A peroxidase-tetrathiafulvalene biosensor based on self-assembled monolayer modified Au electrodes for the flow-injection determination of hydrogen peroxide

The construction and performance under flow-injection conditions of an integrated amperometric biosensor for hydrogen peroxide is reported. The design of the bioelectrode is based on a mercaptopropionic acid (MPA) self-assembled monolayer (SAM) modified gold disk electrode on which horseradish peroxidase (HRP, 24.3 U) was immobilized by cross-linking with glutaraldehyde together with the mediator tetrathiafulvalene (TTF, 1 μmol), which was entrapped in the three-dimensional aggregate formed.

The amperometric biosensor allows the obtention of reproducible flow injection amperometric responses at an applied potential of 0.00 V in 0.05 mol L⁻¹ phosphate buffer, pH 7.0 (flow rate: 1.40 mL min⁻¹, injection volume: 150 μL), with a range of linearity for hydrogen peroxide within the 2.0 × 10⁻⁷–1.0 × 10⁻⁴ mol L⁻¹ concentration range (slope: (2.33 ± 0.02) × 10⁻² A mol⁻¹ L, r = 0.999). A detection limit of 6.9 × 10⁻⁸ mol L⁻¹ was obtained together with a R.S.D. (n = 50) of 2.7% for a hydrogen peroxide concentration level of 5.0 × 10⁻⁵ mol L⁻¹. The immobilization method showed a good reproducibility with a R.S.D. of 5.3% for five different electrodes. Moreover, the useful lifetime of one single biosensor was estimated in 13 days.

The SAM-based biosensor was applied for the determination of hydrogen peroxide in rainwater and in a hair dye. The results obtained were validated by comparison with those obtained with a spectrophotometric reference method. In addition, the recovery of hydrogen peroxide in sterilised milk was tested.     

Flow injection visible diffuse reflectance quantitative analysis of nickel

Flow injection (FI) methodology, using diffuse reflectance in the visible region of the spectrum, for the analysis of nickel, precipitated in the form of dimethylglyoximate, is presented. A reflectance cell, constructed in polytetrafluoroethylene, using a LED (light emitting diode) as light source and a LDR (light dependent resistor) as detector, is described. The analytical signal (S) correlates with nickel concentration (C) between 1.6 × 10⁻⁴ and 6.6 × 10⁻⁴ mol L⁻¹. This correlation is described by the equation S = −1.108 + 3.314 × 10⁴C − 2.081 × 10⁷C² (r = 0.9996). The experimentally observed limit of detection is about 1.3 × 10⁻⁴ mol L⁻¹, as in lower concentrations the formation of precipitate is not observed. The experimental quantitation limit is about 1.6 × 10⁻⁴ mol L⁻¹. The mean R.S.D. (relative standard deviation) is about 2.7%. Samples containing nickel were analyzed and the results obtained in this method were compared with those of other methods using the statistical Student's t-test.     

Determination of folic acid by chemiluminescence based on peroxomonosulfate-cobalt(II) system

Based on the chemiluminescence (CL) phenomena of folic acid in peroxomonosulfate-cobalt(II) system, a rapid and sensitive CL method was developed for determination of folic acid in pharmaceutical preparations and its urinary metabolism processes. Under the optimum conditions, the relative CL intensity was linear over the concentration ranging from 10⁻⁹ to 8 × 10⁻⁷ mol L⁻¹ (R² = 0.9991) with a detection limit as low as 6 × 10⁻¹⁰ mol L⁻¹ (S/N = 3) and relative standard deviation was 2.63% for 2 × 10⁻⁸ mol L⁻¹ folic acid (n = 11). This method has been successfully applied to the determination of folic acid in tablets and human urine. The blank CL emission was yielded owing to the formation of singlet oxygen molecular pair from the quenching experiment of 1,4-diazabicyclo[2.2.2]octane, and pterine-6-carboxylic acid might be the degradation intermediate in this system and it also acts an energy acceptor and sensitizes the chemiluminescence based on the studies of the CL and fluorescence spectra.     

Preparation of a novel fluorescence probe based on covalent immobilization by emulsion polymerization and its application to the determination of metronidazole

A novel method of preparing fluorescence particle probe by emulsion polymerization with covalent immobilization of indicator dye was described. A terminal double bond was attached to 3-amino-9-ethylcarbazole (AEC) via methacryloyl chloride, and the resultant compound was copolymerized with butyl methacrylate. The obtained polymer particles were used as a fluorescence probe, which is almost free of dye leaching, and has higher photostability and lower toxicity in comparison with free AEC. This probe holds great potential for the applications in intracellular measurements. In present study the prepared probe was used for the determination of metronidazole. The results revealed that the probe showed good selectivity and had a linear response to the analyte in the range from 2.0 × 10⁻⁵ to 1.0 × 10⁻³ mol l⁻¹ with a detection limit of 9.0 × 10⁻⁶ mol l⁻¹.     

Square wave adsorptive stripping voltammetric determination of famotidine in urine

Electrochemical studies of famotidine were carried out using voltammetric techniques: cyclic voltammetry, linear sweep and square wave adsorptive stripping voltammetry. The dependence of the current on pH, buffer concentration, nature of the buffer, and scan rate was investigated. The best results for the determination of famotidine were obtained in MOPS buffer solution at pH 6.7. This electroanalytical procedure enabled to determine famotidine in the concentration range 1 × 10⁻⁹–4 × 10⁻⁸ mol L⁻¹ by linear sweep adsorptive stripping voltammetry (LS AdSV) and 5 × 10⁻¹⁰–6 × 10⁻⁸ mol L⁻¹ by square wave adsorptive stripping voltammetry (SW AdSV). Repeatability, precision and accuracy of the developed methods were checked. The detection and quantification limits were found to be 1.8 × 10⁻¹⁰ and 6.2 × 10⁻¹⁰ mol L⁻¹ for LS AdSV and 4.9 × 10⁻¹¹ and 1.6 × 10⁻¹⁰ mol L⁻¹ for SW AdSV, respectively. The method was applied for the determination of famotidine in urine.     

Flow-injection potentiometric determination of triiodide by plasticized poly(vinyl chloride) membrane electrodes and its application to the determination of chlorine-containing disinfectants

Plasticized poly(vinyl chloride) (PVC) membranes of different compositions were tested for use in the construction of potentiometric flow detectors for triiodide. A membrane with a 2:1 (w/w) 2-nitrophenyl octyl ether to PVC ratio was selected. The influence of thiosulphate in the carrier solution composition and of the flow-injection variables on the determination of triiodide was studied. In the selected conditions, a linear relationship between peak height and log[I₃⁻] was obtained between 5 × 10⁻⁶ and 1 × 10⁻⁴ mol l⁻¹ triiodide. Peak height relative standard deviations for 2 × 10⁻⁵ and 1 × 10⁻⁴ mol l⁻¹ triiodide were ±0.4 and ±1.8%, respectively, and sampling frequency was 80 samples per hour. The method proposed was applied satisfactorily to the iodometric determination of different chlorine-containing disinfectants, among them trichloroisocyanuric acid and dichloroisocyanurate in several types of commercial sample.     

Time measurement-visual analysis of nickel(II) using autocatalytic reaction with sodium sulfite/hydrogen peroxide system and its application to the length detection-flow analysis

Trace amounts of nickel(II) can function as a trigger (=reaction initiator) in an autocatalytic reaction with the sodium sulfite/hydrogen peroxide system. Based on this finding, sub-μg L⁻¹ levels of nickel(II) were determined by a time measurement using the autocatalytic reaction. The detection range using the above method was 10⁻⁹–10⁻⁵ M, the detection limit (3σ) was 8.1 × 10⁻¹⁰ M (0.047 μg L⁻¹), and the relative standard deviation was 2.66% at nickel(II) concentration of 10⁻⁷ M (n = 7). This method was applied to length detection-flow injection analysis. The detection range for the flow injection analysis was 2 × 10⁻⁹–2 × 10⁻³ M. The detection limit (3σ) was 1.4 × 10⁻⁹ M (0.082 μg L⁻¹), and the relative standard deviation was 1.86 at initial nickel(II) concentration of 10⁻⁶ M (n = 7).     

Determination of naringin in grapefruit juice by cathodic stripping differential pulse voltammetry at the hanging mercury drop electrode

A highly sensitive cathodic stripping voltammetric method for the determination of naringin is presented. It is based on the formation and accumulation of two naringin–mercury complexes at the electrode surface, followed by reduction of the surface species during a differential pulse voltammetric scan. The cathodic stripping responses at −0.25 V and −0.42 V, are evaluated with respect to various experimental conditions, such as composition and pH of the supporting electrolyte, naringin concentration, accumulation potential and preconcentration time. The new method is suitable for the determination of naringin concentrations between 0.1 mg l⁻¹ (1.72×10⁻⁷ mol l⁻¹) and 40 mg l⁻¹ (6.88×10⁻⁵ mol l⁻¹). A 3σ limit of detection of 32 μg l⁻¹ (55 nmol l⁻¹) can be reached. The relative standard deviation (r.s.d.) is <1.5%. Recovery experiments yielded a mean recovery of 97% (r.s.d.=4.1%). The application of the procedure to the selective determination of naringin in grapefruit juice is demonstrated.     

Enhancement effect of sodium dodecyl benzene sulfonate (SDBS) and its application into voltammetric determination of telmisartan

A sensitive and rapid electrochemical method was developed for the determination of telmisartan based on the enhancement effect of sodium dodecyl benzene sulfonate (SDBS). In 0.1 mol L⁻¹ HClO₄ and in the presence of 7.5 × 10⁻⁵ mol L⁻¹ SDBS, a well-defined and sensitive oxidation peak was observed for telmisartan at the acetylene black (AB) paste electrode. However, the oxidation peak is poor-shaped and the peak current is very low in the absence of SDBS, suggesting that SDBS shows obvious enhancement effect for the determination of telmisartan. After all the experimental parameters were optimized, a sensitive and simple electrochemical method was developed for determining telmisartan. The oxidation peak current is proportional to the concentration of telmisartan over the range from 2.5 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹. The detection limit is 7.5 × 10⁻⁸ mol L⁻¹ after 2 min of accumulation. This new voltammetric method was successfully used to detect telmisartan in drugs.     

Voltammetric determination of glucose based on reduction of copper(II)–glucose complex at lanthanum hydroxide nanowire modified carbon paste electrodes

A novel voltammetric method for the determination of β-d-glucose (GO) is proposed based on the reduction of Cu(II) ion in Cu(II)(NH₃)₄²⁺–GO complex at lanthanum(III) hydroxide nanowires (LNWs) modified carbon paste electrode (LNWs/CPE). In 0.1 mol L⁻¹ NH₃·H₂O–NH₄Cl (pH 9.8) buffer containing 5.0 × 10⁻⁵ mol L⁻¹ Cu(II) ion, the sensitive reduction peak of Cu(II)(NH₃)₄²⁺–GO complex was observed at −0.17 V (versus, SCE), which was mainly ascribed to both the increase of efficient electrode surface and the selective coordination of La(III) in LNW to GO. The increment of peak current obtained by deducting the reduction peak current of the Cu(II) ion from that of the Cu(II)(NH₃)₄²⁺–GO complex was rectilinear with GO concentration in the range of 8.0 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹, with a detection limit of 3.5 × 10⁻⁷ mol L⁻¹. A 500-fold of sucrose and amylam, 100-fold of ascorbic acid, 120-fold of uric acid as well as gluconic acid did not interfere with 1.0 × 10⁻⁵ mol L⁻¹ GO determination.     

Flow-injection determination of acetone with diazotized anthranilic acid through a fluorescent reaction intermediate

Acetone and diazotized anthranilic acid react in alkaline solution, giving a fluorescent intermediate that can be measured at excitation and emission wavelengths of 305 and 395 nm, respectively. Based on this, a fluorimetric flow-injection method is proposed for the determination of acetone in aqueous solution. Under the proposed conditions, acetone can be detected at concentrations higher than 8 × 10⁻⁷ M, with a linear application range from 1 × 10⁻⁶ to 2 × 10⁻⁴ M and an R.S.D. of 2.7% (1.0 × 10⁻⁵ M, n = 10). A sampling frequency of 24 h⁻¹ is achieved. Some potentially interfering species are investigated.     

Determination of fenfluramine based on potassium permanganate-calcein chemiluminescence system

Calcein was found to be able to use as chemiluminescence reagent and post-chemiluminescence was observed when fenfluramine was injected into the mixture after the CL reaction of calcein–potassium permanganate. Based on this phenomenon, a flow injection CL method was established for the determination of fenfluramine. The possible CL mechanism was proposed. The CL intensity was correlated linearly with the concentration of fenfluramine over the range of 1.0 × 10⁻⁷ to 6.0 × 10⁻⁶ g mL⁻¹ and the detection limit was 6 × 10⁻⁸ g mL⁻¹. The relative standard deviation was 2.2% for 5.0 × 10⁻⁷ g mL⁻¹ fenfluramine (n = 11). This method was applied to the determination of fenfluramine in weight-reducing tonic successfully.     

Fluorimetric determination of cyclofenil using photochemical derivatization

In this work, a fluorimetric approach for the determination of cyclofenil, 4-4′-(cyclohexylidenemethylene)bis(phenylacetate), is presented. The method was based on the intense fluorescence (250/410 nm) observed after a UV photochemical treatment of cyclofenil. The influence of the pH and solvent system and UV exposure time on the fluorescence magnitude was studied. Optimization of parameters was made using experimental design (factorial design and central composite design). Limit of detection (3S_b/m) were estimated to be 1.1 × 10⁻⁸ mol L⁻¹ with the linear dynamic range extending up to 8 × 10⁻⁵ mol L⁻¹. This analytical approach was tested through the analysis of a commercial pharmaceutical formulation. In this case, tests enabled an average recovery of 98.3 ± 3.9% (for n = 9) using the analytical curve. The identification of the fluorescent derivative is proposed based on results achieved from GC-MS.     

Repetitive determination of ascorbic acid using iron(III)-1.10-phenanthroline-peroxodisulfate system in a circulatory flow injection method

Ascorbic acid (AA) could be determined in large quantities of a co-existing oxidant. The incorporation of an on-line reagent regeneration step based on redox reaction eliminates the baseline drift in the procedure. This makes it possible to adopt a circulatory flow injection method (cyclic FIA) and to determine AA repetitively. The method is based on the reduction of iron(III) to iron(II) by the analyte, the reaction of the produced iron(II) with 1,10-phenanthroline (phen) in a weak acidic medium to form a colored complex, and the subsequent oxidation reaction of iron(II) to iron(III) by the co-existing peroxodisulfate. A solution (50 ml) of 3.0×10⁻⁴ mol l⁻¹ ferric chloride, 9.0×10⁻⁴ mol l⁻¹ phen and 5.0×10⁻² mol l⁻¹ ammonium peroxodisulfate in acetate buffer (0.2 mol l⁻¹, pH 4.5) is continuously circulated at a constant flow rate of 1.0 ml min⁻¹. Into this stream, an aliquot (20 μl) of the sample solution containing AA is quickly injected by means of a six-way valve. The complex formed is monitored spectrophotometrically (at 510 nm) in the flow system. The stream then returns to the reservoir after passing through a time-delay coil (50 m). The iron(II)–(phen)₃ complex is oxidized to iron(III)–(phen)₃ complex by peroxodisulfate which exists excessively in the circulating reagent solution. The proposed method allows as many as 300 repetitive determinations of 15 mg l⁻¹ AA with only 50 ml reservoir solution. The contents of AA in commercial pharmaceutical products were analyzed to demonstrate the capability of the developed system.     

Determination of potassium ions in biodiesel using a nickel(II) hexacyanoferrate-modified electrode

In this work, nickel hexacyanoferrate-modified electrode was developed to determine potassium ions in biodiesel by potentiometry. The modified electrodes exhibit a linear response to potassium ions in the concentration range of 4.0 × 10⁻⁵ to 1.0 × 10⁻² mol L⁻¹, with a detection limit of 1.9 × 10⁻⁵ mol L⁻¹, and a near-Nernstian slope (53–55 mV per decade) at 25 °C. The method developed in this work was compared with flame photometry and the potassium concentration found in biodiesel showed that the modified electrode method gives results similar to those obtained by flame photometry.     

Electrochemical detection of DNA hybridization using methylene blue and electro-deposited zirconia thin films on gold electrodes

A novel electrochemical DNA biosensor based on methylene blue (MB) and zirconia (ZrO₂) thin films modified gold electrode for DNA hybridization detection is presented. Zirconia thin films were electrodynamically deposited onto the bare gold electrode in an aqueous electrolyte of ZrOCl₂ and KCl by cycling the potential between −1.1 and +0.7 V (versus Ag/AgCl) at a scan rate of 20 mV s⁻¹. Oligonucleotide probes with phosphate group at the 5′ end were attached onto the zirconia thin films because zirconia is affinity for phosphoric group. The surface density of the immobilized DNA molecules at the zirconia interface was investigated by fluorescence spectroscopy method. Hybridization was induced by exposure of the ssDNA-containing Au electrode to complementary ssDNA in solution. The decreases in the peak currents of MB, an electroactive label, were observed upon hybridization of probe with the target. The cathodic peak current (i_p) of MB after hybridization with the target DNA was linearly related to the logarithmic value of the target DNA concentration ranging from 2.25×10⁻¹⁰ to 2.25×10⁻⁸ mol l⁻¹. A detection limit of 1.0×10⁻¹⁰ mol l⁻¹ of oligonucleotides can be estimated.     

Application of lead film electrode for simultaneous adsorptive stripping voltammetric determination of Ni(II) and Co(II) as their nioxime complexes

An adsorptive stripping voltammetric (AdSV) procedure for simultaneous determination of Ni(II) and Co(II) in the presence of nioxime as a complexing agent at an in situ plated lead film electrode was described. The Co(II) signal was enhanced by exploitation of the catalytic process in the presence of nitrite. Ni(II) and Co(II) signals are better separated than in the case of bismuth film electrodes. Calibration graphs for an accumulation time of 120 s are linear from 1 × 10⁻⁹ to 1 × 10⁻⁷ mol L⁻¹ and from 1 × 10⁻¹⁰ to 5 × 10⁻⁹ mol L⁻¹ for Ni(II) and Co(II), respectively. The proposed procedure was applied for Ni(II) and Co(II) determination in water certified reference materials.     

Determination of adenosine disodium triphosphate using prulifloxacin-terbium(III) as a fluorescence probe by spectrofluorimetry

A new spectrofluorimetric method is developed for determination of adenosine disodium triphosphate (ATP). The interactions between prulifloxacin (PUFX)–Tb³⁺ complex and adenosine disodium triphosphate has been studied by using UV–vis absorption and fluorescence spectra. Using prulifloxacin–Tb³⁺ as a fluorescence probe, under the optimum conditions, ATP can remarkably enhance the fluorescence intensity of the prulifloxacin–Tb³⁺ complex at λ = 545 nm and the enhanced fluorescence intensity is in proportion to the concentration of ATP. Optimum conditions for the determination of ATP were also investigated. The dynamic range for the determination of ATP is 4.0 × 10⁻⁷ to 2.0 × 10⁻⁵ mol L⁻¹, and the detection limit (3 σ/k) is 1.7 × 10⁻⁸ mol L⁻¹. This method is simple, practical and relatively free interference from coexisting substances and can be successfully applied to determination of ATP in real pharmaceutical samples. The mechanism of fluorescence enhancement of prulifloxacin–Tb³⁺ complex by ATP was also discussed.     

Kinetic method for the determination of traces of thyroxine by its catalytic effect on the Mn(III) metaphosphate-As(III) reaction

A new, highly sensitive and simple kinetic method for the determination of thyroxine was proposed. The method was based on the catalytic effect of thyroxine on the oxidation of As(III) by Mn(III) metaphosphate. The kinetics of the reaction was studied in the presence of orthophosphoric acid. The reaction rate was followed spectrophotometrically at 516 nm. It was established that orthophosphoric acid increased the reaction rate and that the extent of the non-catalytic reaction was extremely small. A kinetic equation was postulated and the apparent rate constant was calculated. The dependence of the reaction rate on temperature was investigated and the energy of activation and other kinetic parameters were determined.

Thyroxine was determined under the optimal experimental conditions in the range 7.0 × 10⁻⁹ to 3.0 × 10⁻⁸ mol L⁻¹ with a relative standard deviation up to 6.7% and a detection limit of 2.7 × 10⁻⁹ mol L⁻¹. In the presence of 0.08 mol L⁻¹ chloride, the detection limit decreased to 6.6 × 10⁻¹⁰ mol L⁻¹. The proposed method was applied for the determination of thyroxine in tablets. The accuracy of the method was evaluated by comparison with the HPLC method.     

Determination of pentavalent antimony in antileishmaniotic drugs using an automated system for liquid-liquid extraction with on-line detection

An automated system for liquid–liquid extraction flow analysis (LLE-FA) for the determination of Sb(V) in antileishmanial drugs is presented. The method is based on extraction in a 5 mL glass extraction chamber of an ion pair formed between hexachloroantimoniate anion and rhodamine B cation into toluene. The detection system consists of a green light emitting diode (LED) and a photodiode. The system is controlled by a microcomputer using a program written in Visual Basic 3.0. The extraction process was optimized and the following experimental parameters were established: sample loop of 150 μL; reagent loop of 900 μL; stirring time of 100 s; phase separation time of 80 s; volumetric ratio of 1:1 (aqueous/organic). The method was in-house validated for the determination of Sb(V) in meglumine antimoniate. The following performance criteria were obtained: linearity of 0.9989, linear range of 7.0 × 10⁻⁵ to 7.2 × 10⁻⁴ mol Sb(V) L⁻¹, sensitivity of 1.61 × 10⁶ ± 2 arbitrary units L mol⁻¹ (P < 0.05), intra-assay precision of 3.5% (n = 5; 4.1 × 10⁻⁴ mol L⁻¹ Sb(V). Whereas the method is selective in the presence of Sb(III), As(III) and Pb(II) at concentrations up to one tenth of the concentration of Sb(V), As(V) interferes. The accuracy of the method was evaluated through comparison of results obtained from analyses of pharmaceutical formulations by the proposed LLE-FA method with those obtained by inductively coupled plasma optic emission spectrometry (ICP OES) and differential pulse polarography for total antimony and Sb(III), respectively. The proposed method presented an analytical frequency of eight analysis per hour and is suitable for Sb(V) determination in the quality control of drugs employed for the treatment of leishmaniasis.