On-line preconcentration of trace carcinogenic polycyclic aromatic hydrocarbons (PAHs) in microcolumn liquid chromatography via large volume injection

The ability and efficiency of micro precolumns made of C30 particles, monolithic silica C18 stationary phase and quartz wool coated with C30, which act as novel solid phase absorbing materials, for the on-line enrichment of aqueous polycyclic aromatic hydrocarbons (PAHs) in microcolumn liquid chromatography (LC) was investigated. The enrichment unit was designed in such a way that micro precolumns were directly connected to a 6-port micro injection valve via fused-silica tubing (0.05 mm I.D.) in order to minimize band broadening of the samples, and the enrichment efficiency of the three materials was tested using 14 PAHs, which are selected by the US Environmental Protection Agency (US EPA), as the analytes. The separation of PAHs was evaluated by using laboratory-made C30 or ODS capillary columns and the results were compared. There were no significant differences showed from the separation of PAHs in terms of peak signal between the C30 and ODS capillary columns, but the C30 capillary column was chosen for the following experiment due to its ability to produce better repeatability than the ODS column. By using the three kinds of precolumn materials, results showed that the precolumn packed with C30 particles as well as the capillary monolithic C18 precolumns (0.1 or 0.2 mm I.D.) provided better recovery than those of the quartz wool's. As long as the recovery and separation of the PAHs were concerned, 0.1 mm I.D. monolithic C18 precolumn showed the best results and the R.S.D.s (N = 7) for the retention time, peak area and peak height were between 0.70-1.5, 2.3-5.8 and 2.4-6.6%, respectively. Large volume injection up to 0.5 mL, i.e. 2500-fold enrichment, was possible and no negative effect on the separation profile was found. The LOD (S/N = 3) were between 0.10 and 4.6 pg mL⁻¹, while the LOQ (S/N = 10) were in the range of 0.32-15 pg mL⁻¹, which showed that the system is comparable to many major analytical techniques and is sensitive enough for the trace analysis of PAHs in environmental samples. The system was then applied to the determination of trace PAHs present in soil sample which was randomly taken from a nearby highway.     

A column capacity study of single, serial, and parallel linked rod monolithic high performance liquid chromatography columns

The loading capacity of rod monolithic C18 columns was found to be sensitive to the injection volume, but essentially insensitive to the mass loading for a separation of oligostyrenes. When rod monoliths were coupled in series the injection volume loading increased, as too did the resolution of the oligomers, but at the expense of separation time. The volume load capacity of these serially connected monoliths was, however, not directly proportional to the number of columns connected. The volume load capacity was, however, directly proportional to the number of columns when the monoliths were connected in parallel and the flow stream split between each of the monolithic channels. When the number of monoliths in each channel equaled the number of monoliths that were connected in a single channel serial system the peak capacity and retention time was equivalent for both systems, but the volume load capacity of the parallel system was twice that of the serial connection each time the number of channels doubled. The results of this study indicate that parallel connection of rod monolithic columns may be useful for preparative scale and multidimensional separations where it is important that the volume load capacity is high.     

Simultaneous enrichment and separation of neutral and anionic analytes through combining large volume sample stacking with sweeping in CE

In this work, we overcame the deficiencies of large volume sample stacking (LVSS) in separating low‐mobility and neutral analytes through combining LVSS with sweeping in CE, and employed this new approach to enrich and separate neutral and anionic analytes simultaneously. This technique was carried out with pressure injection of large‐volume sample followed by EOF as a pump pushing the bulk of low‐conductivity sample matrix out of the outlet of the capillary while analytes were swept by micelles and separated via MEKC without the electrode polarity switching. Careful optimization of the enrichment and separation conditions allowed the enrichment factors (EFs) of peak height and peak area of the analytes to be in the range of 9–33 and 21–35 comparing with the conventional injection mode, respectively. The five analytes were baseline separated in 15 min and the detection limits ranged from 26.5 to 55.8 ng/mL (S/N = 3). The developed method was successfully applied to determine adenine, caffeine, theophylline, reduced L‐glutathione (GSH) and oxidized L‐glutathione (GSSG) in two different teas with recoveries that ranged from 84.4 to 105.2%.     

Novel molecularly imprinted monolithic column for selective on-line extraction of ciprofloxacin from human urine

Water-compatible ciprofloxacin-imprinted monolithic columns were synthesized in water-containing systems for selective extraction of ciprofloxacin from human urine samples. Methanol-water (10:3, v/v) was used as a porogenic solvent and the obtained monolithic imprinted polymers reveal high selectivity to ciprofloxacin in an aqueous environment; the affinity can be easily controlled by adjusting the pH of the mobile phase. Owing to the unique porous structure and flow-through channels existing in the network skeleton of the monolithic MIP, urine samples could be directly injected into the column, proteins and other biological matrix were quickly washed out and ciprofloxacin was selectively retained and enriched. Good linearity was obtained from 0.08 to 400 mg/L (r=0.998) with the relative standard deviations less than 3.6%. The limit of detection of the method was 0.04 mg/L and the recoveries were more than 94.5% at three different concentrations. Moreover, by increasing the injection volume to 2.0 mL, the sensitivity of the method could be improved 100-fold according to the peak height of ciprofloxacin. This expedient greatly simplified the overall procedure, resulting in a rapid and efficient sample analysis while maintaining precision and accuracy.     

羰基铁粉掺杂整体柱萃取-在线热解吸进样气相色谱-串联质谱法分析茶叶样品中拟除虫菊酯类农药残留

制备了羰基铁粉掺杂硅胶整体柱，用于拟除虫菊酯类农药残留萃取，并与气相色谱-串联质谱（GC-MS/MS）法联用，建立了在线富集、热解吸GC-MS/MS测定茶叶样品中拟除虫菊酯类农药残留方法。研究将端羟基聚二甲基硅氧烷共价键合到SiO₂网络表面，并同时键合羰基铁粉。将目标分析物吸附并浓缩在聚二甲基硅氧烷位点上后，利用羰基铁粉的高频感应加热特性成功实现了GC-MS/MS直接气体进样并可达到快速、均匀解吸的目的。实验结果表明，在最佳条件下，本方法的富集倍数可达到约1000倍。拟除虫菊酯类农药残留的检出限为3.8~7.5 μg/kg，相对标准偏差为3.2%~6.8%（n=6）。该方法的提取回收率为97.7%~110.5%，相关系数≥0.9960。该法的吸附容量大，在电磁感应的条件下进行热脱附继而直接与GC-MS结合实现在线分析以及无溶剂洗脱。与常规固相微萃取（SPME）方法相比，该方法具有富集因子高、整体柱吸附容量大、可重复使用、自动化程度高、普适性好等优点。在样品前处理及复杂基质中农药残留的提取方面具有重要的研究意义。     

Analysis of phthalates via HPLC-UV in environmental water samples after concentration by solid-phase extraction using ionic liquid mixed hemimicelles

Ionic liquid mixed hemimicelles-based solid-phase extraction for the preconcentration of five phthalates in environmental water sample was investigated in this paper. A comparative study on the use of room temperature ionic liquids (RTILs) 1-hexyl-3-methylimidazolium bromide ([C(6)mim]Br) and 1-dodecyl-3-methylimidazolium bromide ([C(12)mim]Br)-coated silica as sorbents was presented. Owing to having bigger adsorption amounts for analytes [C(12)mim], Br-coated silica was selected as SPE material and the five analytes di-ethyl-phthalate (DEP), di-n-propyl-phthalate (DnPP), di-n-butyl-phthalate (DnBP), di-cyclohexyl-phthalate (DcHP) and di-(2-ethylhexyl)-phthalate (DEHP) can be quantitatively extracted under optimal conditions. The analytes retained on the cartridge were desorbed completely with 3mL methanol (pH 2). Predominant factors influencing the extraction efficiency, such as RTILs concentration, pH value, ionic strength and breakthrough volume were discussed. The proposed method had been applied to determining the five phthalates in four environmental water samples and concentration factor of 600 was achieved easily. Detection limits obtained ranged between 0.12 and 0.17mug/L. The accuracy of this method was evaluated by recovery measurement on spiked samples, and good recovery results (85-107%) with relative standard deviation (R.S.D.) of below 6% were achieved.     

The two-phase amphiphilic preconcentration based on surfactants to enrich phenolic compounds from diluted plant extracts and rat urine by micellar electrokinetic chromatography

A novel technology by two-phase amphiphilic preconcentration based on surfactants was established for enriching phenolic compounds by micellar electrokinetic chromatography (MEKC). The cationic surfactant cetyltrimethylammonium chloride (CTAC) was combined with the anionic analytes that existed in the sample solution before injection. The boundary was formed between CTAC and sodium dodecyl sulfate (SDS) in the background solution when the sample solution was injected into the capillary, where the analytes bound inside micelles were released due to the stronger electrostatic force between SDS and CTAC. This procedure accelerated the separation of analytes from CTAC and greatly improved the enrichment efficiency. The optimal conditions were obtained after a series of optimizations, and the sensitivity enrichment factors of the four analytes were in the range of 39–93 compared to typical injections in capillary zone electrophoresis. Good linearity for matrix-matched calibrations was established for all analytes with R² values of 0.9993–0.9997. The limits of detection (S/N = 3) for kaempferol, quercetin, salvianolic acid C, and salvianolic acid B were 0.0166, 0.0292, 0.0215, and 0.0195 µg/ml, respectively. The intracapillary RSDs of the analytes ranged from 0.8% to 1.3% for migration time and from 0.4% to 1.8% for peak areas. The developed method was successfully applied to the determination of phenolic compounds, the main compounds of Salvia miltiorrhiza Bge., and had been validated for the determination of spiked recoveries in rat urine.     

在线固相萃取-离子色谱法测定4种芳环磺酸盐中的硫酸根离子

建立一种在线固相萃取-离子色谱测定4种芳环磺酸盐中硫酸根离子含量的新方法。将自装填的多孔石墨化碳固相萃取柱应用于离子色谱系统,对样品进行在线前处理。样品经过多孔石墨化碳固相萃取柱基体消除后进入收集环,通过阀切换方式使待测硫酸根离子转入阴离子分析柱和检测系统。固相萃取流路用1.5 mmol/L碳酸钠以0.8 mL/min的流速对基体在线富集,进样量为20μL,分析柱为SH-AC-3(250 mm×4.0 mm)+SH-AG-3(50 mm×4.0 mm)色谱柱,柱温为35℃,在6 mmol/L碳酸钠-4 mmol/L碳酸氢钠条件下等度洗脱,流速为0.8 mL/min。结果表明:硫酸根离子在0.50~20.00 mg/L范围内呈良好的线性关系,线性相关系数为0.998 3,保留时间、峰高和峰面积的相对标准偏差均在0.28%~2.86%之间,方法检出限为0.010 6 mg/L,回收率为91.01%~109.3%,具有良好的线性关系和重复性。整个在线分析过程在25 min之内完成。该方法进样量少、快速、高效。     

On-line concentration of neutral and charged species in capillary electrochromatography with a methacrylate-based monolithic stationary phase

A method involving self-concentration, on-column enrichment and field-amplified sample stacking for on-line concentration in capillary electrochromatography with a polymer monolithic column is presented. Since monolithic columns eliminate the frit fabrication and the problems associated with frits, the experimental conditions could be more flexibly adjusted to obtain higher concentration factor in comparison with conventional particulate packed columns. With self-concentration effect, the detection sensitivity of benzene and hexylbenzene is improved by a factor of 4 and 8, respectively. With on-column enrichment and ultralong injection, improvement as high as 22,000 times in detection sensitivity of benzoin is achieved. Furthermore, a combination of the three above-mentioned methods yields up to a 24,000-fold improvement in detection sensitivity for caffeine, a charged compound. Parameters affecting the efficiency of on-line concentration are investigated systematically. In addition, equations describing on-line concentration process are deduced.     

Online concentration by field-amplified sample injection in acidic buffer for analysis of fangchinoline and tetrandrine in herbal medicine by flow injection-micellar electrokinetic capillary chromatography

A novel, rapid, and continuous online concentration approach based on field-amplified sample injection for the analysis of fangchinoline and tetrandrine was developed in this paper by combination of flow injection-MEKC. The BGE used was a solution composed of 75 mM H3PO4-triethylamine-2.5% v/v polyoxyethylene sorbitan monolaurate-20% v/v methanol buffer (pH* 5.0). The analytes prepared in 50% v/v aqueous ethanol were used as the test analytes. Sample was injected electrokinetically between plugs of water. When the cations reached the boundary between the water plug and BGE, they slowed down and became concentrated. Thereafter, MEKC was initiated for the separation. This results in 6.8-8.9-fold improvement in concentration sensitivity relative to conventional CE methods. The separation could be achieved within 10 min and sample throughput rate can reach up to 50/h. The repeatability (defined as RSD) was 4.8, 4.4% with peak height evaluation and 3.6, 0.94% with peak area evaluation for TET and FAN, respectively.     

Online preconcentration using monoliths in electrochromatography capillary format and microchips

Online preconcentration and separation of analytes using an in situ photopolymerized hexyl acrylate-based monolith stationary phase was evaluated using electrochromatography in capillary format and microchip. The band broadening occurring during the preconcentration process by frontal electrochromatography and during the desorption process by elution electrochromatography was studied. The hexyl acrylate-based monolith provides high retention for neutral analytes allowing the handling of large sample volumes and its structure allows rapid mass transfer, thus reducing the band broadening. For moderately polar analytes such as mono-chlorophenols that are slightly retained in water, it was shown that enrichment factors up to 3500 can be obtained by a hydrodynamic injection of several bed volumes for 120 min under 0.8 MPa with a decrease in efficiency of 50% and a decrease of 30% for the resolution between 2- and 3-chlorophenol. An 8 min preconcentration time allows enrichment factors above 100 for polyaromatic hydrocarbons. The interest of these monoliths when synthesized in microchip is also demonstrated. A 200-fold enrichment was easily obtained for PAHs with only 1 min as preconcentration time, without decrease in efficiency.     

Effect of NaOH on large-volume sample stacking of haloacetic acids in capillary zone electrophoresis with a low-pH buffer

Large-volume sample stacking (LVSS) is an effective on-capillary sample concentration method in capillary zone electrophoresis, which can be applied to the sample in a low-conductivity matrix. NaOH solution is commonly used to back-extract acidic compounds from organic solvent in sample pretreatment. The effect of NaOH as sample matrix on LVSS of haloacetic acids was investigated in this study. It was found that the presence of NaOH in sample did not compromise, but rather help the sample stacking performance if a low pH background electrolyte (BGE) was used. The sensitivity enhancement factor was higher than the case when sample was dissolved in pure water or diluted BGE. Compared with conventional injection (0.4% capillary volume), 97-120-fold sensitivity enhancement in terms of peak height was obtained without deterioration of separation with an injection amount equal to 20% of the capillary volume. This method was applied to determine haloacetic acids in tap water by combination with liquid-liquid extraction and back-extraction into NaOH solution. Limits of detection at sub-ppb levels were obtained for real samples with direct UV detection.     

Analysis of tetrabromobisphenol A and other phenolic compounds in water samples by non-aqueous capillary electrophoresis coupled to photodiode array ultraviolet detection

Non-aqueous capillary electrophoresis (NACE) with large-volume sample stacking injection using the electroosmotic flow pump (LVSEP) has been developed for the determination of tetrabromobisphenol A (TBBPA) and other phenolic compounds in environmental matrices. Methanol has been used as run buffer solvent to reduce the electroosmotic flow (EOF). Identification and quantification of the analytes was performed by photodiode array ultraviolet detection. LVSEP-NACE improved sensitivity of the peak height by 90-300-fold. The method developed was applied to the analysis of TBBPA in river water and wastewater samples, using solid-phase extraction (SPE) as sample pretreatment process. The average recoveries of the analytes were in the range of 96-106% and 73-103% for 1 L of river water and 0.5 L of wastewater samples, respectively. When the method was based on off line SPE-LVSEP-NACE, sensitivity was improved by 3300-4500-fold and 1600-2200-fold for river water and wastewater samples, respectively.     

Affinity monolith preconcentrators for polymer microchip capillary electrophoresis

Developments in biology are increasing demands for rapid, inexpensive, and sensitive biomolecular analysis. In this study, polymer microdevices with monolithic columns and electrophoretic channels were used for biological separations. Glycidyl methacrylate-co-ethylene dimethacrylate monolithic columns were formed within poly(methyl methacrylate) microchannels by in situ photopolymerization. Flow experiments in these columns demonstrated retention and then elution of amino acids under conditions optimized for sample preconcentration. To enhance analyte selectivity, antibodies were immobilized on monoliths, and subsequent lysozyme treatment blocked nonspecific adsorption. The enrichment capability and selectivity of these affinity monoliths were evaluated by purifying fluorescently tagged amino acids from a mixture containing green fluorescent protein (GFP). Twenty-fold enrichment and 91% recovery were achieved for the labeled amino acids, with a >25 000-fold reduction in GFP concentration, as indicated by microchip electrophoresis analysis. These devices should provide a simple, inexpensive, and effective platform for trace analysis in complex biological samples.     

On-line preconcentration of pharmaceutical residues from large volume water samples using short reversed-phase monolithic cartridges coupled to LC-UV-ESI-MS

A simplified preconcentration method for a range of ultra-trace level pharmaceuticals in natural waters has been developed. Solid phase extraction was performed on-line using a micro-reversed-phase monolithic silica column, allowing for very rapid trace enrichment from large volume (500 ml) samples with minimal sample handling. Acceptable recoveries of >70% were obtained for the majority of compounds investigated and the monolithic columns could be washed and conditioned on-line with no sample carryover and used reproducibly for up to eight extractions each. The on-line SPE-LC-UV method was coupled to electrospray ionisation ion trap mass spectrometry (ESI-MS) to increase both selectivity and specificity. Detection limits were determined in spiked river and tap water samples and found to lie in the low ng/l region using sample volumes of 500 ml, loaded at a flow rate of 10 ml/min, and therefore, were suitable for ultra trace analysis.     

Preparation of polypyrrole-coated magnetic particles for micro solid-phase extraction of phthalates in water by gas chromatography-mass spectrometry analysis

In this work, polypyrrole (PPy)-coated Fe(3)O(4) magnetic microsphere were successfully synthesized, and applied as a magnetic sorbent to extract and concentrate phthalates from water samples. The PPy-coated Fe(3)O(4) magnetic microspheres had the advantages of large surface area, convenient and fast separation ability. The PPy coating of magnetic microspheres contributed to preconcentration of phthalates from water sample, due to the π-π bonding between PPy coating and the analytes. Also, the coating could prevent aggregation of the microspheres, and improve their dispersibility. In this study, seven kinds of phthalates were selected as model analytes, including dimethyl phthalate (DMP), diethyl phthalate (DEP), di-iso-butyl phthalate (DIBP), di-n-butyl phthalate (DBP), benzylbutyl phthalate (BBP), di-(2-ethylhexyl) phthalate (DEHP) and di-n-octyl phthalate (DNOP), and gas chromatography-mass spectrometry (GC-MS) was introduced to detect the phthalates after sample pretreatment. Important parameters of the extraction procedure were investigated, and optimized including eluting solvent, the amount of Fe(3)O(4)@PPy particles, and extraction time. After optimization, the procedure took only 15 min to extract and concentrate analytes with high efficiency. Validation experiments showed that the optimized method had good linearity (0.985-0.998), precision (3.4-11.7%), high recovery (91.1-113.4%), and the limits of detection were from 0.006 to 0.068 μg/L. The results indicated that the novel method had advantages of convenience, good sensitivity, high efficiency, and it could also be applied successfully to analyze phthalates in real water sample.     

Chromatographic selectivity of poly(alkyl methacrylate-co-divinylbenzene) monolithic columns for polar aromatic compounds by pressure-driven capillary liquid chromatography

In this study, divinylbenzene (DVB) was used as the cross-linker to prepare alkyl methacrylate (AlMA) monoliths for incorporating π-π interactions between the aromatic analytes and AlMA-DVB monolithic stationary phases in capillary LC analysis. Various AlMA/DVB ratios were investigated to prepare a series of 30% AlMA-DVB monolithic stationary phases in fused-silica capillaries (250-μm i.d.). The physical properties (such as porosity, permeability, and column efficiency) of the synthesized AlMA-DVB monolithic columns were investigated for characterization. Isocratic elution of phenol derivatives was first employed to evaluate the suitability of the prepared AlMA-DVB columns for small molecule separation. The run-to-run (0.16–1.20%, RSD; n = 3) and column-to-column (0.26–2.95%, RSD; n = 3) repeatabilities on retention times were also examined using the selected AlMA-DVB monolithic columns. The π-π interactions between the aromatic ring and the DVB-based stationary phase offered better recognition on polar analytes with aromatic moieties, which resulted in better separation resolution of aromatic analytes on the AlMA-DVB monolithic columns. In order to demonstrate the capability of potential environmental and/or food safety applications, eight phenylurea herbicides with single benzene ring and seven sulfonamide antibiotics with polyaromatic moieties were analyzed using the selected AlMA-DVB monolithic columns.     

Optimization of binary porogen solvent composition for preparation of butyl methacrylate monoliths in capillary liquid chromatography

Butyl methacrylate monolithic columns in 320 microm i.d. fused silica capillaries for reversed-phase capillary liquid chromatography were prepared by radical polymerization initiated thermally with azobisisobutyronitrile (AIBN). Polymerization mixture contained butyl methacrylate (BMA) as the function monomer and ethylene dimethacrylate (EDMA) as the crosslinking agent with 1,4-butanediol and 1-propanol as a binary porogen solvent. Ratio of 1,4-butanediol to 1-propanol in the porogen solvent was optimized regarding the monolithic column efficiency and performance. Total porosity, column permeability, separation impedance, Walters hydrophobicity index, retention factors, peak asymmetry factors, height equivalents to a theoretical plate and peak resolutions were used for characterization of the prepared monolithic columns. The polymerization mixture consisting of 17.8% of BMA, 21.8% of EDMA, 18.0% of 1,4-butanediol, 42.0% of 1-propanol and 0.4% AIBN generated monolithic columns of the best performance having a sufficient permeability and the lowest separation impedance. It was also demonstrated that monolithic columns of this composition exhibited good preparation reproducibility and an excellent pressure resistance when applied in capillary liquid chromatography.     

In-line coupling headspace liquid-phase microextraction with capillary electrophoresis

An analytical technique of in-line coupling headspace liquid-phase microextraction (HS-LPME) with capillary electrophoresis (CE) was proposed to determine volatile analytes. A special cover unit of the sample vial was adopted in the coupling method. To evaluate the proposed method, phenols were used as model analytes. The parameters affecting the extraction efficiency were investigated, including the configuration of acceptor phase, kind and concentration of acceptor solution, extraction temperature and time, salt-out effect, sample volume, etc. The optimal enrichment factors of HS-LPME were obtained with the sample volume of about half of sample vials, which were confirmed by both the theoretical prediction and experimental results. The enrichment factors were obtained from 520 to 1270. The limits of detection (LODs, S/N = 3) were in the range from 0.5 to 1 ng/mL each phenol. The recoveries were from 87.2% to 92.7% and the relative standard deviations (RSDs) were lower than 5.7% (n = 6). The proposed method was successfully applied to the quantitative analysis of the phenols in tap water, and proved to be a simple, convenient and reliable sample preconcentration and determination method for volatile analytes in water samples.     

Nanostructured‐silver‐coated polyetheretherketone tube for online in‐tube solid‐phase microextraction coupled with high‐performance liquid chromatography

Polyetheretherketone tube is a better substrate for in‐tube solid‐phase microextraction than fused‐silica capillary and metal tube because of its resistance to high pressure and good flexibility. It was modified with a nanostructured silver coating, and characterized by scanning electron microscopy and energy dispersive X‐ray spectroscopy. It was connected into high‐performance liquid chromatography equipment to build the online analysis system by replacing the sample loop of a six‐port injection valve. To get the highest extraction capacity, the preparation conditions of the coating was investigated. Important extraction conditions including length of tube, sample volume, and desorption time were optimized using eight polycyclic aromatic hydrocarbons as model analytes. The tube exhibits excellent extraction efficiency toward them, with enrichment factors from 52 to 363. The online analysis method provides good linearity (0.5–100 or 1.0–100 μg/L) and low detection limits (0.15–0.30 μg/L). It has been used to determine polycyclic aromatic hydrocarbons in water samples, with relative recoveries in the range of 92.3–120%. The tube showed highest extraction ability for polycyclic aromatic hydrocarbons, higher extraction ability for hydrophobic phthalates and anilines, and almost no extraction ability for low hydrophobic phenols, due to the possible extraction mechanism including hydrophobic and electron‐rich element‐metal interactions.