plasma techniques with catalysts, such as direct current corona discharge with a Sr/La2O3 catalyst[1], dielectric-barrier discharge with zeolites[2] and pulsed corona discharge with metal oxide catalysts[3], give C2 hydrocarbons under atmospheric pressure. But acetylene predominates over other C2 hydrocarbons in the products. Our recent work reported that good results can be obtained for methane coupling under a pulsed corona plasma in the presence of hydrogen[4]. The addition of hydrogen improves the conversion of methane and the yield of C2 hydrocarbons. A methane conversion of 57.1% and a yield of C2 hydrocarbons of 43.4% were obtained at lower power, but acetylene was inevitably the main product. With the introduction of a Ni/γ-Al2O3 catalyst prepared by a cold plasma into the plasma reaction, the distribution of C2 hydrocarbons changed, and the content of C2H4 was 66.1%[5].     

Conversion of Methane to C2 Hydrocarbons via Cold Plasma Reaction

Direct conversion of methane to C2 hydrocarbons via cold plasma reaction with catalysts has been studied at room temperature and atmospheric pressure. Methane can be converted into C2 hydrocarbons in different selectivity depending on the form of the reactor, power of plasma, flow rate of methane, ratio of N2/CH4 and nature of the catalysts. The selectivity to C2 hydrocarbons can reach as high as 98.64%, and the conversion of methane as high as 60% and the yield of C2 hydrocarbons as high as 50% are obtained. Coking can be minimized under the conditions of: proper selection of the catalysts, appropriate high flow rate of inlet methane and suitable ratio of N2 to CH4. The catalyst surface provides active sites for radical recombination.     

Methane Coupling Using Hydrogen Plasma and Pt／γ—Al2O3 Catalyst

In this paper,methane coupling at ambient temperature, under atmospheric pressure and in the presence of hydrogen was firstly investigated by using pulse corona plasma and Pt/γ-Al2O3 catalyst. Experimental results showed that Pt/γ-Al2O3 catalyst has catalytic activity for methane couplin to C2H4. Over sixty percent o outcomes of C2 hydrocarbons were detected to be ethylene.     

Catalysis Conversion Methane into C2 Hydrocarbons via Electric Field Enhanced Plasma

In this paper the effect of catalyst and carrier in electric field enhanced plasma on methane conversion into C2 hydrocarbons was investigated. Methane coupling reaction was studied in the system of continuous flow reactor on Ni, MoO3, MnO2 catalysts and different ZSM-5 carriers. The per pass conversion of methane can be as high as 22%, the selectivity of ethylene can be as high as 23.8%, of acetylene 60.8%, of ethane 5.4% and of total C2 hydrocarbons was more than 90%. ZSM-5-25 was the better carrier and MnO2 was the better active component. The efficiency of energy was as high as 7.81%.     

Experimental investigation of fluidized-bed reactor performance for oxidative coupling of methane

Performance of the oxidative coupling of methane in fluidized-bed reactor was experimentally investigated using Mn-Na2WO4/SiO2,La2O3/CaO and La2O3-SrO/CaO catalysts.These catalysts were found to be stable,especially Mn-Na2WO4/SiO2 catalyst.The effect of sodium content of this catalyst was analyzed and the challenge of catalyst agglomeration was addressed using proper catalyst composition of 2%Mn2.2%Na2WO4/SiO2.For other two catalysts,the effect of Lanthanum-Strontium content was analyzed and 10%La2O 3-20%SrO/CaO catalyst was found to provide higher ethylene yield than La2O3/CaO catalyst.Furthermore,the effect of operating parameters such as temperature and methane to oxygen ratio were also reviewed.The highest ethylene and ethane (C2) yield was achieved with the lowest methane to oxygen ratio around 2.40.5% selectivity to ethylene and ethane and 41% methane conversion were achieved over La2O3-SrO/CaO catalyst while over Mn-Na2WO4 /SiO2 catalyst,40% and 48% were recorded,respectively.Moreover,the consecutive effects of nitrogen dilution,ethylene to ethane production ratio and other performance indicators on the down-stream process units were qualitatively discussed and Mn-Na2WO4/SiO2 catalyst showed a better performance in the reactor and process scale analysis.     

Study on the hydrogenation coupling of methane

At atmospheric pressure and ambient temperature, the hydrogenation coupling of methane was studied by using pulse corona plasma and its synergism with catalyst. The results showed that (i) under pulse corona plasma, the coupling of methane could be fulfilled by the addition of hydrogen, and with the increase of the amount of hydrogen, the conversion of methane and the yield of C2 hydrocarbon increased, and the deposit of carbon decreased; (ii) the conversion of methane was affected by pulse voltage and repeated frequency; (iii) in the system, the addition of Ni/y-AI203 could improve the distribution of C2 hydrocarbon; (iv) the activity of Ni/y-AI2O3 prepared by cold plasma was better than that by chemical methods. The experiment opened up a new technical route of the coupling of methane.     

OXIDATIVE COUPLING OF METHANE OVER Mn_2O_3-Na_2WO_4/SiO_2 CATALYST IN THE ABSENCE OF DILUTE GAS

The oxidative coupling of methane over Mn2O3-Na2WO4/SiO2 catalyst has been investigated in the absence of dilute gas. 16.4% of C2 yield and 80.4% of the selectivity to C2 hydrocarbons were obtained at CH4/O2 = 8.5/1.5. The effect of flow rate on the selectivity to C2 hydrocarbons and CH4 conversion was different under the reaction condition of different ratio of CH4 to oxygen. The flow rate had a more remarkable effect on the selectivity at the lower ratio of methane to oxygen. The addition of steam into the reaction gas can increase C2 yield to some extent, but that of HC1 decrease the selectivity to C2 hydrocarbons.     

In situ carbon nanotube synthesis by the reduction of NiO/γ-Al_2O_3 catalyst in methane

The synthesis of carbon nanotubes (CNTs) via chemical vapour deposition of methane on NiO/γ-Al2O3 catalyst has been investigated.The reduction behavior of NiO/γ-Al2O3 by methane was studied using thermogravimetric (TG) and X-ray diffraction (XRD) techniques.It was found that the NiO supported on γ-Al2O3,was reduced to Ni0 in methane atmosphere in the temperature range of 710-770℃.The catalytic activity of NiO/γ-Al2O3 for CNTs synthesis by in situ chemical vapour deposition of methane during the reduction was also investigated.Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to observe the CNTs produced at various reduction temperatures.The results indicated that the reduction temperature exhibits obvious influence on the morphology and the yield of CNTs.CNTs with the diameter of about 20 nm were obtained at reduction temperature of 750℃,and higher reduction temperature (such as 800 and 850℃) led to an increase in CNTs diameter and a decrease in CNTs yield.     

In situ carbon nanotube synthesis by the reduction of NiO/γ-Al2O3 catalyst in methane

The synthesis of carbon nanotubes (CNTs) via chemical vapour deposition of methane on NiO/γ-Al2O3 catalyst has been investigated. The reduction behavior of NiO/γ-Al2O3 by methane was studied using thermogravimetric (TG) and X-ray diffraction (XRD) techniques. It was found that the NiO supported on γ-Al2O3, was reduced to Ni⁰ in methane atmosphere in the temperature range of 710--770 ℃. The catalytic activity of NiO/γ-Al2O3 for CNTs synthesis by in situ chemical vapour deposition of methane during the reduction was also investigated. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to observe the CNTs produced at various reduction temperatures. The results indicated that the reduction temperature exhibits obvious influence on the morphology and the yield of CNTs. CNTs with the diameter of about 20 nm were obtained at reduction temperature of 750 ℃, and higher reduction temperature (such as 800 and 850 ℃) led to an increase in CNTs diameter and a decrease in CNTs yield.     

Preparation of Highly Active Pt-K/γ-Al2O3 Catalyst for o-Phenylphenol Synthesis from o-Cyclohexenyl-cyclohexanone Dehydrogenation

0.5%Pt-K/γ-Al2O3 catalysts for the synthesis of o-phenylphenol（OPP） from o-cyclohexenyl-cyclohexanone （dimer） dehydrogenation were prepared by means of a two subsequent impregnation method. The effects of catalyst preparation parameters, such as K promoters, calcination, and reduction conditions, were investigated. The results showed that the addition of K2SO4 to Pt/γ-Al2O3 catalyst notably promoted the selectivity of OPP, and its optimum content was found to be 6% in mass fraction. The higher activity was obtained when Pt/γ-Al2O3 catalyst was calcined in nitrogen atmosphere at 400--500 ℃ and then reduced at the same temperature for 3 h in hydrogen atmosphere. The conversion of the dimer and the selectivity of OPP were always above 99% and 90%, respectively, over 0.5%Pt-6% K2SO4/γ-Al2O3 catalyst during the pilot scale test of 8000 h.     

Combination of Partial Oxidation and CO2 Reforming of Methane over Monolithic Ni／CeO2-ZrO2／γ-Al2O3 Catalyst

A new monolithic Ni/CeO2-ZrO2/γ-Al2O3 catalyst for combined partial oxidation and CO2 reforming of methane was prepared. The result shows that the addition of O2 to the feed can improve the activity of the catalyst and adjust the H2/CO ratio of the productive gases.     

Effect of La_2O_3/γAl_2O_3 Catalyst on the Activation of CH_4 and CO_2 to C_02 Hydrocarbons under Non-equilibrium Plasma

The oxidative coupling of methane (OCM) to C2 hydrocarbons using carbon dioxide as oxidant is an attractive process from environmental point of view. Only a few research papers reported for it1-3. In general, the yield of C2 hydrocarbons was about 6%. This indicated that the method of catalytic activation was unfavorable to the reaction. It is necessary for us to find a new method in order to activate reaction and improve C2 hydrocarbon yield. Non-equilibrium plasma is a cold plasma in…     

Enhanced catalytic performance for direct synthesis of dimethyl ether from syngas over a La2O3 modified Cu-ZrO2/γ-Al2O3 hybrid catalyst

A series of hybrid catalysts were made by physically mixing Cu-ZrO 2 and γ-Al 2 O 3,for former it was modified with different loadings of La 2 O 3 prepared by co-precipitation method.The catalysts were characterized by BET,XRD,N 2 O-adsorption,EXAFS,H 2-TPR,NH 3-TPD techniques and evaluated in the synthesis of dimethyl ether from syngas.The results show that La 2 O 3 promoted catalysts displayed a significantly better catalytic performance compared with Cu-ZrO 2 /γ-Al 2 O 3 catalyst in CO conversion and DME selectivity,and the optimum catalytic activity was obtained when the content of La 2 O 3 was 12 wt%.The characterizations reveal that high copper dispersion,facile reducibility of copper particles and appropriate amount of acidic sites are responsible for the superior catalytic performance.     

Study of The Pd-B/ γ-Al2O3 Amorphous Alloy Catalyst

The Pd-B/γ-Al2O3 amorphous alloy catalyst and Pd/γ-Al2O3 crystalline metal catalyst were prepared by KBH4 reduction and routine impregnation,respectively.Pd-B/γ-Al2O3 and Pd/γ-Al2O3 catalysts were characterized by XRD and SEM.It was found that the catalytic activity of the Pd-B/γ-Al2O3 amorphous alloy catalyst was higher than that of the Pd/γ-Al2O3 crystalline metal catalyst in the anthraquinone hydrogenation.     

Methane conversion under cold plasma over Pd-containing ionic liquids immobilized on γ-Al2O3

Pd-containing ionic liquid（IL） 1-hexyl-3-methylimidazolium tetrafluoroborate（C₆MIMBF₄） immobilized on 7-Al₂O₃（Pd-IL/γ-Al₂O₃） was prepared and characterized by Fourier transform infrared spectroscopy（FTIR）,scanning electron microscopy（SEM） and Brunauer-Emmett-Teller （BET） analysis.The influences of C₆MIMBF₄ loading and Pd on methane conversion to C₂ hydrocarbons under cold plasma were investigated.FTIR and SEM analyses indicated that C₆MIMBF₄ had been successfully immobilized on 7-Al₂O₃ and the C₆MIMBF₄ showed excellent stability under cold plasma.The results of BET and methane conversion showed that with the increase in immobilization amount of C₆MIMBF₄ ontoγ-Al₂O₃,the specific surface area and pore volume of IL/γ-Al₂O₃ decreased,while the selectivity and yield of C₂ hydrocarbons increased.The selectivity of C₂ hydrocarbons was 94.6%when the loading of C₆MIMBF₄ was 40%,and the percentage of C₂H₄ in C₂ hydrocarbons was as high as 64%when using Pd-IL/γ-Al₂O₃ as a catalyst with no conventional thermal reduction treatment. Optical emission spectra（OES） from the cold plasma reactor during methane conversion were also studied.The results indicated that the intensity of the C₂,CH,H,and C active species from methane and hydrogen decomposition increased when IL/γ-Al₂O₃ or Pd-IL/γ-Al₂O₃ was introduced into the plasma system.Based on the analyses of the gas product and OES spectra,it can be concluded that the surface catalyzed reactions between plasma and ionic liquid were very important for the reduction of Pd²⁺ and the formation of C₂H₄.     

Study of CO2 Hydrogenation to Methanol over Cu-V/γ-Al2O3 Catalyst

The effect of vanadium addition to CU/γ-Al2O3 catalyst used in the hydrogenation of CO2 to produce methanol was studied. It was found that the catalytic performance of the Cu-based catalyst improved after V addition. The influence of reaction temperature, space velocity and the molar ratio of H2 to CO2 on the performance of 12%Cu-6%V/γ-Al2O3 catalyst were also studied. The results indicated that the best conditions for reaction were as follows: 240℃, 3600 h-1 and a molar ratio of H2 to CO2 of 3:1. The results of XRD and TPR characterization demonstrated that the addition of V enhanced the dispersion of the supported CuO species, which resulted in the enhanced catalytic performance of CU-V/γ-Al2O3 binary catalyst.     

Methane Decomposition over Ni/α-Al2O3 Promoted by La2O3 and CeO2

The decomposition of methane on Ni/a-Al2O3 modified by La2O3 and CeO2 with differ-ent contents has been investigated and the ralationship between methane decomposition and removal of carbon by CO2 over these catalyst has also been studied by pulse-chromatography. The catalysts were characterized by TPR and XRD. It was shown that Ni/a-Al2O3 could be promoted by adding La2O3, and the carbon species produced over this catalyst was activated and eliminated by CO2. But CeO2 would suppress the decomposition of methane over Ni crystallite. Both La2O3 and CeO2 can inhibit aggregation of the Ni particles. Decomposition of methane over the Ni-based catalysts is structure sensitive to a certain extent.     

Metathesis of Butylene-2 and Ethylene to Propylene over 3.0Mo／（Hβ＋γ-Al2O3） Catalysts with Different γ-Al2O3 Contents

A series of 3. OMo/(Hβ γ-Al2O3) samples with γ-Al2O3 contents in the range of 0-100% (mass fraction) was studied by means of XRD, NH3-TPD, TPR and BET determinations for characterizing their structures. The Hβ zeolite structure in the 3.0Mo/Hβ sample can be effectively stabilized by adding some γ-Al2O3 to Hβ zeolite. γ-Al2O3 mainly favors the formation of polymolybdate or multilayered Mo oxide, while Hβ mainly forms the Al2(MoO4)3 species, as evaluated by the TPR technique. When used as the catalyst for the metathesis of butylene-2 and ethylene to propylene, there exists a close correlation between the specific surface area and stability of the catalyst. The specific surface area of the catalyst shows the maximum when (Hβ γ-Al2O3) contains 30%γ-Al2O3, which is in agreement with that of the time needed for the reaction stablization. In the case of maximum surface area, the rate of coke deposition is the minimum.     

Conversion of natural gas to C_2 hydrocarbons through dielectric-barrier discharge plasma catalysis

The experiments are carried out in the system of continuous flow reactors with dielectric-barrier discharge (DBD) for studies on the conversion of natural gas to C2 hydrocarbons through plasma catalysis under the atmosphere pressure and room temperature. The influence of discharge frequency, structure of electrode, discharge voltage, number of electrode, ratio of H2/CH4, flow rate and catalyst on conversion of methane and selectivity of C2 hydrocarbons are investigated. At the same time, the reaction process is investigated. Higher conversion of methane and selectivity of C2 hydrocarbons are achieved and deposited carbons are eliminated by proper choice of parameters. The appropriate operation parameters in dielectric-barrier discharge plasma field are that the supply voltage is 20-40 kV (8.4-40 W), the frequency of power supply is 20 kHz, the structure of (b) electrode is suitable, and the flow of methane is 20-60 ml · min-1. The conversion of methane can reach 45%, the selectivity of C2 hydrocarbons i     

Surface Acidity／Basicity and Catalytic Reactivity of CeO2／γ—A12O3 Catalysts for the Oxidative Dehydrogenation of Ethane with Carbon Dioxide to Ethylene

Dehydrogenation of ethane to ethylene in CO2 was investigated over CeO2/γ-Al2O3 catalysts at 700℃ in a conventional flow reactor operating at atmospheric pressure. XRD, BET and microcalorimetric adsorption techniques were used to characterize the structure and surface acidity/basicity of the CeO2/γ-Al2O3 catalysts. The results show that the surface acidity decreased while the surface basicity increased after the addition of CeO2 to γ-Al2O3. Accordingly, the activity of the hydrogenation reaction of CO2 increased, which might be responsible for the enhanced conversion in the dehydrogenation of ethane to ethylene. The highest ethane conversion obtained was about 15% for the 25?O2/γ-Al2O3. The selectivity to ethylene was high for all the CeO2, γ-Al2O3 and CeO2/γ-Al2O3 catalysts.