Reverse hydrophobic PDMS surface to hydrophilic by 1‐step hydrolysis reaction

Hydrophilic modification on the surface of polymer polydimethylsiloxane (PDMS) material is a key step for its application in biomaterial, bioengineering, and so on. In this article, a novel and effective method was proposed to reverse hydrophobic surface to hydrophilic by 1‐step hydrolysis of Si―O bond to produce hydrophilic hydroxyl group. The hydrophilizing reagent 2‐(trimethylsiloxy) ethyl methacrylate (TMSEMA) was used during the copolymerization of polydimethylsiloxane prepolymer (DMS U21). The prepared PDMS film was subjected to 1‐step surface hydrophilic reversal treatment using KOH solution to produce hydroxyl groups on the surface. The contact angle, attenuated total reflection Fourier transform infrared spectra, and equilibrium water content (EWC) measurements were conducted on PDMS films. The results showed that TMSEMA content had no obvious impact on the contact angle and EWC value of untreated PDMS. After reversal treatment, the contact angle decreased from 94° to 15°, and the EWC value increases to 10% when the TMSEMA content was 15 wt%. The spectrum proved that the reverse reaction produced hydroxyl and carboxylate on the surface. The hydrophilic stability, surface morphology, and protein adsorption properties of PDMS film were also investigated. This study can provide new ideas and further reference for improving the hydrophilicity of PDMS surface.     

Effects of peak anomalies with the hydrophilic or hydrophobic properties of reservoirs during serial injection on a capillary electrophoresis microchip

Several anomalies, e.g., in peak shape, migration time, and baseline drift, all due to pressure-driven backflow, were previously reported to occur during serial injection on capillary electrophoresis (CE) chips. Since these anomalies were worse for polydimethylsiloxane (PDMS) microchips than for glass microchips, reproducible data on PDMS microchips were difficult to obtain. In this paper, we found that these problems were affected by the hydrophilic or hydrophobic properties of the reservoirs on the microchip and demonstrated that these anomalies were reduced by converting the hydrophobic properties of the reservoirs on the PDMS microchip into hydrophilic ones. Thus, compared with hydrophobic reservoirs, hydrophilic reservoirs were suitable for the formation of a stable plug. Several chip designs were suggested to reduce these pressure-driven backflows.     

Synthesis and characterization of biodegradable hydrophobic–hydrophilic hydrogel networks with a controlled swelling property

A biodegradable polymer network hydrogel system with both hydrophilic and hydrophobic components was synthesized and characterized. The hydrophilic and hydrophobic components were dextran and poly(D,L )lactic acid (PDLLA), respectively. These two polymers were chemically modified for incorporating unsaturated groups for subsequent UV crosslinking to generate a hydrogel with a three‐dimensional network structure. The effects of the reaction conditions on the synthesis of a dextran derivative of allyl isocyanate (dex‐AI) were studied. All newly synthesized materials were characterized by Fourier transform infrared and NMR. The swelling property of the hydrogels was studied in buffer solutions of different pHs. The results of this study showed that a wide‐range swelling property was obtained by changes in the dex‐AI/PDLLA composition ratio, the type and degree of unsaturated groups incorporated into dextran, and the UV photocrosslinking time. The solvent extraction effect on the swelling property of the hydrogels was also studied. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 2392–2404, 2000     

PVA networks grafted with PDMS branches

We describe a simple and efficient synthesis of poly(vinyl alcohol) (PVA) networks fitted with polydimethylsiloxane (PDMS) branches (PVA_netw‐g‐PDMS). The syntheses were achieved in two steps: (1) Grafting by urethane linking PDMS carrying ? NCO termini (PDMS‐NCO) onto PVA fitted with a few (～4) photoreactive acryl amide groups (PVA_AA), followed by (2) Photocrosslinking the PVA_AA‐g‐PDMS to PVA_netw‐g‐PDMS. The use of the binary N‐methyl‐2‐pyrrolidone/tetrahydrofuran (NMP/THF, 67/33) solvent system enabled the thermodynamically unfavorable mixing of hydrophobic PDMS branches with hydrophilic PVA_AA backbones. The amphiphilic graft, PVA_AA‐g‐PDMS, was characterized by ¹H NMR spectroscopy, and the final graft network, PVA_netw‐g‐PDMS, by FTIR spectroscopy, DSC, and equilibrium swelling. The grafting of sufficient volumes of PDMS branches onto PVA_AA yields cocontinuous hydrophilic/hydrophobic PVA/PDMS domains, whose existence was demonstrated by swelling in both water and hexanes. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5272–5277, 2009     

Synthesis and characterization of biodegradable network hydrogels having both hydrophobic and hydrophilic components with controlled swelling behavior

A new class of biodegradable hydrogels, consisting of hydrophobic poly(D ,L )lactic acid (PDLLA) and hydrophilic dextran segments with a polymer network structure, was synthesized with UV photopolymerization. Unsaturated vinyl groups first were introduced onto the PDLLA and dextran polymer backbones, then followed by a crosslinking reaction of diacrylate-terminated PDLLA and dextran acrylate. The chemical crosslinking forced the hydrophobic PDLLA and hydrophilic dextran segments to mix with each other in the network hydrogels. The new polymers were characterized by standard polymer characterization methods such as NMR, Fourier transform infrared spectroscopy, and gel permeation chromatography. The effects of reaction time, temperature, and molar ratio of the reactants on the incorporation of acrylate onto the polymer backbone were examined. A series of hydrogels with different dextran/PDLLA composition ratios was prepared, and their swelling behaviors were studied. These new bicomponent network hydrogels had a wide range of hydrophilicity to hydrophobicity that was difficult to achieve in totally hydrophilic hydrogels. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 4554–4569, 1999     

Stable modification of PDMS surface properties by plasma polymerization: application to the formation of double emulsions in microfluidic systems

We describe a method based on plasma polymerization for the modification and control of the surface properties of poly(dimethylsiloxane) (PDMS) surfaces. By depositing plasma polymerized acrylic acid coatings on PDMS, we succeeded to fabricate stable (several days) hydrophilic and patterned hydrophobic/hydrophilic surfaces. We used this approach to generate direct and (for the first time in this material) double emulsions in PDMS microchannels.     

Amphiphilic membranes crosslinked and reinforced by POSS

This article concerns the synthesis and characterization of novel tricomponent amphiphilic membranes consisting of hydrophilic poly(ethylene glycol) (PEG) and hydrophobic polydimethylsiloxane (PDMS) segments cocrosslinked and reinforced by octasilane polyhedral oligomeric silsesquioxane (octasilane‐POSS) cages. Rapid and efficient network synthesis was effected by cocrosslinking diallyl‐telechelic PEG (A‐PEG‐A) and divinyl‐telechelic PDMS (V‐PDMS‐V) with pentamethylpentacyclosiloxane (D₅H), using Karstedt's catalyst in conjunction with Et₃N cocatalyst and water. Films were prepared by pouring charges in molds and crosslinking by heating at 60 °C for several hours. The films were characterized by sol fractions and equilibrium swelling both in hexane and water, extent of crosslinking, contact angle hysteresis, oxygen permeability, thermogravimetric analysis, and mechanical properties. The crosslinking of octasilane‐POSS achieved by the same catalyst system was studied in separate experiments. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4337–4352, 2004     

Specific properties of in situ ruthenium‐catalyzed polyamide 12/polydimethylsiloxane compatibilized blend

The main objective of this work focused on the chemical modification of polyamide 12 (PA12) properties through the reaction with a hydride‐terminated polydimethylsiloxane (PDMS‐SiH). The investigated PA12/PDMS‐SiH blend was compatibilized by ruthenium derivative catalyzed hydrosilylation reaction in molten state. This original route enhanced interfacial adhesion and avoid PDMS‐SiH leaching phenomenon between the two immiscible phases. More specifically, the size of PDMS‐SiH domains in the blend decreased from around 4 μm to 800 nm and from 30 to 1 μm after compatibilization with 10 and 20 wt % PDMS‐SiH, respectively. For the best compatibilized PA12/PDMS‐SiH blend, the introduction of PDMS lowered the surface free energy and the PA12‐based blend turned from hydrophilic to hydrophobic behavior, as evidenced by the water contact angle measurements. Gas permeability and CO₂/H₂ and CO₂/He gas selectivity were also improved with the increase in PDMS content. Besides, the mechanical properties were enhanced with 13% increase in Young's modulus after in situ compatibilization with 15 wt % PDMS‐SiH. Thermal stability was also improved after compatibilization as the initial degradation temperature of reactive blends obviously increased compared with nonreactive ones. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2018 , 56, 978–988     

Impact properties,phase structure,compatibility, and fracture morphology of polyamide‐1010/thermoplastic poly(ester urethane) elastomer blends

Blends of polyamide‐1010 (PA1010) and a thermoplastic poly(ester urethane) elastomer (TPU) were prepared by melt extrusion. The impact properties, phase structure, compatibility, and fracture morphology under impact were investigated for PA1010/TPU blends. The results indicated that TPU enhanced the impact strength of PA1010, and the best impact modification effect of the blends was obtained with 20 wt % TPU. The phase structure was investigated with scanning electron microscopy, and the compatibility was investigated with dynamic mechanical analysis and small‐angle X‐ray scattering. The study of the fracture morphology of PA1010/TPU blends indicated that the fracture surface of the blends had special features, consisting of many fibrillar elastomer particles and a conglutination–multilayer structure, as well as many small tubers on this structure. These fracture phenomena could not be found on the fracture surface of pure PA1010. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1177–1185, 2005     

Nonwettable thin films from hybrid polymer brushes can be hydrophilic

Hybrid brushes composed of two liquid polymers, poly(dimethylsiloxane) (PDMS) and a highly branched ethoxylated polyethylenimine (EPEI), were synthesized on Si wafers by the "grafting to" method and by applying a combinatorial approach (fabrication of gradient brushes). The combinatorial approach revealed a strong effect of "layer assisted tethering", which allowed us to synthesize hybrid brushes twice as thick as the reference homopolymer brushes. The hybrid brushes are stable thin films that can rapidly and reversibly switch between hydrophilic and hydrophobic states in water and air, respectively. The switching in water affects a rapid release of amino functional groups which can be used to regulate adhesion and reactivity of the material. The switching in air rapidly returns the brush to a hydrophobic state. The hybrid brush is hydrophilic because of two mechanisms: (1) exposure of EPEI chains to the brush-water interface under water, and (2) retention of some fraction of water via swollen EPEI chains (the EPEI chains swell by 2-3 times), which are conserved by a PDMS cap in air. The hybrid brush is wettable under water, and at the same time, the brush is nonwettable in air because water droplets are trapped in a metastable state when the water contact angle is above 90 degrees .     

Ideal tetrafunctional amphiphilic PEG/PDMS conetworks by a dual‐purpose extender/crosslinker. I. Synthesis

The synthesis of a new type of amphiphilic conetwork (APCN) consisting of well‐defined hydrophilic poly(ethylene glycol) (PEG) and hydrophobic polydimethylsiloxane (PDMS) segments is described. The conetwork is ideal (the lengths of each PEG and PDMS chain segments, respectively, are identical) and tetrafunctional (exactly four chains emanate from each crosslink site). The synthesis of the conetworks was achieved by the use of a novel dual‐purpose extender/crosslinker Y (bis [(dimethylsilyl)oxy]‐[(etoxydimethylsilyl)oxy]phenylsilane, (SiPh(SiH)₂OEt)), in two steps: (1) Synthesis of a new linear random multiblock copolymer (MBC) (AY)_n(BY)_m, where A is the hydrophilic PEG and B is the hydrophobic segment, and (2) Crosslinking the multiblocks by catalytic condensation of the SiOEt groups in the Y units. The extender/crosslinker fulfills two totally different functions: First, it extends two incompatible hydrophilic and hydrophobic prepolymers (PEG and PDMS) to a random MBC, and, subsequently, it cross‐links the multiblocks to the target APCN. The synthesis and characterization of the extender/crosslinker is also presented. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4953–4964, 2005     

Properties of poly(dimethylsiloxane)/hydrogel multicomponent systems

The properties of surface‐ and bulk‐modified poly(dimethylsiloxane) (PDMS) were examined. Laser‐induced surface grafting of poly(2‐hydroxyethyl methacrylate) (PHEMA) on PDMS and a sequential method for preparation of interpenetrating polymer networks of PDMS/PHEMA were, respectively, used for surface and bulk modifications. The hydrogel content and water‐uptake capability of the modified samples were also investigated. The modified PDMS samples were examined by performing attenuated total reflection/Fourier transform infrared spectroscopy, dynamic mechanical thermal analysis, scanning electron microscopy, and water contact‐angle measurements. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2145–2156, 2003     

Sensing of liquids by electrically conductive immiscible polypropylene/thermoplastic polyurethane blends containing carbon black

Immiscible polymer blends based on polypropylene/thermoplastic polyurethane (PP/TPU) are interesting host multiphase systems for the incorporation of low concentrations of conductive carbon black (CB) particles. The enhancement of conductivity (and the lower critical CB content for percolation) in the PP/TPU blend is achieved via double percolation, that is, structural and electrical. The CB particles form chainlike network structures within the TPU phase, which exhibit phase continuity of elongated particles within the PP matrix. Moreover, scanning electron microscopy and dynamic mechanical thermal analysis studies indicated that the incorporation of CB particles into the PP/TPU blend has a “compatibilizing” effect, resulting in an enhanced interaction between the two polymers. Extruded PP/TPU/CB filaments produced by a capillary rheometer process at various shear rates were examined as sensing materials for a homologous series of alcohols, that is, methanol, ethanol, and 1‐propanol. All filaments displayed increasing resistance upon exposure to the various alcohols combined with excellent reproducibility and recovery behavior. An attempt is made to identify the dominant mechanisms controlling the sensing process in a CB‐containing immiscible polymer blend characterized by a double‐continuity structure. The interphase region, its quantity, and continuity played a significant role in the liquid‐transport process. Blend composition, filaments' extrusion temperature, and production shear rate level were considered as significant parameters determining the structure and the resultant sensing properties. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1428–1440, 2003     

Hard‐block degradable thermoplastic urethane‐elastomers for electrospun vascular prostheses

Thermoplastic polyurethane (TPU) elastomers with biodegradable chain extenders were synthesized and tested for mechanical performance and biocompatibility. The design of the TPUs was based on structural modification of a mechanically appropriate aromatic isocyanate‐based TPU. As the aromatic isocyanate was substituted with a less toxic but also less “hard” aliphatic isocyanate, the chain extender plays an important role on the mechanical properties. Here, the terephthalate ester chain extender was found to work better than hydroxyl ethyl lactate in providing polymers with mechanical properties similar to commercial aromatic isocyanate‐based TPUs. The polymers were degraded in aqueous solutions at elevated temperatures and compared to polylactic acid (PLA) to partially simulate biodegradation. The lactate‐based TPUs degraded about twice as fast as PLA while the terephthalate‐based TPU degraded much more slowly. The latter material was processed by electrospinning to give a tubular graft approximately the size of a large rat blood vessel. Initial results from implantation of these TPUs into rats are promising and indicate that biodegradation occurs and is likely beneficial to cell proliferation. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

A new soft lithographic route for the facile fabrication of hydrophilic sandwich microchips

Manufacturing materials are an essential element for the fabrication of microfluidic chips. PDMS, the most widely used polymeric material, is associated with apparent disadvantages such as hydrophobic nature, while other materials also suffer from some limitations. In this paper, a new soft lithographic route was proposed for the facile manufacturing of hydrophilic sandwich microchips, using bisphenol A based epoxy acrylate (BABEA) as a new patterning material. The BABEA copolymers are hydrophilic, highly transparent in visible range while highly untransparent when the wavelength is less than 290 nm, and of high replication fidelity. By combining with appropriate monomers, including glycidyl methacrylate, methylmethacrylate, and acrylic acid, the copolymers contain active functional groups, which allows for easy postmodification for desirable functional units. A fabrication procedure was proposed for manufacturing hybrid quartz/BABEA copolymer/quartz microchips. In the procedure, no micromachining equipments, wet etching, or imprinting techniques were involved, making the fabrication approach applicable in ordinary chemistry laboratories. The performance of the prepared microchips was demonstrated in terms of CIEF with UV-whole channel imaging detection. The hydrophilic microchannel ensures stable focusing while the polymeric middle layer acts as a perfectly aligned optical slit for whole channel UV absorbance detection.     

Synthesis and characterization of novel PDMS nanocomposites using POSS derivatives as cross‐linking filler

We report the synthesis and characterization of novel elastomeric nanocomposites containing polyhedral oligomeric silsesquioxanes (POSS) as both the cross‐linker and filler within a polydimethylsiloxane (PDMS) polymer matrix. These polymer composites were prepared through the reaction of octasilane‐POSS (OS‐POSS) with vinyl‐terminated PDMS chains using hydrosilylation chemistry. In addition, larger super‐POSS cross‐linkers, consisting of two pendant hepta(isobutyl)POSS molecules attached to a central octasilane‐POSS core, were also used in the fabrication of the PDMS composites. The chemical incorporation of these POSS cross‐linkers into the PDMS network was verified by solid‐state ¹H magic angle spinning NMR. Based on dynamic mechanical analysis, the PDMS nanocomposites prepared with the octafunctional OS‐POSS cross‐linker exhibited enhanced mechanical properties relative to polymer systems prepared with the tetrafunctional TDSS cross‐linker at equivalent loading levels. The observed improvements in mechanical properties can be attributed to the increased dimensionality of the POSS cross‐linker. The PDMS elastomers synthesized from the larger super‐POSS molecule showed improved mechanical properties relative to both the TDSS and OS‐POSS composites due to the increased volume‐fraction of POSS filler in the polymer matrix. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2589–2596, 2009     

Novel amphiphilic triblocks fitted with photocrosslinkable termini,and their photocrosslinking to conetworks

Two new telechelic amphiphilic triblock copolymers, HE₃‐PEG‐b‐PDMS‐b‐PEG‐HE₃ and HE₃‐PEG‐b‐PDMS‐b‐PEG‐HE₃, i.e., sequence‐reversed triblocks of hydrophilic poly(ethylene glycol) (PEG) and hydrophobic polydimethylsiloxane (PDMS) segments fitted with photocrosslinkable tri[2‐(3,4‐cyclohexane oxide)ethyl‐dimethylsiloxy]silane (HE₃) termini, were synthesized, characterized, photocrosslinked to amphiphilic conetworks (APCNs), and the properties of the APCNs were analyzed. APCNs in which the crosslinking sites are located in the hydrophobic domains exhibited significantly better mechanical properties than those in which the crosslinks were in the hydrophilic domains. The stiff domains formed of the UV‐crosslinkable HE₃ chain‐end substituents provide not only crosslinking but reinforcement as well. The crosslinking/reinforcement efficiency was greatly enhanced by the addition of excess HE₃. Water‐swollen APCNs were optically clear and exhibited mechanical properties appropriate for biomedical application. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 174–185, 2008     

The stability of radio-frequency plasma-treated polydimethylsiloxane surfaces

Polydimethylsiloxane (PDMS) is a widely used material for manufacturing lab-on-chip devices. However, the hydrophobic nature of PDMS is a disadvantage in microfluidic systems. To transform the hydrophobic PDMS surface to hydrophilic, it was treated with radio-frequency (RF) air plasma at 150, 300, and 500 mTorr pressures for up to 30 min. Following the surface treatment, the PDMS specimens were stored in air, deionized water, or 0.14 M NaCl solution at 4 degrees C, 20 degrees C, and 70 degrees C. The change in the hydrophilicity (wettability) of the PDMS surfaces was followed by contact angle measurements and Fourier transform infrared attenuated total reflectance (FTIR-ATR) spectroscopy as a function of time. As an effect of the RF plasma treatment, the contact angles measured on PDMS surfaces dropped from 113 +/- 4 degrees to 9 +/- 3 degrees . The chamber pressure and the treatment time had no or negligible effect on the results. However, the PDMS surface gradually lost its hydrophilic properties in time. The rate of this process is influenced by the difference in the dielectric constants of the PDMS and its ambient environment. It was the smallest at low temperatures in deionized water and largest at high temperatures in air. Apparently, the OH groups generated on the PDMS surface during the plasma treatment tended toward a more hydrophilic/less hydrophobic environment during the relaxation processes. The correlation between the FTIR-ATR spectral information and the contact angle data supports this interpretation.     

Thermal transitions of benzene in copolymers and interpenetrating polymer networks based on hydrophilic and hydrophobic components: Experimental evidence of hydrophobic interaction

Thermal transitions of benzene in a hydrophobic polymer network have been explained by us in terms of the phase diagram of the polymer‐solvent system. In this work, we executed a similar study on copolymers and interpenetrating polymer networks (IPNs) with controllable hydrophilic/hydrophobic ratios. Copolymers and IPNs were swollen with different amounts of benzene and subjected to cooling and heating scans with differential scanning calorimetry (DSC). Synthesis of the IPNs was carried out in such a way that phase separation appeared, and three qualitatively different types of DSC thermograms were identified depending on the benzene content of IPN. Thermal transitions of benzene in the hydrophilic/hydrophobic copolymers can also be explained as a consequence of the phase diagram of the system, but an increase in the glass‐transition temperature of the system can be correlated with the interactions among the hydrophilic groups of the copolymer. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 1713–1721, 2003     

Ideal tetrafunctional amphiphilic PEG/PDMS conetworks by a dual‐purpose extender/crosslinker. II. Characterization and properties of water‐swollen membranes

Select characteristics and properties of a series of ideal tetrafunctional amphiphilic conetworks consisting of random poly(ethylene glycol) (PEG) and polydimethylsiloxane (PDMS) segments crosslinked by a novel dual‐purpose crosslinker/extender were determined. The overall composition of the conetworks was varied in the 16–40% PEG range, and membranes were prepared by polymerizing/crosslinking charges in molds. Membranes were characterized by equilibrium swelling (both in water and n‐heptane) and by determining their oxygen permeabilities and select mechanical properties. Swelling in water increases, whereas in heptane it decreases with increasing PEG content. Significant swelling in both solvents indicates bicontinuous (bipercolating) PEG and PDMS phases. Bicontinuity is reached with ～13% PEG in the conetworks. The oxygen permeabilities of optically clear water‐swollen membranes containing 24, 32, and 40 wt % PEG are ～350, ～245 and ～185 barrers, respectively, i.e., oxygen permeability decreases by increasing the hydrophilic constituent. These oxygen permeabilities are far superior to those of contemporary soft contact lenses. The tensile strengths and moduli of water‐swollen membranes decrease, while elongations increase, with increasing PEG content. Dry membranes exhibit first order transitions at ?52 and ～46 °C indicating phase‐separated crystalline PDMS and PEG domains, respectively. Both dry and water‐swollen membranes are optically clear, indicating the presence of PEG and PDMS domains with dimensions well below the wavelength of visible light. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4965–4971, 2005