可见光辐射下活性炭-铁酸镍杂化催化剂光催化氧化氨氮

铁酸镍（NiFe₂O₄）中的镍原子抑制其光芬顿催化活性. 然而,活性炭（AC）能激活其光芬顿催化活性,结果导致复合催化剂AC-NiFe₂O₄在过氧化氢存在时可见光辐射下也可催化氧化氨氮. 用X射线衍射（XRD）,透射电镜（TEM）,傅里叶变换红外（FTIR）光谱,紫外-可见漫反射光谱（UV-Vis DRS）,比表面积和振动样品磁强计对催化剂进行了表征. 光催化降解氨氮的实验表明,该复合催化剂在10 h内氨氮的降解率可达到91.0%,而同样条件下没有催化剂时氨氮的去除率只有24.0%. 对照实验表明,裸铁酸镍在可见光辐射下,氨氮的降解率只有30.0%. 这表明活性炭加速了氨氮的氧化速率. 动力学研究表明,氨氮的氧化遵循一级反应动力学规律,其表观反应动力学常数为3.538×10^-3 min^-1. 机理研究表明,氨氮的氧化是通过生成HONH₂ 中间体,然后转化为NO₂^- .8次循环实验表明该复合催化剂容易分离、可循环使用、且催化活性十分稳定. 因此,该催化剂具有潜在的应用价值.     

Selective vapor‐phase oxidation of o‐xylene to phthalic anhydride over Co‐Mn/H3PW12O40@TiO2 using molecular oxygen as a green oxidant

The oxidation of o‐xylene to phthalic anhydride over Co‐Mn/H₃PW₁₂O₄₀@TiO₂ was investigated. The experimental results demonstrated that the prepared catalyst effectively catalyzed the oxidation of o‐xylene to phthalic anhydride. Also, the synergistic effect between three metals plays vital roles in this reaction. From a green chemistry point of view, this method is environmentally friendly due to carrying out the oxidation in a fixed‐bed reactor under solvent‐free condition and using molecular oxygen as a green and cheap oxidizing agent. The resulting solid catalysts were characterized by FT‐IR, XRD, XPS, ICP‐OES, FESEM, TEM, EDX, DR‐UV spectroscopy, BET and thermogravimetric analysis. The oxidation of o‐xylene yields four products: o‐tolualdehyde, phthaldialdehyde, phthalide and finally phthalic anhydride as the main product. The reaction conditions for oxidation of o‐xylene were optimized by varying the temperature, weight hourly space velocity and oxygen flow rate (contact time). The optimum weight percentage of phosphotungstic acid (HPW) and Co/Mn for phthalic anhydride production were 15 wt % and 2 wt%, respectively. The best Co/Mn ratio was found to be 10/1. Oxygen flow rate was very important on the phthalic anhydride formation. The optimum conditions for oxidation of o‐xylene were T = 370 °C, WHSV = 0.5 h^?1 and oxygen flow rate = 10 mL min^?1. Under optimized conditions, a maximum of 88.2% conversion and 75.5% selectivity to phthalic anhydride was achieved with the fresh catalyst. Moreover, reusability of the catalyst was studied and catalytic activity remained unchanged after at least five cycles.     

Chemical composition optimization and characterization of the NiO/B<Subscript>2</Subscript>O<Subscript>3</Subscript>-Al<Subscript>2</Subscript>O<Subscript>3</Subscript> system as a catalyst for ethylene oligomerization

The samples of the NiO/B₂O₃-Al₂O₃ system with NiO contents from 0.48 to 38.30 wt % were synthesized by the impregnation of borate-containing alumina (20 wt % B₂O₃). It was found that nickel oxide occurred in an X-ray amorphous state in the samples containing to 23.20 wt % NiO. At a NiO content of 4.86 wt % or higher, the support was blocked by the modifier to cause a decrease in the specific surface area from 234 to 176 m²/g and in the amount of acid sites from 409–424 to 333 μmol/g. An extremal character of the dependence of catalyst activity in ethylene oligomerization on NiO content was found with a maximum in the range of 4.86–9.31 wt %. Based on spectroscopic data, it was found that ethylene activation on the NiO/B₂O₃-Al₂O₃ catalyst can be associated with the presence of Ni²⁺ cations, which chemically interact with the support. The catalyst containing 4.86 wt % NiO at 200°C, a pressure of 4 MPa, and an ethylene supply rate of 1.1 h⁻¹ provided almost complete ethylene conversion at the yield of liquid oligomerization products to 90.0 wt %; the total concentration of C⁸⁺ alkenes in these products was 89.0 wt %.     

Selective oxidation of anthracene to 9,10-anthraquinone over silica supported vanadium catalyst

The inner-ring oxidation of anthracene over V₂O₅/SiO₂ catalyst was investigated at various oxygen concentrations, contact times of the reactants and reaction temperatures. Up to 90 % yield to 9,10-anthraquinone is obtained at 218-220^oC.     

Catalytic oxidation of methane over Pd/Co3O4

The catalytic activity of Pd/Co₃O₄ toward methane oxidation has been examined in this study as a function of Pd loading, reaction temperature, space velocity and methane concentration in the reaction gas mixture. The bare oxide is quite active achieving a 100% methane conversion at 480°C under the reaction conditions used. The catalyst with the highest Pd loading tested of 10 wt.% yields the best activity curve, but the 5 wt.% Pd/Co₃O₄ catalyst performs nearly as well. Complete conversion for this catalyst is attained at 300°C and the activity remains stable over a 90-min test period.     

Kinetic Peculiarities in the Low-Temperature Oxidation of H2S on Vanadium Catalysts

H₂S oxidation by oxygen on catalysts V₂O₅/Al₂O₃, V₂O₅/TiO₂, V₂O₅/Al₂O₃/TiO₂ was studied at temperatures below the sulfur dew point. High activity and the oscillation character of the oxidation were demonstrated by catalysts with low contents of V₂O₅ (3–5 wt.%). The increase in the V₂O₅ concentration to 10–20 wt.% results in the reduction of the catalytic activity and oscillation ability. On a pure V₂O₅ catalyst, the oscillations were not detected. The difference between the catalysts with the high and low concentrations of V₂O₅ is explained in terms of the structures of the V⁵⁺ species formed in the catalysts. This revised version was published online in June 2006 with corrections to the Cover Date.     

KCl对Cu-K-La/γ-Al2O3催化剂上HCl氧化反应性能的影响

采用等体积浸渍法制备了Cu-K-La/γ-Al₂O₃催化剂,考察了KCl对该催化剂催化HCl氧化制Cl₂反应性能的影响. 当KCl的负载量为5 wt%时,Cu-K-La/γ-Al₂O₃催化剂表现出较好的催化活性和稳定性,可在较大的原料气空速变化范围内使用. 在0.1 MPa,360 ℃,空速450 L/（kg-cat·h）和HCl/O₂摩尔比为2：1的反应条件下,Cu-K-La/γ-Al₂O₃催化剂上HCl转化率在100 h内保持85%以上. 表征结果表明,Cu,K和La物种均高度分散于γ-Al₂O₃载体表面;一定量KCl的加入可降低Cu²⁺ → Cu⁺的还原温度,从而提高Cu²⁺活性中心的催化活性.     

Study of the selectivity of a V2O5?ZrO2 catalyst for partial oxidation ofo-xylene at high temperatures

It has been established that at high temperatures (above 450°C) the V₂O₅−ZrO₂ catalyst exhibits a higher selectivity in the oxidation ofo-xylene to phthalic anhydride than does the conventional V₂O₅−TiO₂(a) catalyst. The catalyst selectivity is found to increase with respect to partial oxidation ofo-xylene, the valuable by-product maleic anhydride being obtained. Studies by different physicochemical methods have shown that V₂O₅−ZrO₂ undergoes no significant phase and structural changes under high-temperature conditions.     

Catalytic oxidation of benzene at low temperature over novel combination of metal oxide based catalysts: CuO,MnO2, NiO with Ce0.75Zr0.25O2 as support

Mesoporous Ce_0.75Zr_0.25O₂ solid solution powders were successfully synthesized by a co-precipitation method. A combination of 10 wt% copper oxide, manganese oxide, and nickel oxide was added to the Ce_0.75Zr_0.25O₂ support by impregnation method and calcined in the air with a flow rate of 2 ml s^?1 at 400 °C for 4 h. All catalysts were characterized using Hydrogen Temperature Programmed Reduction (H₂-TPR), X-ray Diffraction (XRD), and Brunauer-Emmet-Teller (BET) isotherm methods to find the interaction between metals, the crystallinity of the catalyst, surface area and pore volume of the catalyst, respectively. The 3.3% CuO-3.3% MnO₂-3.3% NiO/Ce_0.75Zr_0.25O₂ catalyst showed higher catalytic activity for benzene oxidation with benzene conversion of 90% at 250 °C and weight hourly space velocity (72,000 mL g^?1 h^?1) when compared to one metal oxide only. This finding presents a high activity and low-cost catalysts for removing a very lean concentration of benzene containing in the industrial flue gas at low temperatures.     

钙铝石涂层对整体型钙钛矿氧化物催化剂活性和热稳定性的影响

 采用固相反应法合成了钙铝石材料 12SrO•7Al2O3, 并以此作为涂层制备了堇青石蜂窝陶瓷型 La0.8Sr0.2MnO3 整体催化剂, 在不同温度 (850~1 050 oC) 下对该催化剂进行了热处理, 并采用 N2 吸附-脱附、X 射线衍射和扫描电镜等手段对其进行了表征, 考察了其催化甲基丙烯酸甲酯燃烧反应的活性. 结果表明, 12SrO•7Al2O3 作为涂层明显改善了整体催化剂的热稳定性, 在 850 oC 下焙烧 6 h 后, 含有 12SrO•7Al2O3 涂层的整体催化剂在 260 oC 即可将甲基丙烯酸甲酯完全转化. 12SrO•7Al2O3 涂层可避免 La0.8Sr0.2MnO3 活性组分与堇青石的接触, 减轻了活性组分在催化剂表面的烧结, 有利于保持 La0.8Sr0.2MnO3 活性组分的晶体结构和分散度, 提高整体催化剂的活性和热稳定性.     

Development of a Ni–Pd/CeZrO<Subscript>2</Subscript>/Al<Subscript>2</Subscript>O<Subscript>3</Subscript> catalyst for the effective conversion of methane into hydrogen-containing gas

The effects of the Pd content (0–1 wt %) and the synthesis method (joint impregnation with Ni + Pd and Pd/Ni or Ni/Pd sequential impregnation) on the physicochemical and catalytic properties of Ni–Pd/CeZrO₂/Al₂O₃ were studied in order to develop an efficient catalyst for the conversion of methane into hydrogen-containing gas. It was shown that variation in the palladium content and a change in the method used for the introduction of an active constituent into the support matrix make it possible to regulate the redox properties of nickel cations but do not affect the size of NiO particles (14.0 ± 0.5 nm) and the phase composition of the catalyst ((γ + δ)-Al₂O₃, CeZrO₂ solid solution, and NiO). It was established that the activity of Ni–Pd catalysts in the reaction of autothermal methane reforming depends on the method of synthesis and increases in the following order: Ni + Pd < Ni/Pd < Pd/Ni. It was found that, as the Pd content of the Ni–Pd/CeZrO₂/Al₂O₃ catalyst was decreased from 1 to 0.05 wt %, the ability for self-activation, high activity, and operational stability of the catalyst under the conditions of autothermal methane reforming remained unaffected: at 850°C, the yield of hydrogen was ~70% at a methane conversion of ~100% during a 24-h reaction.     

Plasma-Catalytic Oxidation of Toluene on MnxOy at Atmospheric Pressure and Room Temperature

Mn_xO_y/SBA-15 catalysts were prepared via the impregnation method and utilized for toluene removal in dielectric barrier discharge plasma at atmospheric pressure and room temperature. The catalysts were characterized by X-ray diffraction, N₂ adsorption–desorption, Raman spectroscopy, X-ray photoelectron spectroscopy, H₂ temperature-programmed reduction, and O₂ temperature-programmed desorption methods. The characterization results indicated that manganese loading did not influence the 2D-hexagonal mesoporous structure of SBA-15. The catalyst had various oxidation states of manganese (Mn²⁺, Mn³⁺, and Mn⁴⁺), with Mn³⁺ being the dominant oxidation state. Toluene removal was investigated in the environment of pure N₂ and 80 % N₂ + 20 % O₂ plasma, showing that the toluene removal efficiency and CO₂ selectivity were noticeably increased by Mn_xO_y/SBA-15, especially in the presence of 5 % Mn/SBA-15. This activity was closely related to the high dispersion of 5 % Mn on SBA-15 and the lowest reduction temperature exhibited by this catalyst. Mn loading increased the yield of CO₂ in the N₂ plasma and promoted the deep oxidation of toluene. During toluene oxidation, oxygen exchange might follow a pathway, wherein bulk oxygen was released from the Mn_xO_y/SBA-15 surface; gas-phase O₂ subsequently filled up the vacancies created on the oxide. Each of the manganese oxidation states played an important role; Mn₂O₃ was considered as a bridge for oxygen exchange between the gas phase and the catalyst, and Mn₃O₄ mediated transfer of oxygen between the catalyst and toluene.     

Nickel-copper-chromium catalyst for selective methane oxidation to synthesis gas at short residence times

Data on the selective oxidation of methane to synthesis gas on a 9% NiCuCr/2% Ce/(ϑ + α)-Al₂O₃ catalyst in dilute mixtures with Ar at short residence times (2–3 ms) are presented. The composition, structure, morphology, and adsorption properties of the catalyst with respect to oxygen and hydrogen before and after reaction were studied using XRD, BET, electron microscopy with electron microdiffraction, TPR, TPO, and TPD of oxygen and hydrogen. The following optimum conditions for the preparation and pretreatment of the catalyst for selective methane reduction were found: the incipient wetness impregnation of a support with aqueous nitrate solutions; drying; and heating in air at 873 and then at 1173 K (for 1 h at either temperature) followed by reduction with an H₂-Ar mixture at 1173 K for 1 h. At a residence time of 2–3 ms (space velocity to 1.5 × 10⁶ h⁻¹) and 1073–1173 K, the resulting catalyst afforded an 80–100% CH₄ conversion in mixtures with O₂ (CH₄/O₂ = 2: 1) diluted with argon (97.2–98.0%) to synthesis gas with H₂/CO = 2: 1. The selectivity of CO and H₂ formation was 99.6–100 and 99–100%, respectively; CO₂ was almost absent from the reaction products. The catalyst activity did not decrease for 56 h; carbon deposition was not observed. A possible mechanism of the direct oxidation of CH₄ to synthesis gas is considered.     

Ni_2P/TiO_2-Al_2O_3催化剂的制备及其加氢脱硫、脱氮性能

采用溶胶-凝胶法制备了TiO2-Al2O3复合载体,采用浸渍法制备了Ni2P/TiO2-Al2O3催化剂,并用X射线衍射(XRD)、N2吸附比表面积(BET)测定、热重-差热分析(TG-DTA)、X射线光电子能谱(XPS)等技术对催化剂的结构和性质进行了表征.催化剂加氢脱硫(HDS)和脱氮(HDN)活性评价在实验室固定床连续反应装置上,以噻吩和吡啶为模型反应物进行.考察了不同载体、Ni2P负载量、标称Ni/P摩尔比、催化剂焙烧温度对Ni2P/TiO2-Al2O3催化剂上同时进行的噻吩加氢脱硫和吡啶加氢脱氮性能的影响.结果表明,TiO2含量为80%(w)的TiO2-Al2O3复合氧化物为载体,Ni2P负载量为30.0%(w),标称Ni/P摩尔比为1/2,催化剂焙烧温度为500℃时,Ni2P/TiO2-Al2O3催化剂加氢脱硫脱氮活性最高.在360℃,3.0MPa,氢油比800(V/V),液时体积空速1.5h-1的条件下,噻吩HDS和吡啶HDN转化率分别为61.32%和64.43%.     

Deactivation of Iron-Gallium Oxide Catalyst for Ammonia Oxidation

An iron-gallium oxide catalyst (97.0 wt % Fe₂O₃, 3.0 wt % Ga₂O₃) was studied in high-temperature oxidation of ammonia. Reasons for the deactivation of the catalyst at elevated temperature were analyzed.     

Dehydrogenation of isopropanol on a cerium-nickel catalyst

The effect of a cerium additive on the catalytic activity of a 2 wt % Ni/SiO₂ catalyst is studied. It found that under both flow and static conditions the activity of (2 wt % Ni + 0.2 wt % Ce)/SiO₂ catalyst is higher than that of the original sample; the increase in activity results from a sharp increase in the number of active sites. A change in the composition of the surface layer of the catalysts is analyzed by X-ray photoelectron spectroscopy. It was found that the fraction of nickel decreases and the fraction of carbon increases in cerium-containing catalyst. An explanation of the change in the elemental composition of the catalytic active sites of a nickel catalyst in the presence of cerium is proposed on the basis of XPS data and previous quantum chemical calculations.     

Two-stage catalytic system of Sn/Al2O3 and Pt/Al2O3for NO reduction by propene in lean conditions

The Pt/Al₂O₃, Sn/Al₂O₃catalysts were prepared by the single sol-gel method. The two-stage Sn/Al₂O₃and Pt/Al₂O₃catalyst in series for NO reduction with propene were investigated. The coexistance of water vapor enhanced the activity at medium temperature of 300-400^oC, and the NO conversion was above 50% at 225 to 500^oC even in the presence of water vapor and SO₂. This revised version was published online in August 2006 with corrections to the Cover Date.     

Selective methanation of CO in the presence of CO<Subscript>2</Subscript> in hydrogen-containing mixtures on nickel catalysts

The screening of commercial nickel catalysts for methanation and a series of nickel catalysts supported on CeO₂, γ-Al₂O₃, and ZrO₂ in the reaction of selective CO methanation in the presence of CO₂ in hydrogen-containing mixtures (1.5 vol % CO, 20 vol % CO₂, 10 vol % H₂O, and the balance H₂) was performed at the flow rate WHSV = 26000 cm³ (g Cat)⁻¹ h⁻¹. It was found that commercial catalytic systems like NKM-2A and NKM-4A (NIAP-07-02) were insufficiently effective for the selective removal of CO to a level of <100 ppm. The most promising catalyst is 2 wt % Ni/CeO₂. This catalyst decreased the concentration of CO from 1.5 vol % to 100 ppm in the presence of 20 vol % CO₂ in the temperature range of 280–360°C at a selectivity of >40%, and it retained its activity even after contact with air. The minimum outlet CO concentration of 10 ppm at 80% selectivity on a 2 wt % Ni/CeO₂ catalyst was reached at a temperature of 300°C.     

The influence of the active component and support nature, gas mixture composition on physicochemical and catalytic properties of catalysts for soot oxidation

Physicochemical and catalytic properties of compositions Fe(Ce)–Mn–O/support (gamma-, theta-, alpha-Al₂O₃, SiO₂ as the support) and Pt/CeO₂/theta-Al₂O₃ for oxidation of soot were characterized. It was established that the phase composition of the initial catalysts depended mainly on the nature of the active component and preparation conditions. Non-isothermal treatment of the soot–catalyst compositions at the temperature up to 1000 °C resulted in a change in the phase composition depending mainly on the final treatment temperature. The catalyst surface area was determined by the support nature. It was established that catalyst activities for oxidation of soot are determined by both catalyst nature and composition of gas mixture. The process of the soot oxidation is thought to involve oxygen from the catalyst surface. The higher proportion of weakly bound surface oxygen, the higher was the catalyst activity. An increase in the oxygen concentration from 5% O₂/N₂ to 15% O₂/N₂ is shown to lead to a decrease of the temperature of the soot oxidation. The influence of the oxygen concentration on the process of soot oxidation becomes weaker in the presence of water vapor. Results showed that the presence of NO in the gas mixture favors a decrease in the oxidation temperature of the soot, the higher being the nitrogen oxide concentration, the more pronounced effect. Introduction of SO₂ in amount of 50 ppm in the gas mixture has no noticeable effect on the process of the soot oxidation. Among the catalysts under study, Fe–Mn–K–O/gamma-Al₂O₃ is most effective to oxidation of the soot at otherwise identical conditions.     

Decomposition of nitrous oxide on AlFe-PILC catalyst

Summary Two AlFe-PILC catalysts were prepared with different OH/metal ratio and applied in nitrous oxide (N₂O) decomposition reactions. The 100% conversion of N₂O with NH₃into N₂and H₂O was achieved below 500^oC with both applied catalysts. However, the activity of catalysts in direct conversion of N₂O into N₂and O₂did not exceed 40 % below 500^oC. In this reaction the activity of AlFe-PILC catalyst synthesized at higher OH/metal ratio (4) is higher compared to the activity of AlFe-PILC catalyst with OH/metal ratio (2). Free FeO·Fe₂O₃particles were registered in the AlFe-PILC catalyst with higher OH/metal ratio (4).