Crystallization kinetics and morphology of biodegradable poly(butylene succinate‐co‐propylene succinate)s

The crystallization behavior of biodegradable poly(butylene succinate) and copolyesters poly(butylene succinate‐co‐propylene succinate)s (PBSPS) was investigated by using ¹H NMR, DSC and POM, respectively. Isothermal crystallization kinetics of the polyesters has been analyzed by the Avrami equation. The 2.2‐2.8 range of Avrami exponential n indicated that the crystallization mechanism was a heterogeneous nucleation with spherical growth geometry in the crystallization process of polyesters. Multiple melting peaks were observed during heating process after isothermal crystallization, and it could be explained by the melting and recrystallization model. PBSPS was identified to have the same crystal structure with that of PBS by using wide‐angle X‐ray diffraction (WAXD), suggesting that only BS unit crystallized while the PS unit was in an amorphous state. The crystal structure of polyesters was not affected by the crystallization temperatures, too. Besides the normal extinction crosses under the POM, the double‐banded extinction patterns with periodic distance along the radial direction were also observed in the spherulites of PBS and PBSPS. The morphology of spherulites strongly depended on the crystallization temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 420–428, 2007     

Melting behaviors,crystallization kinetics,and spherulitic morphologies of poly(butylene succinate) and its copolyester modified with rosin maleopimaric acid anhydride

This article investigated the melting behaviors, crystallization kinetics, and spherulitic morphologies of poly(butylene succinate) (PBS) and its copolyester (PBSR) modified with rosin maleopimaric acid anhydride, using wide‐angle X‐ray diffraction, differential scanning calorimeter (DSC), and polarized optical microscope. Subsequent DSC scans of isothermally crystallized PBS and PBSR exhibited two melting endotherms, respectively, which was due to the melt‐recrystallization process occurring during the DSC scans. The equilibrium melting point of PBSR (125.9 °C) was lower than that of PBS (139 °C). The commonly used Avrami equation was used to describe the isothermal crystallization kinetics. For nonisothermal crystallization studies, the model combining Avrami equation and Ozawa equation was employed. The result showed a consistent trend in the crystallization process. The crystallization rate was decreased, the perfection of crystals was decreased, the recrystallization was reduced, and the spherulitic morphologies were changed when the huge hydrogenated phenanthrene ring was added into the chain of PBS. The activation energy (ΔE) for the isothermal crystallization process determined by Arrhenius method was 255.9 kJ/mol for PBS and 345.7 kJ/mol for PBSR. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 900–913, 2006     

Effects of comonomer sequential structure on thermal and crystallization behaviors of biodegradable poly(butylene succinate‐co‐butylene terephthalate)s

In this work, new investigations on the effect of comonomer sequential structure on the thermal and crystallization behaviors and biodegradability have been implemented for the biodegradable poly(butylene succinate‐co‐butylene terephthalate) (PBST) as well as aliphatic poly(butylene succinate) (PBS). At first, these copolyesters were efficiently synthesized from dimethyl succinate and/or dimethyl terephthalate and 1,4‐butanediol via condensation polymerization in bulk. Subsequently, their molecular weights and macromolecular chain structures were analyzed by gel permeation chromatography (GPC) and nuclear magnetic resonance (NMR) spectroscopy. By means of differential scanning calorimeter (DSC) and wide‐angle X‐ray diffractometer (WAXD), thermal and crystallization behaviors of these synthesized aromatic–aliphatic copolyesters were further explored. It was demonstrated that the synthesized copolyesters were revealed to have random comonomer sequential structures with thermal and crystallization properties strongly depending on their comonomer molar compositions, and that crystal lattice structures of the new crystallizable copolyesters shifted from the monoclinic crystal of semicrystalline PBS to triclinic lattice of the poly(butylene terephthalate) (PBT) with increasing the terephthalate comonomer composition, and the minor comonomer components were suggested to be trapped in the crystallizable component domains as defects. In addition, the enzymatic degradability was also characterized for the copolyesters film samples. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1635–1644, 2006     

Analysis of the complex thermal behavior of poly(L‐lactic acid) film. I. Samples crystallized from the glassy state

The melting behavior of poly(L ‐lactic acid) film crystallized from the glassy state, either isothermally or nonisothermally, was studied by wide angle X‐ray diffraction (WAXD), small angle X‐ray scattering (SAXS), differential scanning calorimetry (DSC), and temperature‐modulated differential scanning calorimetry (TMDSC). Up to three crystallization and two melting peaks were observed. It was concluded that these effects could largely be accounted for on the basis of a “melt‐recrystallization” mechanism. When molecular weight is low, two melting endotherms are readily observed. But, without TMDSC, the double melting phenomena of high molecular weight PLLA is often masked by an exotherm just prior to the final melting, as metastable crystals undergo melt‐recrystallization during heating in the DSC. The appearance of a double cold‐crystallization peak during the DSC heating scan of amorphous PLLA film is the net effect of cold crystallization and melt‐recrystallization of metastable crystals formed during the initial cold crystallization. Samples cold‐crystallized at 80 and 90 °C did not exhibit a long period, although substantial crystallinity developed. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3200–3214, 2006     

Crystallization kinetics and morphology of poly(butylene succinate‐co‐adipate)

The crystallization kinetics of biodegradable poly(butylene succinate‐co‐adipate) (PBS/A) copolyester was investigated by using differential scanning calorimetry (DSC) and polarized optical microscopy (POM), respectively. The Avrami and Ozawa equations were used to analyze the isothermal and nonisothermal crystallization kinetics, respectively. By using wide‐angle X‐ray diffraction (WAXD), PBS/A was identified to have the same crystal structure with that of PBS. The spherulitic growth rates of PBS/A measured in isothermal conditions are very well comparable with those measured by nonisothermal procedures (cooling rates ranged from 0.5 to 15 °C/min). The kinetic data were examined with the Hoffman–Lauritzen nucleation theory. The observed spherulites of PBS/A with different shapes and textures strongly depend on the crystallization temperatures. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3231–3241, 2005     

Influence of copolymer composition of polyestercarbonate on miscibility with poly(butylene terephthalate)

Blends of poly(butylene terephthalate) (PBT) and polyestercarbonate (PEC), copolyesters consisting of polycarbonate (PC) and polyarylate (PAr), have been studied by thermal analysis to determine miscibility. The PBT blends with PAr and PEC containing 30 wt % of carbonate unit or less appeared to be miscible, and the tendency for stable single‐phase was observed to decrease as the content of carbonate unit in PEC copolymer increased. As determined with the crystalline phase behavior, the miscibility of PEC with PBT appeared to have a maximum around 10 ∼ 30 wt % of carbonate content in PEC copolymer, and this result was attributed to the internal repulsion effect between ester and carbonate repeating units in PEC copolymer. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 803–811, 2000     

Melting and crystallization of poly(butylene terephthalate) by temperature‐modulated and superfast calorimetry

Quantitative temperature‐modulated differential scanning calorimetry (TMDSC) and superfast thin‐film chip calorimetry (SFCC) are applied to poly(butylene terephthalate)s (PBT) of different thermal histories. The data are compared with those of earlier measured heat capacities of semicrystalline PBT by adiabatic calorimetry and standard DSC. The solid and liquid heat capacities, which were linked to the vibrational and conformational molecular motion, serve as references for the quantitative analyses. Using TMDSC, the thermodynamic and kinetic responses are separated between glass and melting temperature. The changes in crystallinity are evaluated, along with the mobile–amorphous and rigid–amorphous fractions with glass transitions centered at 314 and 375 K. The SFCC showed a surprising bimodal change in crystallization rates with temperature, which stretches down to 300 K. The earlier reported thermal activity at about 248 K was followed by SFCC and TMDSC and could be shown to be an irreversible endotherm and is not caused by a glass transition and rigid–amorphous fraction, as assumed earlier. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1364–1377, 2006     

X‐ray studies on the double melting behavior of poly(butylene terephthalate)

The double melting behavior of poly(butylene terephthalate) (PBT) was studied with differential scanning calorimetry (DSC) and wide‐angle X‐ray analysis. DSC melting curves of melt‐crystallized PBT samples, which we prepared by cooling from the melt (250 °C) at various cooling rates, showed two endothermic peaks and an exothermic peak located between these melting peaks. The cooling rate effect on these peaks was investigated. The melt‐crystallized PBT sample cooled at 24 K min^?1 was heated at a rate of 1 K min^?1, and its diffraction patterns were obtained successively at a rate of one pattern per minute with an X‐ray measurement system equipped with a position‐sensitive proportional counter. The diffraction pattern did not change in the melting process, except for the change in its peak height. This suggests that the double melting behavior does not originate from a change in the crystal structure. The temperature dependence of the diffraction intensity was obtained from the diffraction patterns. With increasing temperature, the intensity decreased gradually in the low‐temperature region and then increased distinctly before a steep decrease due to the final melting. In other words, the temperature‐dependence curve of the diffraction intensity showed a peak that is interpreted as proof of the recrystallization in the melting process. The peak temperature was 216 °C. The temperature‐dependence curve of the enthalpy change obtained by the integration of the DSC curve almost coincided with that of the diffraction intensity. The double melting behavior in the heating process of PBT is concluded to originate from the increase of crystallinity, that is, recrystallization. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 2005–2015, 2001     

Effect of poly(butylene succinate) crystals on spherulitic growth of poly(ethylene oxide) in binary blends of the two substances

The effects of the lamellar growth direction, extinction rings, and spherulitic boundaries of poly(butylene succinate) (PBSU) on the spherulitic growth of poly(ethylene oxide) (PEO) were investigated in miscible blends of the two crystalline polymers. In the crystallization process from a homogeneous melt, PBSU first developed volume‐filling spherulites, and then PEO spherulites nucleated and grew inside the PBSU spherulites. The lamellar growth direction of PEO was identical with that of PBSU even when the PBSU content was about 5 wt %. PEO, which intrinsically does not exhibit banded spherulites, showed apparent extinction rings inside the banded spherulites of PBSU. The growth rate of a PEO spherulite, G_PEO, was influenced not only by the blend composition and the crystallization temperature of PEO, but also by the growth direction with respect to PBSU lamellae, the boundaries of PBSU spherulites, and the crystallization temperature of PBSU, T_PBSU. The value of G_PEO first increased with decreasing T_PBSU when a PEO spherulite grew inside a single PBSU spherulite. Then, G_PEO decreased when T_PBSU was further decreased and a PEO spherulite grew through many tiny PBSU spherulites. This behavior was discussed based on the aforementioned factors affecting G_PEO. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 539–547, 2009     

Lamellar structural changes in miscible crystalline polymer blends during melting and crystallization processes,as studied by real‐time small‐angle X‐ray scattering measurements

Real‐time small‐angle X‐ray scattering (SAXS) measurement using synchrotron radiation was applied to study the lamellar structural changes in miscible crystalline polymer blends of poly(1,4‐butylene succinate) (PBSU) and poly(vinylidene fluoride) (PVDF) during melting and crystallization processes. The lamella of PBSU is either included in the interlamellar region of PVDF (interlamellar inclusion structure), or rejected from the interlamellar region of PVDF (interlamellar exclusion structure). The two lamellar structures coexists in the melt‐quenched samples of the PBSU/PVDF = 30/70 blend. Only the interlamellar exclusion structure exists in the drawn films of the PBSU/PVDF = 30/70 blend. The real‐time SAXS results show that the interlamellar exclusion structure in these samples is irreversibly transformed into the interlamellar inclusion structure by heating the sample above the melting temperature of PBSU and that the PBSU chains are crystallized between the lamellae of PVDF during the cooling process. The factors controlling the lamellar structural changes are possibly a balance of the miscibility and the chain exclusion by tie‐molecules and/or the chain diffusion under confinement by the lamellae of PVDF with higher melting temperature. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 1959–1969, 2007     

Thermal memory of poly(3‐hydroxybutyrate) using temperature‐modulated differential scanning calorimetry

The influence of thermal history on morphology, melting, and crystallization behavior of bacterial poly(3‐hydroxybutyrate) (PHB) has been investigated using temperature‐modulated DSC (TMDSC), wide‐angle X‐ray diffraction (WAXRD) and polarized optical microscopy (POM). Various thermal histories were imparted by crystallization with continuous and different modulated cooling programs that involved isoscan and cool–heat segments. The subsequent melting behavior revealed that PHB experienced secondary crystallization during heating and the extent of secondary crystallization varied with the cooling treatment. PHB crystallized under slow, continuous, and moderate cooling rates were found to exhibit double melting behavior due to melting of TMDSC scan‐induced secondary crystals. PHB underwent considerable secondary crystallization/annealing that took place under modulated cooling conditions. The overall melting behavior was interpreted in terms of recrystallization and/or annealing of crystals. Interestingly, the PHB analyzed by temperature modulation programs showed a broad exotherm before the melting peak in the nonreversing heat capacity curve and a multiple melting reversing curve, verifying that the melting–recrystallization and remelting process was operative. WAXRD and POM studies supported the correlations from DSC and TMDSC results. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 70–78, 2006     

Crystallization behavior and thermal property of biodegradable poly(butylene succinate)/functional multi-walled carbon nanotubes nanocomposite

Biodegradable poly(butylene succinate) (PBSU)/functional multi-walled carbon nanotubes (f-MWNTs) nanocomposite were prepared by melt compounding. Nonisothermal crystallization and subsequent melting behavior, isothermal crystallization kinetics, spherulitic morphology, and crystal structure of neat PBSU and its nanocomposite were studied by differential scanning calorimetry, optical microscopy and wide angle X-ray diffraction in detail. The presence of f-MWNTs has a significant heterogeneous nucleation effect on the crystallization and morphology of PBSU, resulting in that the crystallization is enhanced during both nonisothermal and isothermal crystallization in the nanocomposite. Moreover, the crystal structure of PBSU is not modified by f-MWNTs in the nanocomposite. The thermogravimetric analysis illustrates an improvement in thermal stability of PBSU by around 10 °C in the presence of f-MWNTs compared with that of neat PBSU.     

Miscibility,melting, and crystallization of poly(butylene‐2,6‐naphthalate)/poly(ether imide) blends

We prepared blends of poly(butylene‐2,6‐naphthalate) (PBN) and poly(ether imide) (PEI) by solution‐casting from dichloroacetic acid solutions. The miscibility, crystallization, and melting behavior of the blends were investigated with differential scanning calorimetry (DSC) and dynamic mechanical analysis. PBN was miscible with PEI over the entire range of compositions, as shown by the existence of single composition‐dependent glass‐transition temperatures. In addition, a negative polymer–polymer interaction parameter was calculated, with the Nishi–Wang equation, based on the melting depression of PBN. In nonisothermal crystallization investigations, the depression of the crystallization temperature of PBN depended on the composition of the blend and the cooling rate; the presence of PEI reduced the number of PBN segments migrating to the crystallite/melt interface. Melting, recrystallization, and remelting processes occurring during the DSC heating scan caused the occurrence of multiple melting endotherms for PBN. We explored the effects of various experimental conditions on the melting behavior of PBN/PEI blends. The extent of recrystallization of the PBN component during DSC heating scans decreased as the PEI content, the heating rate, the crystallization temperature, and the crystallization time increased. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 1694–1704, 2004     

Influence of low multi‐walled carbon nanotubes loadings on the crystallization behavior of biodegradable poly(butylene succinate) nanocomposites

Biodegradable poly(butylene succinate) (PBSU)/carboxyl‐functionalized multi‐walled carbon nanotubes (f‐MWNTs) nanocomposites were prepared via solution casting method at low f‐MWNTs loadings of 0.5 and 1 wt%, respectively, in this work. Scanning and transmission electron microscopic observations reveal a fine dispersion of f‐MWNTs throughout the PBSU matrix. Non‐isothermal melt crystallization at different cooling rates, isothermal melt crystallization at different crystallization temperatures, spherulitic morphology, and crystal structure of neat PBSU and its nanocomposites were investigated with various techniques in detail. The addition of f‐MWNTs is found to enhance the crystallization of PBSU, apparently in the nanocomposites during both nonisothermal and isothermal melt crystallization, due to the heterogeneous nucleation effect; however, the crystallization mechanism and crystal structure of PBSU remain almost unchanged. Effect of the presence of f‐MWNTs and their loadings on the thermodynamic driving force for nucleation and nucleation activity of PBSU was evaluated quantitatively through two methods. Moreover, it is found that incorporating with 1 wt% f‐MWNTs significantly improves the storage modulus of PBSU in the nanocomposites by about 147% at room temperature as compared with that of neat PBSU. Copyright © 2010 John Wiley & Sons, Ltd.     

Fully biodegradable blends of poly(butylene succinate) and poly(butylene carbonate): Miscibility, thermal properties, crystallization behavior and mechanical properties

Fully biodegradable poly(butylene succinate) (PBS) and poly(butylene carbonate) (PBC) blends were prepared by melt blending. Miscibility, thermal properties, crystallization behavior and mechanical properties of PBS/PBC blends were investigated by scanning electron microscopy (SEM), phase contrast optical microscopy (PCOM), differential scanning calorimetry (DSC), wide angle X-ray diffraction (WAXD) and mechanical properties tests. The SEM and PCOM results indicated that PBS was immiscible with PBC. The WAXD results showed that the crystal structures of both PBS and PBC were not changed by blending and the two components crystallized separately in the blends. The isothermal crystallization data showed that the crystallization rate of PBS increased with the increase of PBC content in the blends. The impact strength of PBS was improved significantly by blending with PBC. When the PBC content was 40%, the impact strength of PBS was increased by nearly 9 times.     

Transesterification and crystallization behavior of poly(butylene succinate)/poly(butylene terephthalate) block copolymers

The block copolymers of poly(butylene succinate) (PBS) and poly(butylene terephthalate) (PBT) were synthesized by melt processing for different times. The sequence distribution, thermal properties, and crystallization behavior were investigated over a wide range of compositions. For PBS/PBT block copolymers it was confirmed by statistical analysis from ¹H-NMR data that the degree of randomness (B) was below 1. The melting peak (T_m) gradually moved to lower temperature with increasing melt processing time. It can be seen that the transesterification between PBS and PBT leads to a random copolymer. From the X-ray diffraction diagrams, only the crystal structure of PBS appeared in the M1 copolymer (PBS 80 wt %) and that of PBT appeared in the M3 (PBS 50 wt %) to M5 (PBS 20 wt %) copolymers. © 1998 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 36: 147–156, 1998     

Thermal analysis of the multiple melting behavior of poly(butylene succinate‐co‐adipate)

The melting behavior of poly(butylene succinate‐co‐adipate) (PBSA) isothermally crystallized from the melt was investigated by differential scanning calorimetry. Triple, double, or single melting endotherms were observed in subsequent heating scan for the samples isothermally crystallized at different temperatures. These endothermic peaks were labeled as I, II, and III for low‐, middle‐, and high‐temperature melting endotherms, respectively. The independence of endotherm III to the crystallization temperature, the existence of an exothermic crystallization peak just below the endotherm III, and the heating rate dependence of endotherm III indicated that endotherm III was due to the remelting of recrystallized lamellar during a heating scan. The influence of crystallization time on the melting behavior of PBSA showed that endotherms II and III developed prior to endotherm I; endotherm III developed rather simultaneously with endotherm II. Further investigation showed that the peak temperature of endotherm I increased linearly with the logarithm of the crystallization time. It suggested that endotherm II was attributed to the melting of the primary lamellae, while endotherm I was due to the melting of secondary lamellae. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 3077–3082, 2005     

Synthesis,characterization and isothermal crystallization behavior of poly(butylene succinate)‐b‐poly(diethylene glycol succinate) multiblock copolymers

In order to modify the properties of poly(butylene succinate), poly(diethylene glycol succinate) (PDGS) segment was incorporated by chain‐extension reaction of dihydroxyl‐terminated PBS and PDGS precursors using hexamethylene diisocyanate as a chain extender to form PBS‐b‐PDGS multiblock copolymers. The chemical structure and basic physical properties of the multiblock copolyesters were characterized by nuclear magnetic resonance spectroscopy, differential scanning calorimeter (DSC), wide angle X‐ray diffraction, and tensile testing. The results suggested that the incorporation of PDGS segments would increase the elongation at break of PBS significantly while decrease its melting temperature and crystallization temperature slightly. The isothermal crystallization kinetics studied by DSC and polarized optical microscopy indicated that the crystallization rate of the multiblock polymers decreased gradually with increasing PDGS segment content while the crystallization mechanism kept unchanged and the spherulitic growth rate of the multiblock copolymers decreased gradually with increase in PDGS content due to its diluent effect to the crystallization of PBS segments. Copyright © 2015 John Wiley & Sons, Ltd.     

Enhanced nonisothermal crystallization of a series of poly(butylene succinate‐co‐terephthalate) biopolyesters by poly(vinyl butyral)

Enhanced nonisothermal crystallization of a series of poly(butylene succinate‐co‐terephthalate) (PBST) by poly(vinyl butyral) (PVB) as a macromolecular nucleating agent has been examined systematically with various techniques and theoretical modeling. The role of PVB depends strongly on the butylene terephthalate content, PVB content, and cooling rate. The (0.3–0.7 wt %) PVB reduces the spherulitic size, but considerably increases the peak temperature of crystallization, for example, by 28 °C for the PBST with 50 mol % terephthalic acid. The effects of PVB are believed to stem from its unique molecular structure. Both the hydroxyl and butyral groups of PVB may synergistically participate in nucleating PBSTs for crystallization because of favorable secondary interaction and affinity of butyral groups with butylene succinate units of PBSTs. Only the Tobin model suffices to describe the nonisothermal crystallization kinetics, while the modified Avrami model is suitable for limited crystallinity. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 658–672     

Temperature‐modulated differential scanning calorimetry studies on the origin of double melting peaks in isothermally melt‐crystallized poly(L‐lactic acid)

In this work, the melting behaviors of nonisothermally and isothermally melt‐crystallized poly(L ‐lactic acid) (PLLA) from the melt were investigated with differential scanning calorimetry (DSC) and temperature‐modulated differential scanning calorimetry (TMDSC). The isothermal melt crystallizations of PLLA at a temperature in the range of 100–110 °C for 120 min or at 110 °C for a time in the range of 10–180 min appeared to exhibit double melting peaks in the DSC heating curves of 10 °C/min. TMDSC analysis revealed that the melting–recrystallization mechanism dominated the formation of the double melting peaks in PLLA samples following melt crystallizations at 110 °C for a shorter time (≤30 min) or at a lower temperature (100, 103, or 105 °C) for 120 min, whereas the double lamellar thickness model dominated the formation of the double melting peaks in those PLLA samples crystallized at a higher temperature (108 or 110 °C) for 120 min or at 110 °C for a longer time (≥45 min). © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 466–474, 2007