Silicon Wafers with Facet‐Dependent Electrical Conductivity Properties

By breaking intrinsic Si (100) and (111) wafers to expose sharp {111} and {112} facets, electrical conductivity measurements on single and different silicon crystal faces were performed through contacts with two tungsten probes. While Si {100} and {110} faces are barely conductive at low applied voltages, as expected, the Si {112} surface is highly conductive and Si {111} surface also shows good conductivity. Asymmetrical I –V curves have been recorded for the {111}/{112}, {111}/{110}, and {112}/{110} facet combinations because of different degrees of conduction band bending at these crystal surfaces presenting different barrier heights to current flow. In particular, the {111}/{110} and {112}/{110} facet combinations give I –V curves resembling those of p–n junctions, suggesting a novel field effect transistor design is possible capitalizing on the pronounced facet‐dependent electrical conductivity properties of silicon.     

Synthesis of {100} Facet Dominant Anatase TiO2 Nanobelts and the Origin of Facet‐Dependent Photoreactivity

Sword‐like anatase TiO₂ nanobelts exposed with 78 % clean {100} facets were synthesized and the facet‐dependent photoreactivity of anatase TiO₂ was investigated. By quantitative comparison with the reference {001} facets, the {100} facets possessed about ten‐times higher active sites density than that on {001} facets, resulting in higher photoreaction efficiency. After the active sites density normalization, the {100} and {001} facets exhibited distinct wavelength‐dependent photocatalytic performance, attributed to the anisotropic electronic structures in TiO₂ crystals.     

Platinum Multicubes Prepared by Ni2+‐Mediated Shape Evolution Exhibit High Electrocatalytic Activity for Oxygen Reduction

Pt(100) facets are generally considered less active for the oxygen reduction reaction (ORR). Reported herein is a unique Pt‐branched structure, a multicube, whose surface is mostly enclosed by {100} facets but contains high‐index facets at the small junction area between the adjacent cubic components. The synthesis is accomplished by a Ni²⁺‐mediated facet evolution from high‐index {311} to {100} facets on the frameworks of multipods. Despite the high {100} facet coverage, the Pt multicubes exhibit impressive ORR activity in terms of half‐wave potential and current density nearly to the level of the most active Pt‐based catalysts, while the durability of catalysts is well retained. The facet evolution creates a set of samples with tunable ratios of high‐index to low‐index facets. The results reveal that the excellent ORR performance of Pt multicubes is a combined result of active sites by high‐index facets and low resistance by flat surface. It is anticipated that this work will offer a new approach to facet‐controlled synthesis and ORR catalysts design.     

The Effects of Exposed Specific Facets and Sulfation on the Surface Acidity of Cu2O Solids

Cuprous oxide microcrystals with {111}, {111}/{100}, and {100} exposed facets were synthesized. ³¹P MAS NMR using trimethylphosphine as the probe molecule was employed to study the acidic properties of samples. It was found that the total acidic density of samples increases evidently after sulfation compared with the pristine cuprous oxide microcrystals. During sulfation, new {100} facets are formed at the expense of {111} facets and lead to the generation of two Lewis acid sites due to the different binding states of SO₄²⁻ on {111} and {100} facets. Moreover, DFT calculation was used to illustrate the binding models of SO₄²⁻ on {111} and {100} facets. Also, a Pechmann condensation reaction was applied to study the acidic catalytic activity of these samples. It was found that the sulfated {111} facet has better activity due to its higher Lewis acid density compared with the sulfated {100} facet.     

Crystal‐Facet Engineering of Ferric Giniite by Using Ionic‐Liquid Precursors and Their Enhanced Photocatalytic Performances under Visible‐Light Irradiation

In the work presented here, well‐dispersed ferric giniite microcrystals with controlled sizes and shapes are solvothermally synthesized from ionic‐liquid precursors by using 1‐n‐butyl‐3‐methylimidazolium dihydrogenphosphate ([Bmim][H₂PO₄]) as phosphate source. The success of this synthesis relies on the concentration and composition of the ionic‐liquid precursors. By adjusting the molar ratios of Fe(NO₃)₃ ? 9H₂O to [Bmim][H₂PO₄] as well as the composition of ionic‐liquid precursors, we obtained uniform microstructures such as bipyramids exposing {111} facets, plates exposing {001} facets, hollow spheres, tetragonal hexadecahedron exposing {441} and {111} facets, and truncated bipyamids with carved {001} facets. The crystalline structure of the ferric giniite microcrystals is disclosed by various characterization techniques. It was revealed that [Bmim][H₂PO₄] played an important role in stabilizing the {111} facets of ferric giniite crystals, leading to the different morphologies in the presence of ionic‐liquid precursors with different compositions. Furthermore, since these ferric giniite crystals were characterized by different facets, they could serve as model Fenton‐like catalysts to uncover the correlation between the surface and the catalytic performance for the photodegradation of organic dyes under visible‐light irradiation. Our measurements indicate that the photocatalytic activity of as‐prepared Fenton‐like catalysts is highly dependent on the exposed facets, and the surface area has essentially no obvious effect on the photocatalytic degradation of organic dyes in the present study. It is highly expected that these findings are useful in understanding the photocatalytic activity of Fenton‐like catalysts with different morphologies, and suggest a promising new strategy for crystal‐facet engineering of photocatalysts for wastewater treatment based on heterogeneous Fenton‐like process.     

α‐Fe2O3 Polyhedral Nanoparticles Enclosed by Different Crystal Facets: Tunable Synthesis,Formation Mechanism Analysis,and Facets‐dependent n‐Butanol Sensing Properties

Three kinds of polyhedral α‐Fe₂O₃ nanoparticles enclosed by different facets including oblique parallel hexahedrons (op‐hexahedral NPs), cracked oblique parallel hexahedrons (cop‐hexahedral NPs), and octadecahedral nanoparticles (octadecahedral NPs), were successfully prepared by simply changing only one reaction parameter in the hydrothermal process. The structural and morphological of the products were systematically studied using various characterizations including X‐ray diffraction (XRD), scanning electron microscopy (SEM), and transmission electron microscopy (TEM), revealing that the three kinds of α‐Fe₂O₃ nanoparticles were enclosed by {104}, {110}/{104}, and {102}/{012}/{104} crystal planes, respectively. The exposed facets and shape of the nanocrystals were found to be affected by the adding amount of ethylene glycol in the solvent. The gas‐sensing properties and mechanism of the α‐Fe₂O₃ samples were studied and analyzed, which indicated that the sensitivity of the three samples followed the order of octadecahedral NPs > cop‐hexahedral NPs > op‐hexahedral NPs due to the combined effects of specific surface area and oxygen defects in the nanocrystals.     

Enhancing the Photocatalytic Activity of Anatase TiO2 by Improving the Specific Facet‐Induced Spontaneous Separation of Photogenerated Electrons and Holes

Recently, it has been proven that directional flow of photogenerated charge carriers occurs on specific facets of TiO₂ nanocrystals. Herein, we demonstrate that the photocatalytic activity of anatase TiO₂ nanocrystals in both photoreduction and photooxidation processes can be enhanced by selectively depositing Pt nanoparticles on the {101} facets, which strengthens spontaneously surface‐induced separation between photogenerated electrons and holes in the photocatalysis process. An optimal ratio of the oxidative {001} facets to the reductive {101} facets exists with regard to the photocatalysis of the faceted TiO₂ nanocrystals, and this is crucial for balancing the recombination and redox reaction rates of photogenerated electrons and holes. The present work might help us gain deeper insight into the relation between the specific surface of semiconductor photocatalysts and their photocatalytic activities and provides us with a new route to design photocatalysts with high photocatalytic activity.     

Visible‐Light‐Induced Efficient Selective Oxidation of Nonactivated Alcohols over {001}‐Faceted TiO2 with Molecular Oxygen

In the presence of molecular oxygen, a {001}‐faceted nanocrystalline anatase TiO₂ catalyst enabled the selective oxidation of nonactivated aliphatic alcohols to the corresponding aldehydes or ketones under visible light. The reaction shows excellent conversion and selectivity towards the formation of the carbonyl products without over‐oxidation to the corresponding carboxylic acids. The exceptional reactivity of the catalyst is possibly due to the absorption of visible light originating from a stronger interaction of alcohol with the {001} facet, which facilitates the modification of the band structure of TiO₂, thus facilitating the photogenerated hole transfer and subsequent oxidation processes. The experimental results have also been corroborated by first‐principles quantum chemical DFT calculations.     

Prolonging charge-separation states by doping lanthanide-ions into {001}/{101} facets-coexposed TiO2 nanosheets for enhancing photocatalytic H2 evolution

Ultrathin TiO₂ nanosheets with coexposed {001}/{101} facets have attracted considerable attention because of their high photocatalytic activity. However, the charge-separated states in the TiO₂ nanosheets must be extended to further enhance their photocatalytic activity for H₂ evolution. Herein, we present a successful attempt to selectively dope lanthanide ions into the {101} facets of ultrathin TiO₂ nanosheets with coexposed {001}/{101} facets through a facile one-step solvothermal method. The lanthanide doping slightly extended the light-harvesting region and markedly improved the charge-separated states of the TiO₂ nanosheets as evidenced by UV-vis absorption and steady-state/transient photoluminescence spectra. Upon simulated sunlight irradiation, we observed a 4.2-fold enhancement in the photocatalytic H₂ evolution activity of optimal Yb³⁺-doped TiO₂ nanosheets compared to that of their undoped counterparts. Furthermore, when Pt nanoparticles were used as cocatalysts to reduce the H₂ overpotential in this system, the photocatalytic activity enhancement factor increased to 8.5. By combining these results with those of control experiments, we confirmed that the extended charge-separated states play the main role in the enhancement of the photocatalytic H₂ evolution activity of lanthanide-doped TiO₂ nanosheets with coexposed {001}/{101} facets.     

Facet‐Dependent Electrical Conductivity Properties of Silver Oxide Crystals

Ag₂O cubes, truncated octahedra, rhombic dodecahedra, and rhombicuboctahedra were synthesized in aqueous solution. Two tungsten probes were brought into contact with a single particle for electrical conductivity measurements. Strongly facet‐dependent electrical conductivity behaviors have been observed. The {111} faces are most conductive. The {100} faces are moderately conductive. The {110} faces are nearly non‐conductive. When electrodes contacted two different facets of a rhombicuboctahedron, asymmetrical I–V curves were obtained. The {111} and {110} combination gives the best I–V curve expected for a p‐n junction with current flowing in one direction through the crystal but not in the opposite direction. Density of states (DOS) plots for varying number of different lattice planes of Ag₂O match with the experimental results, suggesting that the {111} faces are most electrically conductive. The thicknesses of the thin surface layer responsible for the facet‐dependent properties of Ag₂O crystals have been determined.     

Direct Imaging of Highly Anisotropic Photogenerated Charge Separations on Different Facets of a Single BiVO4 Photocatalyst

Spatially resolved surface photovoltage spectroscopy (SRSPS) was employed to obtain direct evidence for highly anisotropic photogenerated charge separation on different facets of a single BiVO₄ photocatalyst. Through the controlled synthesis of a single crystal with preferentially exposed {010} facets, highly anisotropic photogenerated hole transfer to the {011} facet of single BiVO₄ crystals was observed. The surface photovoltage signal intensity on the {011} facet was 70 times stronger than that on the {010} facets. The influence of the built‐in electric field in the space charge region of different facets on the anisotropic photoinduced charge transfer in a single semiconductor crystal is revealed.     

Atomic‐Scale Determination of Active Facets on the MoVTeNb Oxide M1 Phase and Their Intrinsic Catalytic Activity for Ethane Oxidative Dehydrogenation

Aberration‐corrected high‐angle annular dark‐field scanning transmission electron microscopy (HAADF‐STEM) has been used to image the basal {001} plane of the catalytically relevant M1 phase in MoVTeNb complex oxides. Facets {010}, {120}, and {210} are identified as the most frequent lateral termination planes of the crystals. Combination of STEM with He ion microscopy (HIM) images, Rietveld analysis, and kinetic tests reveals that the activation of ethane is correlated to the availability of facets {001}, {120}, and {210} at the surface of M1 crystals. The lateral facets {120} and {210} expose crystalline positions related to the typical active centers described for propane oxidation. Conversely, the low activity of the facet {010} is attributed to its configuration, consisting of only stable M₆O₂₁ units connected by a single octahedron. Thus, we quantitatively demonstrated that differences in catalytic activity among M1 samples of equal chemical composition depend primarily on the morphology of the particles, which determines the predominant terminating facets.     

Facet Engineering on WO3 Mono-Particle-Layer Electrode for Photoelectrochemical Water Splitting

Photoelectrochemical (PEC) performance of WO₃ photoanodes for water splitting is heavily influenced by the orientation of crystal facets. In this work, mono-particle-layer electrodes, assembled by particulate WO₃ square plates with highly uniform alignment along the (002) facet, improved PEC water oxidation kinetics and stability. Photo-deposition of Au along the cracks formed on the surface of the plates, which are the edges of {110} facets, was found to further enhance electron collection efficiency. Combination of these two strategies allowed the facet-engineered WO₃ electrode to produce significantly higher efficiencies in charge separation and transfer than the electrode prepared without facet orientation. This work has provided a facile route for fabricating a structurally designed WO₃ photoelectrode, which is also applicable to other regularly shaped semiconductor photocatalysts with anisotropic charge migration.     

Template‐Free Synthesis of Core–Shell TiO2 Microspheres Covered with High‐Energy {116}‐Facet‐Exposed N‐Doped Nanosheets and Enhanced Photocatalytic Activity under Visible Light

Core–shell TiO₂ microspheres possess a unique structure and interesting properties, and therefore, they have received much attention. The high‐energy facets of TiO₂ also are being widely studied for the high photocatalytic activities they are associated with. However, the synthesis of the core–shell structure is difficult to achieve and requires multiple‐steps and/or is expensive. Hydrofluoric acid (HF), which is highly corrosive, is usually used in the controlling high‐energy facet production. Therefore, it is still a significant challenge to develop low‐temperature, template‐free, shape‐controlled, and relative green self‐assembly routes for the formation of core–shell‐structured TiO₂ microspheres with high‐energy facets. Here, we report a template‐ and hydrofluoric acid free solvothermal self‐assembly approach to synthesize core–shell TiO₂ microspheres covered with high‐energy {116}‐facet‐exposed nanosheets, an approach in which 1,4‐butanediamine plays a key role in the formation of nanosheets with exposed {116} facets and the doping of nitrogen in situ. In the structure, nanoparticle aggregates and nanosheets with {116} high‐energy facets exposed act as core and shell, respectively. The photocatalytic activity for degradation of 2,4,6‐tribromophenol and Rhodamine B under visible irradiation and UV/Vis irradiation has been examined, and improved photocatalytic activity under visible light owing to the hierarchical core–shell structure, {116}‐plane‐oriented nanosheets, in situ N doping, and large surface areas has been found.     

The Origin of Shape Sensitivity in Palladium‐Catalyzed Suzuki–Miyaura Cross Coupling Reactions

The shape sensitivity of Pd catalysts in Suzuki–Miyaura coupling reactions is studied using nanocrystals enclosed by well‐defined surface facets. The catalytic performance of Pd nanocrystals with cubic, cuboctahedral and octahedral morphologies are compared. Superior catalytic reactivity is observed for Pd NCs with {100} surface facets compared to {111} facets. The origin of the enhanced reactivity associated with a cubic morphology is related to the leaching susceptibility of the nanocrystals. Molecular oxygen plays a key role in facilitating the leaching of Pd atoms from the surface of the nanocrystals. The interaction of O₂ with Pd is itself facet‐dependent, which in turn gives rise to more efficient leaching from {100} facets, compared to {111} facets under the reaction conditions.     

{111}晶面暴露对介孔金红石TiO2单晶光催化产氢的促进作用

光催化反应发生在半导体材料的表面,材料表面的原子/电子结构直接影响光催化剂的活性或选择性。因此,发展具有特定晶面的半导体光催化剂受到各国学者的普遍关注,被认为是调控光催化材料性能的有效途径之一。自2008年yang等首次合成高表面能{001}晶面占优的锐钛矿TiO2单晶以来,控制合成暴露不同晶面TiO2晶体的研究得到了迅猛的发展,已发展了多种方法合成了具有不同晶面的TiO2晶体。研究表明,选择性地暴露特定的活性晶面能够显著地提高光催化剂的活性或者改变光催化反应的选择性。但是,含有完整晶面构型的TiO2单晶样品的颗粒尺寸一般都较大,通常为几微米,因而显著增加了光生载流子传输与分离的难度,并且导致材料较小的比表面积,限制了对光催化活性的进一步提高。能否在合成含特定晶面单晶的同时增加多孔结构成为有效解决这一问题的关键。最近, Crossland等采用晶种模板法成功合成了介孔的锐钛矿TiO2单晶,并且通过光电器件研究证实了采用该思路可进一步提高材料的光电性能。金红石TiO2在光催化全分解水方面具有独特的优势,然而关于多孔单晶金红石TiO2的研究相对较少,尤其是合成热力学不稳定的高表面能{111}晶面完全暴露的多孔金红石单晶面临较大的技术挑战因而一直未见文献报道。本文利用晶种模板法,以TiCl4溶液为含Ti前驱体、NaF为形貌控制剂、采用水热处理制备出不同比例{111}晶面的介孔金红石单晶。我们前期工作表明, NaF可作为形貌控制剂合成低表面能{110)晶面占优的介孔金红石单晶。本文发现,通过改变NaF的添加量,可有效调变{111}/{110}晶面比例,最终合成完全暴露{111}高表面能的介孔金红石TiO2单晶。扫描电镜结果显示,当添加20 mg NaF时,合成{110}占优的具有高长径比的介孔晶体;当NaF用量增加到40 mg时{110}晶面进一步缩短;至80 mg时则制备出{111})高能面完全暴露的金红石TiO2晶体。值得注意的是,对比研究表明,不采用模板合成了与多孔晶体完全相对应的不同{111}/(110}晶面比例的实心金红石晶体。透射电镜及选区电子衍射以及结合X射线衍射进一步证实,多孔的金红石TiO2晶体与实心金红石单晶均都为单晶结构,孔结构贯穿于样品内部且具有较高的晶面结晶性。氮气吸附实验发现,虽然三个不同晶面比例介孔金红石单晶样品间的形貌具有显著的差异,但比表面积非常相近(分别为24,25,28 m2/g),孔径也都为50 nm左右,该值与所用SiO2模板球的直径以及TEM观察结果相一致。光催化产氢性能结果表明,选择性的暴露活性晶面显著提高了光催化活性,仅含高能面{111}的介孔金红石单晶样品具有最高的产氢速率(约800μmol h–1 g–1),比常规{110}晶面占优的介孔单晶样品速率提高了约一倍。尤其比实心单晶样品的产氢速率提高了至少一个数量级,这应归结于介孔结构特性所导致的表面反应活性位增加、电子传输距离缩短以及光吸收增强协同作用的结果。     

Facet‐Dependent Catalytic Activity of Cu2O Nanocrystals in the One‐Pot Synthesis of 1,2,3‐Triazoles by Multicomponent Click Reactions

We report the highly facet‐dependent catalytic activity of Cu₂O nanocubes, octahedra, and rhombic dodecahedra for the multicomponent direct synthesis of 1,2,3‐triazoles from the reaction of alkynes, organic halides, and NaN₃. The catalytic activities of clean surfactant‐removed Cu₂O nanocrystals with the same total surface area were compared. Rhombic dodecahedral Cu₂O nanocrystals bounded by {110} facets were much more catalytically active than Cu₂O octahedra exposing {111} facets, whereas Cu₂O nanocubes displayed the slowest catalytic activity. The superior catalytic activity of Cu₂O rhombic dodecahedra is attributed to the fully exposed surface Cu atoms on the {110} facet. A large series of 1,4‐disubstituted 1,2,3‐triazoles have been synthesized in excellent yields with high regioselectivity under green conditions by using these rhombic dodecahedral Cu₂O catalysts, including the synthesis of rufinamide, an antiepileptic drug, demonstrating the potential of these nanocrystals as promising heterogeneous catalysts for other important coupling reactions.     

Visible Light-Driven Conversion of Carbon-Sequestrated Seawater into Stoichiometric CO and HClO with Nitrogen-Doped BiOCl Atomic Layers

Seawater is one of the most important CO₂ sequestration media for delivering value-added chemicals/fuels and active chlorine; however, this scenario is plagued by sluggish reaction rates and poor product selectivity. Herein, we first report the synthesis of nitrogen-doped BiOCl atomic layers to directly split carbon-sequestrated natural seawater (Yellow Sea, China) into stoichiometric CO (92.8 μmol h⁻¹) and HClO (83.2 μmol h⁻¹) under visible light with selectivities greater than 90 %. Photoelectrons enriched on the exposed BiOCl{001} facet kinetically facilitate CO₂-to-CO reduction via surface-doped nitrogen bearing Lewis basicity. Photoholes, mainly located on the lateral facets of van der Waals gaps, promote the selective oxidation of Cl⁻ into HClO. Sequestrated CO₂ also maintains the pH of seawater at around 4.2 to prevent the alkaline earth cations from precipitating. The produced HClO can effectively kill typical bacteria in the ballast water of ocean-going cargo ships, offering a green and safe way for onsite sterilization.     

The Active Sites of a Rod‐Shaped Hollandite DeNOx Catalyst

The identification of catalytically active sites (CASs) in heterogeneous catalysis is of vital importance to design and develop improved catalysts, but remains a great challenge. The CASs have been identified in the low‐temperature selective catalytic reduction of nitrogen oxides by ammonia (SCR) over a hollandite manganese oxide (HMO) catalyst with a rod‐shaped morphology and one‐dimensional tunnels. Electron microscopy and synchrotron X‐ray diffraction determine the surface and crystal structures of the one‐dimensional HMO rods closed by {100} side facets and {001} top facets. A combination of X‐ray absorption spectra, molecular probes with potassium and nitric oxide, and catalytic tests reveals that the CASs are located on the {100} side facets of the HMO rods rather than on the top facets or in the tunnels, and hence semi‐tunnel structural motifs on the {100} facets are evidenced to be the CASs of the SCR reaction. This work paves the way to further investigate the intrinsic mechanisms of SCR reactions.     

具有主导晶面的BiOIO3/BiOCl异质结制备与光催化性能

分别以乙二醇/去离子水为溶剂,通过溶剂热/水热法分别制备了具有不同主导晶面的BiOIO₃/{110}BiOCl和BiOIO₃/{001}BiOCl异质结。采用X射线衍射、扫描电子显微镜、能量色散谱和紫外可见漫反射光谱对制备的BiOIO₃/BiOCl光催化剂进行了表征。在可见光照射下,通过对罗丹明 B和苯酚水溶液的光催化降解,考察了 BiOIO₃/BiOCl异质结的光催化活性。结果显示25% BiOIO₃/{110}BiOCl异质结具有最高的光催化效率。BiOIO₃/{110}BiOCl较好的光催化性能是由于其在可见光区较强的光吸收,以及异质结结构和BiOCl所具有的(110)主导晶面有利于光生载流子的分离。超氧自由基(·O₂^-)和空穴(h⁺)是光催化过程中的主要活性物质。此外,根据实验结果探讨了光催化性能增强的机理。