Distribution of lattice-strain on partly nitrogen-covered Cu(0 0 1) surfaces

In-plane elastic lattice strain on the Cu(0 0 1)-c(2 × 2)N surfaces is investigated by scanning tunneling microscopy on the surface where nitrogen-adsorbed patches with average size of 5 × 5 nm² (c(2 × 2)N patches) are well separated by wide clean Cu surface. The lattice distortion on clean Cu surface is recognized in the vicinity of the boundary to a c(2 × 2)N patch. The positions of the protrusions observed on the c(2 × 2)N patch are compared with the surrounding undistorted (1 × 1) lattice of the clean Cu surface. Most of the protrusions on the c(2 × 2)N patches locate on the fourfold hollow sites of the undistorted Cu lattice. The lattice distortion is significant only near the boundary to the surrounding clean Cu surface.     

Self-consistent electronic structure calculation for nitrogen chemisorbed on copper (100)

A fully self-consistent calculation of the electronic structure of a N covered Cu slab is reported. The density of states shows changes relative to a clean Cu slab that reproduce the changes observed in photoemission spectra when N is chemisorbed on Cu(100). Thus initial state information is correctly mirrored in the photoemission spectra in this case. The changes are due to the presence of the N 2p-bands, and to significant alteration of the surface Cu 3d-bands by the chemisorption of N. The localization in space of the chemisorption bond and the importance of self-consistency are demonstrated.     

Nanopattern formation on Cu(0 0 1) surface coadsorbed with nitrogen and oxygen

Strain-induced nanopatterns formed by the coadsorption of nitrogen and oxygen atoms are studied on the Cu(0 0 1) surface by scanning tunneling microscopy. A square grid pattern similar to that on the N-adsorbed surface appears, and consists of square c(2 × 2) areas with adsorbed N and O atoms when the total density of the adsorbates is around 30% of the Cu atom density on the clean surface. We evaluated the surface strain using a first-principles calculation for a coadsorbed surface and compared it with those on the clean and N-adsorbed surfaces. The strain on the coadsorbed surface is smaller than that of the N-adsorbed surface. The observed size of the square c(2 × 2) area on the coadsorbed surface is larger than that on the N-adsorbed surface with increasing the density of the adsorbates on average as expected by the strain reduction. On the other hand, there is no significant difference in the period of the grid pattern.     

Cu(100)表面c(2×2)-N原子结构与吸附行为研究

用密度泛函理论的总能计算研究了金属铜(100)面的表面原子结构以及氮原子的c(2×2)吸附状态.研究结果表明：在Cu(100) c(2×2)-N表面系统中，氮原子处于四度配位的空洞(FFH)位置，距离最表面铜原子层的垂直距离为0.20?，最短的Cu—N键长度为1.83?.结构优化的计算否定了被吸附物导致的表面再构模型，即c(2×2)元胞的两个铜原子在垂直于表面方向发生相对位移，一个铜原子运动到氮原子之上的模型.该吸附表面的功函数约为4.65eV, 氮原子的平均吸附能为4.92 eV(以孤立氮原子为能量参考点).计算结果还说明，Cu—N杂化形成的表面局域态的位置在费米面以下约1.0 eV附近出现，氮原子和第一层以及第二层铜原子均有不同程度的杂化作用.该结果为最近有关该表面的STM图像的争论提供了判据性的第一性原理计算结果. 关键词： Cu(100) c(2×2)-N 表面吸附态 密度泛函总能计算     

Two-dimensional unoccupied electronic band structure of clean Cu(110) and (1 × 2) Na/Cu(110)

Using the technique of angle-resolved inverse photoemission, we have measured the dispersion of an unoccupied Cu(110) surface state for the clean Cu(110) surface and for the (1 × 2) reconstructed Na/Cu(110) surface along the symmetry lines. The dispersion of the crystal-induced surface state of clean Cu(110) at 2.05 eV above the Fermi energy at the point of the SBZ is free-electron-like with an effective mass of (1.0 ± 0.2)m_e at the point, which is in good agreement with other experimental results as well as a theoretical calculation. This surface state shifts to 2.5 eV above the Fermi energy for the (1 × 2) phase of Na/Cu(110) with a coverage of 0.25 ML, and the dispersion along the direction is considerably reduced compared to the clean surface. On the other hand, the dispersion of this state for (1 × 2) Na/Cu(110) (0.25 ML) along the direction is close to that of clean Cu(110). We account for these results within a missing-row picture of the Na-induced reconstruction.     

Electronic states of moiré modulated Cu films

We examined by low-energy electron diffraction and scanning tunneling microscopy the surface of thin Cu films on Pt(111). The Cu/Pt lattice mismatch induces a moiré modulation for films from 3 to about 10?ML thickness. We used angle-resolved photoemission spectroscopy to examine the effects of this structural modulation on the electronic states of the system. A series of hexagonal- and trigonal-like constant energy contours is found in the proximity of the Cu(111) zone boundaries. These electronic patterns are generated by Cu sp-quantum well state replicas, originating from multiple points of the reciprocal lattice associated with the moiré superstructure. Layer-dependent strain relaxation and hybridization with the substrate bands concur to determine the dispersion and energy position of the Cu Shockley surface state.     

XPS,UPS and thermal desorption studies of alcohol adsorption on Cu(110): I. Methanol

The adsorption of methanol on clean and oxygen dosed Cu(110) surfaces has been studied using temperature programmed reaction spectroscopy (TPRS), ultra-violet photoelectron spectroscopy (UPS) and X-ray photoelectron spectroscopy (XPS). Methanol was adsorbed on the clean surface at 140 K in monolayer quantities and subsequently desorbed over a broad range of temperature from 140 to 400 K. The UPS He (II) spectra showed the 5 highest lying emissions seen in the gas phase spectrum of methanol with a chemisorption bonding shift of the two highest lying orbitais due to bonding to the surface via the oxygen atom with which these orbitals are primarily associated. A species of quite a different nature was produced by heating this layer to 270 K. Most noticeably the UPS spectrum showed only 3 emissions and the maximum coverage of this state was approximately $\text{1}\text{2}$ monolayer. The data are indicative of the formation of a methoxy species, thus showing that methanol is dissociated on the clean Cu(110) surface at 270 K. The same dissociated species was observed on the oxygen dosed surface, the main difference in this ease being the production of large amounts of H₂CO observed in TPRS at 370 K.     

Random fields and the partially paramagnetic state of CsCo0.83Mg0.17Br3: critical scattering study

We have performed measurements of the critical neutron scattering on CsCo0.83Mg0.17Br3, a dilute stacked triangular lattice (STL) Ising antiferromagnet (AF). A two component line shape associated with the critical fluctuations appears at a temperature coincident with T(N1) observed in pure CsCoBr3. Such scattering is indicative of fluctuations in prototypical random field Ising model (RFIM) systems. The random field domain state arises in this case due to geometrical frustration within the STL Ising AF, which gives rise to a three sublattice Néel state, in which one sublattice is disordered. Magnetic vacancies nucleate AF domains in which the vacancies reside on the disordered sublattice thereby generating a RFIM state in the absence of an applied magnetic field.     

Oxygen induced surface segregation of Cu on the Au0.7Cu0.3(100) surface

The oxygen induced surface segregation of Cu on the Au_0.7Cu_0.3(100) surface was investigated by means of LEED and AES techniques. The dissociative adsorption of O₂ did not take place on this clean surface for a long time exposure at least up to 10⁴ L, and so the oxygen was forcibly introduced onto the surface through a pre-deposition of few a layers of Cu and its successive oxidation. The oxygen coverage was controlled by a heat treatment, which leads the system to a thermal equilibrium state. For the clean surface, the segregation of Au was clearly observed and the surface concentration of Au was estimated to be about 86%, greater than the bulk concentration of 70%. At low coverages below 0.16 ML, no remarkable oxygen induced segregation of Cu was observed. But, above 0.2 ML, the surface concentration of Cu was proportional to the oxygen coverage. The (2 × 4) LEED pattern was observed in a wide range of oxygen coverage. The maximum intensity of the (2 × 4) was observed at about 0.45 ML.     

Electron-phonon interaction in the quantum well state of the 1 ML Na/Cu(111) system

The electron-phonon interaction in the quantum well state formed by a Na monolayer coating on Cu(111) is investigated theoretically. The calculations show that the electron-phonon coupling constant γ in this state decreases insignificantly (≈1%) compared to the value of γ for a clean copper surface. The corresponding electron-phonon contribution to the lifetime τ of the quantum well state increases by a factor of 1.5 compared to τ for the clean Cu(111) surface.     

Surface quantum well state at the striped Cu(1 1 0)(2 × 1)O surface studied by angle resolved photoemission spectroscopy

We have performed an angle resolved photoemission spectroscopy with high energy and high momentum resolutions and have observed the k dependent energy dispersion curves of the striped Cu(1 1 0)(2 × 1)O surface. It is found that the Shockley surface state electron is confined in the clean surface along the perpendicular direction to the stripes and forms a quantum well state (QWS). It has also been clearly observed that an electron of Cu-O antibonding state is confined within the oxygen covered surface.     

Field-induced expansion deformation in Pb islands on Cu(111): evidence from energy shift of empty quantum-well states

We use scanning tunneling microscopy and spectroscopy to measure the energy shift of empty quantum-well (QW) states in Pb islands on the Cu(111) surface. It is found that, with an increase of the electric field, the behavior of the energy shift can be grouped into two different modes for most QW states. In the first mode, the state energy moves toward high energy monotonically. In the second mode, the state energy shifts to a lower energy initially and then turns around to a higher energy. Moreover, we have observed that the QW states of higher energy behave in preference to the first mode, but they gradually change to the second mode as the Pb island becomes thicker. This thickness-dependent behavior reflects the existence of local expansion in the Pb islands, due to the electric field, and that the expansion is larger for a thicker island. QW states can thus be used for studying the localized lattice deformation in the nanometer scale.     

Effect of strain on the structural and optical properties of Cu-N co-doped ZnO thin films

Polycrystalline ZnO thin films co-doped with Cu and N have been obtained by chemical bath deposition. Introduction of Cu and N causes the change of strained stress in ZnO films, which subsequently affects the structural and optical properties. The dependence of structural and optical properties of the ZnO films on lattice strained stress is investigated by XRD measurement, SEM, PL spectrum, optical reflection and Raman spectrum. The result of photoluminescence of Cu-N co-doped ZnO films indicates that the UV emission peaks shift slightly towards higher energy side with decrease in tensile strain and vise versa. The blue-shift of the absorption edge and up-shift of E2 (high) mode of the films can be observed in the optical reflection and Raman spectra.     

The initial oxidation of Cu(100) single crystal surfaces: an electron spectroscopic investigation

The total energy distribution of electrons emitted from clean Cu(100) and oxygen covered surfaces is analysed. A primary electron energy of 400 eV enabled the investigation of characteristic losses (ELS), Cu MVV Auger transitions and true secondary electrons in a single spectroscopic run. Oxygen exposure up to 10⁸ L at elevated temperature (~400 K) results in a Cu density of states (DOS) strongly affected by O(2p) electrons. The Auger lines of Cu, atomic-like for clean surfaces, reveal DOS effects after some 10⁷ L oxygen exposure: all MVV transitions shift down by ~2 eV in spite of a fixed M₂₃ level; the M₂₃VV Auger line splitting is vanishing due to a broadened valence band maximum allowing the deexcitation of the final two-hole state of intraatomic transitions. Heating the oxygen covered crystal to 820 K is accompanied by the removal of much surface oxygen and an electronic state resembling an earlier oxidation state without DOS effects in the Cu Auger spectrum.     

Tailoring confining barriers for surface states by step decoration: CO /vicinal Cu(111)

The influence of CO adsorption on the Shockley type surface state on vicinal Cu(111) surfaces is investigated using angle resolved photoemission. As the steps are decorated with CO the surface state shifts to higher binding energies, which is opposite to the known behavior on flat Cu(111). This is described within a one-dimensional potential model in which clean steps represent repulsive barriers and decorated steps become attractive wells. From the coverage dependence the integrated CO well potential can be quantified. It is U(CO)a = -2.9 eV A on both Cu(332) and Cu(221) surfaces. Density functional calculations reveal that this attractive potential is due to the very local charge transfer from the Cu step atom to the adsorbed molecule.     

Local spectroscopy of image-potential-derived states: from single molecules to monolayers of benzene on Cu(111)

Stark-shifted image-potential states were measured with an STM tip for benzene adsorbed on a Cu(111) surface. A single benzene molecule locally shifts the position of the first image state toward the Fermi level by 0.2 eV relative to its position on the clean surface. The energetic position of this molecule-modified state shifts to lower energy with increasing coverage of benzene on the surface. This is attributed to local surface potential changes that are correlated with the lowering of the crystal work function due to adsorption of benzene.     

Effects of strain field in nitrogen-mediated Co film growth on Cu(0 0 1): Segregation and electronic structure change

Growth modes of Co thin films on the both N-saturated and partially N-adsorbed Cu(0 0 1) surfaces are studied in detail. From results of the STM and XPS measurements, segregation of N atoms depending on the Co island size is concluded. This new type of atom segregation is explained by means of a lattice strain of the substrate due to the small Co island formation. A novel core-level shift of N 1s during the Co film growth is also reported. A possible influence of the lattice strain to the electronic structure of the surfactant is discussed.     

A study of H2S adsorption kinetics on the clean and oxygen covered (110) surface of copper

The very low pressure adsorption kinetics of H₂S on the clean and oxygen covered Cu(110) face have been examined by Auger Electron Spectroscopy (AES) and Mirror Electron Microscopy (MEM, used for continuous surface potential variations of the copper surface). The AES experimental curves on the clean copper face have been interpreted using a model of island growth by surface diffusion. The presence of an adsorbed oxygen layer on the copper surface changes notably the induction times observed on both AES and MEM measurements.     

Effect of lattice strain on the oxygen vacancy formation and hydrogen adsorption at CeO2(111) surface

Using first-principles calculation, the effect of lattice strain on the oxygen vacancy formation at CeO₂(111) surface has been investigated. The tensile strain facilitates the oxygen vacancy formation at the surface and the compressive strain hinders the process. This is in part due to the strengthening or weakening of the surface Ce–O bond under the lattice strain. On the other hand, a more open surface with a larger lattice constant can better accommodate the larger Ce³⁺ and thus facilitate the structural relaxation of the reduced surface. The studies on the strain effect on the atomic hydrogen adsorption at the defect-free CeO₂(111) surface show that the adsorption strength monotonously increases with the increase of the lattice strain, further confirming the tunable surface chemical activity by lattice strain.     

Sxaps spectra of pyrolytic graphite as a function of the angle of incidence of the incoming electrons

Soft X-ray appearance potential (SXAPS) spectra of pyrolytic graphite as a function of the angle of incidence of the incoming electrons have been measured to obtain information about surface plasmon excitation. Plasmons can be coupled with a core hole and two slow electrons above the Fermi level or with a fast incoming electron. In the last case angular dependent plasmon excitation can be observed. Coupling with the fast incoming electron is observed, but band structure effects cannot be neglected to explain the observed structure. Measurements were performed on clean and hydrogen-contaminated pyrolytic graphite. A signal increase over the whole spectrum was observed after hydrogen contamination, probably due to a rearrangement of the surface lattice structure. Bombardment of the surface with electrons of 2 keV gave a decrease in spectral intensity probably due to surface damage.